A new dimensionless number is proposed for dynamic plastic deformation analysis of clamped circular plates under underwater explosion loads by introducing dimensional analysis method to the basic dynamical governing e...A new dimensionless number is proposed for dynamic plastic deformation analysis of clamped circular plates under underwater explosion loads by introducing dimensional analysis method to the basic dynamical governing equations of circular plates.The relation between dimensionless final plastic deformation of circular plates and the new dimensionless number is established based on massive underwater explosion test data.Meanwhile,comparative analysis was discussed with two other published dimensionless parameters which indicated the new dimensionless number proposed in this paper is more effective and extensive to predict the dynamic plastic response of circular plates under underwater explosion condition.展开更多
General situation of China plastics industry in 2009 was reviewed,including the output/sales and export/import of plastics products,synthetic resins,plastics processing machinery and additives.
Texture evolution and inhomogeneous deformation of polycrystalline Cu during uniaxial compression are investigated at the grain scale by combining crystal plasticity finite element method(CPFEM) with particle swarm op...Texture evolution and inhomogeneous deformation of polycrystalline Cu during uniaxial compression are investigated at the grain scale by combining crystal plasticity finite element method(CPFEM) with particle swarm optimization(PSO) algorithm. The texture-based representative volume element(TBRVE) is used in the crystal plasticity finite element model, where a given number of crystallographic orientations are obtained by means of discretizing the orientation distribution function(ODF) based on electron backscattered diffraction(EBSD) experiment data. Three-dimensional grains with different morphologies are generated on the basis of Voronoi tessellation. The PSO algorithm plays a significant role in identifying the material parameters and saving computational time. The macroscopic stress–strain curve is predicted based on CPFEM, where the simulation results are in good agreement with the experimental ones. Therefore, CPFEM is a powerful candidate for capturing the texture evolution and clarifying the inhomogeneous plastic deformation of polycrystalline Cu. The simulation results indicate that the <110> fiber texture is generated finally with the progression of plastic deformation. The inhomogeneous distribution of rotation angles lays the foundation for the inhomogeneous deformation of polycrystalline Cu in terms of grain scale.展开更多
Plastic variational principles are foundation to solve the boundary-value problems of plastic mechanics with the variational method(or energy method) and finite element method.The most convenient way of establishing d...Plastic variational principles are foundation to solve the boundary-value problems of plastic mechanics with the variational method(or energy method) and finite element method.The most convenient way of establishing different kinds of variational principles is to set up the extreme principle related to the studied problem.Based on a general new extreme principle-the Least work consumption principle,the variational principles of the rigid-plastic and rigid-viscoplastic material were derived.In comparison with existing methods,the method in this paper is more clear and direct,and the physical meaning is clear-cut.This method can offer a new way for establishing other kinds of variational principles.展开更多
The mechanical properties of composites prepared from wood flour and thermoplastic blends were investigated. Thermoplastic mixtures of polypropylene (PP) and high-density polyethylene (HDPE) and polystyrene (PS), virg...The mechanical properties of composites prepared from wood flour and thermoplastic blends were investigated. Thermoplastic mixtures of polypropylene (PP) and high-density polyethylene (HDPE) and polystyrene (PS), virgin or recycled, were mixed with wood flour in a high speed blender and then extruded by a specially designed twin/single screw extruder system to form wood-flour/thermoplastic-blends composites (WTBCs). Comparative studies were made to evaluate the effectiveness of the two modification methods of the thermoplastic blends, the one of the addition of maleic anhydride grafted styrene-ethylene-butylene-styrene block copolymer (SEBS-g-MAH) as compatibilizer and the other of blend grafting of maleic anhydride (MAH) using dicumyl peroxide (DCP) as initiator by reactive extrusion. The results showed that the impact properties of WTBCs using SEBS-g-MAH as compatilizer were better improved than that of the blend grafting. However, adverse results were observed on the tensile and flexural properties of the corresponding WTBCs. The mechanical properties of WTBCs prepared from recycled plastic blends were poorer to some extent than that from virgin plastic blends in general, especially in elongation break. The morphology of WTBCs breaking section was analyzed by scanning electron microscopy (SEM) and the results showed that a good interfacial adhesion between wood flour and polymer matrix was observed with both of the two modification methods. However, by blend grafting of adding DCP as initiator and MAH as monomer, a better interfacial bonding between wood and plastic matrix was obtained than that of the addition of SEBS-g-MAH. Blend grafting can be considered as a potential way of increasing the interfacial compatibility of different plastics and between plastic blends and wood.展开更多
This work describes thermal decomposition behaviour of plastic bonded explosives(PBXs) based on mixture of 1,3,5,7-tetranitro-1,3,5,7-tetrazocane(HMX) and 2,4,6-triamino-1,3,5-trinitrobenzene(TATB)with Viton A as poly...This work describes thermal decomposition behaviour of plastic bonded explosives(PBXs) based on mixture of 1,3,5,7-tetranitro-1,3,5,7-tetrazocane(HMX) and 2,4,6-triamino-1,3,5-trinitrobenzene(TATB)with Viton A as polymer binder. Thermal decomposition of PBXs was undertaken by applying simultaneous thermal analysis(STA) and differential scanning calorimetry(DSC) to investigate influence of the HMX amount on thermal behavior and its kinetics. Thermogravimetric analysis(TGA) indicated that the thermal decomposition of PBXs based on mixture of HMX and TATB was occurred in a three-steps. The first step was mainly due to decomposition of HMX. The second step was ascribed due to decomposition of TATB, while the third step was occurred due to decomposition of the polymer matrices. The thermal decomposition % was increased with increasing HMX amount. The kinetics related to thermal decomposition were investigated under non-isothermal for a single heating rate measurement. The variation in the activation energy of PBXs based on mixture of HMX and TATB was observed with varying the HMX amount. The kinetics from the results of TGA data at various heating rates under non-isothermal conditions were also calculated by Flynn—Wall—Ozawa(FWO) and Kissinger-Akahira-Sunose(KAS)methods. The activation energies calculated by employing FWO method were very close to those obtained by KAS method. The mean activation energy calculated by FWO and KAS methods was also a good agreement with the activation energy obtained from single heating rate measurement in the first step decomposition.展开更多
