The half-dry cutting employs cryogenic compressed air cooled down to (10 to 40) and a micro-dosage of lubricating oil, called cryogenic cold air jet cutting was studied. On the basis of a comparative experiment on dr...The half-dry cutting employs cryogenic compressed air cooled down to (10 to 40) and a micro-dosage of lubricating oil, called cryogenic cold air jet cutting was studied. On the basis of a comparative experiment on dry and cryogenic cold air jet cuttings carried out for grade 45 steel, the effects of cryogenic cold air jet on the breaking of chips were discussed. The experimental results reveal that in the valid ranges of pressure and temperature, the cryogenic cold air jet widens the chip breaking areas effectively. When the cutting depth is not greater than 1 mm, the influence of chip breaking is much more significant. But different injecting angle of cold air has different influence on the chip-break. From the experiment, the optimized jet injecting angle, temperature effecting range and pressure working range of cold air are obtained. These results can offer a foundation for industrial manufacturing.展开更多
In order to form an atmospheric-pressure plasma jet without airflow, a needle–ring electrode structure is proposed in this paper. When heteropolar potentials are applied to a needle and a ring, a marked electric fiel...In order to form an atmospheric-pressure plasma jet without airflow, a needle–ring electrode structure is proposed in this paper. When heteropolar potentials are applied to a needle and a ring, a marked electric field strength enhancement around the needle’s pointed end has been found. When the same potential is applied to both the needle and the ring, the lateral electric field strength for the needle can be weakened. By using the above two methods, an increase of the difference between the pointed end electric field strength and the lateral one is achieved and stable plasma jets are formed. A symmetrical space electric field distribution is established at the pointed end of the needles when several sets of heteropolar needle–ring electrodes are uniformly arranged, which is conducive to forming a uniform array plasma jet. Under DC discharge conditions, a safe and stable plasma jet of high density and an array plasma jet are successfully achieved.展开更多
Plasma synthetic jet actuator（PSJA） has a wide application prospect in the high-speed flow control field for its high jet velocity.In this paper,the influence of the air pressure on the performance of a two-electrod...Plasma synthetic jet actuator（PSJA） has a wide application prospect in the high-speed flow control field for its high jet velocity.In this paper,the influence of the air pressure on the performance of a two-electrode PSJA is investigated by the schlieren method in a large range from 7 k Pa to 100 k Pa.The energy consumed by the PSJA is roughly the same for all the pressure levels.Traces of the precursor shock wave velocity and the jet front velocity vary a lot for different pressures.The precursor shock wave velocity first decreases gradually and then remains at 345 m/s as the air pressure increases.The peak jet front velocity always appears at the first appearance of a jet,and it decreases gradually with the increase of the air pressure.A maximum precursor shock wave velocity of 520 m/s and a maximum jet front velocity of 440 m/s are observed at the pressure of 7 k Pa.The averaged jet velocity in one period ranges from 44 m/s to 54 m/s for all air pressures,and it drops with the rising of the air pressure.High velocities of the precursor shock wave and the jet front indicate that this type of PSJA can still be used to influence the high-speed flow field at 7 k Pa.展开更多
In order to investigate whether an air–water plasma jet is beneficial to improve the efficiency of inactivation, a series of experiments were done using a ring-needle plasma jet. The water content in the working gas...In order to investigate whether an air–water plasma jet is beneficial to improve the efficiency of inactivation, a series of experiments were done using a ring-needle plasma jet. The water content in the working gas（air） was accurately measured based on the Karl Fischer method. The effects of water on the production of OH（A;Σ;–X;Π;） and O（3p;P–3s;S） were also studied by optical emission spectroscopy. The results show that the water content is in the range of 2.53–9.58 mg l;, depending on the gas/water mixture ratio. The production of OH（A;Σ;–X;Π;） rises with the increase of water content, whereas the O（3p;P–3s;S） shows a declining tendency with higher water content. The sterilization experiments indicate that this air–water plasma jet inactivates the P. digitatum spores very effectively and its efficiency rises with the increase of the water content. It is possible that OH（A;Σ;–X;Π;） is a more effective species in inactivation than O（3p;P–3s;S） and the water content benefit the spore germination inhibition through rising the OH（A;Σ;–X;Π;） production. The maximum of the inactivation efficacy is up to 93% when the applied voltage is -6.75 kV and the water content is 9.58 mg l;.展开更多
