In order to improve the speed and accuracy of analog circuit fault diagnosis,using Back Propagation Neural Network(BPNN),a new method is proposed based on Particle Swarm Optimization(PSO)to adjust weights of BP neural...In order to improve the speed and accuracy of analog circuit fault diagnosis,using Back Propagation Neural Network(BPNN),a new method is proposed based on Particle Swarm Optimization(PSO)to adjust weights of BP neural network.The model can not only overcome the limitations of the slow convergence and the local extreme values by basic BP algorithm,but also improve the learning ability and generalization ability with a higher precision.The response signals of analog circuit is preprocessed by Wavelet Packet Transform(WPT)as the fault feature.The simulation result shows that the proposed method has higher diagnostic accuracy and faster convergence speed,which is effective for fault location.展开更多
The soft fault induced by parameter variation is one of the most challenging problems in the domain of fault diagnosis for analog circuits.A new fault location and parameter prediction approach for soft-faults diagnos...The soft fault induced by parameter variation is one of the most challenging problems in the domain of fault diagnosis for analog circuits.A new fault location and parameter prediction approach for soft-faults diagnosis in analog circuits is presented in this paper.The proposed method extracts the original signals from the output terminals of the circuits under test（CUT） by a data acquisition board.Firstly,the phase deviation value between fault-free and faulty conditions is obtained by fitting the sampling sequence with a sine curve.Secondly,the sampling sequence is organized into a square matrix and the spectral radius of this matrix is obtained.Thirdly,the smallest error of the spectral radius and the corresponding component value are obtained through comparing the spectral radius and phase deviation value with the trend curves of them,respectively,which are calculated from the simulation data.Finally,the fault location is completed by using the smallest error,and the corresponding component value is the parameter identification result.Both simulated and experimental results show the effectiveness of the proposed approach.It is particularly suitable for the fault location and parameter identification for analog integrated circuits.展开更多
A single soft fault diagnosis method for analog circuit with tolerance based on particle swarm optimization （PSO） is proposed. The parameter deviation of circuit elements is defined as the element of particle. Node-...A single soft fault diagnosis method for analog circuit with tolerance based on particle swarm optimization （PSO） is proposed. The parameter deviation of circuit elements is defined as the element of particle. Node-voltage incremental equations based on the sensitivity analysis are built as constraints of a linear programming （LP） equation. Through inducing the penalty coefficient, the LP equation is set as the fitness function for the PSO program. After evaluating the best position of particles, the position of the optimal particle states whether the actual parameter is within tolerance range or not. Simulation result shows the effectiveness of the method.展开更多
In this paper, it is proved that the direction of the node-voltage difference vector, which is the difference between the node-voltage vector at faulty state and the one at the nominal state, is determined only by the...In this paper, it is proved that the direction of the node-voltage difference vector, which is the difference between the node-voltage vector at faulty state and the one at the nominal state, is determined only by the location of the faulty clement in linear analog circuits. Considering that the direction of the node-voltage sensitivity vector is the same as the one of the node-voltage difference vector and also considering that the module of the node-voltage sensitivity vector presents the weight of the parameter of faulty element deviation relative to the voltage difference, fault dictionary is set up based on node-voltage sensitivity vectors. A decision algorithm is proposed concerned with both the location and the parameter difference of the faulty element. Single fault and multi-fault can be diagnosed while the circuit parameters deviate within the tolerance range of 10 %.展开更多
