The microstructure and magnetic properties of Fe_(40)Co_(40)Zr_(9)B_(10)Ge_(1)(Mo-free)and Fe_(40)Co_(40)Zr_(5)Mo_(4)B_(10)Ge_(1)(Mocontaining)nanocrystalline alloys,prepared using an amorphous crystallization method,...The microstructure and magnetic properties of Fe_(40)Co_(40)Zr_(9)B_(10)Ge_(1)(Mo-free)and Fe_(40)Co_(40)Zr_(5)Mo_(4)B_(10)Ge_(1)(Mocontaining)nanocrystalline alloys,prepared using an amorphous crystallization method,were investigated.Mo addition affects the crystallization of the Fe_(40)Co_(40)Zr_(9)B_(10)Ge_(1) amorphous alloy and decreases the grain size of theα-Fe(Co)phase below 650℃.For the Mo-free alloy annealed at 600℃ and the Mo-containing alloy annealed at 575℃,with a singleα-Fe(Co)crystallization phase and approximately similar crystallization volume fractions,the Mo-containing alloy showed smaller,more regularly shaped grains and a significantly narrower grain-size distribution than the Mo-free alloy.The Fe and Co contents in the nanograins of the two alloys also differed.For the Mo-free alloy,a higher concentration of Co distributed in the residual amorphous matrix.For the Mo-containing alloy,a higher concentration Co dissolved in the nanograins.The specific saturation magnetization and coercivity of the Mo-free alloy were 1.05-and 1.59-times higher than those of the Mo-containing alloy,respectively.展开更多
The difference in microstructure leads to the diversity of shale mechanical properties and bedding fractures distribution patterns.In this paper,the microstructure and mechanical properties of Longmaxi marine shale an...The difference in microstructure leads to the diversity of shale mechanical properties and bedding fractures distribution patterns.In this paper,the microstructure and mechanical properties of Longmaxi marine shale and Qingshankou continental shale were studied by X-ray diffractometer(XRD),field emission scanning electron microscope(FE-SEM)with mineral analysis system,and nanoindentation.Additionally,the typical bedding layers area was properly stratified using Focused Ion Beam(FIB),and the effects of microstructure and mechanical properties on the distribution patterns of bedding fractures were analyzed.The results show that the Longmaxi marine shale sample contains more clay mineral grains,while the Qingshankou continental shale sample contains more hard brittle mineral grains such as feldspar.For Longmaxi marine shale sample,hard brittle minerals with grain sizes larger than 20μm is18.24%and those with grain sizes smaller than 20μm is 16.22%.For Qingshankou continental shale sample,hard brittle minerals with grain sizes larger than 20μm is 40.7%and those with grain sizes smaller than 20μm is 11.82%.In comparison to the Qingshankou continental shale sample,the Longmaxi marine shale sample has a lower modulus,hardness,and heterogeneity.Laminated shales are formed by alternating coarse-grained and fine-grained layers during deposition.The average single-layer thickness of Longmaxi marine shale sample is greater than Qingshankou continental shale sample.The two types of shale have similar bedding fractures distribution patterns and fractures tend to occur in the transition zone from coarse-grained to fine-grained deposition.The orientation of the fracture is usually parallel to the bedding plane and detour occurs in the presence of hard brittle grains.The fracture distribution density of the Longmaxi marine shale sample is lower than that of the Qingshankou continental shale sample due to the strong heterogeneity of the Qingshankou continental shale.The current research provides guidelines for the effective development of shale reservoirs in various sedimentary environments.展开更多
Compared to the commercial soft-magnetic alloys,the high saturation magnetic flux density(Bs)and low coercivity(Hc)of post-developed novel nanocrystalline alloys tend to realize the miniaturization and lightweight of ...Compared to the commercial soft-magnetic alloys,the high saturation magnetic flux density(Bs)and low coercivity(Hc)of post-developed novel nanocrystalline alloys tend to realize the miniaturization and lightweight of electronic products,thus attracting great attention.In this work,we designed a new FeNiBCuSi formulation with a novel atomic ratio,and the microstructure evolution and magnetic softness were investigated.Microstructure analysis revealed that the amount of Si prompted the differential chemical fluctuations of Cu element,favoring the different nucleation and growth processes ofα-Fe nanocrystals.Furthermore,microstructural defects associated with chemical heterogeneities were unveiled using the Maxwell-Voigt model with two Kelvin units and one Maxwell unit based on creeping analysis by nanoindentation.The defect,with a long relaxation time in relaxation spectra,was more likely to induce the formation of crystal nuclei that ultimately evolved into theα-Fe nanocrystals.As a result,Fe_(84)Ni_(2)B_(12.5)Cu_(1)Si_(0.5)alloy with refined uniform nanocrystalline microstructure exhibited excellent magnetic softness,including a high B_(s)of 1.79 T and very low H_(c)of 2.8 A/m.Our finding offers new insight into the influence of activated defects associated with chemical heterogeneities on the microstructures of nanocrystalline alloy with excellent magnetic softness.展开更多
