We present a comparison of data obtained during testing of lightning protective system of a residential structure in rocket-triggered lightning experiment at the International Center for Lightning Research and Testing...We present a comparison of data obtained during testing of lightning protective system of a residential structure in rocket-triggered lightning experiment at the International Center for Lightning Research and Testing(ICLRT)at Camp Blanding,Florida,and current surge generator experiment at Rzeszow University of Technology in Poland.Three different configurations of LPS were tested in Poland with the dc grounding resistances of the entire system 4.09 Ω(LPS 1a),1.65 Ω(LPS 1b),and 2.88 Ω(LPS 2).For LPS 1a with three ground rods the value of the peak current entering the electrical circuit neutral was about 56% of the injected current peak,and for LPS 1b with two additional ground rods and two 5 m long buried horizontal conductors it was about 16%.For LPS 2 with five ground rods interconnected by a buried loop conductor this ratio was 21%.The current waveshapes in the ground rods differed from the injected current waveshapes and the current waveshapes in other parts of the test system,especially,for poorer-grounding LPS 1a.The surge-generator results are consistent with those of triggered-lightning experiments at Camp Blanding,Florida(DeCarlo et al.,2008 [2]).展开更多
It is one of the most effective ways to use laboratory long air gap discharges for investigating the fundamental process involved in the lightning strike.During the 1960s and the 1970s,the electro-geometrical method(E...It is one of the most effective ways to use laboratory long air gap discharges for investigating the fundamental process involved in the lightning strike.During the 1960s and the 1970s,the electro-geometrical method(EGM)and the rolling sphere method were developed base on the breakdowncharacteristics of negative long spark discharges,which have been widely used to design the lightning shielding system of transmission lines and structures.In recent years,the scale of the power facilities is increased dramatically with the rising of power grid's voltage level.The impact of upward connecting leader launched from those large-scale facilities on the lightning shielding performance cannot be neglected;otherwise,the validity of the EGM in the lightning shielding design of EHV and UHV transmission lines will be challenged.The research evolutions on the lightning striking distance,the lightning simulation experiments and the positive upward connecting leader process by using laboratory long sparks are reviewed and discussed in this paper.展开更多
In recent years,along with the rapid expansion of power grids,the increasing complication of grid structures,and the development of smart grids and energy technologies,the lightning protection of power grids becomes i...In recent years,along with the rapid expansion of power grids,the increasing complication of grid structures,and the development of smart grids and energy technologies,the lightning protection of power grids becomes increasingly prominent.Power grids of China have acquired significant achievements on lightning protection technologies,which are reviewed in this paper.A technical route of lightning protection is introduced in detail; it allows us to find problems through detection and measurement of lightning,to analyze problems through evaluation and simulation of lightning,to solve problems through lightning protection measures,and to prevent problems through hazard risk warning of lightning.Following the route,the technical breakthroughs of these four aspects in China are presented,including the chinese lightning detection network(CLDN),natural lightning observations,lightning faults detection at transmission lines,lightning current measurements,progresses in lightning distribution maps,lightning fault replays,lightning hazard risk evaluations,and lightning simulated experiments,as well as novel lightning protection measures.The practical devices and systems corresponding to the technologies mentioned above are also introduced and discussed.Due to the progress of lightning protection technologies in recent years,despite the rapidly growing length of transmission lines in China,the lightning accident rate is controlled at a certain level.展开更多
The plasma characteristics of a lightning discharge channel are reviewed.The spectrum of the natural lightning is investigated by employing the slit-less spectrograph.It is found that the spectrum characteristics are ...The plasma characteristics of a lightning discharge channel are reviewed.The spectrum of the natural lightning is investigated by employing the slit-less spectrograph.It is found that the spectrum characteristics are closely related to the intensity of the lightning discharge.The lines in the lightning spectrum are classified into essential lines and characteristic lines,according to the characteristics of lightning spectra with different intensities.The characteristics of the lightning channel and the radiation of the lighting plasma are analyzed in the visible and infrared regions.It is shown that,the visible spectrum of lightning is determined by the radiation generated from the early stage to the development of lightning,while the near-infrared spectrum is determined by the radiation generated after current of lightning reaches the peak.The channel temperature and the electron density are calculated using the information obtained from the lightning spectrum.Both the temperature and the density decrease with the increasing length of lightning channel.Moreover,X-rays and neutrons are produced in the process of lighting mainly due to the pinch effects.展开更多
