Improving interfacial bonding and alloying design are effective strategies for enhancing mechanical properties of particle-reinforced steel matrix composites(SMCs).This study prepared SMCs with uniformly distributed T...Improving interfacial bonding and alloying design are effective strategies for enhancing mechanical properties of particle-reinforced steel matrix composites(SMCs).This study prepared SMCs with uniformly distributed TiC_(P)in matrix using master alloying method.The TiC(002)/Fe(011)interface model was established based on the orientation relationship of(011)_(Fe)//(002)_(TiC),and[100]_(Fe)//[100]_(TiC).The effects of single and co-doping of alloying elements(Mn,Cr,Mo,Ni,Cu and Si)on the interface bonding behavior of TiC/Fe in composites were investigated in conjunction with first principles.The results demonstrate that the interface between TiC and matrix is continuous and stable.Compared to the undoped TiC/Fe interface,single-doping Mn,Cr,and Mo can improve the stability of TiC/Fe interface and enhance tensile strength.Conversely,single-doping with Ni,Cu,and Si reduced the interface stability and marginally reduces tensile strength.Relative to the undoped and singly Ni-doped TiC/Fe interfaces,the co-doping Ni-Mo boosts binding energy and separation work at the TiC/Fe interface,which is conducive to the interface bonding between TiC_(P)and matrix,and thus improves the mechanical properties of composites.Thus,in the alloying design of TiC particle reinforced low-alloy SMCs,incorporating Mn,Cr,Mo,and Ni into matrix can enhance the overall mechanical properties of composites.展开更多
The effects of Yb/Zr micro-alloying on the microstructure,mechanical properties,and corrosion resistance of an Al-Zn-Mg-Cu alloy were systematically investigated.Upon the addition of Yb/Zr to the Al-Zn-Mg-Cu alloy,the...The effects of Yb/Zr micro-alloying on the microstructure,mechanical properties,and corrosion resistance of an Al-Zn-Mg-Cu alloy were systematically investigated.Upon the addition of Yb/Zr to the Al-Zn-Mg-Cu alloy,the grain boundaries were pinned by high-density nanosized Al_(3)(Yb,Zr)precipitates during extrusion deformation,consequently,the average grain size was significantly reduced from 232.7μm to 3.2μm.This grain refinement contributed substantially to the improvement in both strength and elongation.The ultimate tensile strength,yield strength,and elongation of the Yb/Zr modified alloy increased to 705.3 MPa,677.6 MPa,and 8.7%,respectively,representing enhancements of 16.2%,19.3%,and 112.2%compared to the unmodified alloy.Moreover,the distribution of MgZn_(2)phases along grain boundaries became more discontinuous in the Yb/Zr modified alloy,which effectively retarded the propagation of intergranular corrosion and improved the corrosion resistance.展开更多
The cooperative effect of laser surface texturing(LST) and double glow plasma surface alloying on tribological performance of lubricated sliding contacts was investigated.A Nd:YAG laser was used to generate microdimpl...The cooperative effect of laser surface texturing(LST) and double glow plasma surface alloying on tribological performance of lubricated sliding contacts was investigated.A Nd:YAG laser was used to generate microdimples on steel surfaces. Dimples with the diameter of 150μm and the depth of 30-35μm distributed circumferentially on the disc surface.The alloying element Cr was sputtered to the laser texturing steel surface by double glow plasma technique.A deep diffusion layer with a thickness of 30μm and a high hardness of HV900 was formed in this alloy.Tribological experiments of three types of samples(smooth,texturing and texturing+alloying) were conducted with a ring-on-disc tribometer to simulate the face seal.It is found that,in comparison with smooth steel surfaces,the laser texturing samples significantly reduce the friction coefficient.Moreover,the lower wear rate of the sample treated with the two surface techniques is observed.展开更多
The slow degration of iron limits its bone implant application.The solid solution of Zn in Fe is expected to accelerate the degradation.In this work,mechanical alloying(MA)was used to prepare Fe-Zn powder with supersa...The slow degration of iron limits its bone implant application.The solid solution of Zn in Fe is expected to accelerate the degradation.In this work,mechanical alloying(MA)was used to prepare Fe-Zn powder with supersaturated solid solution.MA significantly decreased the lamellar spacing between particles,thus reducing the diffusion distance of solution atoms.Moreover,it caused a number of crystalline defects,which further promoted the solution diffusion.Subsequently,the MA-processed powder was consolidated into Fe-Zn part by laser sintering,which involved a partial melting/rapid solidification mechanism and retained the original supersaturated solid solution.Results proved that the Fe-Zn alloy became more susceptible with a lowered corrosion potential,and thereby an accelerated corrosion rate of(0.112±0.013)mm/year.Furthermore,it also exhibited favorable cell behavior.This work highlighted the advantage of MA combined with laser sintering for the preparation of Fe-Zn implant with improved degradation performance.展开更多
Mg-Zn binary alloys fabricated by the gas-phase alloying technique under vacuum condition were investigated in the state of initial state and after heat treatment for the microstructure and electrochemical behaviors.D...Mg-Zn binary alloys fabricated by the gas-phase alloying technique under vacuum condition were investigated in the state of initial state and after heat treatment for the microstructure and electrochemical behaviors.Different from the traditional Mg-Zn alloys preparation methods,alloys prepared by gas-phase alloying have a large number of intermetallic compounds,such as MgZn,Mg7Zn3 and MgZn2.After solution treatment,the boundary of the eutectic disappeared and the size ofα-Mg increased from 100μm to 150μm.At the same time,the value of the resistance of charge transfer increased,which indicates that the resistance of the charge transfer and the corrosion resistance of the alloys increased.After artificial aging treatment,the distribution ofα-Mg was more uniform and its size was reduced to about 50μm,and there was new eutectic structure formed.The newly formed eutectic structure forms galvanic cells with the alloy matrix,which makes the corrosion resistance of the alloy weaken.展开更多
The alloying effects of V on structural,elastic and electronic properties of TiFe_2 phase were investigated by the first-principles calculations based on the density functional theory.The calculated energy properties ...The alloying effects of V on structural,elastic and electronic properties of TiFe_2 phase were investigated by the first-principles calculations based on the density functional theory.The calculated energy properties including cohesive energy and formation enthalpy indicate V atom would preferentially substitute on 6h sites of Fe atoms in the lattice of TiFe_2 to form the intermetallic Ti_4Fe_7(V).The calculated results of polycrystalline elastic parameters confirm that the plasticity of TiFe_2 would be improved with the addition of V.By discussing the percentage of elastic anisotropy,anisotropy in linear bulk modulus and directional dependence of elastic modulus,it is revealed that the anisotropy of TiFe_2 and Ti_4Fe_7(V) is small.Finally,the density of states,charge density distribution and Mulliken population for TiFe_2 and Ti_4Fe_7(V) were calculated,suggesting there is a mixed bonding with metallic,covalent and ionic nature in TiFe_2 and Ti_4Fe_7(V) compounds.These results also clarify that the reason for the improvement of plasticity with the addition of V in TiFe_2 is the weakened bonding of covalent feature between Ti and V atoms.展开更多