The mechanical behavior of plastic concrete used in the cut-off walls of earth dams has been studied. Triaxial compression tests on the specimens in various ages and mix designs under different confining pressures hav...The mechanical behavior of plastic concrete used in the cut-off walls of earth dams has been studied. Triaxial compression tests on the specimens in various ages and mix designs under different confining pressures have been done and the stress-strain behavior of such materials and their strength parameter changes have been experimentally investigated. It has been observed that increasing the confining pressures applied on the specimens causes the material behavior to be alike the more ductile materials and the compressive strength increases considerably as well. Moreover, a parametric study has been carded out to investigate the influence of essential parameters on the shear strength parameters of these materials. According to the research, increasing the coarse to fine aggregates ratio leads to the increase of compressive strength of the specimens as well as the increase of the cohesion and internal friction angle of the materials. Furthermore, the bentonite content decrease and the cement factor increase result in an increase of the cohesion parameter of plastic concretes and decrease of the internal friction angle of such materials.展开更多
Cross-wedge rolling (CWR) is a metal process of ro ta ry forming. To produce a part, one cylindrical billet should be placed between t wo counterrotating and wedge-shape dies, which move tangentially relative each oth...Cross-wedge rolling (CWR) is a metal process of ro ta ry forming. To produce a part, one cylindrical billet should be placed between t wo counterrotating and wedge-shape dies, which move tangentially relative each other. The billet suffers plastic deformation (essentially, localized compressio n) during its rotation between the rotating dies. Compared to other numerical si mulation methods, the finite element method (FEM) has advantages in solving gene ral problems with complex shapes of the formed parts. In cross-wedge rolling, t here are four stages in the workpiece deformation process, namely knifing, guidi ng, stretching and sizing stage. It is time-consuming and expensive to design t he CWR process by trial and error method. The application of numerical simul ation for the CWR process will help engineers to efficiently improve the process development. Tselikov, Hayama, Jain and Kobayashi, and Higashimo applied the sl ip-line theory in study of CWR process analysis. Zb.pater studied CWR process i ncluding upsetting by upper-bound method. The above numerical simulation were b ased on the two-dimensional plain-strain assumption ignored the metal flow in workpiece axial direction. Therefore, the complex three-dimensional stress and deformation involved in CWR processes were not presented. Compared to other nume rical simulation methods, the finite element method (FEM) has advantages in solv ing general problems with complex shapes of the formed parts. As yet, a few 3-D finite element simulation studies on CWR process have been reported in literatu res. In this paper, the process of cross wedge rolling (CWR) has been simulated and analyzed by 3D rigid-plastic finite element method. Considering the charact eristic of CWR, the static implicit FEM program is selected. The models proposed in this study uses the commercial code DEFORM 3D to simulate the CWR process. T his is an implicit Lagrangian finite element code, which includes many new enhan cements functions. A new method of utilizing multiple processors using the MPI s tandard has been implemented. Automatic switching between the two different defo rmation solvers (Sparse Solver and Conjugate Gradient Solver) has also been impl emented in order to increase the speed of simulations. In this paper, all stages in CWR process are simulated to be able to closely understand and analyze the a ctual CWR process. For simulating all forming stages in CWR process, the dynam ic adaptive remeshing technology for tetrahedral solid elements was applied. T he stress distributions in cross section of forming workpiece are analyzed to in terpret fracture or rarefaction in the center of workpiece. Authors also analyze d the time-torque curve and the laws of load changing.展开更多
The need to develop armour systems to protect against attacks from various sources is increasingly a matter of personal,social and national security.To develop innovative armour systems it is necessary to monitor deve...The need to develop armour systems to protect against attacks from various sources is increasingly a matter of personal,social and national security.To develop innovative armour systems it is necessary to monitor developments being made on the type,technology and performance of the threats(weapons,projectiles,explosives,etc.) Specifically,the use of high protection level helmets on the battlefield is essential.The development of evaluation methods that can predict injuries and trauma is therefore of major importance.However,the risk of injuries or trauma that can arise from induced accelerations is an additional consideration.To develop new materials and layouts for helmets it is necessary to study the effects caused by ballistic impacts in the human head on various scenarios.The use of numerical simulation is a fundamental tool in this process.The work here presented focuses on the use of numerical simulation(finite elements analysis) to predict the consequences of bullet impacts on military helmets on human injuries.The main objectives are to assess the level and probability of head trauma using the Head Injury Criterion,caused by the impact of a 9 mm NATO projectile on a PASGT helmet and to quantify the relevance of projectile plasticity on the whole modelling process.The accelerations derived from the impact phenomenon and the deformations caused on the helmet are evaluated using fully three-dimensional models of the helmet,head,neck and projectile.Impact studies are done at impact angles ranging from 0 to 75°.Results are presented and discussed in terms of HIC and probability of acceleration induced trauma levels.Thorough comparison analyses are done using a rigid and a deformable projectile and it is observed that plastic deformation of the projectile is a significant energy dissipation mechanism in the whole impact process.展开更多
