A novel dual-band ISGW cavity filter with enhanced frequency selectivity is proposed in this paper by utilizing a multi-mode coupling topology.Its cavity is designed to control the number of modes,and then the ports a...A novel dual-band ISGW cavity filter with enhanced frequency selectivity is proposed in this paper by utilizing a multi-mode coupling topology.Its cavity is designed to control the number of modes,and then the ports are determined by analyzing the coupling relationship between these selected modes.By synthesizing the coupling matrix of the filter,a nonresonating node(NRN)structure is introduced to flexibly tune the frequency of modes,which gets a dualband and quad-band filtering response from a tri-band filter no the NRN.Furthermore,a frequency selective surface(FSS)has been newly designed as the upper surface of the cavity,which significantly improves the bad out-of-band suppression and frequency selectivity that often exists in most traditional cavity filter designs and measurements.The results show that its two center frequencies are f01=27.50 GHz and f02=32.92GHz,respectively.Compared with the dual-band filter that there is no the FSS metasurface,the out-of-band suppression level is improved from measured 5 dB to18 dB,and its finite transmission zero(FTZ)numbers is increased from measured 1 to 4 between the two designed bands.Compared with the tri-band and quadband filter,its passband bandwidth is expanded from measured 1.17%,1.14%,and 1.13% or 1.31%,1.50%,0.56%,and 0.57% to 1.71% and 1.87%.In addition,the filter has compact,small,and lightweight characteristics.展开更多
Product selectivity and reaction pathway are highly dependent on surface structure of heterogeneous catalysts.For vapor-phase hydrogenation of dimethyl oxalate(DMO),"EG route"(DMO→methyl glycolate(MG)ethyle...Product selectivity and reaction pathway are highly dependent on surface structure of heterogeneous catalysts.For vapor-phase hydrogenation of dimethyl oxalate(DMO),"EG route"(DMO→methyl glycolate(MG)ethylene glycol(EG)→ethanol(ET))and"MA route"(DMO→MG→methyl acetate(MA))were proposed over traditional Cu based catalysts and Mo-based or Fe-based catalysts,respectively.Herein,tunable yield of ET(93.7%)and MA(72.1%)were obtained through different reaction routes over WO_(x) modified Cu/SiO_(2) catalysts,and the corresponding reaction route was further proved by kinetic study and in-situ DRIFTS technology.Mechanistic studies demonstrated that H_(2) activation ability,acid density and Cu-WO_(x) interaction on the catalysts were tuned by regulating the surface W density,which resulted in the different reaction pathway and product selectivity.What's more,high yield of MA produced from DMO hydrogenation was firstly reported with the H_(2) pressure as low as 0.5 MPa.展开更多
The translation activity is a process of the interlinguistic transmission of information realized by the information encoding and decoding.Encoding and decoding,cognitive practices operated in objective contexts,are i...The translation activity is a process of the interlinguistic transmission of information realized by the information encoding and decoding.Encoding and decoding,cognitive practices operated in objective contexts,are inevitably of selectivity ascribing to the restriction of contextual reasons.The translator as the intermediary agent connects the original author(encoder)and the target readers(decoder),shouldering the dual duties of the decoder and the encoder,for which his subjectivity is irrevocably manipulated by the selectivity of encoding and decoding.展开更多
Copper-based catalysts for CO2 hydrogenation to methanol are supported on ZrO2 and CeO2,respectively.Reaction results at 3.0 MPa and temperatures between 200 and 300°C reveal that Cu catalysts supported on ZrO2 a...Copper-based catalysts for CO2 hydrogenation to methanol are supported on ZrO2 and CeO2,respectively.Reaction results at 3.0 MPa and temperatures between 200 and 300°C reveal that Cu catalysts supported on ZrO2 and CeO2 exhibit better activity and selectivity than pure Cu catalyst due to Cu-support(ZrO2 and CeO2)interaction.Combining the structural characterizations with in-situ diffuse reflectance infrared Fourier transform spectroscopy(in-situ DRIFTS),Cu/CeO2 shows the higher methanol selectivity due to the formation of main carbonates intermediates,which are closely related with the oxygen vacancies over Cu/CeO2.In contrast,bicarbonate and carboxyl species are observed on Cu/ZrO2,which originates from the hydroxyl groups presented on catalyst surfaces.Difference in CO2 adsorption intermediates results in the distinct methanol selectivity over the two catalysts.展开更多
This paper lays particular emphasis on pun's effectiveness and selectivity in English advertisements.The illustration and examples can help us understand the English advertisements well and foster our ability to a...This paper lays particular emphasis on pun's effectiveness and selectivity in English advertisements.The illustration and examples can help us understand the English advertisements well and foster our ability to appreciate the charm of English.展开更多
Propane dehydrogenation(PDH) provides an alternative route for producing propylene. Herein, we demonstrates that h-BN is a promising support of Pt-based catalysts for PDH. The Pt catalysts supported on h-BN were prepa...Propane dehydrogenation(PDH) provides an alternative route for producing propylene. Herein, we demonstrates that h-BN is a promising support of Pt-based catalysts for PDH. The Pt catalysts supported on h-BN were prepared by an impregnation method using Pt(NH_(3))_(4)(NO_(3))_(2) as metal precursors. It has been found that the Pt/BN catalyst undergoing calcination and reduction is highly stable in both PDH reaction and coke-burning regeneration, together with low coke deposition and outstanding propylene selectivity(99%). Detailed characterizations reveal that the high coke resistance and high propylene selectivity of the Pt/BN catalyst are derived not only from the absence of acidity on BN support, but also from the calcination-induced and reduction-adjusted strong metal-support interaction(SMSI) between Pt and BN, which causes the partial encapsulation of Pt particles by BO_(x) overlayers. The BO_(x) overlayers can block the low-coordinated Pt sites and constrain Pt particles into smaller ensembles, suppressing side reactions such as cracking and deep dehydrogenation. Moreover, the BO_(x) overlayers can effectively inhibit Pt sintering by the spatial isolation of Pt during periodic reaction-regeneration cycles. In this work, the catalyst support for PDH is expanded to nonoxide BN, and the understanding of SMSI between Pt and BN will provide rational design strategy for BN-based catalysts.展开更多
