We present systematic investigations on the physics,detection performance and inversion of logging-while-drilling extradeep azimuthal resistivity measurements(EDARM).First,the definitions of EDRAM measurements are dis...We present systematic investigations on the physics,detection performance and inversion of logging-while-drilling extradeep azimuthal resistivity measurements(EDARM).First,the definitions of EDRAM measurements are discussed,followed by the derivation of the attenuation and phase-shift geometrical factors to illustrate the relative contributions of formation units to the observed signals.Then,a new definition of detection depth,which considers the uncertainty of inversion results caused by the data noise,is proposed to quantify the detection capability of ED ARM.Finally,the B ayesian theory associated with Markov chain Monte Carlo sampling is introduced for fast processing of EDARM data.Numerical results show that ED ARM is capable of detecting the azimuth and distance of remote bed boundaries,and the detection capability increases with increasing spacing and resistivity contrast.The EDARM tool can accommodate a large range of formation resistivity and is able to provide the resistivity anisotropy at arbitrary relative dipping angles.In addition,multiple bed boundaries and reservoir images near the borehole are readily obtained by using the Bayesian inversion.展开更多
Panel methods for the calculation of wavemaking resistance result in a linear equation system for the unknown singularities.The coefficient matrix is full but not well conditioned.In this paper an incomplete LU decomp...Panel methods for the calculation of wavemaking resistance result in a linear equation system for the unknown singularities.The coefficient matrix is full but not well conditioned.In this paper an incomplete LU decomposition (ILU) method and a combined multigrid ILU method are used to solve the linear system.Systematic computations using the ILU method have shown that the CPU time can be reduced to 30% to 40% of that using an incomplete Gaussian elimination method. In the proposed multigrid ILU method an averaged restriction and a piecewise constant prolongation are used.The construction of the coefficient matrix at coarse levels is based on geometrical considerations.It turns out that the condition of the relative consistency is fulfilled.Comparison computations have shown that nearly the same results were obtained.However,due to additional CPU time needed for the execution of the matrix vector products in the restriction and the prolongation proceses of the multigrid method,a further reduction of the total CPU time could not be reailized.展开更多
Making an exact computation of added resistance in sea waves is of high interest due to the economic effects relating to ship design and operation. In this paper, a B-spline based method is developed for computation o...Making an exact computation of added resistance in sea waves is of high interest due to the economic effects relating to ship design and operation. In this paper, a B-spline based method is developed for computation of added resistance. Based on the potential flow assumption, the velocity potential is computed using Green＇s formula. The Kochin function is applied to compute added resistance using Maruo＇s far-field method, the body surface is described by a B-spline curve and potentials and normal derivation of potentials are also described by B-spline basis functions and B-spline derivations. A collocation approach is applied for numerical computation, and integral equations are then evaluated by applying Gauss–Legendre quadrature. Computations are performed for a spheroid and different hull forms; results are validated by a comparison with experimental results. All results obtained with the present method show good agreement with experimental results.展开更多
A convenient numerical calculation method (inverse spline interpolation) for all-time apparent resistivity intransient electromagnetic method (TEM) is proposed in this paper. Characteristic of early and late normalize...A convenient numerical calculation method (inverse spline interpolation) for all-time apparent resistivity intransient electromagnetic method (TEM) is proposed in this paper. Characteristic of early and late normalized inductiveelectromotive force was investigated. According to the turning point, the transient process is divided into the earlyphase, the turning point, and the late phase. Afterwards, apparent resistivity is obtained through inverse spline interpo-lation in the early and the late phases, respectively. Finally, the resistivities of the early-time and the late-time wereconnected together by the turning point. The result shows that the inverse spline method is feasible and the method alsolays a foundation for initial model construction in the TEM automatic inversion.展开更多
