The adsorption of dedecyltrimethylammoium chloride(DTAC) and hexadecyltrimethylammoium chloride(CTAC) on muscovite mica substrates was examined using atomic force microscopy(AFM). Adsorption morphology images and inte...The adsorption of dedecyltrimethylammoium chloride(DTAC) and hexadecyltrimethylammoium chloride(CTAC) on muscovite mica substrates was examined using atomic force microscopy(AFM). Adsorption morphology images and interaction forces of cationic surfactants at solid-solution interfaces were measured in tapping mode and Pico Force mode, respectively. The images demonstrated that the adsorbed structure was varied by a variety of surfactant concentrations. The adsorbed layer on mica was monolayer at first, and then became bilayer. A striped adsorbed structure was observed in a higher concentration of CTAC,which could not be found in any other concentrations of DTAC. For force measurements, the repulsive force was exponentially decreasing with the concentration increasing till a net attractive force appeared. A largest attractive force could be observed at a certain concentration, which was close to the point of charge neutralization. The results also showed a significant impact of hydrocarbon chain length on adsorption. An adsorption simulation was established to give a clear understanding of the interaction between cationic surfactants and mica.展开更多
This work presents a method for the three-dimensional localization of individual shallow NV center in diamond,leveraging the near-field quenching effect of a gold tip.Our experimental setup involves the use of an atom...This work presents a method for the three-dimensional localization of individual shallow NV center in diamond,leveraging the near-field quenching effect of a gold tip.Our experimental setup involves the use of an atomic force microscope to precisely move the gold tip close to the NV center,while simultaneously employing a home-made confocal microscope to monitor the fluorescence of the NV center.This approach allows for lateral super-resolution,achieving a full width at half maximum(FWHM)of 38.0 nm and a location uncertainty of 0.7 nm.Additionally,we show the potential of this method for determining the depth of the NV centers.We also attempt to determine the depth of the NV centers in combination with finite-difference time-domain(FDTD)simulations.Compared to other depth determination methods,this approach allows for simultaneous lateral and longitudinal localization of individual NV centers,and holds promise for facilitating manipulation of the local environment surrounding the NV center.展开更多
This paper deals with the assessment of vibro-acoustic properties of a multifunctional carbon fiber reinfo rced panel manu factured by bulk infu sion,a modified resin film infusion process.The components of the epoxy ...This paper deals with the assessment of vibro-acoustic properties of a multifunctional carbon fiber reinfo rced panel manu factured by bulk infu sion,a modified resin film infusion process.The components of the epoxy resin were chosen to contrast the electrical insulating property and poor flame resistance of the epoxy resins impregnating carbon woven fabric.To confer electrical conductivity to the resin a percentage of 0.5 wt%of Multi-Wall Carbon Nanotubes(MWCNTs)was dispersed in the resin,whereas to increase flame resistance a percentage of 5 wt%of Glycidil Polyhedral Oligomeric Silsesquioxanes(GPOSS)was solubilized in the epoxy mixture.Furthermore,as hardener agents,a mixture of 4,4’-DiaminoDiphenyl Sulfone(DDS)(53.4 wt%)and Bis(3-Aminophenyl)Methyl Phosphine Oxide(BAMPO)(46.7 wt%)was used.The values of the electrical conductivity were found satisfactory enough,being4.02×10^(-2)S/m for the multifunctional resin and 1.39×10^(4)S/m for the in-plane conductivity of the panel,whereas the Limiting Oxygen Index(LOI)value of the multifunctional resin was found to increase from 27%to 36%.Considering these promising results,an experimental assessment of the vibro-acoustic properties of the manufactured multifunctional panel was also performed.The panel was tested mainly to evaluate its low-frequency vibration damping and sound insulation characteristics.The manufactured panel demonstrated an improved efficiency if compared to a baseline configuration,presenting almost the double modal damping and a gain of 10 dB on the global noise reduction.展开更多