The chemical transformation of natural oils provides alternatives to limited fossil fuels and produces compounds with added value for the chemical industries.The selective deoxygenation of natural oils to diesel-range...The chemical transformation of natural oils provides alternatives to limited fossil fuels and produces compounds with added value for the chemical industries.The selective deoxygenation of natural oils to diesel-ranged hydrocarbons,bio-jet fuels,or fatty alcohols with controllable selectivity is especially attractive in natural oil feedstock biorefineries.This review presents recent progress in catalytic deoxygenation of natural oils or related model compounds(e.g.,fatty acids)to renewable liquid fuels(green diesel and bio-jet fuels)and valuable fatty alcohols(unsaturated and saturated fatty alcohols).Besides,it discusses and compares the existing and potential strategies to control the product selectivity over heterogeneous catalysts.Most research conducted and reviewed has only addressed the production of one category;therefore,a new integrative vision exploring how to direct the process toward fuel and/or chemicals is urgently needed.Thus,work conducted to date addressing the development of new catalysts and studying the influence of the reaction parameters(e.g.,temperature,time and hydrogen pressure)is summarized and critically discussed from a green and sustainable perspective using efficiency indicators(e.g.,yields,selectivity,turnover frequencies and catalysts lifetime).Special attention has been given to the chemical transformations occurring to identify key descriptors to tune the selectivity toward target products by manipulating the reaction conditions and the structures of the catalysts.Finally,the challenges and future research goals to develop novel and holistic natural oil biorefineries are proposed.As a result,this critical review provides the readership with appropriate information to selectively control the transformation of natural oils into either biofuels and/or value-added chemicals.This new flexible vision can help pave the wave to suit the present and future market needs.展开更多
Ammonia detection possesses great potential in atmosphere environmental protection,agriculture,industry,and rapid medical diagnosis.However,it still remains a great challenge to balance the sensitivity,selectivity,wor...Ammonia detection possesses great potential in atmosphere environmental protection,agriculture,industry,and rapid medical diagnosis.However,it still remains a great challenge to balance the sensitivity,selectivity,working temperature,and response/recovery speed.In this work,Berlin green(BG)framework is demonstrated as a highly promising sensing material for ammonia detection by both density functional theory simulation and experimental gas sensing investigation.Vacancy in BG framework offers abundant active sites for ammonia absorption,and the absorbed ammonia transfers sufficient electron to BG,arousing remarkable enhancement of resistance.Pristine BG framework shows remarkable response to ammonia at 50–110°C with the highest response at 80°C,which is jointly influenced by ammonia’s absorption onto BG surface and insertion into BG lattice.The sensing performance of BG can hardly be achieved at room temperature due to its high resistance.Introduction of conductive Ti3CN MXene overcomes the high resistance of pure BG framework,and the simply prepared BG/Ti3CN mixture shows high selectivity to ammonia at room temperature with satisfying response/recovery speed.展开更多
Surface properties （viz. surface area, basicity/base strength distribution, and crystal phases） of alkali metal doped CaO （alkali metal/Ca= 0.1 and 0.4） catalysts and their catalytic activity/selectivity in oxidat...Surface properties （viz. surface area, basicity/base strength distribution, and crystal phases） of alkali metal doped CaO （alkali metal/Ca= 0.1 and 0.4） catalysts and their catalytic activity/selectivity in oxidative coupling of methane （OCM） to higher hydrocarbons at different reaction conditions （viz. temperature, 700 and 750 ℃; CH4/O2 ratio, 4.0 and 8.0 and space velocity, 5140-20550 cm^3 ·g^-1·h^-1） have been investigated. The influence of catalyst calcination temperature on the activity/selectivity has also been investigated. The surface properties （viz. surface area, basicity/base strength distribution） and catalytic activity/selectivity of the alkali metal doped CaO catalysts are strongly influenced by the alkali metal promoter and its concentration in the alkali metal doped CaO catalysts. An addition of alkali metal promoter to CaO results in a large decrease in the surface area but a large increase in the surface basicity （strong basic sites） and the C2＋ selectivity and yield of the catalysts in the OCM process. The activity and selectivity are strongly influenced by the catalyst calcination temperature. No direct relationship between surface basicity and catalytic activity/selectivity has been observed. Among the alkali metal doped CaO catalysts, Na-CaO （Na/Ca = 0.1, before calcination） catalyst （calcined at 750 ℃）, showed best performance （C2＋ selectivity of 68.8% with 24.7% methane conversion）, whereas the poorest performance was shown by the Rb-CaO catalyst in the OCM process.展开更多
The SAPO-34 catalyst was fine-tuned with zinc cations through a straightforward template-assisted ion incorporation (TH) process, without the necessary template pre-removal and the preparation of NH4- SAPO-34 intermed...The SAPO-34 catalyst was fine-tuned with zinc cations through a straightforward template-assisted ion incorporation (TH) process, without the necessary template pre-removal and the preparation of NH4- SAPO-34 intermediate, which is more facile, efficient and cost-effective than the conventional ion exchange process. The template-assisted zinc cations incorporated SAPO-34 catalysts were characterized by XRD, XRF, N2 adsorption-desorption, XPS, SEM, EDX,NMR, respectively. Enhanced selectivity to ethylene and ratio of ethylene to propylene in MTO reaction are observed over the zinc cations modified SAPO-34 catalysts, due to the facilitated formation of lower methylbenzenes that favour the ethylene gen eration, as well as the increased diffusion hindrance originated from the zinc cations incorporation and the facil让ated generation of aromatics compound.展开更多
