A fuzzy model was presented to predict the weldment shape profile of submerged arc welds （SAW） including the shape of heat affected zone （HAZ）. The SAW bead-on-plates were welded by following a full factorial desi...A fuzzy model was presented to predict the weldment shape profile of submerged arc welds （SAW） including the shape of heat affected zone （HAZ）. The SAW bead-on-plates were welded by following a full factorial design matrix. The design matrix consisted of three levels of input welding process parameters. The welds were cross-sectioned and etched, and the zones were measured. A mapping technique was used to measure the various segments of the weld zones. These mapped zones were used to build a fuzzy logic model. The membership functions of the fuzzy model were chosen for the accurate prediction of the weld zone. The fuzzy model was further tested for a set of test case data. The weld zone predicted by the fuzzy logic model was compared with the experimentally obtained shape profiles and close agreement between the two was noted. The mapping technique developed for the weld zones and the fuzzy logiemodel earl be used for on-line control of the SAW process. From the SAW fuzzy logic model an estimation of the fusion and HAZ can also be developed.展开更多
Pitting and stress corrosion cracking(SCC) studies on the 316 N stainless steel(SS) weldments in aswelded(AW) and thermally aged(solution annealing(SA), 550C/4 h and 750C/1 h) conditions were carried out in acidic and...Pitting and stress corrosion cracking(SCC) studies on the 316 N stainless steel(SS) weldments in aswelded(AW) and thermally aged(solution annealing(SA), 550C/4 h and 750C/1 h) conditions were carried out in acidic and acidic chloride media. Pitting corrosion and SCC resistance was the highest for SA weldment, which was attributed to homogenization of microstructural and microchemical heterogeneities during solution annealing. SA specimen showed the most stable passive film as compared to AW weldment because of higher amount of delta-ferrite in AW weld metal, which resulted in an increased heterogeneity and inferior SCC resistance in AW. Stability of passive film was found to be adversely affected due to heat treatments(at 550C/4 h and 750C/1 h) because of the precipitation of carbide and sigma phases.展开更多
The weldments for several types of high Cr ferritic steels were investigated to understand the fracture mechanism of the Type IV crack. The creep testing shows that the Type IV cracking is more likely to occur at the ...The weldments for several types of high Cr ferritic steels were investigated to understand the fracture mechanism of the Type IV crack. The creep testing shows that the Type IV cracking is more likely to occur at the lower stress level, whereas at the higher stress level the crack shifts towards parent metal. The microstructures observed in the HAZ for all the materials are mostly tempered lath martensites. There was no δ ferrites found in all creep specimens.展开更多
This present study applied gas tungsten arc welding in order to join AISI 304 and AISI 201 stainless steels.The objective was to find the optimum welding condition that gave a weld bead in accordance with DIN EN ISO 2...This present study applied gas tungsten arc welding in order to join AISI 304 and AISI 201 stainless steels.The objective was to find the optimum welding condition that gave a weld bead in accordance with DIN EN ISO 25817 quality level B, pitting corrosion potential of the weld metal of not less than that of the AISI304 base metal and a ratio of delta-ferrite in austenite matrix of the weld metal of not lower than 3%.Such a ratio is a criterion widely accepted to protect the weld metal from solidification cracking. At the welding current of 75 A and by using pure argon as a shielding gas 0 to 8 vol.% and applying a welding speed in the range of 2-3.5 mm·s^(-1) was found to give a complete weld bead with an increased depthper-width ratio(promote weldability). For welding speed in the range of 3 and 3.5 mm·s^(-1)(promote corrosion resistance). Increasing the welding speed in such a range decreased the amount of delta-ferrite in the austenite matrix, and increased the pitting corrosion potential of the weld metal to be 302 mV_(SCE).This value was still lower than the pitting corrosion potential of the AISI 304 base metal. Mixing nitrogen in argon shielding gas increased the nitrogen content in the weld. The optimum condition was found when using a welding speed of 3 mm· s^(-1) and mixing 1 vol.% of nitrogen in the argon shielding gas(promote weldability and corrosion resistance). Pitted areas after potentiodynamic test were observed in the austenite in which its Cr content was relatively low.展开更多