An atmospheric pressure dielectric barrier discharge （DBD） plasma jet generator using air flow as the feedstock gas was applied to decontaminate the chemical agent surrogates on the surface of aluminum, stainless st...An atmospheric pressure dielectric barrier discharge （DBD） plasma jet generator using air flow as the feedstock gas was applied to decontaminate the chemical agent surrogates on the surface of aluminum, stainless steel or iron plate painted with alkyd or PVC. The experi- mental results of material decontamination show that the residual chemical agent on the material is lower than the permissible value of the National Military Standard of China. In order to test the corrosion effect of the plasma jet on different material surfaces in the decontamination pro-cess, corrosion tests for the materials of polymethyl methacrylate, neoprene, polyvinyl chloride （PVC）, polyethylene （PE）, phenolic resin, iron plate painted with alkyd, stainless steel, aluminum, etc. were carried out, and relevant parameters were examined, including etiolation index, chroma- tism, loss of gloss, corrosion form, etc. The results show that the plasma jet is slightly corrosive for part of the materials, but their performances are not affected. A portable calculator, computer display, mainboard, circuit board of radiogram, and a hygrometer could work normally after being treated by the plasma jet.展开更多
The effective smoke preventing installation should have the functions such as absolute smoke insulation, going into and coming off the smoke preventing place freely, no confinement of sight. The smoke preventing ai...The effective smoke preventing installation should have the functions such as absolute smoke insulation, going into and coming off the smoke preventing place freely, no confinement of sight. The smoke preventing air curtain is the most effective. Based on the previous researches done by others, the flow field is theoretically analyzed and the calculating method for the smoke preventing air curtain of high rise buildings is inferred by means of mathematics in this paper.展开更多
This paper is concerned with three-dimensional numerical simulation of a plunging liquid jet. The transient processes of forming an air cavity around the jet, capturing an initially large air bubble, and the break-up ...This paper is concerned with three-dimensional numerical simulation of a plunging liquid jet. The transient processes of forming an air cavity around the jet, capturing an initially large air bubble, and the break-up of this large toroidal-shaped bubble into smaller bubbles were analyzed. A stabilized finite element method （FEM） was employed under parallel numerical simulations based on adaptive, unstructured grid and coupled with a level-set method to track the interface between air and liquid. These simulations show that the inertia of the liquid jet initially depresses the pool＇s surface, forming an annular air cavity which surrounds the liquid jet. A toroidal liquid eddy which is subse- quently formed in the liquid pool results in air cavity collapse, and in turn entrains air into the liquid pool from the unstable annular air gap region around the liquid jet.展开更多
This letter reports on the generation and characteristics of a large-scale dielectric barrier discharge plasma jet at atmospheric pressure. With appropriate parameters, diffuse plasma with a 50×5 mm2 cross-sectio...This letter reports on the generation and characteristics of a large-scale dielectric barrier discharge plasma jet at atmospheric pressure. With appropriate parameters, diffuse plasma with a 50×5 mm2 cross-sectional area is obtained. The characteristics of the discharges are diag- nosed by using electrical and optical methods. In addition to being generated in helium, plasma is also generated in a mixed gas of helium and oxygen. The oxygen atomic radiant intensity （3p5P→ 3s5S, 3p3P→3s3S transition） is not proportional to the proportion of oxygen in the gas mixture, as shown by the experimental results.展开更多
In this paper,the air plasma jet produced by micro-hollow cathode discharge(MHCD)is investigated.The discharge is powered by a positive nanosecond pulse high voltage supply.The waveforms of the discharge,the images of...In this paper,the air plasma jet produced by micro-hollow cathode discharge(MHCD)is investigated.The discharge is powered by a positive nanosecond pulse high voltage supply.The waveforms of the discharge,the images of the jet,the evolution of the plasma bullet and the reactive species are obtained to analyze the characteristics of the MHCD plasma jet.It is found that the length of the plasma jet is almost proportional to the air flow rate of 2–6 slm.Two plasma bullets appear one after another during a single period of the voltage waveform,and both of the two plasma bullets are formed during the positive pulse voltage off.The propagation velocity of the two plasma bullets is on the order of several hundred m/s,which is approximate to that of the air flow.These results indicate that the gas flow has an important influence on the formation of this MHCD plasma jet.展开更多