A binary tree representation is designed in this paper for optimization of wave digital filter（WDF）implementation.To achieve this,an equivalent WDF model of the original circuit is converted into abinary tree repres...A binary tree representation is designed in this paper for optimization of wave digital filter（WDF）implementation.To achieve this,an equivalent WDF model of the original circuit is converted into abinary tree representation at first.This WDF binary tree can then be transformed to several topologies with the same implication,since the WDF adaptors have a symmetrical behavior on their ports.Because the WDF implementation is related to field programmable gate array（FPGA）resource usage and the cycle time of emulation,choosing aproper binary tree topology for WDF implementation can help balance the complexity and performance quality of an emulation system.Both WDF-FPGA emulation and HSpice simulation on the same circuit are tested.There is no significant difference between these two simulations.However,in terms of time consumption,the WDF-FPGA emulation has an advantage over the other.Our experiment also demonstrates that the optimized WDF-FPGA emulation has an acceptable accuracy and feasibility.展开更多
Using fuzzy C cluster mean (FCM), fuzzy theory and neural network, a fault diagnosis method was proposed, which was based on fuzzy C-means clustering algorithm of neural network that was applied in non-linear analog c...Using fuzzy C cluster mean (FCM), fuzzy theory and neural network, a fault diagnosis method was proposed, which was based on fuzzy C-means clustering algorithm of neural network that was applied in non-linear analog circuits and in diagnoses the ARNIC 429 reception circuit of aviation aircraft avionics. The C cluster algorithm can make the amount of the fuzzy rule automatically and can create an initial fuzzy rule database of fault diagnosis. A type of fuzzy neural network and a fault tree were generated. The algorithm avoids the disadvantage that gets into the part of optimum circumstance. A validate application was implemented, which proves that the method is effective. Therefore, the method is superior to the traditional methods in fault diagnosis, and the efficiency is heavily improved.展开更多
为标定光交叉芯片驱动电压,控制光交叉芯片实现光路由功能,提出并搭建了基于多通道DAC(Digital to Analog Converter)阵列的控制驱动电路系统。系统主要由控制系统模块、多路驱动电路模块及上位机控制模块构成。控制电路和驱动电路具有...为标定光交叉芯片驱动电压,控制光交叉芯片实现光路由功能,提出并搭建了基于多通道DAC(Digital to Analog Converter)阵列的控制驱动电路系统。系统主要由控制系统模块、多路驱动电路模块及上位机控制模块构成。控制电路和驱动电路具有调校简单、可双极性输出、输出路数多、加电精确度较高的特点,解决了当前驱动电路工作繁琐、加电极性单一、加电路数少、精度差的问题。上位机控制模块除了可控制驱动电路施加控制电压外,还可接收来自数据采集装置采集到的光功率信号作为控制驱动系统的反馈信号。通过分析控制电压与光功率之间的关系,可得到最佳的光交叉芯片控制驱动电压。系统测试实验结果表明,该系统能提供高精确度的双极性驱动电压,有效地对光交叉芯片进行驱动。可在较短的时间内标定出光开关的控制电压,完全可以满足有源光交叉芯片控制中对驱动电压的需求。该系统在光交叉芯片控制方面具有一定的应用价值。展开更多
基金supported the Science and Technology Research Project of Liaoning Provincial Department of Education
文摘In order to improve the speed and accuracy of analog circuit fault diagnosis,using Back Propagation Neural Network(BPNN),a new method is proposed based on Particle Swarm Optimization(PSO)to adjust weights of BP neural network.The model can not only overcome the limitations of the slow convergence and the local extreme values by basic BP algorithm,but also improve the learning ability and generalization ability with a higher precision.The response signals of analog circuit is preprocessed by Wavelet Packet Transform(WPT)as the fault feature.The simulation result shows that the proposed method has higher diagnostic accuracy and faster convergence speed,which is effective for fault location.
基金supported by the National Natural Science Foundation of China under Grant No.61371049
文摘The soft fault induced by parameter variation is one of the most challenging problems in the domain of fault diagnosis for analog circuits.A new fault location and parameter prediction approach for soft-faults diagnosis in analog circuits is presented in this paper.The proposed method extracts the original signals from the output terminals of the circuits under test（CUT） by a data acquisition board.Firstly,the phase deviation value between fault-free and faulty conditions is obtained by fitting the sampling sequence with a sine curve.Secondly,the sampling sequence is organized into a square matrix and the spectral radius of this matrix is obtained.Thirdly,the smallest error of the spectral radius and the corresponding component value are obtained through comparing the spectral radius and phase deviation value with the trend curves of them,respectively,which are calculated from the simulation data.Finally,the fault location is completed by using the smallest error,and the corresponding component value is the parameter identification result.Both simulated and experimental results show the effectiveness of the proposed approach.It is particularly suitable for the fault location and parameter identification for analog integrated circuits.