Bimetallic Fe-Mn nano catalysts supported on carbon nanotubes(CNTs) were prepared using microemulsion technique with water-to-surfactant ratios of 0.4-1.6. The nano catalysts were extensively characterized by differen...Bimetallic Fe-Mn nano catalysts supported on carbon nanotubes(CNTs) were prepared using microemulsion technique with water-to-surfactant ratios of 0.4-1.6. The nano catalysts were extensively characterized by different methods and their activity and selectivity in Fischer-Tropsch synthesis(FTS) have been assessed in a fixed-bed microreactor. The physicochemical properties and performance of the nanocatalysts were compared with the catalyst prepared by impregnation method. Very narrow particle size distribution has been produced by the microemulsion technique at relatively high loading of active metal. TEM images showed that small metal nano particles in the range of 3–7 nm were not only confined inside the CNTs but also located on the outer surface of the CNTs. Using microemulsion technique with water to surfactant ratio of0.4 decreased the average iron particle sizes to 5.1 nm. The reduction percentage and dispersion percentage were almost doubled. Activity and selectivity were found to be dependent on the catalyst preparation method and average iron particle size. CO conversion and FTS rate increased from 49.1% to 71.0% and 0.144 to 0.289 gHC/(gcat h), respectively. While the WGS rate decreased from 0.097 to 0.056 gCO2/(gcat h). C5+liquid hydrocarbons selectivity decreased slightly and olefins selectivity almost doubled.展开更多
Effects of vanadium on light olefins selectivity of FCC catalysts were investigated with vanadium having different oxidation numbers （hereinafter abbreviated as Oxnum）. Molecular modeling studies showed that vanadiu...Effects of vanadium on light olefins selectivity of FCC catalysts were investigated with vanadium having different oxidation numbers （hereinafter abbreviated as Oxnum）. Molecular modeling studies showed that vanadium with low Oxnum could affect the chemical conversion of large-size hydrocarbon molecules. However, the vanadium deposited on equilibrium catalyst bad high Oxnum because of the oxidation reaction taking place in the regenerator, so an activation method to reduce vanadium Oxnum named ＂selective activation＂ was introduced. It was proved by means of Electron Paramagnetic Resonance （EPR） and Temperature-Programmed Reduction （TPR） methods that the vanadium Oxnum was decreased, when the catalyst was activated. The molecular modeling studies are consistent well with the lab evaluation results. The light olefins selectivity of activated equilibrium catalysts was better than that achieved by the inactivated catalysts. Similar results were observed with the lab vanadium-contaminated catalyst. The light olefins selectivity of the catalyst was optimized when the vanadium Oxnum was close to 2 （VO）.展开更多
Structure-performance relationship is a complex issue in iron-catalyzed Fischer-Tropsch synthesis,and it is not easy to elucidate it by experimental investigations.First-principle calculation is a powerful method for ...Structure-performance relationship is a complex issue in iron-catalyzed Fischer-Tropsch synthesis,and it is not easy to elucidate it by experimental investigations.First-principle calculation is a powerful method for explaining experimental results and guiding catalyst design.In this study,we investigated the reaction mechanisms of CH_(4)formation and C-C coupling on fourχ-Fe_(5)C_(2)surfaces and established the kinetic equations to compare the rates of CH_(4)formation and C_(1)+C_(1)coupling reactions and determine the CH_(4)/C_(2+)selectivity.The results show that the geometry of theχ-Fe_(5)C_(2)surfaces has little effect on the formation rate of CH_(4);however,the C_(1)+C_(1)coupling reactions are significantly affected by the surface geometry.The C_(1)+C_(1)coupling reaction rates on the terraced-like(510)and(021)surfaces are much higher than those on the stepped-like(001)and(100)surfaces.Based on these results,we established a Brùnsted-Evans-Polanyi(BEP)relationship between the effective barrier difference for CH_(4)formation and C_(1)+C_(1)coupling(ΔE_(eff))and the adsorption energy of C+4H(ΔE_(C+4H))onχ-Fe_(5)C_(2)surfaces.ΔE_(C+4H)can be used as a descriptor for CH_(4)/C_(2+)selectivity on different surfaces ofχ-Fe_(5)C_(2).展开更多
A Ni-La/SiO2 catalyst was prepared through the incipient wetness impregnation method and tested in the oxidative dehydrogenation of ethane （ODHE） with CO2. The fresh and used catalysts were characterized by XRD and ...A Ni-La/SiO2 catalyst was prepared through the incipient wetness impregnation method and tested in the oxidative dehydrogenation of ethane （ODHE） with CO2. The fresh and used catalysts were characterized by XRD and SEM techniques. The Ni-La/SiO2 catalyst exhibited catalytic activity for the oxidative dehydrogenation of ethane, but with low ethylene selectivity in the absence of methane. The selectivity to ethylene increased with increasing molar ratio of methane in the feed. The carbon deposited on the catalyst surface in the sole ODHE with CO2 was mainly inert carbon, while much more filamentous carbon was formed in the presence of methane. The filamentous carbon was easy to be removed by CO2, which might play a role in improving the conversion of ethane to ethylene. The introduction of methane might affect the equilibrium of the CO2 reforming of ethane and the ODHE with CO2. As a consequence, the synthesis gas produced from CO2 reforming of methane partly inhibited the reaction of ethane and promoted the ODHE with CO2, thus increasing the selectivity of ethylene.展开更多
Hydrogen peroxide(H_(2)O_(2))is one of the most important chemicals,which are commonly used in the paper and pulp industry,water purification and environmental protection[1-3].Most of the commercial available H_(2)O_(...Hydrogen peroxide(H_(2)O_(2))is one of the most important chemicals,which are commonly used in the paper and pulp industry,water purification and environmental protection[1-3].Most of the commercial available H_(2)O_(2) is produced by the anthraquinone oxidation process,which is environment unfriendly.展开更多
Fischer-Tropsch synthesis(FTS) is the key step in converting syngas into clean fuels. Traditional supported catalysts for FTS are problematic because the active metal crystalline size is positively related to metal lo...Fischer-Tropsch synthesis(FTS) is the key step in converting syngas into clean fuels. Traditional supported catalysts for FTS are problematic because the active metal crystalline size is positively related to metal loading. Therefore, increasing active metal loading may reduce the cobalt time yield(CTY) since a high CTY is usually obtained when the Co size is 8 nm. Here, a ZIF-67(Zeolitic imidazolate framework-67) with a MOF(Metal organic framework) structure is used as a precursor to prepare the Co@C catalyst with not only high cobalt loading(55.6 wt%) but also with a small cobalt crystal size(as small as 8.6 nm). Coreshell Co@C@SiO2-X catalysts with different SiO2 shell thicknesses were successfully prepared by coating different amounts of TEOS on the outer surface of Co@C to modify product selectivity. Compared with40 wt% Co/SiO2 catalyst, core-shell Co@C@SiO2-X catalysts exhibited improved FTS performance. Furthermore, different gaseous hourly space velocities(GHSVs) were used to obtain CO conversion at similar levels to compare CTY and the turnover frequency(TOF). Among the catalysts, the Co@C@SiO2-1 catalyst, with its better mass transfer ability and suitable hydrophilic property, presented the highest TOF(9.75 × 10-3 s-1) and lowest CH4 selectivity(9.75%). In addition, heavy hydrocarbons were effectively suppressed with the increase in shell thickness due to the increased mass transfer resistance.展开更多