The separation of iron oxide from banded hematite jasper(BHJ) assaying 47.8% Fe, 25.6% Si O2 and 2.30%Al2O3 using selective magnetic coating was studied. Characterization studies of the low grade ore indicate that bes...The separation of iron oxide from banded hematite jasper(BHJ) assaying 47.8% Fe, 25.6% Si O2 and 2.30%Al2O3 using selective magnetic coating was studied. Characterization studies of the low grade ore indicate that besides hematite and goethite,jasper, a microcrystalline form of quartzite, is the major impurity associated with this ore. Beneficiation by conventional magnetic separation technique could yield a magnetic concentrate containing 60.8% Fe with 51% Fe recovery. In order to enhance the recovery of the iron oxide minerals, fine magnetite, colloidal magnetite and oleate colloidal magnetite were used as the coating material. When subjected to magnetic separation, the coated ore produces an iron concentrate containing 60.2% Fe with an enhanced recovery of56%. The AFM studies indicate that the coagulation of hematite particles with the oleate colloidal magnetite facilitates the higher recovery of iron particles from the low grade BHJ iron ore under appropriate conditions.展开更多
A novel modified Rayleigh model was developed for compensating hysteresis problem of an atomic force microscope(AFM) scanner.In high driving fields,piezoelectric actuators that integrated a scanner have severe hystere...A novel modified Rayleigh model was developed for compensating hysteresis problem of an atomic force microscope(AFM) scanner.In high driving fields,piezoelectric actuators that integrated a scanner have severe hysteresis,which can cause serious displacement errors.Piezoelectric hysteresis is from various origins including movement of defects,grain boundary effects,and displacement of interfaces.Furthermore,because its characteristic is stochastic,it is almost impossible to predict the piezoelectric hysteresis analytically.Therefore,it was predicted phenomenologically,which means that the relationship between inputs and outputs is formulated.The typical phenomenological approach is the Rayleigh model.However,the model has the discrepancy with experiment result as the fields increase.To overcome the demerit of the Rayleigh model,a modified Rayleigh model was proposed.In the modified Rayleigh model,each coefficient should be defined differently according to the field direction due to the increase of the asymmetry in the high fields.By applying an inverse form of this modified Rayleigh model to an AFM scanner,it is proved that hysteresis can be compensated to a position error of less than 5%.This model has the merits of reducing complicated fitting procedures and saving computation time compared with the Preisach model.展开更多
基金Project(50974134)supported by the National Natural Science Foundation of China
文摘The adsorption of dedecyltrimethylammoium chloride(DTAC) and hexadecyltrimethylammoium chloride(CTAC) on muscovite mica substrates was examined using atomic force microscopy(AFM). Adsorption morphology images and interaction forces of cationic surfactants at solid-solution interfaces were measured in tapping mode and Pico Force mode, respectively. The images demonstrated that the adsorbed structure was varied by a variety of surfactant concentrations. The adsorbed layer on mica was monolayer at first, and then became bilayer. A striped adsorbed structure was observed in a higher concentration of CTAC,which could not be found in any other concentrations of DTAC. For force measurements, the repulsive force was exponentially decreasing with the concentration increasing till a net attractive force appeared. A largest attractive force could be observed at a certain concentration, which was close to the point of charge neutralization. The results also showed a significant impact of hydrocarbon chain length on adsorption. An adsorption simulation was established to give a clear understanding of the interaction between cationic surfactants and mica.
基金supported by the National Natural Science Foundation of China(T2325023,92265204,12104447)the National Key R&D Program of China(2023YFF0718400)+1 种基金the Innovation Program for Quantum Science and Technology(2021ZD0302200)the Fundamental Research Funds for the Central Universities。
文摘This work presents a method for the three-dimensional localization of individual shallow NV center in diamond,leveraging the near-field quenching effect of a gold tip.Our experimental setup involves the use of an atomic force microscope to precisely move the gold tip close to the NV center,while simultaneously employing a home-made confocal microscope to monitor the fluorescence of the NV center.This approach allows for lateral super-resolution,achieving a full width at half maximum(FWHM)of 38.0 nm and a location uncertainty of 0.7 nm.Additionally,we show the potential of this method for determining the depth of the NV centers.We also attempt to determine the depth of the NV centers in combination with finite-difference time-domain(FDTD)simulations.Compared to other depth determination methods,this approach allows for simultaneous lateral and longitudinal localization of individual NV centers,and holds promise for facilitating manipulation of the local environment surrounding the NV center.