Zr50Al15Ni10Cu25 amorphous powder was synthesized by mechanical alloying. The effect of Si3N4 addition on the crystallization behavior of the alloy during sintering process was studied. Thermal stability of the powder...Zr50Al15Ni10Cu25 amorphous powder was synthesized by mechanical alloying. The effect of Si3N4 addition on the crystallization behavior of the alloy during sintering process was studied. Thermal stability of the powders was performed by differential scanning calorimetry （DSC）. The phase and microstructure of the powders and bulk specimens sintered were determined by X-ray diffractometry （XRD） and scanning electron microscopy （SEM）. The results show that, introducing 0.05% （mass fraction） Si3N4 can enhance the crystallization activation energy of the ZZr50Al15Ni10Cu25 amorphous powders, which indicates that Si3N4 addition has hindrance effect on forming crystals from Zr50Al15Ni10Cu25amorphous powder. However, 0.10% Si3N4 results in the decrease of the crystallization activation energy, which makes its crystallization process easy to occur.展开更多
The mechanical properties of calcium(Ca) microalloyed 24 carat gold(Au 99.9 Ca 0.1) were measured and the corresponding microstructure was observed by TEM in order to investigate the strengthening mechanism.It was obs...The mechanical properties of calcium(Ca) microalloyed 24 carat gold(Au 99.9 Ca 0.1) were measured and the corresponding microstructure was observed by TEM in order to investigate the strengthening mechanism.It was observed that the microalloying of 0.1wt% Ca improved the tensile strength(by 79% and 57% for the rolling and annealing states,respectively),hardness and E-Modulus as well as reduced the ductility of the 24 carat Au.Dispersed nano-sized precipitates and high density deformation twins were found in the rolled Au 99.9 Ca 0.1,which are attributed to be the major strengthening factors.The twins subsided after annealing and the strengthening of the annealed Au 99.9 Ca 0.1 is mainly contributed by the coarsened semi-coherent precipitates.展开更多
As an essential candidate for environment-friendly luminescent quantum dots(QDs),CuInS-based QDs have attracted more attention in recent years.However,several drawbacks still hamper their industrial applications,such ...As an essential candidate for environment-friendly luminescent quantum dots(QDs),CuInS-based QDs have attracted more attention in recent years.However,several drawbacks still hamper their industrial applications,such as lower photoluminescence quantum yield(PLQY),complex synthetic pathways,uncontrollable emission spectra,and insufficient photostability.In this study,CuInZnS@ZnS core/shell QDs was prepared via a one-pot/three-step synthetic scheme with accurate and tunable control of PL spectra.Then their ensemble spectroscopic properties during nucleation formation,alloying,and ZnS shell growth processes were systematically investigated.PL peaks of these QDs can be precisely manipulated from 530 to 850 nm by controlling the stoichiometric ratio of Cu/In,Zn^(2+)doping and ZnS shell growth.In particular,CuInZnS@ZnS QDs possess a significantly long emission lifetime(up to 750 ns),high PLQY(up to 85%),and excellent crystallinity.Their spectroscopic evolution is well validated by Cu-deficient related intragap emission model.By controlling the stoichiometric ratio of Cu/In,two distinct Cu-deficient related emission pathways are established based on the differing oxidation states of Cu defects.Therefore,this work provides deeper insights for fabricating high luminescent ternary or quaternary-alloyed QDs.展开更多
Titanium alloy has the advantages of high strength,strong corrosion resistance,excellent high and low temperature mechanical properties,etc.,and is widely used in aerospace,shipbuilding,weapons and equipment,and other...Titanium alloy has the advantages of high strength,strong corrosion resistance,excellent high and low temperature mechanical properties,etc.,and is widely used in aerospace,shipbuilding,weapons and equipment,and other fields.In recent years,with the continuous increase in demand for medium-thick plate titanium alloys,corresponding welding technologies have also continued to develop.Therefore,this article reviews the research progress of deep penetration welding technology for medium-thick plate titanium alloys,mainly covering traditional arc welding,high-energy beam welding,and other welding technologies.Among many methods,narrow gap welding,hybrid welding,and external energy field assistance welding all contribute to improving the welding efficiency and quality of medium-thick plate titanium alloys.Finally,the development trend of deep penetration welding technology for mediumthick plate titanium alloys is prospected.展开更多
As an efficient passive anti-icing method,the superhydrophobic surface can reduce icing process on metals in low temperatures.However,the usual organic low-surface-energy decorations are often prone to age especially ...As an efficient passive anti-icing method,the superhydrophobic surface can reduce icing process on metals in low temperatures.However,the usual organic low-surface-energy decorations are often prone to age especially in harsh environments,leading to a decrease or complete failure of the anti-icing performance.Here,we adopt a fabrication method of femtosecond laser element-doping microstructuring to achieve inor-ganic superhydrophobic aluminum alloys surfaces through simultaneously modifying the surface profile and compositions of aluminum alloys.The obtained bionic anthill tribe structure with the low thermal conductiv-ity,exhibits the superior delayed freezing time(803.3 s)and the low ice adhesion(16μN)in comparison to the fluorosilane modified and bare Al surfaces.Moreover,such an inherently superhydrophobic metal sur-face also shows the exceptional environmental durability in anti-icing performance,which confirms the ef-fectiveness of our superhydrophobic surface without the need for organic coatings.展开更多
The effects of different warm rolling(WR)reductions on the microstructure and mechanical properties of low-Cr FeCrAl alloys at both room and elevated temperatures were investigated.The study revealed that when the WR ...The effects of different warm rolling(WR)reductions on the microstructure and mechanical properties of low-Cr FeCrAl alloys at both room and elevated temperatures were investigated.The study revealed that when the WR reduction is small,it effectively refines the grains and forms a large number of subgrains in the matrix,while also inducing the dissolution of the Laves phase.This enhances the mechanical properties of FeCrAl alloys primarily through grain refinement and solid solution strengthening.Conversely,with larger WR reductions,the grain refinement effect diminishes,but a significant number of Laves phases form in the matrix,strengthening the alloys primarily through precipitation strengthening.WR exhibited a remarkable enhancing effect on the comprehensive mechanical properties at both room and high temperatures,with a signi-ficant enhancement in ductility at high temperatures.Notably,a 10%WR reduction resulted in the optimal overall mechanical properties at both room and elevated temperatures.展开更多
