Gradiently denitrated gun propellant(GDGP)prepared by a“gradient denitration”strategy is obviously superior in progressive burning performance to the traditional deterred gun propellant.Currently,the preparation of ...Gradiently denitrated gun propellant(GDGP)prepared by a“gradient denitration”strategy is obviously superior in progressive burning performance to the traditional deterred gun propellant.Currently,the preparation of GDGP employed a tedious two-step method involving organic solvents,which hinders the large-scale preparation of GDGP.In this paper,GDGP was successfully prepared via a novelty and environmentally friendly one-step method.The obtained samples were characterized by FT-IR,Raman,SEM and XPS.The results showed that the content of nitrate groups gradiently increased from the surface to the core in the surface layer of GDGP and the surface layer of GDGP exhibited a higher compaction than that of raw gun propellant,with a well-preserved nitrocellulose structure.The denitration process enabled the propellant surface with regressive energy density and good progressive burning performance,as confirmed by oxygen bomb and closed bomb test.At the same time,the effects of different solvents on the component loss of propellant were compared.The result showed that water caused the least component loss.Finally,the stability of GDGP was confirmed by methyl-violet test.This work not only provided environmentally friendly,simple and economic preparation of GDGP,but also confirmed the stability of GDGP prepared by this method.展开更多
This work presents a method to solve the weak solubility of zinc chloride(ZnCl_2) in the ethanol by adding some reasonable water into an ethanol electrolyte containing ZnCl_2 and myristic acid(CH_3(CH_2)_(12)COOH).A r...This work presents a method to solve the weak solubility of zinc chloride(ZnCl_2) in the ethanol by adding some reasonable water into an ethanol electrolyte containing ZnCl_2 and myristic acid(CH_3(CH_2)_(12)COOH).A rapid one-step electrodeposition process was developed to fabricate anodic(2.5 min) and cathodic(40 s) superhydrophobic surfaces of copper substrate(contact angle more than 150°) in an aqueous ethanol electrolyte.Morphology,composition,chemical structure and superhydrophobicity of these superhydrophobic surfaces were investigated by SEM,FTIR,XRD,and contact angle measurement,respectively.The results indicate that water ratio of the electrolyte can reduce the required deposition time,superhydrophobic surface needs over 30 min with anhydrous electrolyte,while it needs only 2.5 min with electrolyte including 10 mL water,and the maximum contact angle of anodic surface is 166° and that of the cathodic surface is 168°.Two copper electrode surfaces have different reactions in the process of electrodeposition time,and the anodic copper surface covers copper myristate(Cu[CH_3(CH_2)_(12)COO]_2) and cupric chloride(CuCl);while,zinc myristate(Zn[CH_3(CH_2)_(12)COO]_2) and pure zinc(Zn) appear on the cathodic surface.展开更多
A new technology of one-step leaching of refractory gold concentrate containing arsenic and sulfur was studied and 96. 8% of gold was extracted in an hour by this technology. Themodynamic possibility of reactions of a...A new technology of one-step leaching of refractory gold concentrate containing arsenic and sulfur was studied and 96. 8% of gold was extracted in an hour by this technology. Themodynamic possibility of reactions of arsenopyrite. pyrite and gold with sodium hypochlorite in NaOH medium, and solution chemistry of H3AuO3 at different pH values were analyzed. The reason why the gold wrapped by FeAsS, FeS2 can be leached out rapidly by grnding of porcelain ball mill. is explained.展开更多
Sulfide solid electrolytes(S-SEs)are widely preferred for their high ionic conductivity and processability.However,the further development of S-SEs is hindered by the excessive price of its critical raw materials of L...Sulfide solid electrolytes(S-SEs)are widely preferred for their high ionic conductivity and processability.However,the further development of S-SEs is hindered by the excessive price of its critical raw materials of Li_(2)S.Herein,a low-cost and environmentally friendly method is proposed to synthesize Li_(2)S by the carbothermal reduction reaction of Li_(2)SO_(4)in one step,and the effects of various factors are also discussed.As a result,a purity of 99.67%is obtained over the self-prepared Li_(2)S.More importantly,the cost of the self-prepared Li_(2)S is only about 50$/kg,which is significantly lower than that of the commercial counterpart(10000−15000 dollar/kg).Moreover,the ionic conductivity of Li_(5.5)PS_(4.5)Cl_(1.5)prepared using self-prepared Li_(2)S as raw materials is 4.19 mS/cm at room temperature,which is a little higher than that of Li_(5.5)PS_(4.5)Cl_(1.5)using commercial Li_(2)S(4.05 mS/cm).And the all-solid-state lithium batteries(ASSLBs)with the as-prepared electrolytes could maintain a discharge capacity of 109.9 mA·h/g with an average coulombic efficiency(CE)of 98%after 100 cycles at 0.2 C,which is equivalent to that using commercial Li_(2)S,demonstrating that the preparation strategy of Li_(2)S proposed in this work is feasible.展开更多
文摘Gradiently denitrated gun propellant(GDGP)prepared by a“gradient denitration”strategy is obviously superior in progressive burning performance to the traditional deterred gun propellant.Currently,the preparation of GDGP employed a tedious two-step method involving organic solvents,which hinders the large-scale preparation of GDGP.In this paper,GDGP was successfully prepared via a novelty and environmentally friendly one-step method.The obtained samples were characterized by FT-IR,Raman,SEM and XPS.The results showed that the content of nitrate groups gradiently increased from the surface to the core in the surface layer of GDGP and the surface layer of GDGP exhibited a higher compaction than that of raw gun propellant,with a well-preserved nitrocellulose structure.The denitration process enabled the propellant surface with regressive energy density and good progressive burning performance,as confirmed by oxygen bomb and closed bomb test.At the same time,the effects of different solvents on the component loss of propellant were compared.The result showed that water caused the least component loss.Finally,the stability of GDGP was confirmed by methyl-violet test.This work not only provided environmentally friendly,simple and economic preparation of GDGP,but also confirmed the stability of GDGP prepared by this method.