In this paper, Ce_(0.2)Zr_(0.8)O_2 composite supports were prepared by different Ce-addition methods including impregnation of cerium(CeZr-imp), impregnation of citric acid and cerium(CeZr-CA) simultaneously and depos...In this paper, Ce_(0.2)Zr_(0.8)O_2 composite supports were prepared by different Ce-addition methods including impregnation of cerium(CeZr-imp), impregnation of citric acid and cerium(CeZr-CA) simultaneously and deposition precipitation method(CeZr-DP), respectively. The as-prepared supports were applied to prepare 10 wt% MoO_3/Ce_(0.2)Zr_(0.8)O_2 catalysts for sulfur-resistant methanation. The N_2 adsorption/desorption,X-ray diffraction(XRD), Raman spectroscopy(RS), X-ray photoelectron(XPS), temperature-programmed reduction by hydrogen(H_2-TPR) were undertaken to get textural properties, morphological information and structures of the catalysts. The results showed that Mo O_3 was highly dispersed on the surface of these three supports and Ce was mostly of coexisted in Ce^(4+)/Ce^(3+) redox pairs. Compared with Mo/CeZrimp, the CO conversion increased by 10% and 15% for Mo/CeZr-CA and Mo/CeZr-DP, respectively. This was mainly attributed to the larger specific surface area, Ce^(3+) concentration and content of active MoS_2 on the surface of catalysts.展开更多
Optimization analysis and computational fluid dynamics （CFDs） have been applied simultaneously, in which a parametric model plays an important role in finding the optimal solution. However, it is difficult to create...Optimization analysis and computational fluid dynamics （CFDs） have been applied simultaneously, in which a parametric model plays an important role in finding the optimal solution. However, it is difficult to create a parametric model for a complex shape with irregular curves, such as a submarine hull form. In this study, the cubic Bezier curve and curve-plane intersection method are used to generate a solid model of a parametric submarine hull form taking three input parameters into account： nose radius, tail radius, and length-height hull ratio （L/H）. Application program interface （API） scripting is also used to write code in the ANSYS DesignModeler. The results show that the submarine shape can be generated with some variation of the input parameters. An example is given that shows how the proposed method can be applied successfully to a hull resistance optimization case. The parametric design of the middle submarine type was chosen to be modified. First, the original submarine model was analyzed, in advance, using CFD. Then, using the response surface graph, some candidate optimal designs with a minimum hull resistance coefficient were obtained. Further, the optimization method in goal-driven optimization （GDO） was implemented to find the submarine hull form with the minimum hull resistance coefficient （Ct）. The minimum C, was obtained. The calculated difference in （7, values between the initial submarine and the optimum submarine is around 0.26%, with the C, of the initial submarine and the optimum submarine being 0.001 508 26 and 0.001 504 29, respectively. The results show that the optimum submarine hull form shows a higher nose radius （rn） and higher L/H than those of the initial submarine shape, while the radius of the tail （r1） is smaller than that of the initial shape.展开更多
基金co-funded by Chinese Postdoctoral Science Foundation(2018M640663)the National Natural Science Foundation of China(41474100,41574118,41674131)National Science and Technology Major Project of the Ministry of Science and Technology of China(2017ZX05009-001)
文摘We present systematic investigations on the physics,detection performance and inversion of logging-while-drilling extradeep azimuthal resistivity measurements(EDARM).First,the definitions of EDRAM measurements are discussed,followed by the derivation of the attenuation and phase-shift geometrical factors to illustrate the relative contributions of formation units to the observed signals.Then,a new definition of detection depth,which considers the uncertainty of inversion results caused by the data noise,is proposed to quantify the detection capability of ED ARM.Finally,the B ayesian theory associated with Markov chain Monte Carlo sampling is introduced for fast processing of EDARM data.Numerical results show that ED ARM is capable of detecting the azimuth and distance of remote bed boundaries,and the detection capability increases with increasing spacing and resistivity contrast.The EDARM tool can accommodate a large range of formation resistivity and is able to provide the resistivity anisotropy at arbitrary relative dipping angles.In addition,multiple bed boundaries and reservoir images near the borehole are readily obtained by using the Bayesian inversion.
文摘Panel methods for the calculation of wavemaking resistance result in a linear equation system for the unknown singularities.The coefficient matrix is full but not well conditioned.In this paper an incomplete LU decomposition (ILU) method and a combined multigrid ILU method are used to solve the linear system.Systematic computations using the ILU method have shown that the CPU time can be reduced to 30% to 40% of that using an incomplete Gaussian elimination method. In the proposed multigrid ILU method an averaged restriction and a piecewise constant prolongation are used.The construction of the coefficient matrix at coarse levels is based on geometrical considerations.It turns out that the condition of the relative consistency is fulfilled.Comparison computations have shown that nearly the same results were obtained.However,due to additional CPU time needed for the execution of the matrix vector products in the restriction and the prolongation proceses of the multigrid method,a further reduction of the total CPU time could not be reailized.