The predictive capacity of numerical analyses in geotechnical engineering depends strongly on the efficiency of constitutive models used for modeling of interfaces behavior.Interfaces are considered as thin layers of ...The predictive capacity of numerical analyses in geotechnical engineering depends strongly on the efficiency of constitutive models used for modeling of interfaces behavior.Interfaces are considered as thin layers of the soil adjacent to structures boundary whose major role is transferring loads from structures to soil masses.An interface model within the bounding surface plasticity framework and the critical state soil mechanics is presented.To this aim,general formulation of the interface model according to the bounding surface plasticity theory is described first.Similar to granular soils,it has been shown that the mechanical behavior of sand-structure interfaces is highly affected by the interface state that is the combined influences of density and applied normal stress.Therefore,several ingredients of the model are directly related to the interface state.As a result of this feature,the model is enabled to distinguish interfaces in dense state from those in loose state and to provide realistic predictions over wide ranges of density and normal stress values.In evaluation of the model,a reasonable correspondence between the model predictions and the experimental data of various research teams is found.展开更多
Dilation angle is a significant parameter needed for numerical simulation of tunnels.Even though dilation parameter is physically variable and dependent on confinement and experienced shear plastic strain based on the...Dilation angle is a significant parameter needed for numerical simulation of tunnels.Even though dilation parameter is physically variable and dependent on confinement and experienced shear plastic strain based on the existing dilation models,numerical simulations of tunnels and underground openings with constant dilation parameter usually lead to satisfactory results in practical use.This study aims to find out why constant dilation angle is enough under practical conditions to simulate numerically tunnels and underground excavations in spite of the fact that dilation angle is variable in laboratory and experimental scale.With this aim,this work studies how mobilized dilation angle varies in a plastic zone surrounding a tunnel.For the circular tunnel under uniform in situ stress field,the stepwise finite difference approximation analytical solution considering strain softening rock mass behavior with mobilized dilation angle was used to study how mobilized dilation angle varies in plastic zone around tunnel under very different conditions.In practical conditions determined in this study,dilative behavior of all over the plastic zone around the tunnel can be approximated to constant dilation angle in the middle region of the plastic zone.Moreover,the plastic zone displacements for mobilized and constant dilation angle models are compared with each other.Further investigation under more general non-uniform in situ stress conditions and non-circular tunnels is performed by using the commercial finite difference software to numerically simulate the Mine-by experimental tunnel of AECL(Atomic Energy of Canada Limited)and the arched tunnel.Although the Mine-by and arched tunnels were numerically simulated based on the mobilized dilation angle model,the variability associated with dilation angle around the simulated Mine-by and arched tunnels is insignificant,and dilation angle is approximately constant in the plastic zone.展开更多
In this study,we present the characterization of the carbon fibers recovered from the mechanochemical-enhanced recycling of carbon fiber reinforced fibers.The objectives of the study were to investigate the effect of ...In this study,we present the characterization of the carbon fibers recovered from the mechanochemical-enhanced recycling of carbon fiber reinforced fibers.The objectives of the study were to investigate the effect of our modified recycling method on the interfacial properties of recovered fibers.The reinforced plastics were recycled;the recycling efficiency was determined and the recovered fibers were sized using 1 wt%and 3 wt%concentration of(3-aminopropyl)triethoxysilane.We characterized the morphologies utilizing the electron spectroscopy for chemical analysis(ESCA),atomic force microscopy(AFM),FTIR-attenuated total reflection(ATR)spectroscopy and scanning electron microscopy(SEM).Although the surface of the fibers had no cracks,there was evidence of contaminations which affected the interfacial properties and the quality of the fibers.Results showed that the trends in the recovered and virgin fibers were similar with an increase in sizing concentration.The results highlighted the perspectives of increasing the quality of recovered fibers after the recycling process.展开更多
Based on the pseudo potential plane-wave method of density functional theory （DFT）, Ti1-xNbxAk （x=0, 0.062 5, 0.083 3, 0.125, 0.250） crystals＇ geometry structure, elastic constants, electronic structure and Mulli...Based on the pseudo potential plane-wave method of density functional theory （DFT）, Ti1-xNbxAk （x=0, 0.062 5, 0.083 3, 0.125, 0.250） crystals＇ geometry structure, elastic constants, electronic structure and Mulliken populations were calculated, and the effects of doping on the geometric structure, electronic structure and bond strength were systematically analyzed. The results show that the influence of Nb on the geometric structure is little in terms of the plasticity, and with the increase of Nb content, the covalent bond strength remarkably reduces, and Ti-Al, Nb-M （M=Ti, Al） and other hybrid bonds enhance; meanwhile, the peak district increases and the pseudo-energy gap first decreases and then increases, the overall band structure narrows, the covalent bond and direction of bonds reduce. The population analysis also shows that the results are consistent with the electronic structure analysis. The density of states of TiAINb shows that Nb doping can enhance the activity of Al and benefit the form of Al2O3 film. All the calculations reveal that the room temperature plasticity and the antioxidation properties of the compounds can be improved with the Nb content of 8.33%-12.5% （mole fraction）.展开更多