基金Projects(11304243,11102164)supported by the National Natural Science Foundation of ChinaProject(2014JQ1039)supported by the Natural Science Foundation of Shannxi Province,China+3 种基金Project(12JK0966)supported by the Shaanxi Provincial Education Department,ChinaProject(2013QDJ037)supported by the Xi’an University of Science and Technology Dr Scientific Research Fund,ChinaProject(3102016ZY027)supported by the Fundamental Research Funds for the Central Universities of ChinaProject(13GH014602)supported by the Program of New Staff and Research Area Project of NPU,China
文摘This work presents a method to solve the weak solubility of zinc chloride(ZnCl_2) in the ethanol by adding some reasonable water into an ethanol electrolyte containing ZnCl_2 and myristic acid(CH_3(CH_2)_(12)COOH).A rapid one-step electrodeposition process was developed to fabricate anodic(2.5 min) and cathodic(40 s) superhydrophobic surfaces of copper substrate(contact angle more than 150°) in an aqueous ethanol electrolyte.Morphology,composition,chemical structure and superhydrophobicity of these superhydrophobic surfaces were investigated by SEM,FTIR,XRD,and contact angle measurement,respectively.The results indicate that water ratio of the electrolyte can reduce the required deposition time,superhydrophobic surface needs over 30 min with anhydrous electrolyte,while it needs only 2.5 min with electrolyte including 10 mL water,and the maximum contact angle of anodic surface is 166° and that of the cathodic surface is 168°.Two copper electrode surfaces have different reactions in the process of electrodeposition time,and the anodic copper surface covers copper myristate(Cu[CH_3(CH_2)_(12)COO]_2) and cupric chloride(CuCl);while,zinc myristate(Zn[CH_3(CH_2)_(12)COO]_2) and pure zinc(Zn) appear on the cathodic surface.
文摘A new technology of one-step leaching of refractory gold concentrate containing arsenic and sulfur was studied and 96. 8% of gold was extracted in an hour by this technology. Themodynamic possibility of reactions of arsenopyrite. pyrite and gold with sodium hypochlorite in NaOH medium, and solution chemistry of H3AuO3 at different pH values were analyzed. The reason why the gold wrapped by FeAsS, FeS2 can be leached out rapidly by grnding of porcelain ball mill. is explained.
基金Project(52374407)supported by the National Natural Science Foundation of China。
文摘Sulfide solid electrolytes(S-SEs)are widely preferred for their high ionic conductivity and processability.However,the further development of S-SEs is hindered by the excessive price of its critical raw materials of Li_(2)S.Herein,a low-cost and environmentally friendly method is proposed to synthesize Li_(2)S by the carbothermal reduction reaction of Li_(2)SO_(4)in one step,and the effects of various factors are also discussed.As a result,a purity of 99.67%is obtained over the self-prepared Li_(2)S.More importantly,the cost of the self-prepared Li_(2)S is only about 50$/kg,which is significantly lower than that of the commercial counterpart(10000−15000 dollar/kg).Moreover,the ionic conductivity of Li_(5.5)PS_(4.5)Cl_(1.5)prepared using self-prepared Li_(2)S as raw materials is 4.19 mS/cm at room temperature,which is a little higher than that of Li_(5.5)PS_(4.5)Cl_(1.5)using commercial Li_(2)S(4.05 mS/cm).And the all-solid-state lithium batteries(ASSLBs)with the as-prepared electrolytes could maintain a discharge capacity of 109.9 mA·h/g with an average coulombic efficiency(CE)of 98%after 100 cycles at 0.2 C,which is equivalent to that using commercial Li_(2)S,demonstrating that the preparation strategy of Li_(2)S proposed in this work is feasible.