基金Supported by the IIT Roorkee Project under Grant No. FIG-A Scheme-A
文摘A fuzzy model was presented to predict the weldment shape profile of submerged arc welds （SAW） including the shape of heat affected zone （HAZ）. The SAW bead-on-plates were welded by following a full factorial design matrix. The design matrix consisted of three levels of input welding process parameters. The welds were cross-sectioned and etched, and the zones were measured. A mapping technique was used to measure the various segments of the weld zones. These mapped zones were used to build a fuzzy logic model. The membership functions of the fuzzy model were chosen for the accurate prediction of the weld zone. The fuzzy model was further tested for a set of test case data. The weld zone predicted by the fuzzy logic model was compared with the experimentally obtained shape profiles and close agreement between the two was noted. The mapping technique developed for the weld zones and the fuzzy logiemodel earl be used for on-line control of the SAW process. From the SAW fuzzy logic model an estimation of the fusion and HAZ can also be developed.
文摘Pitting and stress corrosion cracking(SCC) studies on the 316 N stainless steel(SS) weldments in aswelded(AW) and thermally aged(solution annealing(SA), 550C/4 h and 750C/1 h) conditions were carried out in acidic and acidic chloride media. Pitting corrosion and SCC resistance was the highest for SA weldment, which was attributed to homogenization of microstructural and microchemical heterogeneities during solution annealing. SA specimen showed the most stable passive film as compared to AW weldment because of higher amount of delta-ferrite in AW weld metal, which resulted in an increased heterogeneity and inferior SCC resistance in AW. Stability of passive film was found to be adversely affected due to heat treatments(at 550C/4 h and 750C/1 h) because of the precipitation of carbide and sigma phases.
文摘The weldments for several types of high Cr ferritic steels were investigated to understand the fracture mechanism of the Type IV crack. The creep testing shows that the Type IV cracking is more likely to occur at the lower stress level, whereas at the higher stress level the crack shifts towards parent metal. The microstructures observed in the HAZ for all the materials are mostly tempered lath martensites. There was no δ ferrites found in all creep specimens.
基金the Thai Government scholarship given via Rajamangala University of Technology Krungthep (UTK), Bangkok, Thailand, for their financial support through this funded research project
文摘This present study applied gas tungsten arc welding in order to join AISI 304 and AISI 201 stainless steels.The objective was to find the optimum welding condition that gave a weld bead in accordance with DIN EN ISO 25817 quality level B, pitting corrosion potential of the weld metal of not less than that of the AISI304 base metal and a ratio of delta-ferrite in austenite matrix of the weld metal of not lower than 3%.Such a ratio is a criterion widely accepted to protect the weld metal from solidification cracking. At the welding current of 75 A and by using pure argon as a shielding gas 0 to 8 vol.% and applying a welding speed in the range of 2-3.5 mm·s^(-1) was found to give a complete weld bead with an increased depthper-width ratio(promote weldability). For welding speed in the range of 3 and 3.5 mm·s^(-1)(promote corrosion resistance). Increasing the welding speed in such a range decreased the amount of delta-ferrite in the austenite matrix, and increased the pitting corrosion potential of the weld metal to be 302 mV_(SCE).This value was still lower than the pitting corrosion potential of the AISI 304 base metal. Mixing nitrogen in argon shielding gas increased the nitrogen content in the weld. The optimum condition was found when using a welding speed of 3 mm· s^(-1) and mixing 1 vol.% of nitrogen in the argon shielding gas(promote weldability and corrosion resistance). Pitted areas after potentiodynamic test were observed in the austenite in which its Cr content was relatively low.