文摘The half-dry cutting employs cryogenic compressed air cooled down to (10 to 40) and a micro-dosage of lubricating oil, called cryogenic cold air jet cutting was studied. On the basis of a comparative experiment on dry and cryogenic cold air jet cuttings carried out for grade 45 steel, the effects of cryogenic cold air jet on the breaking of chips were discussed. The experimental results reveal that in the valid ranges of pressure and temperature, the cryogenic cold air jet widens the chip breaking areas effectively. When the cutting depth is not greater than 1 mm, the influence of chip breaking is much more significant. But different injecting angle of cold air has different influence on the chip-break. From the experiment, the optimized jet injecting angle, temperature effecting range and pressure working range of cold air are obtained. These results can offer a foundation for industrial manufacturing.
基金supported by National Natural Science Foundation of China (No. 51577011)
文摘In order to form an atmospheric-pressure plasma jet without airflow, a needle–ring electrode structure is proposed in this paper. When heteropolar potentials are applied to a needle and a ring, a marked electric field strength enhancement around the needle’s pointed end has been found. When the same potential is applied to both the needle and the ring, the lateral electric field strength for the needle can be weakened. By using the above two methods, an increase of the difference between the pointed end electric field strength and the lateral one is achieved and stable plasma jets are formed. A symmetrical space electric field distribution is established at the pointed end of the needles when several sets of heteropolar needle–ring electrodes are uniformly arranged, which is conducive to forming a uniform array plasma jet. Under DC discharge conditions, a safe and stable plasma jet of high density and an array plasma jet are successfully achieved.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.51407197,51522606,51336011,91541120,and 11472306)
文摘Plasma synthetic jet actuator（PSJA） has a wide application prospect in the high-speed flow control field for its high jet velocity.In this paper,the influence of the air pressure on the performance of a two-electrode PSJA is investigated by the schlieren method in a large range from 7 k Pa to 100 k Pa.The energy consumed by the PSJA is roughly the same for all the pressure levels.Traces of the precursor shock wave velocity and the jet front velocity vary a lot for different pressures.The precursor shock wave velocity first decreases gradually and then remains at 345 m/s as the air pressure increases.The peak jet front velocity always appears at the first appearance of a jet,and it decreases gradually with the increase of the air pressure.A maximum precursor shock wave velocity of 520 m/s and a maximum jet front velocity of 440 m/s are observed at the pressure of 7 k Pa.The averaged jet velocity in one period ranges from 44 m/s to 54 m/s for all air pressures,and it drops with the rising of the air pressure.High velocities of the precursor shock wave and the jet front indicate that this type of PSJA can still be used to influence the high-speed flow field at 7 k Pa.
基金supported by National Natural Science Foundation of China (NSFC) under Grants No. 51407020National Key Technology Research and Development Program of the Ministry of Science and Technology of China under Grants No. 2014BAC13B05Visiting Scholarship of State Key Laboratory of Power Transmission Equipment & System Security and New Technology (Chongqing University) No. 2007DA10512716404
文摘In order to investigate whether an air–water plasma jet is beneficial to improve the efficiency of inactivation, a series of experiments were done using a ring-needle plasma jet. The water content in the working gas（air） was accurately measured based on the Karl Fischer method. The effects of water on the production of OH（A;Σ;–X;Π;） and O（3p;P–3s;S） were also studied by optical emission spectroscopy. The results show that the water content is in the range of 2.53–9.58 mg l;, depending on the gas/water mixture ratio. The production of OH（A;Σ;–X;Π;） rises with the increase of water content, whereas the O（3p;P–3s;S） shows a declining tendency with higher water content. The sterilization experiments indicate that this air–water plasma jet inactivates the P. digitatum spores very effectively and its efficiency rises with the increase of the water content. It is possible that OH（A;Σ;–X;Π;） is a more effective species in inactivation than O（3p;P–3s;S） and the water content benefit the spore germination inhibition through rising the OH（A;Σ;–X;Π;） production. The maximum of the inactivation efficacy is up to 93% when the applied voltage is -6.75 kV and the water content is 9.58 mg l;.