Enhancing ion conductance and controlling transport pathway in organic electrolyte could be used to modulate ionic kinetics to handle signals. In a Pt/Poly(3-hexylthiophene-2,5-diyl)/Polyethylene?Li CF3SO3/Pt hetero-j...Enhancing ion conductance and controlling transport pathway in organic electrolyte could be used to modulate ionic kinetics to handle signals. In a Pt/Poly(3-hexylthiophene-2,5-diyl)/Polyethylene?Li CF3SO3/Pt hetero-junction, the electrolyte layer handled at high temperature showed nano-fiber microstructures accompanied with greatly improved salt solubility. Ions with high mobility were confined in the nano-fibrous channels leading to the semiconducting polymer layer,which is favorable for modulating dynamic doping at the semiconducting polymer/electrolyte interface by pulse frequency.Such a device realized synaptic-like frequency selectivity, i.e., depression at low frequency stimulation but potentiation at high-frequency stimulation.展开更多
We report near-zero crossover for vanadium cross-permeation through single-layer graphene immobilized at the interface of two Nafion?polymer electrolyte membranes.Vanadium ion diffusion and migration,including proton ...We report near-zero crossover for vanadium cross-permeation through single-layer graphene immobilized at the interface of two Nafion?polymer electrolyte membranes.Vanadium ion diffusion and migration,including proton mobility through membrane composites,were studied with and without graphene under diffusion and migration conditions.Single-layer graphene was found to effectively inhibit vanadium ion diffusion and migration under specific conditions.The single-layer graphene composites also enabled remarkable ion transmission selectivity improvements over pure Nafion membranes,with proton transport being four orders of magnitude faster than vanadium ion transport.Resistivity values of 0.02±0.005Ωcm^(2) for proton and 223±4Ωcm^(2) for vanadium ion through single atomic layer graphene are reported.This high selectivity may have significant impact on flow battery applications or for other electrochemical devices where proton conductivity is required,and transport of other species is detrimental.Our results emphasize that crossover may be essentially completely eliminated in some cases,enabling for greatly improved operational viability.展开更多
It is commonly realized that polydispersity may significantly affect the surface modification properties of polymer brush systems. In light of this, we systematically study morphologies of bidisperse polyelectrolyte b...It is commonly realized that polydispersity may significantly affect the surface modification properties of polymer brush systems. In light of this, we systematically study morphologies of bidisperse polyelectrolyte brush grafted onto a spherical nanocolloid in the presence of trivalent counterions using molecular dynamics simulations. Via varying polydispersity, grafting density, and solvent selectivity, the effects of electrostatic correlation and excluded volume are focused, and rich phase behaviors of binary mixed polyelectrolyte brush are predicted, including a variety of pinned-patch morphologies at low grafting density and micelle-like structures at high grafting density. To pinpoint the mechanism of surface structure formation, the shape factor of two species of polyelectrolyte chains and the pair correlation function between monomers from different polyelectrolyte ligands are analyzed carefully. Also, electrostatic correlations, manifested as the bridging through trivalent counterions, are examined by identifying four states of trivalent counterions. Our simulation results may be useful for designing smart stimuli-responsive materials based on mixed polyelectrolyte coated surfaces.展开更多
We report on the investigation of the origin of high oxide to nitride polishing selectivity of ceria-based slurry in the presence of picolinic acid. The oxide to nitride removal selectivity of the ceria slurry with pi...We report on the investigation of the origin of high oxide to nitride polishing selectivity of ceria-based slurry in the presence of picolinic acid. The oxide to nitride removal selectivity of the ceria slurry with picolinic acid is as high as 76.6 in the chemical mechanical polishing. By using zeta potential analyzer, particle size analyzer, horizon profilometer, thermogravimetric analysis and Fourier transform infrared spectroscopy, the pre- and the post-polished wafer surfaces as well as the pre- and the post-used ceria-based slurries are compared. Possible mechanism of high oxide to nitride selectivity with using ceria-based slurry with picolinic acid is discussed.展开更多
基金supported by the National key research and development program of China(No.2021YFB2900401)by the National Natural Science Foundation of China(No.61861046)+1 种基金the key Natural Science Foundation of shenzhen(No.JCYJ20220818102209020)the key research and development program of shenzhen(No.ZDSYS20210623091807023)。
文摘A novel dual-band ISGW cavity filter with enhanced frequency selectivity is proposed in this paper by utilizing a multi-mode coupling topology.Its cavity is designed to control the number of modes,and then the ports are determined by analyzing the coupling relationship between these selected modes.By synthesizing the coupling matrix of the filter,a nonresonating node(NRN)structure is introduced to flexibly tune the frequency of modes,which gets a dualband and quad-band filtering response from a tri-band filter no the NRN.Furthermore,a frequency selective surface(FSS)has been newly designed as the upper surface of the cavity,which significantly improves the bad out-of-band suppression and frequency selectivity that often exists in most traditional cavity filter designs and measurements.The results show that its two center frequencies are f01=27.50 GHz and f02=32.92GHz,respectively.Compared with the dual-band filter that there is no the FSS metasurface,the out-of-band suppression level is improved from measured 5 dB to18 dB,and its finite transmission zero(FTZ)numbers is increased from measured 1 to 4 between the two designed bands.Compared with the tri-band and quadband filter,its passband bandwidth is expanded from measured 1.17%,1.14%,and 1.13% or 1.31%,1.50%,0.56%,and 0.57% to 1.71% and 1.87%.In addition,the filter has compact,small,and lightweight characteristics.