There are two major protective methods against lightning outages on overhead distribution lines.One is a surge arrester,and the other is an overhead ground wire.The surge arresters have rather constant effect regardle...There are two major protective methods against lightning outages on overhead distribution lines.One is a surge arrester,and the other is an overhead ground wire.The surge arresters have rather constant effect regardless of the cause of the lightning outage.On the other hand,the effect of an overhead ground wire is quite different in two major causes,the direct lightning hit and the induced overvoltage.It is sufficient to provide surge arresters with an interval of 300 m for protection against the induced overvoltage caused by the nearby lightning stroke.Use of an overhead ground wire together with surge arresters is effective for lightning protection against the direct lightning hit to a distribution line.Puncture of surge arresters is the popular outage when the outage caused by the insulation break decreases sufficiently.Also,the existence of nearby trees leads to the line break due to the side flash from a tree.Advanced lightning protection equipment with ZnO arrester components is popular in Japan.Modeling of a pole transformer and application of an electromagnetic analysis method,such as FDTD method,to surge phenomena is considerably advanced.展开更多
In addition to the conventional Franklin Rod,many non-conventional air terminals are being used as lightning protection devices.As cited in previous works,these non-conventional devices emit space charge in the vicini...In addition to the conventional Franklin Rod,many non-conventional air terminals are being used as lightning protection devices.As cited in previous works,these non-conventional devices emit space charge in the vicinity of the terminals during the process of lightning stroke.A number of factors affect the performance of these lightning protection devices,among them are geometry and dimension of the devices,location of the device above the ground,height of the cloud above the ground,and polarity of the lightning stroke.The performance of these lightning protection devices has been a topic of discussion by researchers for many years.Some studies focused on the magnitude of emission current from these devices as a criterion to evaluate their performances.The critical flashover voltage(CFO)between the devices and a metal screen simulating cloud can also be used as another criterion to evaluate the performance of the devices.Laboratory measurements were conducted in controlled conditions on different types of lightning protection devices to compare their performance.Four different types of devices were used in the present study:Franklin Rod,TerraStat models TS 100,TS 400,and Spline Ball Ionizer.The study focused on the CFO voltage of the air gap between devices and the metal screen.The CFO voltage was evaluated using standard switching and lightning impulses.The measurements were recorded for positive as well as negative polarity.The air gap between the devices and metal screen was selected at 2 m and 3 m.The results obtained provide a better understanding of the electrical performance of lightning protection devices.展开更多
This paper presents information concerning the characteristics of lightning overvoltages on overhead power distribution lines.Discussion on the protection measures against transients caused by both direct and indirect...This paper presents information concerning the characteristics of lightning overvoltages on overhead power distribution lines.Discussion on the protection measures against transients caused by both direct and indirect strokes is also presented.展开更多
In recent years,several failures of double circuit transmission line on the same tower due to lightning were happened in Beijing power grid.Although it can be reclosed successful,the lightning strike caused a grave th...In recent years,several failures of double circuit transmission line on the same tower due to lightning were happened in Beijing power grid.Although it can be reclosed successful,the lightning strike caused a grave threat to the power grid security.The cause of the accident and the accident process were studied for the sake of further understanding of the impact of lightning on power grid.As an example,110 kV double circuit transmission line(Xilong-line) was analyzed.At first,the system topology was given.Through the analysis on relay protection actions and the fault recorder data,over voltage on the insulator strings was calculated.Based on the analysis and the calculation,accident cause and the process were presented respectively.Secondly,it comes to the conclusion that the lightning failure was caused by counterattack.The wave of the lightning over voltage would spread to the not grounded neutral point of the transformers,and make the neutral protective gap breakdown,then cause freewheeling with the frequency of 50 Hz.As results of the relay protection,the double circuit transmission line all tripped out.Finally,the causes of the accident were proposed that included terrain features,large corner towers,strong thunderstorm weather and poor grounded contact of the tower.展开更多