文摘This paper deals with the assessment of vibro-acoustic properties of a multifunctional carbon fiber reinfo rced panel manu factured by bulk infu sion,a modified resin film infusion process.The components of the epoxy resin were chosen to contrast the electrical insulating property and poor flame resistance of the epoxy resins impregnating carbon woven fabric.To confer electrical conductivity to the resin a percentage of 0.5 wt%of Multi-Wall Carbon Nanotubes(MWCNTs)was dispersed in the resin,whereas to increase flame resistance a percentage of 5 wt%of Glycidil Polyhedral Oligomeric Silsesquioxanes(GPOSS)was solubilized in the epoxy mixture.Furthermore,as hardener agents,a mixture of 4,4’-DiaminoDiphenyl Sulfone(DDS)(53.4 wt%)and Bis(3-Aminophenyl)Methyl Phosphine Oxide(BAMPO)(46.7 wt%)was used.The values of the electrical conductivity were found satisfactory enough,being4.02×10^(-2)S/m for the multifunctional resin and 1.39×10^(4)S/m for the in-plane conductivity of the panel,whereas the Limiting Oxygen Index(LOI)value of the multifunctional resin was found to increase from 27%to 36%.Considering these promising results,an experimental assessment of the vibro-acoustic properties of the manufactured multifunctional panel was also performed.The panel was tested mainly to evaluate its low-frequency vibration damping and sound insulation characteristics.The manufactured panel demonstrated an improved efficiency if compared to a baseline configuration,presenting almost the double modal damping and a gain of 10 dB on the global noise reduction.
文摘The separation of iron oxide from banded hematite jasper(BHJ) assaying 47.8% Fe, 25.6% Si O2 and 2.30%Al2O3 using selective magnetic coating was studied. Characterization studies of the low grade ore indicate that besides hematite and goethite,jasper, a microcrystalline form of quartzite, is the major impurity associated with this ore. Beneficiation by conventional magnetic separation technique could yield a magnetic concentrate containing 60.8% Fe with 51% Fe recovery. In order to enhance the recovery of the iron oxide minerals, fine magnetite, colloidal magnetite and oleate colloidal magnetite were used as the coating material. When subjected to magnetic separation, the coated ore produces an iron concentrate containing 60.2% Fe with an enhanced recovery of56%. The AFM studies indicate that the coagulation of hematite particles with the oleate colloidal magnetite facilitates the higher recovery of iron particles from the low grade BHJ iron ore under appropriate conditions.
基金Project supported by the Second Stage of Brain Korea 21 ProjectProject supported by the Korea Science and Engineering Foundation (KOSEF) through the National Research Laboratory Program Funded by the Ministry of Science and TechnologyProject supported by Changwon National University,Korea
文摘A novel modified Rayleigh model was developed for compensating hysteresis problem of an atomic force microscope(AFM) scanner.In high driving fields,piezoelectric actuators that integrated a scanner have severe hysteresis,which can cause serious displacement errors.Piezoelectric hysteresis is from various origins including movement of defects,grain boundary effects,and displacement of interfaces.Furthermore,because its characteristic is stochastic,it is almost impossible to predict the piezoelectric hysteresis analytically.Therefore,it was predicted phenomenologically,which means that the relationship between inputs and outputs is formulated.The typical phenomenological approach is the Rayleigh model.However,the model has the discrepancy with experiment result as the fields increase.To overcome the demerit of the Rayleigh model,a modified Rayleigh model was proposed.In the modified Rayleigh model,each coefficient should be defined differently according to the field direction due to the increase of the asymmetry in the high fields.By applying an inverse form of this modified Rayleigh model to an AFM scanner,it is proved that hysteresis can be compensated to a position error of less than 5%.This model has the merits of reducing complicated fitting procedures and saving computation time compared with the Preisach model.