基金supported by National Natural Science Foundation of China (No.22102147 and 22002151)State Key Laboratory of Chemical Engineering (No.SKL-ChE-22A02)+2 种基金Zhejiang Provincial Natural Science Foundation of China under Grant No.LQ21B030009the Strategic Priority Research Program of the Chinese Academy of Sciences (No.XDA29050300)Qinchuang Yuan high-level innovation and entrepreneurship talents implementing project (No.QCYRCXM-2022-177)。
文摘Product selectivity and reaction pathway are highly dependent on surface structure of heterogeneous catalysts.For vapor-phase hydrogenation of dimethyl oxalate(DMO),"EG route"(DMO→methyl glycolate(MG)ethylene glycol(EG)→ethanol(ET))and"MA route"(DMO→MG→methyl acetate(MA))were proposed over traditional Cu based catalysts and Mo-based or Fe-based catalysts,respectively.Herein,tunable yield of ET(93.7%)and MA(72.1%)were obtained through different reaction routes over WO_(x) modified Cu/SiO_(2) catalysts,and the corresponding reaction route was further proved by kinetic study and in-situ DRIFTS technology.Mechanistic studies demonstrated that H_(2) activation ability,acid density and Cu-WO_(x) interaction on the catalysts were tuned by regulating the surface W density,which resulted in the different reaction pathway and product selectivity.What's more,high yield of MA produced from DMO hydrogenation was firstly reported with the H_(2) pressure as low as 0.5 MPa.
文摘The translation activity is a process of the interlinguistic transmission of information realized by the information encoding and decoding.Encoding and decoding,cognitive practices operated in objective contexts,are inevitably of selectivity ascribing to the restriction of contextual reasons.The translator as the intermediary agent connects the original author(encoder)and the target readers(decoder),shouldering the dual duties of the decoder and the encoder,for which his subjectivity is irrevocably manipulated by the selectivity of encoding and decoding.
基金financially supported by the National Natural Science Foundation of China (21577014, 21876019, 21825203, 21688102)Programme of Introducing Talents of Discipline to Universities (B13012)the fund of the State Key Laboratory of Catalysis in DICP (Y401010502)
文摘Copper-based catalysts for CO2 hydrogenation to methanol are supported on ZrO2 and CeO2,respectively.Reaction results at 3.0 MPa and temperatures between 200 and 300°C reveal that Cu catalysts supported on ZrO2 and CeO2 exhibit better activity and selectivity than pure Cu catalyst due to Cu-support(ZrO2 and CeO2)interaction.Combining the structural characterizations with in-situ diffuse reflectance infrared Fourier transform spectroscopy(in-situ DRIFTS),Cu/CeO2 shows the higher methanol selectivity due to the formation of main carbonates intermediates,which are closely related with the oxygen vacancies over Cu/CeO2.In contrast,bicarbonate and carboxyl species are observed on Cu/ZrO2,which originates from the hydroxyl groups presented on catalyst surfaces.Difference in CO2 adsorption intermediates results in the distinct methanol selectivity over the two catalysts.
文摘This paper lays particular emphasis on pun's effectiveness and selectivity in English advertisements.The illustration and examples can help us understand the English advertisements well and foster our ability to appreciate the charm of English.
基金financially supported by the National Natural Science Foundation of China(21273049,22172037)the Guangdong Basic and Applied Basic Research Foundation(2021A1515010014)+1 种基金the Science and Technology Program of Guangzhou(201904010023)the CAS Key Laboratory of Renewable Energy(E029kf0901)。
文摘Propane dehydrogenation(PDH) provides an alternative route for producing propylene. Herein, we demonstrates that h-BN is a promising support of Pt-based catalysts for PDH. The Pt catalysts supported on h-BN were prepared by an impregnation method using Pt(NH_(3))_(4)(NO_(3))_(2) as metal precursors. It has been found that the Pt/BN catalyst undergoing calcination and reduction is highly stable in both PDH reaction and coke-burning regeneration, together with low coke deposition and outstanding propylene selectivity(99%). Detailed characterizations reveal that the high coke resistance and high propylene selectivity of the Pt/BN catalyst are derived not only from the absence of acidity on BN support, but also from the calcination-induced and reduction-adjusted strong metal-support interaction(SMSI) between Pt and BN, which causes the partial encapsulation of Pt particles by BO_(x) overlayers. The BO_(x) overlayers can block the low-coordinated Pt sites and constrain Pt particles into smaller ensembles, suppressing side reactions such as cracking and deep dehydrogenation. Moreover, the BO_(x) overlayers can effectively inhibit Pt sintering by the spatial isolation of Pt during periodic reaction-regeneration cycles. In this work, the catalyst support for PDH is expanded to nonoxide BN, and the understanding of SMSI between Pt and BN will provide rational design strategy for BN-based catalysts.