Electric and magnetic fields generated by lightning cause a serious hazard to various systems.Now wind turbine installations with higher power capacity are increasing.Higher power capacity requires higher height and s...Electric and magnetic fields generated by lightning cause a serious hazard to various systems.Now wind turbine installations with higher power capacity are increasing.Higher power capacity requires higher height and so there is more probability of lightning strike.Blades are the most probable components to be struck by lightning.The most common lightning protection system for the blades consists of several metallic receptors on the blade surface.Those are connected to the ground by metallic down-conductors placed inside the blade shell.This paper studies effects of the receptor configurations on protecting the blade against lightning strike.For this purpose,an analysis procedure based on finite element method(FEM)in COMSOL Multiphysics software environment is used.The voltage distribution around the blade is simulated for various configurations of receptors.The best configuration is presented.Simulations are performed on the blade model of a special wind turbine,which isVESTAS V47".展开更多
The paper presents some problems of lightning overvoltage modeling in transmission lines with nonlinear elements.The presented results were obtained mostly for fast front transients of subsequent lightning return stro...The paper presents some problems of lightning overvoltage modeling in transmission lines with nonlinear elements.The presented results were obtained mostly for fast front transients of subsequent lightning return stroke currents.The effectiveness of numerical algorithms of nonlinear models and possibilities of their development for such transients are analyzed.Computer simulations carried out by application of EMTP show that nonlinear models of back-flashover and ZnO arresters work properly,while the implemented corona model can not be used for relatively large peak values of subsequent lightning return-stroke currents.展开更多
Transient over voltages due to lightning and switching surges cause steep build-up of voltage on transmission lines and other electrical apparatus,like circuit breakers,transformers,insulators etc.Therefore it is nece...Transient over voltages due to lightning and switching surges cause steep build-up of voltage on transmission lines and other electrical apparatus,like circuit breakers,transformers,insulators etc.Therefore it is necessary for the GIS also to withstand such voltages without breakdown of Insulation.The system has to be tested under these conditions.Usually the GIS system operates on power frequency.Lightning Impulse Voltage of 1050 kV and Switching Impulse Voltage of 750 kV superimposed on Power frequency voltages of 75 kV,100 kV and 132 kV are applied to Single Phase Gas Insulated Busduct and the maximum movement of Aluminum,Copper and Silver particles is determined.The movement patterns are also determined with and without Monte Carlo Simulation for movement of particle in axial and radial directions.The results show that there is a sudden jump in the movement at the application of impulse on sine wave.This is because of high magnitude voltage of 1050 kV during 1.2/50 μs.Similar movement patterns of reduced maximum movement is observed for Switching Impulse superimposed on sine wave.The results are presented and analyzed.展开更多
In order to obtain reasonable schemes of arrester in converter stations, the arrester scheme of "Xiluodu-Guangdong HVDC ± 500 kV double circuit transmission" project against lighting induced overvoltage...In order to obtain reasonable schemes of arrester in converter stations, the arrester scheme of "Xiluodu-Guangdong HVDC ± 500 kV double circuit transmission" project against lighting induced overvoltage, which was designed according to the main principle of lightning protection in converter station, is discussed. A calculation of the lighting induced overvoltage in Zhaotong converter station un- der various operation modes is performed with ATP-EMTP software, then the surge arrester configuration of the converter station is decided, and the arrester protection schemes of smoothing reactor and neutral line are studied. It is concluded that additional protection is necessary because of the relatively large gap between protected disconnecting switch and arrester of metallic return transfer bus. Plus, the smoothing reactor (SR) arrester near the valve hall could be removed to improve the scheme’s economic performance.展开更多