Zirconium alloy(Zr-4)is extensively utilized in nuclear fuel cladding materials due to its exceptional neutron economy,high ductility,and promising corrosion and irradiation resistance.Nevertheless,during the operatio...Zirconium alloy(Zr-4)is extensively utilized in nuclear fuel cladding materials due to its exceptional neutron economy,high ductility,and promising corrosion and irradiation resistance.Nevertheless,during the operational lifespan of the Zr-4 fuel tube,micro-oscillations induced by the high-speed flow of cooling water can cause wear between the cladding tube and grids.This leads to wear failure of the Zr-4 alloy tube,which seriously threatens the safe operation of nuclear stations.The application of protective coatings onto the surface of zirconium alloys serves to enhance their resistance against wear,while without changing of the existing reactor structure.In this study,FeCrAl/CrN and FeCrAl coatings were fabricated on the surface of Zr-4 alloy using dual-target co-sputtering technology.The effects of the CrN interlayer on the microstructure,mechanical properties,and tribological behavior of FeCrAl coating in air and B-Li water were investigated,and a comparative analysis with Zr-4 alloy was conducted.The results showed that the application of FeCrAl/CrN and FeCrAl coatings significantly enhanced the hardness and wear resistance of Zr-4 alloy.The introduction of the CrN interlayer increased the columnar grain size of the FeCrAl coating and caused a change in the preferred growth direction of the coating from(110)to(211).The CrN interlayer improved the hardness and wear resistance of the coating,it also led to a decrease in adhesion strength.The wear rates of FeCrAl/CrN coatings in air and B-Li water were the lowest,about 3.2×10^(-6) mm^(3)/(N·m)and 6.0×10^(-7) mm^(3)/(N·m),respectively.The lubricating effect of B-Li water effectively reduced the friction coefficient and wear rate of both FeCrAl/CrN and FeCrAl coatings.In air and B-Li water,the primary wear mechanisms for Zr-4 are adhesive wear and oxidative wear,while the main wear mechanisms for FeCrAl/CrN and FeCrAl coatings are abrasive wear and oxidative wear.These findings not only provided a theoretical basis for understanding the microstructure and wear performance of FeCrAl coatings but also offered important technical guidance for their practical application in the nuclear industry.展开更多
Metal-organic frameworks(MOFs)are import-ant as possible energy storage materials.Nitrogen-doped iron-cobalt MOFs were synthesized by a one-pot solvo-thermal method using CoCl_(3)·6H_(2)O and FeCl_(3)·6H_(2)...Metal-organic frameworks(MOFs)are import-ant as possible energy storage materials.Nitrogen-doped iron-cobalt MOFs were synthesized by a one-pot solvo-thermal method using CoCl_(3)·6H_(2)O and FeCl_(3)·6H_(2)O dis-solved in N,N-dimethylformamide,and were converted into Fe-Co embedded in N-doped porous carbon polyhedra by pyrolysis in a nitrogen atmosphere.During pyrolysis,the or-ganic ligands transformed into N-doped porous carbon which improved their structural stability and also their electrical contact with other materials.The Fe and Co are tightly bound together because of their encapsulation by the carbon nitride and are well dispersed in the carbon matrix,and improve the material’s conductivity and stability and provide additional capacity.When used as the anode for lithium-ion batteries,the material gives an initial capacity of up to 2230.7 mAh g^(-1)and a reversible capa-city of 1146.3 mAh g^(-1)is retained after 500 cycles at a current density of 0.5 A g^(-1),making it an excellent candidate for this purpose.展开更多
High-Entropy Alloys(HEAs)exhibit significant potential across multiple domains due to their unique properties.However,conventional research methodologies face limitations in composition design,property prediction,and ...High-Entropy Alloys(HEAs)exhibit significant potential across multiple domains due to their unique properties.However,conventional research methodologies face limitations in composition design,property prediction,and process optimization,characterized by low efficiency and high costs.The integration of Artificial Intelligence(AI)technologies has provided innovative solutions for HEAs research.This review presented a detailed overview of recent advancements in AI applications for structural modeling and mechanical property prediction of HEAs.Furthermore,it discussed the advantages of big data analytics in facilitating alloy composition design and screening,quality control,and defect prediction,as well as the construction and sharing of specialized material databases.The paper also addressed the existing challenges in current AI-driven HEAs research,including issues related to data quality,model interpretability,and cross-domain knowledge integration.Additionally,it proposed prospects for the synergistic development of AI-enhanced computational materials science and experimental validation systems.展开更多
The utilization of nickel-based catalysts as alternatives to expensive platinum-based(Pt-based)materials for the hydrogen evolution reaction in acidic electrolytes has attracted considerable attention due to their pot...The utilization of nickel-based catalysts as alternatives to expensive platinum-based(Pt-based)materials for the hydrogen evolution reaction in acidic electrolytes has attracted considerable attention due to their potential for enabling cost-effective industrial applications.However,the unsatisfied cyclic stability and electrochemical activity limit their further application.In this work,nickel-molybdenum(Ni-Mo)alloy catalysts were successfully synthesized through a comprehensive process including electrodeposition,thermal annealing,and electrochemical activation.Owing to the synergistic interaction of molybdenum trinickelide(Ni_(3)Mo)and molybdenum dioxide(MoO_(2))in Ni-Mo alloy,the catalyst display superior overall electrochemical properties.A low overpotential of 86 mV at 10 mA/cm^(2)and a Tafel slope of 74.0 mV/dec in 0.5 mol/L H_(2)SO_(4)solution can be achieved.Notably,remarkable stability with negligible performance degradation even after 100 h could be maintained.This work presents a novel and effective strategy for the design and fabrication of high-performance,non-precious metal electrocatalysts for acidic water electrolysis.展开更多