The effects of process parameters in rapid heat cycle moulding （RHCM） on parts warpage were investigated. A vehicle-used blue-tooth front shell （consisting of ABS material） was considered as a part example manufac...The effects of process parameters in rapid heat cycle moulding （RHCM） on parts warpage were investigated. A vehicle-used blue-tooth front shell （consisting of ABS material） was considered as a part example manufactured by RHCM method. The corresponding rapid heat response mould with an innovational conformal heating/cooling channel system and a dynamic mould temperature control system based on the Jll-W-160 type precise temperature controller was proposed. During heating/cooling process, the mould was able to be heated from room temperature to 160 ~C in 6 s and then cooled to 80 ~C in 22 s. The effects of processing conditions in RHCM on part warpage were investigated based on the single factor experimental method and Taguchi theory. Results reveal that the elevated mould temperature reduces unwanted freezing during the injection stage, thus improving mouldability and enhancing part quality, whereas the overheated of mould temperature will lead to defective product. The feasible mould temperature scope in RHCM should be no higher than 140 ~C, and the efficient mould temperature scope should be around the polymer heat distortion temperature. Melt temperature as well as injection pressure effects on warpage can be divided into two stages The lower stage gives a no explicit effect on warpage whereas the higher stage leads to a quasi-linear downtrend. But others affect the warpage as a V-type fluctuation, reaching to the minimum around the heat distortion temperature. Under the same mould temperature condition, the effects of process parameters on warpage decrease according to the following order, packing time, packing pressure, melt temperature, injection pressure and cooling time, respectively.展开更多
In order to improve the properties of rice straw fiber film, one factor contrast test method was employed. Plasticizer type was chosen as input variable, dry tension strength and elongation, wet tension strength and e...In order to improve the properties of rice straw fiber film, one factor contrast test method was employed. Plasticizer type was chosen as input variable, dry tension strength and elongation, wet tension strength and elongation, bursting strength and tearing strength were chosen as indexes. The results showed that there were significant differences among the means of dry tension strength, dry elongation and bursting strength of different plasticizers; there were not significant differences among the means of wet tension strength, wet elongation and tearing strength of different plasticizers; for dry tension strength and elongation, glycerol had a significant difference with sorbitol and PEG, no significant difference was observed between sorbitol and PEG, dry tension strength added glycerol had been reduced 6.8% compared with that added sorbitol, reduced 9.5% compared with that added PEG; elongation had been improved 6.1% and 9.4%, respectively; for bursting strength, sorbitol had a significant difference with glycerol and PEG, no significant difference was observed between glycerol and PEG; bursting strength added glycerol and added PEG had been improved 6.9% and 5.6%, respectively compared with that of the added sorbitol. The results provided a theoretical reference for further improving the straw fiber film manufacturing process.展开更多
Rehabilitation of existing structures with fiber reinforced plastic(FRP)has been growing in popularity because they offer superior performance in terms of resistance to corrosion and high specific stiffness.The strain...Rehabilitation of existing structures with fiber reinforced plastic(FRP)has been growing in popularity because they offer superior performance in terms of resistance to corrosion and high specific stiffness.The strain coordination results of 34 reinforced concrete beams(four groups)strengthened with different methods were presented including external-bonded or near-surface mounted glass or carbon FRP or helical rib bar in order to study the strain coordination of the strengthening materials and steel rebar of RC beam.Because there is relative slipping between concrete and strengthening materials(SM),the strain of SM and steel rebar of RC beam satisfies the double linear strain distribution assumption,that is,the strain of longitudinal fiber parallel to the neutral axis of plated beam within the scope of effective height(h0)of the cross section is in direct proportion to the distance from the fiber to the neutral axis.The strain of SM and steel rebar satisfies the equation εGCH=βεsteel,where the value of β is equal to 1.1-1.3 according to the test results.展开更多
In order to overcome the nonlinearity of Mises criterion, a new linear yield criterion with a dodecagon shape of the same perimeter as Mises criterion was derived by means of geometrical analysis. Its specific plastic...In order to overcome the nonlinearity of Mises criterion, a new linear yield criterion with a dodecagon shape of the same perimeter as Mises criterion was derived by means of geometrical analysis. Its specific plastic work rate expressed as a linear function of the yield stress, the maximum and minimum strains was also deduced and compared with that of Mises criterion. The physical meaning of the proposed yield criterion is that yielding of materials begins when the shear yield stress τs reaches the magnitude of 0.594σs. By introducing the Lode parameter, validation of evolution expressions of the proposed yield criterion with those based on Tresca, Mises and TSS criteria as well as available classical yield experimental results of various metals shows that the present results intersect with Mises results and coincide well with experimental data. Moreover, further application to the limit analysis of circle plate as an example is performed to demonstrate the effectiveness of the proposed yield criterion, and the subsequent comparison of limit loads with the Tresca analytical solutions and Mises numerical results shows that the present results are higher than the Tresca analytical results, and are in good agreement with the Mises numerical results.展开更多
基金supported by the National Natural Science Foundation of China(12402444)。
文摘A new dimensionless number is proposed for dynamic plastic deformation analysis of clamped circular plates under underwater explosion loads by introducing dimensional analysis method to the basic dynamical governing equations of circular plates.The relation between dimensionless final plastic deformation of circular plates and the new dimensionless number is established based on massive underwater explosion test data.Meanwhile,comparative analysis was discussed with two other published dimensionless parameters which indicated the new dimensionless number proposed in this paper is more effective and extensive to predict the dynamic plastic response of circular plates under underwater explosion condition.