The operation data obtained abroad indicates that shielding failure in UHV transmission lines mostly accounts for the tripping-out accidents introduced by lightning striking the transmission line.Based on the discharg...The operation data obtained abroad indicates that shielding failure in UHV transmission lines mostly accounts for the tripping-out accidents introduced by lightning striking the transmission line.Based on the discharge theories of long air gap and randomness theory,a leader progression model of lightning shielding failure is presented in this paper.The random characteristics of the downward and upward leader are simulated in this model.The ground slope angel is also considered in this model by using coordinate transformation.Moreover,the system voltage is also taken into consideration in this model.The simulation results show that the good agreement between this model and the field data.And the results suggest that return striking exist obviously in UHV transmission line.展开更多
This paper presents a method for determining specific models of overhead power lines with presence of corona phenomenon. The obtained models provide stable numerical solutions for computer simulation of transients cau...This paper presents a method for determining specific models of overhead power lines with presence of corona phenomenon. The obtained models provide stable numerical solutions for computer simulation of transients caused by direct lightning strikes. The corona non- linear charge-voltage characteristics obtained from experimental tests are used for identification of the corona parameters based on System Identification Toolbox implemented in Matlab package. Different transfer functions, which give the same waveshapes of overvoltages are de- termined using two parametric models. A circuit representation of the obtained transfer functions is proposed and the corona model is implemented in the EMTP-RV as a hierarchical structure composed of a overhead power line divided into sections with corona branches. Some computer simulations of lightning overvoltages propagated in a typical 220 kV power line due to direct lightning strikes to a line tower are presented. The proposed method and the model implemented in EMTP-RV are still valid for multi-conductor lines and for higher voltages of power lines but new corona nonlinear charge-voltage characteristics are required as an input parameter for the identification procedure.展开更多
Looking at the problem of electrical discharge development in mineral oil, it is easy to see that most studies in this area focused on the setups of bare high voltage electrodes having a point-plane electrode arrangem...Looking at the problem of electrical discharge development in mineral oil, it is easy to see that most studies in this area focused on the setups of bare high voltage electrodes having a point-plane electrode arrangement. The setups with insulated electrodes are the mar- gin of these studies but it seems to be important to find the dependences between the paper insulation on high voltage electrode and parameters of the discharges initiated in the vicinity of this electrode. Hence, in this paper the results of researches intended to reveal the role of insulation wrapping on a HV electrode in the mechanism of electrical discharges in transformer oil under lightning impulse of both polar- ities are presented. This role is determined by analysis of the parameters characterizing the discharges (onset voltage, propagation velocity, time to initiation, rise-time of light impulses) and also by observation of their spatio-temporal development and oscillograms of the light emitted by their channels. The research was performed for two model electrode configurations: an electrode with paper insulation and a bare electrode which had the same outer dimensions as the insulated one. The most essential conclusion from performed experiment is related to times to initiation. These times, equal in the case of insulated electrodes and model bare electrode, indicate that the source of "weak points" of the paper-oil insulation system is the oil, not the surface of insulation wrapping or the metal.展开更多
文摘We present a comparison of data obtained during testing of lightning protective system of a residential structure in rocket-triggered lightning experiment at the International Center for Lightning Research and Testing(ICLRT)at Camp Blanding,Florida,and current surge generator experiment at Rzeszow University of Technology in Poland.Three different configurations of LPS were tested in Poland with the dc grounding resistances of the entire system 4.09 Ω(LPS 1a),1.65 Ω(LPS 1b),and 2.88 Ω(LPS 2).For LPS 1a with three ground rods the value of the peak current entering the electrical circuit neutral was about 56% of the injected current peak,and for LPS 1b with two additional ground rods and two 5 m long buried horizontal conductors it was about 16%.For LPS 2 with five ground rods interconnected by a buried loop conductor this ratio was 21%.The current waveshapes in the ground rods differed from the injected current waveshapes and the current waveshapes in other parts of the test system,especially,for poorer-grounding LPS 1a.The surge-generator results are consistent with those of triggered-lightning experiments at Camp Blanding,Florida(DeCarlo et al.,2008 [2]).