Al-Cu-Mg-Ag alloys have become a research hotspot because of its good heat resistance.Its excellent mechanical properties are inseparable from the regulation of the structure by researchers.The method of material stru...Al-Cu-Mg-Ag alloys have become a research hotspot because of its good heat resistance.Its excellent mechanical properties are inseparable from the regulation of the structure by researchers.The method of material structure simulation has become more and more perfect.This study employs numerical simulation to investigate the microstructure evolution of Al-Cu-Mg-Ag alloys during solidification with the aim of controlling its structure.The size distribution of Ti-containing particles in an Al-Ti-B master alloy was characterized via microstructure observation,serving as a basis for optimizing the nucleation density parameters for particles of varying radii in the phase field model.The addition of refiner inhibited the growth of dendrites and no longer produced coarse dendrites.With the increase of refiner,the grains gradually tended to form cellular morphology.The refined grains were about 100μm in size.Experimental validation of the simulated as-cast grain morphology was conducted.The samples were observed by metallographic microscope and scanning electron microscope.The addition of refiner had a significant effect on the refinement of the alloy,and the average grain size after refinement was also about 100μm.At the same time,the XRD phase identification of the alloy was carried out.The observation of the microstructure morphology under the scanning electron microscope showed that the precipitated phase was mainly concentrated on the grain boundary.The Al_(2)Cu accounted for about 5%,and the matrix phase FCC accounted for about 95%,which also corresponded well with the simulation results.展开更多
Solid-state Na metal batteries(SSNBs),known for the low cost,high safety,and high energy density,hold a significant position in the next generation of rechargeable batteries.However,the urgent challenge of poor interf...Solid-state Na metal batteries(SSNBs),known for the low cost,high safety,and high energy density,hold a significant position in the next generation of rechargeable batteries.However,the urgent challenge of poor interfacial contact in solid-state electrolytes has hindered the commercialization of SSNBs.Driven by the concept of intimate electrode-electrolyte interface design,this study employs a combination of sodium-potassium(NaK)alloy and carbon nanotubes to prepare a semi-solid NaK(NKC)anode.Unlike traditional Na anodes,the paintable paste-like NKC anode exhibits superior adhesion and interface compatibility with both current collectors and gel electrolytes,significantly enhancing the physical contact of the electrode-electrolyte interface.Additionally,the filling of SiO_(2) nanoparticles improves the wettability of NaK alloy on gel polymer electrolytes,further achieving a conformal interface contact.Consequently,the overpotential of the NKC symmetric cell is markedly lower than that of the Na symmetric cell when subjected to a long cycle of 300 hrs.The full cell coupled with Na_(3)V_(2)(PO_(4))_(2) cathodes had an initial discharge capacity of 106.8 mAh·g^(-1) with a capacity retention of 89.61%after 300 cycles,and a high discharge capacity of 88.1 mAh·g^(-1) even at a high rate of 10 C.The outstanding electrochemical performance highlights the promising application potential of the NKC electrode.展开更多
High-entropy alloys(HEAs)have become essential materials in the aerospace and defense industries due to their remarkable mechanical properties,which include wear resistance,fatigue endurance,and corrosion resistance.T...High-entropy alloys(HEAs)have become essential materials in the aerospace and defense industries due to their remarkable mechanical properties,which include wear resistance,fatigue endurance,and corrosion resistance.The welding of high-entropy alloys is a cutting-edge field of study that is attracting a lot of interest and investigation from research organizations and businesses.Welding defects including porosity and cracks are challenging problem and limit the development of welding HEAs.This paper provides a comprehensive review of research on weldability of HEAs and the application of diverse welding techniques on welding HEAs over recent years.The forming mechanism and control strategies of defects during welding HEAs were provided in this work.Various welding techniques,including arc welding,laser welding,electron beam welding,friction stir welding,diffusion bonding and explosive welding,have been extensively investigated and applied to improve the microstructure and mechanical properties of HEAs joints.Furthermore,an in-depth review of the microstructure and mechanical properties of HEAs joints obtained by various welding methods is presented.This paper concludes with a discussion of the potential challenges associated with high-entropy alloy welding,thus providing valuable insights for future research efforts in this area.展开更多
To weaken the basal texture and in-plane anisotropy of magnesium alloy, non-basal slips are pre-enhanced by pre-rolling with a single pass larger strain reduction at elevated temperatures. Then Mg alloy sheets with th...To weaken the basal texture and in-plane anisotropy of magnesium alloy, non-basal slips are pre-enhanced by pre-rolling with a single pass larger strain reduction at elevated temperatures. Then Mg alloy sheets with the thickness of 1 mm are achieved after five passes rolling at 300 ℃. A double peak and disperse basal texture is generated after pre- rolling at higher temperatures when the non-basal slips are more active. So, the texture intensity of pre-rolled samples is reduced. Moreover, the distribution condition of in-grain misorientation axes (a method to analyze the activation of slips) shows that the pyramidal slip is quite active during deformation. After annealing on final rolled sheets, the texture distributions are changed and the intensity of texture reduces obviously due to static recrystallization. In particular, the r-value and in-plane anisotropy of pre-rolled samples are obviously lower than those of sample without pre-rolling.展开更多
基金Project supported by the Special Funding Support for the Development of 1500 Meter Subsea Christmas Tree and Control System,China。
文摘Improving interfacial bonding and alloying design are effective strategies for enhancing mechanical properties of particle-reinforced steel matrix composites(SMCs).This study prepared SMCs with uniformly distributed TiC_(P)in matrix using master alloying method.The TiC(002)/Fe(011)interface model was established based on the orientation relationship of(011)_(Fe)//(002)_(TiC),and[100]_(Fe)//[100]_(TiC).The effects of single and co-doping of alloying elements(Mn,Cr,Mo,Ni,Cu and Si)on the interface bonding behavior of TiC/Fe in composites were investigated in conjunction with first principles.The results demonstrate that the interface between TiC and matrix is continuous and stable.Compared to the undoped TiC/Fe interface,single-doping Mn,Cr,and Mo can improve the stability of TiC/Fe interface and enhance tensile strength.Conversely,single-doping with Ni,Cu,and Si reduced the interface stability and marginally reduces tensile strength.Relative to the undoped and singly Ni-doped TiC/Fe interfaces,the co-doping Ni-Mo boosts binding energy and separation work at the TiC/Fe interface,which is conducive to the interface bonding between TiC_(P)and matrix,and thus improves the mechanical properties of composites.Thus,in the alloying design of TiC particle reinforced low-alloy SMCs,incorporating Mn,Cr,Mo,and Ni into matrix can enhance the overall mechanical properties of composites.