基金financially supported by the National Natural Science Foundation of China (No.21536007)the 111 Project (B17030)+1 种基金support from China Scholarship Council (CSC No.202006240156)the Spanish Ministry of Science,Innovation and Universities for the Juan de la Cierva (JdC)fellowships (Grant Numbers FJCI-2016-30847 and IJC2018-037110-I)awarded.
文摘The chemical transformation of natural oils provides alternatives to limited fossil fuels and produces compounds with added value for the chemical industries.The selective deoxygenation of natural oils to diesel-ranged hydrocarbons,bio-jet fuels,or fatty alcohols with controllable selectivity is especially attractive in natural oil feedstock biorefineries.This review presents recent progress in catalytic deoxygenation of natural oils or related model compounds(e.g.,fatty acids)to renewable liquid fuels(green diesel and bio-jet fuels)and valuable fatty alcohols(unsaturated and saturated fatty alcohols).Besides,it discusses and compares the existing and potential strategies to control the product selectivity over heterogeneous catalysts.Most research conducted and reviewed has only addressed the production of one category;therefore,a new integrative vision exploring how to direct the process toward fuel and/or chemicals is urgently needed.Thus,work conducted to date addressing the development of new catalysts and studying the influence of the reaction parameters(e.g.,temperature,time and hydrogen pressure)is summarized and critically discussed from a green and sustainable perspective using efficiency indicators(e.g.,yields,selectivity,turnover frequencies and catalysts lifetime).Special attention has been given to the chemical transformations occurring to identify key descriptors to tune the selectivity toward target products by manipulating the reaction conditions and the structures of the catalysts.Finally,the challenges and future research goals to develop novel and holistic natural oil biorefineries are proposed.As a result,this critical review provides the readership with appropriate information to selectively control the transformation of natural oils into either biofuels and/or value-added chemicals.This new flexible vision can help pave the wave to suit the present and future market needs.
基金The research was supported by the National Natural Science Foundation of China(Grant Nos.61435010,61675135,and 62005177)the National Natural Science Foundation for Young Scientists of China(Grant No.61905161)the Science and Technology Innovation Commission of Shenzhen(JCYJ20190808142415003).Authors also acknowledge the support from Instrumental Analysis Center of Shenzhen University(Xili Campus).
文摘Ammonia detection possesses great potential in atmosphere environmental protection,agriculture,industry,and rapid medical diagnosis.However,it still remains a great challenge to balance the sensitivity,selectivity,working temperature,and response/recovery speed.In this work,Berlin green(BG)framework is demonstrated as a highly promising sensing material for ammonia detection by both density functional theory simulation and experimental gas sensing investigation.Vacancy in BG framework offers abundant active sites for ammonia absorption,and the absorbed ammonia transfers sufficient electron to BG,arousing remarkable enhancement of resistance.Pristine BG framework shows remarkable response to ammonia at 50–110°C with the highest response at 80°C,which is jointly influenced by ammonia’s absorption onto BG surface and insertion into BG lattice.The sensing performance of BG can hardly be achieved at room temperature due to its high resistance.Introduction of conductive Ti3CN MXene overcomes the high resistance of pure BG framework,and the simply prepared BG/Ti3CN mixture shows high selectivity to ammonia at room temperature with satisfying response/recovery speed.
文摘Surface properties （viz. surface area, basicity/base strength distribution, and crystal phases） of alkali metal doped CaO （alkali metal/Ca= 0.1 and 0.4） catalysts and their catalytic activity/selectivity in oxidative coupling of methane （OCM） to higher hydrocarbons at different reaction conditions （viz. temperature, 700 and 750 ℃; CH4/O2 ratio, 4.0 and 8.0 and space velocity, 5140-20550 cm^3 ·g^-1·h^-1） have been investigated. The influence of catalyst calcination temperature on the activity/selectivity has also been investigated. The surface properties （viz. surface area, basicity/base strength distribution） and catalytic activity/selectivity of the alkali metal doped CaO catalysts are strongly influenced by the alkali metal promoter and its concentration in the alkali metal doped CaO catalysts. An addition of alkali metal promoter to CaO results in a large decrease in the surface area but a large increase in the surface basicity （strong basic sites） and the C2＋ selectivity and yield of the catalysts in the OCM process. The activity and selectivity are strongly influenced by the catalyst calcination temperature. No direct relationship between surface basicity and catalytic activity/selectivity has been observed. Among the alkali metal doped CaO catalysts, Na-CaO （Na/Ca = 0.1, before calcination） catalyst （calcined at 750 ℃）, showed best performance （C2＋ selectivity of 68.8% with 24.7% methane conversion）, whereas the poorest performance was shown by the Rb-CaO catalyst in the OCM process.
基金the National Natural Science Foundation of China(21603223,91745109,91545104,21473182,91334205)the Youth Innovation Promotion Association of the Chinese Academy of Sciences(2014165)for financial support
文摘The SAPO-34 catalyst was fine-tuned with zinc cations through a straightforward template-assisted ion incorporation (TH) process, without the necessary template pre-removal and the preparation of NH4- SAPO-34 intermediate, which is more facile, efficient and cost-effective than the conventional ion exchange process. The template-assisted zinc cations incorporated SAPO-34 catalysts were characterized by XRD, XRF, N2 adsorption-desorption, XPS, SEM, EDX,NMR, respectively. Enhanced selectivity to ethylene and ratio of ethylene to propylene in MTO reaction are observed over the zinc cations modified SAPO-34 catalysts, due to the facilitated formation of lower methylbenzenes that favour the ethylene gen eration, as well as the increased diffusion hindrance originated from the zinc cations incorporation and the facil让ated generation of aromatics compound.