文摘General situation of China plastics industry in 2009 was reviewed,including the output/sales and export/import of plastics products,synthetic resins,plastics processing machinery and additives.
基金Projects(51305091,51475101) supported by the National Natural Science Foundation of ChinaProject(20132304120025) supported by Specialized Research Fund for the Doctoral Program of Higher Education,China
文摘Texture evolution and inhomogeneous deformation of polycrystalline Cu during uniaxial compression are investigated at the grain scale by combining crystal plasticity finite element method(CPFEM) with particle swarm optimization(PSO) algorithm. The texture-based representative volume element(TBRVE) is used in the crystal plasticity finite element model, where a given number of crystallographic orientations are obtained by means of discretizing the orientation distribution function(ODF) based on electron backscattered diffraction(EBSD) experiment data. Three-dimensional grains with different morphologies are generated on the basis of Voronoi tessellation. The PSO algorithm plays a significant role in identifying the material parameters and saving computational time. The macroscopic stress–strain curve is predicted based on CPFEM, where the simulation results are in good agreement with the experimental ones. Therefore, CPFEM is a powerful candidate for capturing the texture evolution and clarifying the inhomogeneous plastic deformation of polycrystalline Cu. The simulation results indicate that the <110> fiber texture is generated finally with the progression of plastic deformation. The inhomogeneous distribution of rotation angles lays the foundation for the inhomogeneous deformation of polycrystalline Cu in terms of grain scale.
文摘Plastic variational principles are foundation to solve the boundary-value problems of plastic mechanics with the variational method(or energy method) and finite element method.The most convenient way of establishing different kinds of variational principles is to set up the extreme principle related to the studied problem.Based on a general new extreme principle-the Least work consumption principle,the variational principles of the rigid-plastic and rigid-viscoplastic material were derived.In comparison with existing methods,the method in this paper is more clear and direct,and the physical meaning is clear-cut.This method can offer a new way for establishing other kinds of variational principles.
文摘The mechanical properties of composites prepared from wood flour and thermoplastic blends were investigated. Thermoplastic mixtures of polypropylene (PP) and high-density polyethylene (HDPE) and polystyrene (PS), virgin or recycled, were mixed with wood flour in a high speed blender and then extruded by a specially designed twin/single screw extruder system to form wood-flour/thermoplastic-blends composites (WTBCs). Comparative studies were made to evaluate the effectiveness of the two modification methods of the thermoplastic blends, the one of the addition of maleic anhydride grafted styrene-ethylene-butylene-styrene block copolymer (SEBS-g-MAH) as compatibilizer and the other of blend grafting of maleic anhydride (MAH) using dicumyl peroxide (DCP) as initiator by reactive extrusion. The results showed that the impact properties of WTBCs using SEBS-g-MAH as compatilizer were better improved than that of the blend grafting. However, adverse results were observed on the tensile and flexural properties of the corresponding WTBCs. The mechanical properties of WTBCs prepared from recycled plastic blends were poorer to some extent than that from virgin plastic blends in general, especially in elongation break. The morphology of WTBCs breaking section was analyzed by scanning electron microscopy (SEM) and the results showed that a good interfacial adhesion between wood flour and polymer matrix was observed with both of the two modification methods. However, by blend grafting of adding DCP as initiator and MAH as monomer, a better interfacial bonding between wood and plastic matrix was obtained than that of the addition of SEBS-g-MAH. Blend grafting can be considered as a potential way of increasing the interfacial compatibility of different plastics and between plastic blends and wood.