文摘It is one of the most effective ways to use laboratory long air gap discharges for investigating the fundamental process involved in the lightning strike.During the 1960s and the 1970s,the electro-geometrical method(EGM)and the rolling sphere method were developed base on the breakdowncharacteristics of negative long spark discharges,which have been widely used to design the lightning shielding system of transmission lines and structures.In recent years,the scale of the power facilities is increased dramatically with the rising of power grid's voltage level.The impact of upward connecting leader launched from those large-scale facilities on the lightning shielding performance cannot be neglected;otherwise,the validity of the EGM in the lightning shielding design of EHV and UHV transmission lines will be challenged.The research evolutions on the lightning striking distance,the lightning simulation experiments and the positive upward connecting leader process by using laboratory long sparks are reviewed and discussed in this paper.
基金Project supported by National Basic Research Program of China （973 Program） （2011CB209400）, National Fligh-tech Research and Developmerit Program of China （863 Program （2011AA040405）, National Natural Science Foundation of China （Ul134106）, 3551 Optics Valley Personal Plan of Wuhan East Lake High-tech Development Zone, Science and Technology Program of SGCC（SG[2009], SG[2013]）.
文摘In recent years,along with the rapid expansion of power grids,the increasing complication of grid structures,and the development of smart grids and energy technologies,the lightning protection of power grids becomes increasingly prominent.Power grids of China have acquired significant achievements on lightning protection technologies,which are reviewed in this paper.A technical route of lightning protection is introduced in detail; it allows us to find problems through detection and measurement of lightning,to analyze problems through evaluation and simulation of lightning,to solve problems through lightning protection measures,and to prevent problems through hazard risk warning of lightning.Following the route,the technical breakthroughs of these four aspects in China are presented,including the chinese lightning detection network(CLDN),natural lightning observations,lightning faults detection at transmission lines,lightning current measurements,progresses in lightning distribution maps,lightning fault replays,lightning hazard risk evaluations,and lightning simulated experiments,as well as novel lightning protection measures.The practical devices and systems corresponding to the technologies mentioned above are also introduced and discussed.Due to the progress of lightning protection technologies in recent years,despite the rapidly growing length of transmission lines in China,the lightning accident rate is controlled at a certain level.
基金Project supported by China Postdoctoral Science Foundation （ 10000072311030 ）, Scienee technology Research Foundation of Shandong University of China {10000080398125）.
基金Project supported by National Natural Science Foundation of China （11365019 41005004）.
文摘The plasma characteristics of a lightning discharge channel are reviewed.The spectrum of the natural lightning is investigated by employing the slit-less spectrograph.It is found that the spectrum characteristics are closely related to the intensity of the lightning discharge.The lines in the lightning spectrum are classified into essential lines and characteristic lines,according to the characteristics of lightning spectra with different intensities.The characteristics of the lightning channel and the radiation of the lighting plasma are analyzed in the visible and infrared regions.It is shown that,the visible spectrum of lightning is determined by the radiation generated from the early stage to the development of lightning,while the near-infrared spectrum is determined by the radiation generated after current of lightning reaches the peak.The channel temperature and the electron density are calculated using the information obtained from the lightning spectrum.Both the temperature and the density decrease with the increasing length of lightning channel.Moreover,X-rays and neutrons are produced in the process of lighting mainly due to the pinch effects.
文摘There are two major protective methods against lightning outages on overhead distribution lines.One is a surge arrester,and the other is an overhead ground wire.The surge arresters have rather constant effect regardless of the cause of the lightning outage.On the other hand,the effect of an overhead ground wire is quite different in two major causes,the direct lightning hit and the induced overvoltage.It is sufficient to provide surge arresters with an interval of 300 m for protection against the induced overvoltage caused by the nearby lightning stroke.Use of an overhead ground wire together with surge arresters is effective for lightning protection against the direct lightning hit to a distribution line.Puncture of surge arresters is the popular outage when the outage caused by the insulation break decreases sufficiently.Also,the existence of nearby trees leads to the line break due to the side flash from a tree.Advanced lightning protection equipment with ZnO arrester components is popular in Japan.Modeling of a pole transformer and application of an electromagnetic analysis method,such as FDTD method,to surge phenomena is considerably advanced.