文摘Making an exact computation of added resistance in sea waves is of high interest due to the economic effects relating to ship design and operation. In this paper, a B-spline based method is developed for computation of added resistance. Based on the potential flow assumption, the velocity potential is computed using Green＇s formula. The Kochin function is applied to compute added resistance using Maruo＇s far-field method, the body surface is described by a B-spline curve and potentials and normal derivation of potentials are also described by B-spline basis functions and B-spline derivations. A collocation approach is applied for numerical computation, and integral equations are then evaluated by applying Gauss–Legendre quadrature. Computations are performed for a spheroid and different hull forms; results are validated by a comparison with experimental results. All results obtained with the present method show good agreement with experimental results.
基金Project 40344022 supported by National Natural Science Foundation of China
文摘A convenient numerical calculation method (inverse spline interpolation) for all-time apparent resistivity intransient electromagnetic method (TEM) is proposed in this paper. Characteristic of early and late normalized inductiveelectromotive force was investigated. According to the turning point, the transient process is divided into the earlyphase, the turning point, and the late phase. Afterwards, apparent resistivity is obtained through inverse spline interpo-lation in the early and the late phases, respectively. Finally, the resistivities of the early-time and the late-time wereconnected together by the turning point. The result shows that the inverse spline method is feasible and the method alsolays a foundation for initial model construction in the TEM automatic inversion.
基金Financial supports from the National High Technology Research and Development Program of China (863 Project) (2015AA050504)the National Natural Science Foundation of China (21576203)
文摘In this paper, Ce_(0.2)Zr_(0.8)O_2 composite supports were prepared by different Ce-addition methods including impregnation of cerium(CeZr-imp), impregnation of citric acid and cerium(CeZr-CA) simultaneously and deposition precipitation method(CeZr-DP), respectively. The as-prepared supports were applied to prepare 10 wt% MoO_3/Ce_(0.2)Zr_(0.8)O_2 catalysts for sulfur-resistant methanation. The N_2 adsorption/desorption,X-ray diffraction(XRD), Raman spectroscopy(RS), X-ray photoelectron(XPS), temperature-programmed reduction by hydrogen(H_2-TPR) were undertaken to get textural properties, morphological information and structures of the catalysts. The results showed that Mo O_3 was highly dispersed on the surface of these three supports and Ce was mostly of coexisted in Ce^(4+)/Ce^(3+) redox pairs. Compared with Mo/CeZrimp, the CO conversion increased by 10% and 15% for Mo/CeZr-CA and Mo/CeZr-DP, respectively. This was mainly attributed to the larger specific surface area, Ce^(3+) concentration and content of active MoS_2 on the surface of catalysts.
基金Supported by the Ministry of Research,Technology,and Higher Education Republic of Indonesia,through the Budget Implementation List(DIPA)of Diponegoro University,Grant No.DIPA-023.04.02.189185/2014,December 05,2013
文摘Optimization analysis and computational fluid dynamics （CFDs） have been applied simultaneously, in which a parametric model plays an important role in finding the optimal solution. However, it is difficult to create a parametric model for a complex shape with irregular curves, such as a submarine hull form. In this study, the cubic Bezier curve and curve-plane intersection method are used to generate a solid model of a parametric submarine hull form taking three input parameters into account： nose radius, tail radius, and length-height hull ratio （L/H）. Application program interface （API） scripting is also used to write code in the ANSYS DesignModeler. The results show that the submarine shape can be generated with some variation of the input parameters. An example is given that shows how the proposed method can be applied successfully to a hull resistance optimization case. The parametric design of the middle submarine type was chosen to be modified. First, the original submarine model was analyzed, in advance, using CFD. Then, using the response surface graph, some candidate optimal designs with a minimum hull resistance coefficient were obtained. Further, the optimization method in goal-driven optimization （GDO） was implemented to find the submarine hull form with the minimum hull resistance coefficient （Ct）. The minimum C, was obtained. The calculated difference in （7, values between the initial submarine and the optimum submarine is around 0.26%, with the C, of the initial submarine and the optimum submarine being 0.001 508 26 and 0.001 504 29, respectively. The results show that the optimum submarine hull form shows a higher nose radius （rn） and higher L/H than those of the initial submarine shape, while the radius of the tail （r1） is smaller than that of the initial shape.