基金DRDO(TBR-1251)for funding and awarding the Project
文摘This work describes thermal decomposition behaviour of plastic bonded explosives(PBXs) based on mixture of 1,3,5,7-tetranitro-1,3,5,7-tetrazocane(HMX) and 2,4,6-triamino-1,3,5-trinitrobenzene(TATB)with Viton A as polymer binder. Thermal decomposition of PBXs was undertaken by applying simultaneous thermal analysis(STA) and differential scanning calorimetry(DSC) to investigate influence of the HMX amount on thermal behavior and its kinetics. Thermogravimetric analysis(TGA) indicated that the thermal decomposition of PBXs based on mixture of HMX and TATB was occurred in a three-steps. The first step was mainly due to decomposition of HMX. The second step was ascribed due to decomposition of TATB, while the third step was occurred due to decomposition of the polymer matrices. The thermal decomposition % was increased with increasing HMX amount. The kinetics related to thermal decomposition were investigated under non-isothermal for a single heating rate measurement. The variation in the activation energy of PBXs based on mixture of HMX and TATB was observed with varying the HMX amount. The kinetics from the results of TGA data at various heating rates under non-isothermal conditions were also calculated by Flynn—Wall—Ozawa(FWO) and Kissinger-Akahira-Sunose(KAS)methods. The activation energies calculated by employing FWO method were very close to those obtained by KAS method. The mean activation energy calculated by FWO and KAS methods was also a good agreement with the activation energy obtained from single heating rate measurement in the first step decomposition.
文摘The mechanical behavior of plastic concrete used in the cut-off walls of earth dams has been studied. Triaxial compression tests on the specimens in various ages and mix designs under different confining pressures have been done and the stress-strain behavior of such materials and their strength parameter changes have been experimentally investigated. It has been observed that increasing the confining pressures applied on the specimens causes the material behavior to be alike the more ductile materials and the compressive strength increases considerably as well. Moreover, a parametric study has been carded out to investigate the influence of essential parameters on the shear strength parameters of these materials. According to the research, increasing the coarse to fine aggregates ratio leads to the increase of compressive strength of the specimens as well as the increase of the cohesion and internal friction angle of the materials. Furthermore, the bentonite content decrease and the cement factor increase result in an increase of the cohesion parameter of plastic concretes and decrease of the internal friction angle of such materials.
文摘Cross-wedge rolling (CWR) is a metal process of ro ta ry forming. To produce a part, one cylindrical billet should be placed between t wo counterrotating and wedge-shape dies, which move tangentially relative each other. The billet suffers plastic deformation (essentially, localized compressio n) during its rotation between the rotating dies. Compared to other numerical si mulation methods, the finite element method (FEM) has advantages in solving gene ral problems with complex shapes of the formed parts. In cross-wedge rolling, t here are four stages in the workpiece deformation process, namely knifing, guidi ng, stretching and sizing stage. It is time-consuming and expensive to design t he CWR process by trial and error method. The application of numerical simul ation for the CWR process will help engineers to efficiently improve the process development. Tselikov, Hayama, Jain and Kobayashi, and Higashimo applied the sl ip-line theory in study of CWR process analysis. Zb.pater studied CWR process i ncluding upsetting by upper-bound method. The above numerical simulation were b ased on the two-dimensional plain-strain assumption ignored the metal flow in workpiece axial direction. Therefore, the complex three-dimensional stress and deformation involved in CWR processes were not presented. Compared to other nume rical simulation methods, the finite element method (FEM) has advantages in solv ing general problems with complex shapes of the formed parts. As yet, a few 3-D finite element simulation studies on CWR process have been reported in literatu res. In this paper, the process of cross wedge rolling (CWR) has been simulated and analyzed by 3D rigid-plastic finite element method. Considering the charact eristic of CWR, the static implicit FEM program is selected. The models proposed in this study uses the commercial code DEFORM 3D to simulate the CWR process. T his is an implicit Lagrangian finite element code, which includes many new enhan cements functions. A new method of utilizing multiple processors using the MPI s tandard has been implemented. Automatic switching between the two different defo rmation solvers (Sparse Solver and Conjugate Gradient Solver) has also been impl emented in order to increase the speed of simulations. In this paper, all stages in CWR process are simulated to be able to closely understand and analyze the a ctual CWR process. For simulating all forming stages in CWR process, the dynam ic adaptive remeshing technology for tetrahedral solid elements was applied. T he stress distributions in cross section of forming workpiece are analyzed to in terpret fracture or rarefaction in the center of workpiece. Authors also analyze d the time-torque curve and the laws of load changing.
文摘The need to develop armour systems to protect against attacks from various sources is increasingly a matter of personal,social and national security.To develop innovative armour systems it is necessary to monitor developments being made on the type,technology and performance of the threats(weapons,projectiles,explosives,etc.) Specifically,the use of high protection level helmets on the battlefield is essential.The development of evaluation methods that can predict injuries and trauma is therefore of major importance.However,the risk of injuries or trauma that can arise from induced accelerations is an additional consideration.To develop new materials and layouts for helmets it is necessary to study the effects caused by ballistic impacts in the human head on various scenarios.The use of numerical simulation is a fundamental tool in this process.The work here presented focuses on the use of numerical simulation(finite elements analysis) to predict the consequences of bullet impacts on military helmets on human injuries.The main objectives are to assess the level and probability of head trauma using the Head Injury Criterion,caused by the impact of a 9 mm NATO projectile on a PASGT helmet and to quantify the relevance of projectile plasticity on the whole modelling process.The accelerations derived from the impact phenomenon and the deformations caused on the helmet are evaluated using fully three-dimensional models of the helmet,head,neck and projectile.Impact studies are done at impact angles ranging from 0 to 75°.Results are presented and discussed in terms of HIC and probability of acceleration induced trauma levels.Thorough comparison analyses are done using a rigid and a deformable projectile and it is observed that plastic deformation of the projectile is a significant energy dissipation mechanism in the whole impact process.
