Graphite oxide(GO) was prepared by the pressurized oxidation method and incorporated into polyimide(PI) matrix to fabricate high-k composite films by in-situ polymerization and subsequent thermal treatment. The result...Graphite oxide(GO) was prepared by the pressurized oxidation method and incorporated into polyimide(PI) matrix to fabricate high-k composite films by in-situ polymerization and subsequent thermal treatment. The results show that the as-prepared GO had good dispersion and compatibility in PI matrix due to the introduction of abundant oxygen-containing functional groups during the oxidation. The residual graphitic domains and the thermal treatment induced reduction of GO further enhanced the dielectric permittivity of the resulting GO–PI composites. The dielectric permittivity of the GO–PI composites exhibited a typical percolation behavior with a percolation threshold of 0.0347 of volume ratio and a critical exponent of 0.837. Near the percolation threshold, the dielectric permittivity of the GO–PI composite increased to 108 at 10~2 Hz and was 26 times that of the pure PI.展开更多
In this paper, a new numerical method-Kuhn algorithm with contour integral-is intrroduced and used to calculate the complex dielectric permittivities of materials from the short-circuitedwaveguide measurements. Some n...In this paper, a new numerical method-Kuhn algorithm with contour integral-is intrroduced and used to calculate the complex dielectric permittivities of materials from the short-circuitedwaveguide measurements. Some numerical results are given to verify the validity and efficiency ofthe new numerical method and the complex dielectric permittivities of materials calculated by thenew numerical method are quite identical with the results given by other works.展开更多
The CaCu3Ti4O12 xerogels, powders and ceramics were prepared through the sol-gel method using two kinds of organic acid （decanoic acid and decanedioic acid）. The xerogels, powders and ceramics were characterized by ...The CaCu3Ti4O12 xerogels, powders and ceramics were prepared through the sol-gel method using two kinds of organic acid （decanoic acid and decanedioic acid）. The xerogels, powders and ceramics were characterized by the methods of TG-DTG, FT-IR, XRD, SEM and TEM. The dielectric properties of the ceramics were also measured. The results indicated that the powders calcined at 850 ℃ for 2 h are both nanometer scale particles. After sintering, the ceramics mainly consist of the CaCu3Ti4O12 phase. Compared with the powders prepared using monoacid, the particle size of the powders prepared using diacid obviously increases, and the grain size, the relative density and the whole permittivity of the ceramics increase as well. Specially, the ceramic prepared using decanedioic acid has higher relative density （97.3%）, dielectric constant （316 808） and lower dielectric loss （0.242 5） at 30 ℃ （10 kIaz）展开更多
The dielectric constant(DC)is one of the key properties for detection of threat materials such as Improvised Explosive Devices(IEDs).In the present paper,the density functional theory(DFT)as well as ab-initio approach...The dielectric constant(DC)is one of the key properties for detection of threat materials such as Improvised Explosive Devices(IEDs).In the present paper,the density functional theory(DFT)as well as ab-initio approaches are used to explore effective methods to predict dielectric constants of a series of 12 energetic materials(EMs)for which experimental data needed to experimentally determine the dielectric constant(refractive indices)are available.These include military grades energetic materials,nitro and peroxide compounds,and the widely used nitroglycerin.Ab-initio and DFT calculations are conducted.In order to calculate dielectric constant values of materials,potential DFT functional combined with basis sets are considered for testing.Accuracy of the calculations are compared to experimental data listed in the scientific literature,and time required for calculations are both evaluated and discussed.The best functional/basis set combinations among those tested are CAM-B3LYP and AUG-ccpVDZm,which provide great results,with accuracy deviations below 5%when calculated results are compared to experimental data.展开更多
Left-hand materials have drawn increasing attention from many disciplines and found widespread application, especially in microwave engineering. A sandwiched metamaterial consisting of multi-nested square-split-ring r...Left-hand materials have drawn increasing attention from many disciplines and found widespread application, especially in microwave engineering. A sandwiched metamaterial consisting of multi-nested square-split-ring resonators on the top side and a set of wires on the back side is proposed. Scattering parameters are retrieved by high-frequency structure simulator(HFSS) software based on the finite element method. Effects of square-split-ring number on the left-hand characteristics containing negative values of permittivity, permeability, and refractive index have been intensively investigated. Simulated results show that obvious resonant left-hand characteristics could be observed within 8-18 GHz, and the resonant frequency counts are inclined to be in direct proportion to the square-split-ring number over 8-18 GHz. Besides, the proposed sandwiched metamaterial with three square-split-ring resonators and three wires presents the widest frequency band of left-hand characteristics in a range of 8-18 GHz. Further, electromagnetic field distributions demonstrated that the induced magnetic dipole dominates the resonant absorption. The multi-peak resonance characteristics of square-split-ring resonant structure are considered to be a promising candidate for selective-frequency absorption or modulation toward microwave frequency band.展开更多
The oil-pressboard insulation is a typical composite insulation system widely used in the design and manufactory of large power apparatus. The implement of oil-pressboard insulation may lead to surface electrification...The oil-pressboard insulation is a typical composite insulation system widely used in the design and manufactory of large power apparatus. The implement of oil-pressboard insulation may lead to surface electrification and discharge at the interface under certain condition. It is of significant importance to take an insight into the phenomenon occurring at the interface. Through experiment, the pressboard is found as a porous material. The interface changes abruptly from bulk pressboard to the bulk oil as a result of the porous structure. A new model is proposed which divides the interface into bulk oil region, transition region, and bulk pressboard region. The width of the transition region is decided according to the microtome figure. The effective permittivity of the transition region is calculated using a new model based on fractal theory. The model is validated and compared with previous calculation model. The effect of the existence of transition region on the electric field distribution is discussed.展开更多
基金Project(2013JSJJ002)supported by the Faculty Research Fund of Central South University,China
文摘Graphite oxide(GO) was prepared by the pressurized oxidation method and incorporated into polyimide(PI) matrix to fabricate high-k composite films by in-situ polymerization and subsequent thermal treatment. The results show that the as-prepared GO had good dispersion and compatibility in PI matrix due to the introduction of abundant oxygen-containing functional groups during the oxidation. The residual graphitic domains and the thermal treatment induced reduction of GO further enhanced the dielectric permittivity of the resulting GO–PI composites. The dielectric permittivity of the GO–PI composites exhibited a typical percolation behavior with a percolation threshold of 0.0347 of volume ratio and a critical exponent of 0.837. Near the percolation threshold, the dielectric permittivity of the GO–PI composite increased to 108 at 10~2 Hz and was 26 times that of the pure PI.