基金supported by the Program for New Century Excellent Talents in University under Grant No.NCET-05-0804partly supported by Chinese National Programs for High Technology Research and Development under Grant No.2006AA06Z222
文摘A single soft fault diagnosis method for analog circuit with tolerance based on particle swarm optimization （PSO） is proposed. The parameter deviation of circuit elements is defined as the element of particle. Node-voltage incremental equations based on the sensitivity analysis are built as constraints of a linear programming （LP） equation. Through inducing the penalty coefficient, the LP equation is set as the fitness function for the PSO program. After evaluating the best position of particles, the position of the optimal particle states whether the actual parameter is within tolerance range or not. Simulation result shows the effectiveness of the method.
基金supported by Program for New Century Excellent Talents in University under Grant No.NCET-05-0804
文摘In this paper, it is proved that the direction of the node-voltage difference vector, which is the difference between the node-voltage vector at faulty state and the one at the nominal state, is determined only by the location of the faulty clement in linear analog circuits. Considering that the direction of the node-voltage sensitivity vector is the same as the one of the node-voltage difference vector and also considering that the module of the node-voltage sensitivity vector presents the weight of the parameter of faulty element deviation relative to the voltage difference, fault dictionary is set up based on node-voltage sensitivity vectors. A decision algorithm is proposed concerned with both the location and the parameter difference of the faulty element. Single fault and multi-fault can be diagnosed while the circuit parameters deviate within the tolerance range of 10 %.
基金Supported by the National Natural Science Foundation of China(61271113)
文摘A binary tree representation is designed in this paper for optimization of wave digital filter（WDF）implementation.To achieve this,an equivalent WDF model of the original circuit is converted into abinary tree representation at first.This WDF binary tree can then be transformed to several topologies with the same implication,since the WDF adaptors have a symmetrical behavior on their ports.Because the WDF implementation is related to field programmable gate array（FPGA）resource usage and the cycle time of emulation,choosing aproper binary tree topology for WDF implementation can help balance the complexity and performance quality of an emulation system.Both WDF-FPGA emulation and HSpice simulation on the same circuit are tested.There is no significant difference between these two simulations.However,in terms of time consumption,the WDF-FPGA emulation has an advantage over the other.Our experiment also demonstrates that the optimized WDF-FPGA emulation has an acceptable accuracy and feasibility.
基金Project (MHRD0705) supported by the Science Foundation by Civil Aviation Administrator of ChinaProject (07ZCKFGX01500) supported by Tianjin Science Foundation and Technology Key Project
文摘Using fuzzy C cluster mean (FCM), fuzzy theory and neural network, a fault diagnosis method was proposed, which was based on fuzzy C-means clustering algorithm of neural network that was applied in non-linear analog circuits and in diagnoses the ARNIC 429 reception circuit of aviation aircraft avionics. The C cluster algorithm can make the amount of the fuzzy rule automatically and can create an initial fuzzy rule database of fault diagnosis. A type of fuzzy neural network and a fault tree were generated. The algorithm avoids the disadvantage that gets into the part of optimum circumstance. A validate application was implemented, which proves that the method is effective. Therefore, the method is superior to the traditional methods in fault diagnosis, and the efficiency is heavily improved.
文摘为标定光交叉芯片驱动电压,控制光交叉芯片实现光路由功能,提出并搭建了基于多通道DAC(Digital to Analog Converter)阵列的控制驱动电路系统。系统主要由控制系统模块、多路驱动电路模块及上位机控制模块构成。控制电路和驱动电路具有调校简单、可双极性输出、输出路数多、加电精确度较高的特点,解决了当前驱动电路工作繁琐、加电极性单一、加电路数少、精度差的问题。上位机控制模块除了可控制驱动电路施加控制电压外,还可接收来自数据采集装置采集到的光功率信号作为控制驱动系统的反馈信号。通过分析控制电压与光功率之间的关系,可得到最佳的光交叉芯片控制驱动电压。系统测试实验结果表明,该系统能提供高精确度的双极性驱动电压,有效地对光交叉芯片进行驱动。可在较短的时间内标定出光开关的控制电压,完全可以满足有源光交叉芯片控制中对驱动电压的需求。该系统在光交叉芯片控制方面具有一定的应用价值。