文摘The predictive capacity of numerical analyses in geotechnical engineering depends strongly on the efficiency of constitutive models used for modeling of interfaces behavior.Interfaces are considered as thin layers of the soil adjacent to structures boundary whose major role is transferring loads from structures to soil masses.An interface model within the bounding surface plasticity framework and the critical state soil mechanics is presented.To this aim,general formulation of the interface model according to the bounding surface plasticity theory is described first.Similar to granular soils,it has been shown that the mechanical behavior of sand-structure interfaces is highly affected by the interface state that is the combined influences of density and applied normal stress.Therefore,several ingredients of the model are directly related to the interface state.As a result of this feature,the model is enabled to distinguish interfaces in dense state from those in loose state and to provide realistic predictions over wide ranges of density and normal stress values.In evaluation of the model,a reasonable correspondence between the model predictions and the experimental data of various research teams is found.
文摘Dilation angle is a significant parameter needed for numerical simulation of tunnels.Even though dilation parameter is physically variable and dependent on confinement and experienced shear plastic strain based on the existing dilation models,numerical simulations of tunnels and underground openings with constant dilation parameter usually lead to satisfactory results in practical use.This study aims to find out why constant dilation angle is enough under practical conditions to simulate numerically tunnels and underground excavations in spite of the fact that dilation angle is variable in laboratory and experimental scale.With this aim,this work studies how mobilized dilation angle varies in a plastic zone surrounding a tunnel.For the circular tunnel under uniform in situ stress field,the stepwise finite difference approximation analytical solution considering strain softening rock mass behavior with mobilized dilation angle was used to study how mobilized dilation angle varies in plastic zone around tunnel under very different conditions.In practical conditions determined in this study,dilative behavior of all over the plastic zone around the tunnel can be approximated to constant dilation angle in the middle region of the plastic zone.Moreover,the plastic zone displacements for mobilized and constant dilation angle models are compared with each other.Further investigation under more general non-uniform in situ stress conditions and non-circular tunnels is performed by using the commercial finite difference software to numerically simulate the Mine-by experimental tunnel of AECL(Atomic Energy of Canada Limited)and the arched tunnel.Although the Mine-by and arched tunnels were numerically simulated based on the mobilized dilation angle model,the variability associated with dilation angle around the simulated Mine-by and arched tunnels is insignificant,and dilation angle is approximately constant in the plastic zone.
基金Project(S2598445)supported by the Project for Cooperative R&D between Industry,Academy and Research Institute Funded by the Korea Ministry of SME and Startups in 2018
文摘In this study,we present the characterization of the carbon fibers recovered from the mechanochemical-enhanced recycling of carbon fiber reinforced fibers.The objectives of the study were to investigate the effect of our modified recycling method on the interfacial properties of recovered fibers.The reinforced plastics were recycled;the recycling efficiency was determined and the recovered fibers were sized using 1 wt%and 3 wt%concentration of(3-aminopropyl)triethoxysilane.We characterized the morphologies utilizing the electron spectroscopy for chemical analysis(ESCA),atomic force microscopy(AFM),FTIR-attenuated total reflection(ATR)spectroscopy and scanning electron microscopy(SEM).Although the surface of the fibers had no cracks,there was evidence of contaminations which affected the interfacial properties and the quality of the fibers.Results showed that the trends in the recovered and virgin fibers were similar with an increase in sizing concentration.The results highlighted the perspectives of increasing the quality of recovered fibers after the recycling process.
基金Project(07JJ3102) supported by Hunan Provincial Natural Science Foundation,ChinaProject(k0902132-11) supported by Changsha Municipal Science and Technology,China
文摘Based on the pseudo potential plane-wave method of density functional theory （DFT）, Ti1-xNbxAk （x=0, 0.062 5, 0.083 3, 0.125, 0.250） crystals＇ geometry structure, elastic constants, electronic structure and Mulliken populations were calculated, and the effects of doping on the geometric structure, electronic structure and bond strength were systematically analyzed. The results show that the influence of Nb on the geometric structure is little in terms of the plasticity, and with the increase of Nb content, the covalent bond strength remarkably reduces, and Ti-Al, Nb-M （M=Ti, Al） and other hybrid bonds enhance; meanwhile, the peak district increases and the pseudo-energy gap first decreases and then increases, the overall band structure narrows, the covalent bond and direction of bonds reduce. The population analysis also shows that the results are consistent with the electronic structure analysis. The density of states of TiAINb shows that Nb doping can enhance the activity of Al and benefit the form of Al2O3 film. All the calculations reveal that the room temperature plasticity and the antioxidation properties of the compounds can be improved with the Nb content of 8.33%-12.5% （mole fraction）.