基金Project(51501228)supported by the National Natural Science Foundation of ChinaProject(202109)supported by the Open Sharing Fund for the Large-scale Instruments and Equipments of Central South University,China。
文摘The effects of Yb/Zr micro-alloying on the microstructure,mechanical properties,and corrosion resistance of an Al-Zn-Mg-Cu alloy were systematically investigated.Upon the addition of Yb/Zr to the Al-Zn-Mg-Cu alloy,the grain boundaries were pinned by high-density nanosized Al_(3)(Yb,Zr)precipitates during extrusion deformation,consequently,the average grain size was significantly reduced from 232.7μm to 3.2μm.This grain refinement contributed substantially to the improvement in both strength and elongation.The ultimate tensile strength,yield strength,and elongation of the Yb/Zr modified alloy increased to 705.3 MPa,677.6 MPa,and 8.7%,respectively,representing enhancements of 16.2%,19.3%,and 112.2%compared to the unmodified alloy.Moreover,the distribution of MgZn_(2)phases along grain boundaries became more discontinuous in the Yb/Zr modified alloy,which effectively retarded the propagation of intergranular corrosion and improved the corrosion resistance.
基金Project(2007046) supported by High Technology Research Project of Jiangsu Province,China
文摘The cooperative effect of laser surface texturing(LST) and double glow plasma surface alloying on tribological performance of lubricated sliding contacts was investigated.A Nd:YAG laser was used to generate microdimples on steel surfaces. Dimples with the diameter of 150μm and the depth of 30-35μm distributed circumferentially on the disc surface.The alloying element Cr was sputtered to the laser texturing steel surface by double glow plasma technique.A deep diffusion layer with a thickness of 30μm and a high hardness of HV900 was formed in this alloy.Tribological experiments of three types of samples(smooth,texturing and texturing+alloying) were conducted with a ring-on-disc tribometer to simulate the face seal.It is found that,in comparison with smooth steel surfaces,the laser texturing samples significantly reduce the friction coefficient.Moreover,the lower wear rate of the sample treated with the two surface techniques is observed.
基金Projects(51935014,82072084,81871498)supported by the Natural Science Foundation of ChinaProjects(20192ACB20005,2020ACB214004)supported by the Jiangxi Provincial Natural Science Foundation of China+4 种基金Project(20201BBE51012)supported by the Provincial Key R&D Projects of Jiangxi Province,ChinaProject(2018)supported by the Guangdong Province Higher Vocational Colleges&Schools Pearl River Scholar Funded Scheme,ChinaProject(2017RS3008)supported by Hunan Provincial Science and Technology Plan,ChinaProject supported by the Open Research Fund of Jiangsu Key Laboratory of Precision and Micro-Manufacturing Technology,ChinaProject(2020M682114)China Postdoctoral Science Foundation。
文摘The slow degration of iron limits its bone implant application.The solid solution of Zn in Fe is expected to accelerate the degradation.In this work,mechanical alloying(MA)was used to prepare Fe-Zn powder with supersaturated solid solution.MA significantly decreased the lamellar spacing between particles,thus reducing the diffusion distance of solution atoms.Moreover,it caused a number of crystalline defects,which further promoted the solution diffusion.Subsequently,the MA-processed powder was consolidated into Fe-Zn part by laser sintering,which involved a partial melting/rapid solidification mechanism and retained the original supersaturated solid solution.Results proved that the Fe-Zn alloy became more susceptible with a lowered corrosion potential,and thereby an accelerated corrosion rate of(0.112±0.013)mm/year.Furthermore,it also exhibited favorable cell behavior.This work highlighted the advantage of MA combined with laser sintering for the preparation of Fe-Zn implant with improved degradation performance.