文摘Bimetallic Fe-Mn nano catalysts supported on carbon nanotubes(CNTs) were prepared using microemulsion technique with water-to-surfactant ratios of 0.4-1.6. The nano catalysts were extensively characterized by different methods and their activity and selectivity in Fischer-Tropsch synthesis(FTS) have been assessed in a fixed-bed microreactor. The physicochemical properties and performance of the nanocatalysts were compared with the catalyst prepared by impregnation method. Very narrow particle size distribution has been produced by the microemulsion technique at relatively high loading of active metal. TEM images showed that small metal nano particles in the range of 3–7 nm were not only confined inside the CNTs but also located on the outer surface of the CNTs. Using microemulsion technique with water to surfactant ratio of0.4 decreased the average iron particle sizes to 5.1 nm. The reduction percentage and dispersion percentage were almost doubled. Activity and selectivity were found to be dependent on the catalyst preparation method and average iron particle size. CO conversion and FTS rate increased from 49.1% to 71.0% and 0.144 to 0.289 gHC/(gcat h), respectively. While the WGS rate decreased from 0.097 to 0.056 gCO2/(gcat h). C5+liquid hydrocarbons selectivity decreased slightly and olefins selectivity almost doubled.
文摘Effects of vanadium on light olefins selectivity of FCC catalysts were investigated with vanadium having different oxidation numbers （hereinafter abbreviated as Oxnum）. Molecular modeling studies showed that vanadium with low Oxnum could affect the chemical conversion of large-size hydrocarbon molecules. However, the vanadium deposited on equilibrium catalyst bad high Oxnum because of the oxidation reaction taking place in the regenerator, so an activation method to reduce vanadium Oxnum named ＂selective activation＂ was introduced. It was proved by means of Electron Paramagnetic Resonance （EPR） and Temperature-Programmed Reduction （TPR） methods that the vanadium Oxnum was decreased, when the catalyst was activated. The molecular modeling studies are consistent well with the lab evaluation results. The light olefins selectivity of activated equilibrium catalysts was better than that achieved by the inactivated catalysts. Similar results were observed with the lab vanadium-contaminated catalyst. The light olefins selectivity of the catalyst was optimized when the vanadium Oxnum was close to 2 （VO）.
基金financially supported by the Natural Science Foundation of China(21922803 and 21776077)the Program for the Professor of Special Appointment(Eastern Scholar)at Shanghai Institutions of Higher Learning+1 种基金the State Key Laboratory of Organic-Inorganic Composites(oic-201801007)the Open Project of State Key Laboratory of Chemical Engineering(SKLChe-15C03)。
文摘Structure-performance relationship is a complex issue in iron-catalyzed Fischer-Tropsch synthesis,and it is not easy to elucidate it by experimental investigations.First-principle calculation is a powerful method for explaining experimental results and guiding catalyst design.In this study,we investigated the reaction mechanisms of CH_(4)formation and C-C coupling on fourχ-Fe_(5)C_(2)surfaces and established the kinetic equations to compare the rates of CH_(4)formation and C_(1)+C_(1)coupling reactions and determine the CH_(4)/C_(2+)selectivity.The results show that the geometry of theχ-Fe_(5)C_(2)surfaces has little effect on the formation rate of CH_(4);however,the C_(1)+C_(1)coupling reactions are significantly affected by the surface geometry.The C_(1)+C_(1)coupling reaction rates on the terraced-like(510)and(021)surfaces are much higher than those on the stepped-like(001)and(100)surfaces.Based on these results,we established a Brùnsted-Evans-Polanyi(BEP)relationship between the effective barrier difference for CH_(4)formation and C_(1)+C_(1)coupling(ΔE_(eff))and the adsorption energy of C+4H(ΔE_(C+4H))onχ-Fe_(5)C_(2)surfaces.ΔE_(C+4H)can be used as a descriptor for CH_(4)/C_(2+)selectivity on different surfaces ofχ-Fe_(5)C_(2).
基金supported by the NNSFC (Nos. 20976109, 21021001)the Special Research Foundation of Doctoral Education of China (No.20090181110046)
文摘A Ni-La/SiO2 catalyst was prepared through the incipient wetness impregnation method and tested in the oxidative dehydrogenation of ethane （ODHE） with CO2. The fresh and used catalysts were characterized by XRD and SEM techniques. The Ni-La/SiO2 catalyst exhibited catalytic activity for the oxidative dehydrogenation of ethane, but with low ethylene selectivity in the absence of methane. The selectivity to ethylene increased with increasing molar ratio of methane in the feed. The carbon deposited on the catalyst surface in the sole ODHE with CO2 was mainly inert carbon, while much more filamentous carbon was formed in the presence of methane. The filamentous carbon was easy to be removed by CO2, which might play a role in improving the conversion of ethane to ethylene. The introduction of methane might affect the equilibrium of the CO2 reforming of ethane and the ODHE with CO2. As a consequence, the synthesis gas produced from CO2 reforming of methane partly inhibited the reaction of ethane and promoted the ODHE with CO2, thus increasing the selectivity of ethylene.
基金supported by the NSF for Distinguished Young Scholars of Fujian Province(Grant no.2017 J07004)。
文摘Hydrogen peroxide(H_(2)O_(2))is one of the most important chemicals,which are commonly used in the paper and pulp industry,water purification and environmental protection[1-3].Most of the commercial available H_(2)O_(2) is produced by the anthraquinone oxidation process,which is environment unfriendly.