基金Project(20122BAB206014)supported by National Natural Science Foundation of ChinaProject(51365038)supported by the Natural Science Foundation of Jiangxi Province,ChinaProject(GJJ13068)supported by the Science and Technology Program of Educational Committee of Jiangxi Province,China
文摘The effects of process parameters in rapid heat cycle moulding （RHCM） on parts warpage were investigated. A vehicle-used blue-tooth front shell （consisting of ABS material） was considered as a part example manufactured by RHCM method. The corresponding rapid heat response mould with an innovational conformal heating/cooling channel system and a dynamic mould temperature control system based on the Jll-W-160 type precise temperature controller was proposed. During heating/cooling process, the mould was able to be heated from room temperature to 160 ~C in 6 s and then cooled to 80 ~C in 22 s. The effects of processing conditions in RHCM on part warpage were investigated based on the single factor experimental method and Taguchi theory. Results reveal that the elevated mould temperature reduces unwanted freezing during the injection stage, thus improving mouldability and enhancing part quality, whereas the overheated of mould temperature will lead to defective product. The feasible mould temperature scope in RHCM should be no higher than 140 ~C, and the efficient mould temperature scope should be around the polymer heat distortion temperature. Melt temperature as well as injection pressure effects on warpage can be divided into two stages The lower stage gives a no explicit effect on warpage whereas the higher stage leads to a quasi-linear downtrend. But others affect the warpage as a V-type fluctuation, reaching to the minimum around the heat distortion temperature. Under the same mould temperature condition, the effects of process parameters on warpage decrease according to the following order, packing time, packing pressure, melt temperature, injection pressure and cooling time, respectively.
基金Supported by the Fund of Science and Technology Research Project of the 12th Five-year Plan(2012BAD32B02-5)
文摘In order to improve the properties of rice straw fiber film, one factor contrast test method was employed. Plasticizer type was chosen as input variable, dry tension strength and elongation, wet tension strength and elongation, bursting strength and tearing strength were chosen as indexes. The results showed that there were significant differences among the means of dry tension strength, dry elongation and bursting strength of different plasticizers; there were not significant differences among the means of wet tension strength, wet elongation and tearing strength of different plasticizers; for dry tension strength and elongation, glycerol had a significant difference with sorbitol and PEG, no significant difference was observed between sorbitol and PEG, dry tension strength added glycerol had been reduced 6.8% compared with that added sorbitol, reduced 9.5% compared with that added PEG; elongation had been improved 6.1% and 9.4%, respectively; for bursting strength, sorbitol had a significant difference with glycerol and PEG, no significant difference was observed between glycerol and PEG; bursting strength added glycerol and added PEG had been improved 6.9% and 5.6%, respectively compared with that of the added sorbitol. The results provided a theoretical reference for further improving the straw fiber film manufacturing process.
基金Project(11B033)supported by the Foundation for Excellent Young Scholars of Hunan Scientific Committee,ChinaProject(116001)supported by the Consultative Program of the Chinese Academy of Engineering+1 种基金Project(11JJ6040)supported by the National Natural Science Foundation of Hunan Province,ChinaProject(2010GK3198)supported by the Science and Research Program of Hunan Province,China
文摘Rehabilitation of existing structures with fiber reinforced plastic(FRP)has been growing in popularity because they offer superior performance in terms of resistance to corrosion and high specific stiffness.The strain coordination results of 34 reinforced concrete beams(four groups)strengthened with different methods were presented including external-bonded or near-surface mounted glass or carbon FRP or helical rib bar in order to study the strain coordination of the strengthening materials and steel rebar of RC beam.Because there is relative slipping between concrete and strengthening materials(SM),the strain of SM and steel rebar of RC beam satisfies the double linear strain distribution assumption,that is,the strain of longitudinal fiber parallel to the neutral axis of plated beam within the scope of effective height(h0)of the cross section is in direct proportion to the distance from the fiber to the neutral axis.The strain of SM and steel rebar satisfies the equation εGCH=βεsteel,where the value of β is equal to 1.1-1.3 according to the test results.
基金Project(51074052)supported by the National Natural Science Foundation of ChinaProject(BK20140334)supported by the Basic Research Program of Jiangsu Province+2 种基金ChinaProject(14KJB460024)supported by the Natural Science Foundation of Jiangsu Higher Education Institutions of ChinaProject(2014M561707)supported by China Postdoctoral Science Foundation
文摘In order to overcome the nonlinearity of Mises criterion, a new linear yield criterion with a dodecagon shape of the same perimeter as Mises criterion was derived by means of geometrical analysis. Its specific plastic work rate expressed as a linear function of the yield stress, the maximum and minimum strains was also deduced and compared with that of Mises criterion. The physical meaning of the proposed yield criterion is that yielding of materials begins when the shear yield stress τs reaches the magnitude of 0.594σs. By introducing the Lode parameter, validation of evolution expressions of the proposed yield criterion with those based on Tresca, Mises and TSS criteria as well as available classical yield experimental results of various metals shows that the present results intersect with Mises results and coincide well with experimental data. Moreover, further application to the limit analysis of circle plate as an example is performed to demonstrate the effectiveness of the proposed yield criterion, and the subsequent comparison of limit loads with the Tresca analytical solutions and Mises numerical results shows that the present results are higher than the Tresca analytical results, and are in good agreement with the Mises numerical results.