基金Project(2015DFR50990-01)supported by the International Cooperation Project of Ministry of Science and Technology of ChinaProject(2016KF-01)supported by the Shaanxi Key Laboratory of Nano-materials and Technology,ChinaProject(2015CXY-01)supported by the Cooperation Project on the Integration of Industry,Education and Research of Yulin Science and Technology Bureau,China。
文摘Mg-Zn binary alloys fabricated by the gas-phase alloying technique under vacuum condition were investigated in the state of initial state and after heat treatment for the microstructure and electrochemical behaviors.Different from the traditional Mg-Zn alloys preparation methods,alloys prepared by gas-phase alloying have a large number of intermetallic compounds,such as MgZn,Mg7Zn3 and MgZn2.After solution treatment,the boundary of the eutectic disappeared and the size ofα-Mg increased from 100μm to 150μm.At the same time,the value of the resistance of charge transfer increased,which indicates that the resistance of the charge transfer and the corrosion resistance of the alloys increased.After artificial aging treatment,the distribution ofα-Mg was more uniform and its size was reduced to about 50μm,and there was new eutectic structure formed.The newly formed eutectic structure forms galvanic cells with the alloy matrix,which makes the corrosion resistance of the alloy weaken.
基金Project(51401099)supported by the National Natural Science Foundation of ChinaProject(201501079)supported by the Doctor Startup Foundation of Liaoning Province,China
文摘The alloying effects of V on structural,elastic and electronic properties of TiFe_2 phase were investigated by the first-principles calculations based on the density functional theory.The calculated energy properties including cohesive energy and formation enthalpy indicate V atom would preferentially substitute on 6h sites of Fe atoms in the lattice of TiFe_2 to form the intermetallic Ti_4Fe_7(V).The calculated results of polycrystalline elastic parameters confirm that the plasticity of TiFe_2 would be improved with the addition of V.By discussing the percentage of elastic anisotropy,anisotropy in linear bulk modulus and directional dependence of elastic modulus,it is revealed that the anisotropy of TiFe_2 and Ti_4Fe_7(V) is small.Finally,the density of states,charge density distribution and Mulliken population for TiFe_2 and Ti_4Fe_7(V) were calculated,suggesting there is a mixed bonding with metallic,covalent and ionic nature in TiFe_2 and Ti_4Fe_7(V) compounds.These results also clarify that the reason for the improvement of plasticity with the addition of V in TiFe_2 is the weakened bonding of covalent feature between Ti and V atoms.
基金Project(50672134) supported by the National Natural Science Foundation of China
文摘Zr50Al15Ni10Cu25 amorphous powder was synthesized by mechanical alloying. The effect of Si3N4 addition on the crystallization behavior of the alloy during sintering process was studied. Thermal stability of the powders was performed by differential scanning calorimetry （DSC）. The phase and microstructure of the powders and bulk specimens sintered were determined by X-ray diffractometry （XRD） and scanning electron microscopy （SEM）. The results show that, introducing 0.05% （mass fraction） Si3N4 can enhance the crystallization activation energy of the ZZr50Al15Ni10Cu25 amorphous powders, which indicates that Si3N4 addition has hindrance effect on forming crystals from Zr50Al15Ni10Cu25amorphous powder. However, 0.10% Si3N4 results in the decrease of the crystallization activation energy, which makes its crystallization process easy to occur.
基金carried out with the partial financial support of Lao Feng xiang Co.Ltd.
文摘The mechanical properties of calcium(Ca) microalloyed 24 carat gold(Au 99.9 Ca 0.1) were measured and the corresponding microstructure was observed by TEM in order to investigate the strengthening mechanism.It was observed that the microalloying of 0.1wt% Ca improved the tensile strength(by 79% and 57% for the rolling and annealing states,respectively),hardness and E-Modulus as well as reduced the ductility of the 24 carat Au.Dispersed nano-sized precipitates and high density deformation twins were found in the rolled Au 99.9 Ca 0.1,which are attributed to be the major strengthening factors.The twins subsided after annealing and the strengthening of the annealed Au 99.9 Ca 0.1 is mainly contributed by the coarsened semi-coherent precipitates.
基金Fund Project for Transformation of Scientific and Technological Achievements of Jiangsu Province of China(BA2023020)。
文摘As an essential candidate for environment-friendly luminescent quantum dots(QDs),CuInS-based QDs have attracted more attention in recent years.However,several drawbacks still hamper their industrial applications,such as lower photoluminescence quantum yield(PLQY),complex synthetic pathways,uncontrollable emission spectra,and insufficient photostability.In this study,CuInZnS@ZnS core/shell QDs was prepared via a one-pot/three-step synthetic scheme with accurate and tunable control of PL spectra.Then their ensemble spectroscopic properties during nucleation formation,alloying,and ZnS shell growth processes were systematically investigated.PL peaks of these QDs can be precisely manipulated from 530 to 850 nm by controlling the stoichiometric ratio of Cu/In,Zn^(2+)doping and ZnS shell growth.In particular,CuInZnS@ZnS QDs possess a significantly long emission lifetime(up to 750 ns),high PLQY(up to 85%),and excellent crystallinity.Their spectroscopic evolution is well validated by Cu-deficient related intragap emission model.By controlling the stoichiometric ratio of Cu/In,two distinct Cu-deficient related emission pathways are established based on the differing oxidation states of Cu defects.Therefore,this work provides deeper insights for fabricating high luminescent ternary or quaternary-alloyed QDs.
基金financially supported by the Key Research and Development Program of Ningbo(Grant No.2023Z098)Natural Science Foundation of Inner Mongolia(Grant No.2023MS05040)+1 种基金Shenyang Collaborative Innovation Center Project for Multiple Energy Fields Composite Processing of Special Materials(Grant No.JG210027)Shenyang Key Technology Special Project of The Open Competition Mechanism to Select the Best Solution(Grant Nos.2022210101000827,2022-0-43-048).
文摘Titanium alloy has the advantages of high strength,strong corrosion resistance,excellent high and low temperature mechanical properties,etc.,and is widely used in aerospace,shipbuilding,weapons and equipment,and other fields.In recent years,with the continuous increase in demand for medium-thick plate titanium alloys,corresponding welding technologies have also continued to develop.Therefore,this article reviews the research progress of deep penetration welding technology for medium-thick plate titanium alloys,mainly covering traditional arc welding,high-energy beam welding,and other welding technologies.Among many methods,narrow gap welding,hybrid welding,and external energy field assistance welding all contribute to improving the welding efficiency and quality of medium-thick plate titanium alloys.Finally,the development trend of deep penetration welding technology for mediumthick plate titanium alloys is prospected.