文摘In addition to the conventional Franklin Rod,many non-conventional air terminals are being used as lightning protection devices.As cited in previous works,these non-conventional devices emit space charge in the vicinity of the terminals during the process of lightning stroke.A number of factors affect the performance of these lightning protection devices,among them are geometry and dimension of the devices,location of the device above the ground,height of the cloud above the ground,and polarity of the lightning stroke.The performance of these lightning protection devices has been a topic of discussion by researchers for many years.Some studies focused on the magnitude of emission current from these devices as a criterion to evaluate their performances.The critical flashover voltage(CFO)between the devices and a metal screen simulating cloud can also be used as another criterion to evaluate the performance of the devices.Laboratory measurements were conducted in controlled conditions on different types of lightning protection devices to compare their performance.Four different types of devices were used in the present study:Franklin Rod,TerraStat models TS 100,TS 400,and Spline Ball Ionizer.The study focused on the CFO voltage of the air gap between devices and the metal screen.The CFO voltage was evaluated using standard switching and lightning impulses.The measurements were recorded for positive as well as negative polarity.The air gap between the devices and metal screen was selected at 2 m and 3 m.The results obtained provide a better understanding of the electrical performance of lightning protection devices.
文摘This paper presents information concerning the characteristics of lightning overvoltages on overhead power distribution lines.Discussion on the protection measures against transients caused by both direct and indirect strokes is also presented.
文摘In recent years,several failures of double circuit transmission line on the same tower due to lightning were happened in Beijing power grid.Although it can be reclosed successful,the lightning strike caused a grave threat to the power grid security.The cause of the accident and the accident process were studied for the sake of further understanding of the impact of lightning on power grid.As an example,110 kV double circuit transmission line(Xilong-line) was analyzed.At first,the system topology was given.Through the analysis on relay protection actions and the fault recorder data,over voltage on the insulator strings was calculated.Based on the analysis and the calculation,accident cause and the process were presented respectively.Secondly,it comes to the conclusion that the lightning failure was caused by counterattack.The wave of the lightning over voltage would spread to the not grounded neutral point of the transformers,and make the neutral protective gap breakdown,then cause freewheeling with the frequency of 50 Hz.As results of the relay protection,the double circuit transmission line all tripped out.Finally,the causes of the accident were proposed that included terrain features,large corner towers,strong thunderstorm weather and poor grounded contact of the tower.
文摘Electric and magnetic fields generated by lightning cause a serious hazard to various systems.Now wind turbine installations with higher power capacity are increasing.Higher power capacity requires higher height and so there is more probability of lightning strike.Blades are the most probable components to be struck by lightning.The most common lightning protection system for the blades consists of several metallic receptors on the blade surface.Those are connected to the ground by metallic down-conductors placed inside the blade shell.This paper studies effects of the receptor configurations on protecting the blade against lightning strike.For this purpose,an analysis procedure based on finite element method(FEM)in COMSOL Multiphysics software environment is used.The voltage distribution around the blade is simulated for various configurations of receptors.The best configuration is presented.Simulations are performed on the blade model of a special wind turbine,which isVESTAS V47".
文摘The paper presents some problems of lightning overvoltage modeling in transmission lines with nonlinear elements.The presented results were obtained mostly for fast front transients of subsequent lightning return stroke currents.The effectiveness of numerical algorithms of nonlinear models and possibilities of their development for such transients are analyzed.Computer simulations carried out by application of EMTP show that nonlinear models of back-flashover and ZnO arresters work properly,while the implemented corona model can not be used for relatively large peak values of subsequent lightning return-stroke currents.
文摘Transient over voltages due to lightning and switching surges cause steep build-up of voltage on transmission lines and other electrical apparatus,like circuit breakers,transformers,insulators etc.Therefore it is necessary for the GIS also to withstand such voltages without breakdown of Insulation.The system has to be tested under these conditions.Usually the GIS system operates on power frequency.Lightning Impulse Voltage of 1050 kV and Switching Impulse Voltage of 750 kV superimposed on Power frequency voltages of 75 kV,100 kV and 132 kV are applied to Single Phase Gas Insulated Busduct and the maximum movement of Aluminum,Copper and Silver particles is determined.The movement patterns are also determined with and without Monte Carlo Simulation for movement of particle in axial and radial directions.The results show that there is a sudden jump in the movement at the application of impulse on sine wave.This is because of high magnitude voltage of 1050 kV during 1.2/50 μs.Similar movement patterns of reduced maximum movement is observed for Switching Impulse superimposed on sine wave.The results are presented and analyzed.