文摘An atmospheric pressure dielectric barrier discharge （DBD） plasma jet generator using air flow as the feedstock gas was applied to decontaminate the chemical agent surrogates on the surface of aluminum, stainless steel or iron plate painted with alkyd or PVC. The experi- mental results of material decontamination show that the residual chemical agent on the material is lower than the permissible value of the National Military Standard of China. In order to test the corrosion effect of the plasma jet on different material surfaces in the decontamination pro-cess, corrosion tests for the materials of polymethyl methacrylate, neoprene, polyvinyl chloride （PVC）, polyethylene （PE）, phenolic resin, iron plate painted with alkyd, stainless steel, aluminum, etc. were carried out, and relevant parameters were examined, including etiolation index, chroma- tism, loss of gloss, corrosion form, etc. The results show that the plasma jet is slightly corrosive for part of the materials, but their performances are not affected. A portable calculator, computer display, mainboard, circuit board of radiogram, and a hygrometer could work normally after being treated by the plasma jet.
文摘The effective smoke preventing installation should have the functions such as absolute smoke insulation, going into and coming off the smoke preventing place freely, no confinement of sight. The smoke preventing air curtain is the most effective. Based on the previous researches done by others, the flow field is theoretically analyzed and the calculating method for the smoke preventing air curtain of high rise buildings is inferred by means of mathematics in this paper.
基金supported by the Office of Naval Research(Grant ONRDC14292111)
文摘This paper is concerned with three-dimensional numerical simulation of a plunging liquid jet. The transient processes of forming an air cavity around the jet, capturing an initially large air bubble, and the break-up of this large toroidal-shaped bubble into smaller bubbles were analyzed. A stabilized finite element method （FEM） was employed under parallel numerical simulations based on adaptive, unstructured grid and coupled with a level-set method to track the interface between air and liquid. These simulations show that the inertia of the liquid jet initially depresses the pool＇s surface, forming an annular air cavity which surrounds the liquid jet. A toroidal liquid eddy which is subse- quently formed in the liquid pool results in air cavity collapse, and in turn entrains air into the liquid pool from the unstable annular air gap region around the liquid jet.
基金supported by National Natural Science Foundation of China(Nos.10775027,50807011)
文摘This letter reports on the generation and characteristics of a large-scale dielectric barrier discharge plasma jet at atmospheric pressure. With appropriate parameters, diffuse plasma with a 50×5 mm2 cross-sectional area is obtained. The characteristics of the discharges are diag- nosed by using electrical and optical methods. In addition to being generated in helium, plasma is also generated in a mixed gas of helium and oxygen. The oxygen atomic radiant intensity （3p5P→ 3s5S, 3p3P→3s3S transition） is not proportional to the proportion of oxygen in the gas mixture, as shown by the experimental results.
基金supported by National Natural Science Foundation of China(No.11475019)。
文摘In this paper,the air plasma jet produced by micro-hollow cathode discharge(MHCD)is investigated.The discharge is powered by a positive nanosecond pulse high voltage supply.The waveforms of the discharge,the images of the jet,the evolution of the plasma bullet and the reactive species are obtained to analyze the characteristics of the MHCD plasma jet.It is found that the length of the plasma jet is almost proportional to the air flow rate of 2–6 slm.Two plasma bullets appear one after another during a single period of the voltage waveform,and both of the two plasma bullets are formed during the positive pulse voltage off.The propagation velocity of the two plasma bullets is on the order of several hundred m/s,which is approximate to that of the air flow.These results indicate that the gas flow has an important influence on the formation of this MHCD plasma jet.