文摘As an efficient passive anti-icing method,the superhydrophobic surface can reduce icing process on metals in low temperatures.However,the usual organic low-surface-energy decorations are often prone to age especially in harsh environments,leading to a decrease or complete failure of the anti-icing performance.Here,we adopt a fabrication method of femtosecond laser element-doping microstructuring to achieve inor-ganic superhydrophobic aluminum alloys surfaces through simultaneously modifying the surface profile and compositions of aluminum alloys.The obtained bionic anthill tribe structure with the low thermal conductiv-ity,exhibits the superior delayed freezing time(803.3 s)and the low ice adhesion(16μN)in comparison to the fluorosilane modified and bare Al surfaces.Moreover,such an inherently superhydrophobic metal sur-face also shows the exceptional environmental durability in anti-icing performance,which confirms the ef-fectiveness of our superhydrophobic surface without the need for organic coatings.
文摘The effects of different warm rolling(WR)reductions on the microstructure and mechanical properties of low-Cr FeCrAl alloys at both room and elevated temperatures were investigated.The study revealed that when the WR reduction is small,it effectively refines the grains and forms a large number of subgrains in the matrix,while also inducing the dissolution of the Laves phase.This enhances the mechanical properties of FeCrAl alloys primarily through grain refinement and solid solution strengthening.Conversely,with larger WR reductions,the grain refinement effect diminishes,but a significant number of Laves phases form in the matrix,strengthening the alloys primarily through precipitation strengthening.WR exhibited a remarkable enhancing effect on the comprehensive mechanical properties at both room and high temperatures,with a signi-ficant enhancement in ductility at high temperatures.Notably,a 10%WR reduction resulted in the optimal overall mechanical properties at both room and elevated temperatures.
文摘Zirconium alloy(Zr-4)is extensively utilized in nuclear fuel cladding materials due to its exceptional neutron economy,high ductility,and promising corrosion and irradiation resistance.Nevertheless,during the operational lifespan of the Zr-4 fuel tube,micro-oscillations induced by the high-speed flow of cooling water can cause wear between the cladding tube and grids.This leads to wear failure of the Zr-4 alloy tube,which seriously threatens the safe operation of nuclear stations.The application of protective coatings onto the surface of zirconium alloys serves to enhance their resistance against wear,while without changing of the existing reactor structure.In this study,FeCrAl/CrN and FeCrAl coatings were fabricated on the surface of Zr-4 alloy using dual-target co-sputtering technology.The effects of the CrN interlayer on the microstructure,mechanical properties,and tribological behavior of FeCrAl coating in air and B-Li water were investigated,and a comparative analysis with Zr-4 alloy was conducted.The results showed that the application of FeCrAl/CrN and FeCrAl coatings significantly enhanced the hardness and wear resistance of Zr-4 alloy.The introduction of the CrN interlayer increased the columnar grain size of the FeCrAl coating and caused a change in the preferred growth direction of the coating from(110)to(211).The CrN interlayer improved the hardness and wear resistance of the coating,it also led to a decrease in adhesion strength.The wear rates of FeCrAl/CrN coatings in air and B-Li water were the lowest,about 3.2×10^(-6) mm^(3)/(N·m)and 6.0×10^(-7) mm^(3)/(N·m),respectively.The lubricating effect of B-Li water effectively reduced the friction coefficient and wear rate of both FeCrAl/CrN and FeCrAl coatings.In air and B-Li water,the primary wear mechanisms for Zr-4 are adhesive wear and oxidative wear,while the main wear mechanisms for FeCrAl/CrN and FeCrAl coatings are abrasive wear and oxidative wear.These findings not only provided a theoretical basis for understanding the microstructure and wear performance of FeCrAl coatings but also offered important technical guidance for their practical application in the nuclear industry.
文摘Metal-organic frameworks(MOFs)are import-ant as possible energy storage materials.Nitrogen-doped iron-cobalt MOFs were synthesized by a one-pot solvo-thermal method using CoCl_(3)·6H_(2)O and FeCl_(3)·6H_(2)O dis-solved in N,N-dimethylformamide,and were converted into Fe-Co embedded in N-doped porous carbon polyhedra by pyrolysis in a nitrogen atmosphere.During pyrolysis,the or-ganic ligands transformed into N-doped porous carbon which improved their structural stability and also their electrical contact with other materials.The Fe and Co are tightly bound together because of their encapsulation by the carbon nitride and are well dispersed in the carbon matrix,and improve the material’s conductivity and stability and provide additional capacity.When used as the anode for lithium-ion batteries,the material gives an initial capacity of up to 2230.7 mAh g^(-1)and a reversible capa-city of 1146.3 mAh g^(-1)is retained after 500 cycles at a current density of 0.5 A g^(-1),making it an excellent candidate for this purpose.
文摘High-Entropy Alloys(HEAs)exhibit significant potential across multiple domains due to their unique properties.However,conventional research methodologies face limitations in composition design,property prediction,and process optimization,characterized by low efficiency and high costs.The integration of Artificial Intelligence(AI)technologies has provided innovative solutions for HEAs research.This review presented a detailed overview of recent advancements in AI applications for structural modeling and mechanical property prediction of HEAs.Furthermore,it discussed the advantages of big data analytics in facilitating alloy composition design and screening,quality control,and defect prediction,as well as the construction and sharing of specialized material databases.The paper also addressed the existing challenges in current AI-driven HEAs research,including issues related to data quality,model interpretability,and cross-domain knowledge integration.Additionally,it proposed prospects for the synergistic development of AI-enhanced computational materials science and experimental validation systems.
基金supported by the National Natural Science Foundation of China(22179138).