基金financial support from the National Natural Science Foundation of China (21506154)the Program of Introducing Talents of Discipline to Universities (B06006)。
文摘Fischer-Tropsch synthesis(FTS) is the key step in converting syngas into clean fuels. Traditional supported catalysts for FTS are problematic because the active metal crystalline size is positively related to metal loading. Therefore, increasing active metal loading may reduce the cobalt time yield(CTY) since a high CTY is usually obtained when the Co size is 8 nm. Here, a ZIF-67(Zeolitic imidazolate framework-67) with a MOF(Metal organic framework) structure is used as a precursor to prepare the Co@C catalyst with not only high cobalt loading(55.6 wt%) but also with a small cobalt crystal size(as small as 8.6 nm). Coreshell Co@C@SiO2-X catalysts with different SiO2 shell thicknesses were successfully prepared by coating different amounts of TEOS on the outer surface of Co@C to modify product selectivity. Compared with40 wt% Co/SiO2 catalyst, core-shell Co@C@SiO2-X catalysts exhibited improved FTS performance. Furthermore, different gaseous hourly space velocities(GHSVs) were used to obtain CO conversion at similar levels to compare CTY and the turnover frequency(TOF). Among the catalysts, the Co@C@SiO2-1 catalyst, with its better mass transfer ability and suitable hydrophilic property, presented the highest TOF(9.75 × 10-3 s-1) and lowest CH4 selectivity(9.75%). In addition, heavy hydrocarbons were effectively suppressed with the increase in shell thickness due to the increased mass transfer resistance.
基金supported by National Natural Science foundation of China (Grant Nos. 51371103 and 51231004)National Basic Research Program of China (Grant No. 2010CB832905)+1 种基金National Hi-tech (R&D) Project of China (Grant Nos. 2012AA03A706, 2013AA030801)the Research Project of Chinese Ministry of Education (No. 113007A)
文摘Enhancing ion conductance and controlling transport pathway in organic electrolyte could be used to modulate ionic kinetics to handle signals. In a Pt/Poly(3-hexylthiophene-2,5-diyl)/Polyethylene?Li CF3SO3/Pt hetero-junction, the electrolyte layer handled at high temperature showed nano-fiber microstructures accompanied with greatly improved salt solubility. Ions with high mobility were confined in the nano-fibrous channels leading to the semiconducting polymer layer,which is favorable for modulating dynamic doping at the semiconducting polymer/electrolyte interface by pulse frequency.Such a device realized synaptic-like frequency selectivity, i.e., depression at low frequency stimulation but potentiation at high-frequency stimulation.
文摘We report near-zero crossover for vanadium cross-permeation through single-layer graphene immobilized at the interface of two Nafion?polymer electrolyte membranes.Vanadium ion diffusion and migration,including proton mobility through membrane composites,were studied with and without graphene under diffusion and migration conditions.Single-layer graphene was found to effectively inhibit vanadium ion diffusion and migration under specific conditions.The single-layer graphene composites also enabled remarkable ion transmission selectivity improvements over pure Nafion membranes,with proton transport being four orders of magnitude faster than vanadium ion transport.Resistivity values of 0.02±0.005Ωcm^(2) for proton and 223±4Ωcm^(2) for vanadium ion through single atomic layer graphene are reported.This high selectivity may have significant impact on flow battery applications or for other electrochemical devices where proton conductivity is required,and transport of other species is detrimental.Our results emphasize that crossover may be essentially completely eliminated in some cases,enabling for greatly improved operational viability.
基金supported by the Fundamental Research Funds for the Central Universities of China (Grant No. 3122020080)。
文摘It is commonly realized that polydispersity may significantly affect the surface modification properties of polymer brush systems. In light of this, we systematically study morphologies of bidisperse polyelectrolyte brush grafted onto a spherical nanocolloid in the presence of trivalent counterions using molecular dynamics simulations. Via varying polydispersity, grafting density, and solvent selectivity, the effects of electrostatic correlation and excluded volume are focused, and rich phase behaviors of binary mixed polyelectrolyte brush are predicted, including a variety of pinned-patch morphologies at low grafting density and micelle-like structures at high grafting density. To pinpoint the mechanism of surface structure formation, the shape factor of two species of polyelectrolyte chains and the pair correlation function between monomers from different polyelectrolyte ligands are analyzed carefully. Also, electrostatic correlations, manifested as the bridging through trivalent counterions, are examined by identifying four states of trivalent counterions. Our simulation results may be useful for designing smart stimuli-responsive materials based on mixed polyelectrolyte coated surfaces.
基金supported by the Center for Advanced Materials Processing (CAMP) at Clarkson Universitythe National Integrate Circuit Research Program of China (Grant No. 2009ZX02023-3)+3 种基金the National Basic Research Program of China (GrantNos. 2007CB935400,2010CB934300 and 2006CB302700)the National High Technology Development Program of China (GrantNo. 2008AA031402)the Science and Technology Council of Shanghai,China (Grant Nos. 08DZ2200700,08JC1421700 and09QH1402600)the Chinese Academy of Sciences Visiting Professorship for Senior International Scientists
文摘We report on the investigation of the origin of high oxide to nitride polishing selectivity of ceria-based slurry in the presence of picolinic acid. The oxide to nitride removal selectivity of the ceria slurry with picolinic acid is as high as 76.6 in the chemical mechanical polishing. By using zeta potential analyzer, particle size analyzer, horizon profilometer, thermogravimetric analysis and Fourier transform infrared spectroscopy, the pre- and the post-polished wafer surfaces as well as the pre- and the post-used ceria-based slurries are compared. Possible mechanism of high oxide to nitride selectivity with using ceria-based slurry with picolinic acid is discussed.
