The stress corrosion crack （SCC） susceptibility of ultra-high strength steel AerMet 100 was investigated by slow strain rate technique （SSRT）, tensile with polarization and surface analysis technique. The curves o...The stress corrosion crack （SCC） susceptibility of ultra-high strength steel AerMet 100 was investigated by slow strain rate technique （SSRT）, tensile with polarization and surface analysis technique. The curves of tf^Cl/tf^W -strain rate are divided into three regions： stress-dominated region, SCC-dominated region, and corrosion-dominated region, so as the curves of εf^Cl/εf^W - strain rate and tm/tf-strain rate. The results of tensile tests with polarization show that the main SCC mechanism of AerMet 100 is anodic dissolution, which controls the corrosion process. The three regions have been discussed according to the relationship between the rate of slip-step formation and the rate of dissolution. Fracture appearances in different environments were analyzed by scanning electron microscopy （SEM）. SCC fracture appears as a mixture of intergranular and dimples, while it is totally dimples in the inert environment. The εf becomes the parameter to predict tf because the relationship between εf^Cl/εf^W and tf^Cl/tf^w is a straight line for AerMet 100.展开更多
Mg-6%Al-1%Sn(mass fraction) alloy is a newly developed anode material for seawater activated batteries. The electrochemical properties of Mg-1%Sn, Mg-6%Al and Mg-6%Al-1%Sn alloys are measured by galvanostatic and pote...Mg-6%Al-1%Sn(mass fraction) alloy is a newly developed anode material for seawater activated batteries. The electrochemical properties of Mg-1%Sn, Mg-6%Al and Mg-6%Al-1%Sn alloys are measured by galvanostatic and potentiodynamic tests. Scanning electron microscopy(SEM) with energy dispersive spectrometry(EDS) is used to characterize the microstructures of the experimental alloys. The results show that the Mg-6%Al-1%Sn alloy obtains more negative discharge potential(-1.38 V(vs SCE)) in hot-rolled condition. This is attributed to the fine dynamically recrystallized grains during the hot rolling process. After the experimental alloys are annealed at 473 K for 1 h, the discharge potentials of Mg-6%Al-1%Sn alloy are more negative than those of Mg-6%Al alloy under different current densities. After annealing at 673 K, the discharge potentials of Mg-6%Al-1%Sn alloy become more positive than those of Mg-6%Al alloy. Such phenomenon is due to the coarse grains and the second phase Mg2 Sn. The discharge potentials of Mg-1%Sn shift positively obviously in the discharge process compared with Mg-6%Al-1%Sn alloy. This is due to the corrosion products pasting on the discharge surface, which leads to anode polarization.展开更多
基金Project(51171011) supported by the National Natural Science Foundation of China
文摘The stress corrosion crack （SCC） susceptibility of ultra-high strength steel AerMet 100 was investigated by slow strain rate technique （SSRT）, tensile with polarization and surface analysis technique. The curves of tf^Cl/tf^W -strain rate are divided into three regions： stress-dominated region, SCC-dominated region, and corrosion-dominated region, so as the curves of εf^Cl/εf^W - strain rate and tm/tf-strain rate. The results of tensile tests with polarization show that the main SCC mechanism of AerMet 100 is anodic dissolution, which controls the corrosion process. The three regions have been discussed according to the relationship between the rate of slip-step formation and the rate of dissolution. Fracture appearances in different environments were analyzed by scanning electron microscopy （SEM）. SCC fracture appears as a mixture of intergranular and dimples, while it is totally dimples in the inert environment. The εf becomes the parameter to predict tf because the relationship between εf^Cl/εf^W and tf^Cl/tf^w is a straight line for AerMet 100.
基金supported by the Open Fund of the Sate Key Laboratory of Powder Metallurgy(Central South University),China
文摘Mg-6%Al-1%Sn(mass fraction) alloy is a newly developed anode material for seawater activated batteries. The electrochemical properties of Mg-1%Sn, Mg-6%Al and Mg-6%Al-1%Sn alloys are measured by galvanostatic and potentiodynamic tests. Scanning electron microscopy(SEM) with energy dispersive spectrometry(EDS) is used to characterize the microstructures of the experimental alloys. The results show that the Mg-6%Al-1%Sn alloy obtains more negative discharge potential(-1.38 V(vs SCE)) in hot-rolled condition. This is attributed to the fine dynamically recrystallized grains during the hot rolling process. After the experimental alloys are annealed at 473 K for 1 h, the discharge potentials of Mg-6%Al-1%Sn alloy are more negative than those of Mg-6%Al alloy under different current densities. After annealing at 673 K, the discharge potentials of Mg-6%Al-1%Sn alloy become more positive than those of Mg-6%Al alloy. Such phenomenon is due to the coarse grains and the second phase Mg2 Sn. The discharge potentials of Mg-1%Sn shift positively obviously in the discharge process compared with Mg-6%Al-1%Sn alloy. This is due to the corrosion products pasting on the discharge surface, which leads to anode polarization.