文摘The utilization of nickel-based catalysts as alternatives to expensive platinum-based(Pt-based)materials for the hydrogen evolution reaction in acidic electrolytes has attracted considerable attention due to their potential for enabling cost-effective industrial applications.However,the unsatisfied cyclic stability and electrochemical activity limit their further application.In this work,nickel-molybdenum(Ni-Mo)alloy catalysts were successfully synthesized through a comprehensive process including electrodeposition,thermal annealing,and electrochemical activation.Owing to the synergistic interaction of molybdenum trinickelide(Ni_(3)Mo)and molybdenum dioxide(MoO_(2))in Ni-Mo alloy,the catalyst display superior overall electrochemical properties.A low overpotential of 86 mV at 10 mA/cm^(2)and a Tafel slope of 74.0 mV/dec in 0.5 mol/L H_(2)SO_(4)solution can be achieved.Notably,remarkable stability with negligible performance degradation even after 100 h could be maintained.This work presents a novel and effective strategy for the design and fabrication of high-performance,non-precious metal electrocatalysts for acidic water electrolysis.
文摘Al-Cu-Mg-Ag alloys have become a research hotspot because of its good heat resistance.Its excellent mechanical properties are inseparable from the regulation of the structure by researchers.The method of material structure simulation has become more and more perfect.This study employs numerical simulation to investigate the microstructure evolution of Al-Cu-Mg-Ag alloys during solidification with the aim of controlling its structure.The size distribution of Ti-containing particles in an Al-Ti-B master alloy was characterized via microstructure observation,serving as a basis for optimizing the nucleation density parameters for particles of varying radii in the phase field model.The addition of refiner inhibited the growth of dendrites and no longer produced coarse dendrites.With the increase of refiner,the grains gradually tended to form cellular morphology.The refined grains were about 100μm in size.Experimental validation of the simulated as-cast grain morphology was conducted.The samples were observed by metallographic microscope and scanning electron microscope.The addition of refiner had a significant effect on the refinement of the alloy,and the average grain size after refinement was also about 100μm.At the same time,the XRD phase identification of the alloy was carried out.The observation of the microstructure morphology under the scanning electron microscope showed that the precipitated phase was mainly concentrated on the grain boundary.The Al_(2)Cu accounted for about 5%,and the matrix phase FCC accounted for about 95%,which also corresponded well with the simulation results.
基金National Natural Science Foundation of China (52073253)。
文摘Solid-state Na metal batteries(SSNBs),known for the low cost,high safety,and high energy density,hold a significant position in the next generation of rechargeable batteries.However,the urgent challenge of poor interfacial contact in solid-state electrolytes has hindered the commercialization of SSNBs.Driven by the concept of intimate electrode-electrolyte interface design,this study employs a combination of sodium-potassium(NaK)alloy and carbon nanotubes to prepare a semi-solid NaK(NKC)anode.Unlike traditional Na anodes,the paintable paste-like NKC anode exhibits superior adhesion and interface compatibility with both current collectors and gel electrolytes,significantly enhancing the physical contact of the electrode-electrolyte interface.Additionally,the filling of SiO_(2) nanoparticles improves the wettability of NaK alloy on gel polymer electrolytes,further achieving a conformal interface contact.Consequently,the overpotential of the NKC symmetric cell is markedly lower than that of the Na symmetric cell when subjected to a long cycle of 300 hrs.The full cell coupled with Na_(3)V_(2)(PO_(4))_(2) cathodes had an initial discharge capacity of 106.8 mAh·g^(-1) with a capacity retention of 89.61%after 300 cycles,and a high discharge capacity of 88.1 mAh·g^(-1) even at a high rate of 10 C.The outstanding electrochemical performance highlights the promising application potential of the NKC electrode.
基金Project(52105351)supported by the National Natural Science Foundation of ChinaProject(24KJA460002)supported by the Natural Science Foundation of the Higher Education Institutions of Jiangsu Province,ChinaProject(G2023014009L)supported by the High-end Foreign Experts Recruitment Plan of China。
文摘High-entropy alloys(HEAs)have become essential materials in the aerospace and defense industries due to their remarkable mechanical properties,which include wear resistance,fatigue endurance,and corrosion resistance.The welding of high-entropy alloys is a cutting-edge field of study that is attracting a lot of interest and investigation from research organizations and businesses.Welding defects including porosity and cracks are challenging problem and limit the development of welding HEAs.This paper provides a comprehensive review of research on weldability of HEAs and the application of diverse welding techniques on welding HEAs over recent years.The forming mechanism and control strategies of defects during welding HEAs were provided in this work.Various welding techniques,including arc welding,laser welding,electron beam welding,friction stir welding,diffusion bonding and explosive welding,have been extensively investigated and applied to improve the microstructure and mechanical properties of HEAs joints.Furthermore,an in-depth review of the microstructure and mechanical properties of HEAs joints obtained by various welding methods is presented.This paper concludes with a discussion of the potential challenges associated with high-entropy alloy welding,thus providing valuable insights for future research efforts in this area.
基金Project(52374395) supported by the National Natural Science Foundations of ChinaProjects(20210302123135,20210302123163) supported by the Natural Science Foundation of Shanxi Province,China+2 种基金Projects(YDZJSX20231B003,YDZJSX2021A010) supported by the Central Government Guided Local Science and Technology Development Projects,ChinaProject(2022M710541) supported by the China Postdoctoral Science FoundationProjects(202104021301022,202204021301009) supported by the Scientific and Technological Achievements Transformation Guidance Special Project of Shanxi Province,China。
文摘To weaken the basal texture and in-plane anisotropy of magnesium alloy, non-basal slips are pre-enhanced by pre-rolling with a single pass larger strain reduction at elevated temperatures. Then Mg alloy sheets with the thickness of 1 mm are achieved after five passes rolling at 300 ℃. A double peak and disperse basal texture is generated after pre- rolling at higher temperatures when the non-basal slips are more active. So, the texture intensity of pre-rolled samples is reduced. Moreover, the distribution condition of in-grain misorientation axes (a method to analyze the activation of slips) shows that the pyramidal slip is quite active during deformation. After annealing on final rolled sheets, the texture distributions are changed and the intensity of texture reduces obviously due to static recrystallization. In particular, the r-value and in-plane anisotropy of pre-rolled samples are obviously lower than those of sample without pre-rolling.