文摘In this paper, a new numerical method-Kuhn algorithm with contour integral-is intrroduced and used to calculate the complex dielectric permittivities of materials from the short-circuitedwaveguide measurements. Some numerical results are given to verify the validity and efficiency ofthe new numerical method and the complex dielectric permittivities of materials calculated by thenew numerical method are quite identical with the results given by other works.
基金Projects(CC20120031,CC20110048)supported by Changzhou Science and Technology Innovation Project,China
文摘The CaCu3Ti4O12 xerogels, powders and ceramics were prepared through the sol-gel method using two kinds of organic acid （decanoic acid and decanedioic acid）. The xerogels, powders and ceramics were characterized by the methods of TG-DTG, FT-IR, XRD, SEM and TEM. The dielectric properties of the ceramics were also measured. The results indicated that the powders calcined at 850 ℃ for 2 h are both nanometer scale particles. After sintering, the ceramics mainly consist of the CaCu3Ti4O12 phase. Compared with the powders prepared using monoacid, the particle size of the powders prepared using diacid obviously increases, and the grain size, the relative density and the whole permittivity of the ceramics increase as well. Specially, the ceramic prepared using decanedioic acid has higher relative density （97.3%）, dielectric constant （316 808） and lower dielectric loss （0.242 5） at 30 ℃ （10 kIaz）
文摘The dielectric constant(DC)is one of the key properties for detection of threat materials such as Improvised Explosive Devices(IEDs).In the present paper,the density functional theory(DFT)as well as ab-initio approaches are used to explore effective methods to predict dielectric constants of a series of 12 energetic materials(EMs)for which experimental data needed to experimentally determine the dielectric constant(refractive indices)are available.These include military grades energetic materials,nitro and peroxide compounds,and the widely used nitroglycerin.Ab-initio and DFT calculations are conducted.In order to calculate dielectric constant values of materials,potential DFT functional combined with basis sets are considered for testing.Accuracy of the calculations are compared to experimental data listed in the scientific literature,and time required for calculations are both evaluated and discussed.The best functional/basis set combinations among those tested are CAM-B3LYP and AUG-ccpVDZm,which provide great results,with accuracy deviations below 5%when calculated results are compared to experimental data.
基金Project(2017YFA0204600)supported by the National Key Research and Development Program of ChinaProject(51802352)supported by the National Natural Science Foundation of ChinaProject(2019JJ50768)supported by the Natural Science Foundation of Hunan Province of China。
文摘Left-hand materials have drawn increasing attention from many disciplines and found widespread application, especially in microwave engineering. A sandwiched metamaterial consisting of multi-nested square-split-ring resonators on the top side and a set of wires on the back side is proposed. Scattering parameters are retrieved by high-frequency structure simulator(HFSS) software based on the finite element method. Effects of square-split-ring number on the left-hand characteristics containing negative values of permittivity, permeability, and refractive index have been intensively investigated. Simulated results show that obvious resonant left-hand characteristics could be observed within 8-18 GHz, and the resonant frequency counts are inclined to be in direct proportion to the square-split-ring number over 8-18 GHz. Besides, the proposed sandwiched metamaterial with three square-split-ring resonators and three wires presents the widest frequency band of left-hand characteristics in a range of 8-18 GHz. Further, electromagnetic field distributions demonstrated that the induced magnetic dipole dominates the resonant absorption. The multi-peak resonance characteristics of square-split-ring resonant structure are considered to be a promising candidate for selective-frequency absorption or modulation toward microwave frequency band.
基金Project(2009CB724504)supported by the National Basic Research Program of China
文摘The oil-pressboard insulation is a typical composite insulation system widely used in the design and manufactory of large power apparatus. The implement of oil-pressboard insulation may lead to surface electrification and discharge at the interface under certain condition. It is of significant importance to take an insight into the phenomenon occurring at the interface. Through experiment, the pressboard is found as a porous material. The interface changes abruptly from bulk pressboard to the bulk oil as a result of the porous structure. A new model is proposed which divides the interface into bulk oil region, transition region, and bulk pressboard region. The width of the transition region is decided according to the microtome figure. The effective permittivity of the transition region is calculated using a new model based on fractal theory. The model is validated and compared with previous calculation model. The effect of the existence of transition region on the electric field distribution is discussed.