基金Project supported by Key Project of National Natural Science Foundation of China （50737003）.
文摘In order to obtain reasonable schemes of arrester in converter stations, the arrester scheme of "Xiluodu-Guangdong HVDC ± 500 kV double circuit transmission" project against lighting induced overvoltage, which was designed according to the main principle of lightning protection in converter station, is discussed. A calculation of the lighting induced overvoltage in Zhaotong converter station un- der various operation modes is performed with ATP-EMTP software, then the surge arrester configuration of the converter station is decided, and the arrester protection schemes of smoothing reactor and neutral line are studied. It is concluded that additional protection is necessary because of the relatively large gap between protected disconnecting switch and arrester of metallic return transfer bus. Plus, the smoothing reactor (SR) arrester near the valve hall could be removed to improve the scheme’s economic performance.
基金Project Supported by National Natural Science Foundation of China （50707036）, Key Project of the National Eleventh-five Year Research Program of China （2006BAA02A18）.
文摘The operation data obtained abroad indicates that shielding failure in UHV transmission lines mostly accounts for the tripping-out accidents introduced by lightning striking the transmission line.Based on the discharge theories of long air gap and randomness theory,a leader progression model of lightning shielding failure is presented in this paper.The random characteristics of the downward and upward leader are simulated in this model.The ground slope angel is also considered in this model by using coordinate transformation.Moreover,the system voltage is also taken into consideration in this model.The simulation results show that the good agreement between this model and the field data.And the results suggest that return striking exist obviously in UHV transmission line.
基金Project supported by the National Science Center, Poland
文摘This paper presents a method for determining specific models of overhead power lines with presence of corona phenomenon. The obtained models provide stable numerical solutions for computer simulation of transients caused by direct lightning strikes. The corona non- linear charge-voltage characteristics obtained from experimental tests are used for identification of the corona parameters based on System Identification Toolbox implemented in Matlab package. Different transfer functions, which give the same waveshapes of overvoltages are de- termined using two parametric models. A circuit representation of the obtained transfer functions is proposed and the corona model is implemented in the EMTP-RV as a hierarchical structure composed of a overhead power line divided into sections with corona branches. Some computer simulations of lightning overvoltages propagated in a typical 220 kV power line due to direct lightning strikes to a line tower are presented. The proposed method and the model implemented in EMTP-RV are still valid for multi-conductor lines and for higher voltages of power lines but new corona nonlinear charge-voltage characteristics are required as an input parameter for the identification procedure.
文摘Looking at the problem of electrical discharge development in mineral oil, it is easy to see that most studies in this area focused on the setups of bare high voltage electrodes having a point-plane electrode arrangement. The setups with insulated electrodes are the mar- gin of these studies but it seems to be important to find the dependences between the paper insulation on high voltage electrode and parameters of the discharges initiated in the vicinity of this electrode. Hence, in this paper the results of researches intended to reveal the role of insulation wrapping on a HV electrode in the mechanism of electrical discharges in transformer oil under lightning impulse of both polar- ities are presented. This role is determined by analysis of the parameters characterizing the discharges (onset voltage, propagation velocity, time to initiation, rise-time of light impulses) and also by observation of their spatio-temporal development and oscillograms of the light emitted by their channels. The research was performed for two model electrode configurations: an electrode with paper insulation and a bare electrode which had the same outer dimensions as the insulated one. The most essential conclusion from performed experiment is related to times to initiation. These times, equal in the case of insulated electrodes and model bare electrode, indicate that the source of "weak points" of the paper-oil insulation system is the oil, not the surface of insulation wrapping or the metal.