A reasonable heat treatment process for TC4 ELI titanium alloy is crucial to tune microstructures to improve its explosion resistance.However,there is limited investigation on tuning microstructures of TC4 ELI to impr...A reasonable heat treatment process for TC4 ELI titanium alloy is crucial to tune microstructures to improve its explosion resistance.However,there is limited investigation on tuning microstructures of TC4 ELI to improve explosion resistance.Moreover,the current challenge is quantifying microstructural changes'effects on explosion resistance and incorporating microstructural changes into finite element models.This work aims to tune microstructures to improve explosion resistance and elucidate their anti-explosion mechanism,and find a suitable method to incorporate microstructural changes into finite element models.In this work,we systematically study the deformation and failure characteristics of TC4 ELI plates with varying microstructures using an air explosion test and LS-DYNA finite element modeling.The Johnson-Cook(JC)constitutive parameters are used to quantify the effects of microstructural changes on explosion resistance and incorporate microstructural changes into finite element models.Because of the heat treatment,one plate has equiaxed microstructure and the other has bimodal microstructure.The convex of the plate after the explosion has a quadratic relationship with the charge mass,and the simulation results demonstrate high reliability,with the error less than 17.5%.Therefore,it is feasible to obtain corresponding JC constitutive parameters based on the differences in microstructures and mechanical properties and characterize the effects of microstructural changes on explosion resistance.The bimodal target exhibits excellent deformation resistance.The response of bimodal microstructure to the shock wave may be more intense under explosive loading.The well-coordinated structure of the bimodal target enhances its resistance to deformation.展开更多
The high entropy alloys(HEAs)are the newly developed high-performance materials that have gained significant importance in defence,nuclear and aerospace sector due to their superior mechanical properties,heat resistan...The high entropy alloys(HEAs)are the newly developed high-performance materials that have gained significant importance in defence,nuclear and aerospace sector due to their superior mechanical properties,heat resistance,high temperature strength and corrosion resistance.These alloys are manufactured by the equal mixing or larger proportions of five or more alloying elements.HEAs exhibit superior mechanical performance compared to traditional engineering alloys because of the extensive alloying composition and higher entropy of mixing.Solid state welding(SSW)techniques such as friction stir welding(FSW),rotary friction welding(RFW),diffusion bonding(DB)and explosive welding(EW)have been efficiently deployed for improving the microstructural integrity and mechanical properties of welded HEA joints.The HEA interlayers revealed greater potential in supressing the formation of deleterious intermetallic phases and maximizing the mechanical properties of HEAs joints.The similar and dissimilar joining of HEAs has been manifested to be viable for HEA systems which further expands their industrial applications.Thus,the main objective of this review paper is to present a critical review of current state of research,challenges and opportunities and main directions in SSW of HEAs mainly CoCrFeNiMn and Al_xCoCrFeNi alloys.The state of the art of problems,progress and future outlook in SSW of HEAs are critically reviewed by considering the formation of phases,microstructural evolution and mechanical properties of HEAs joints.展开更多
Generally,layered Ni-rich cathode materials exhibit the morphology of polycrystalline secondary sphere composed of numerous primary particles.While the arrangement of primary particles plays a very important role in t...Generally,layered Ni-rich cathode materials exhibit the morphology of polycrystalline secondary sphere composed of numerous primary particles.While the arrangement of primary particles plays a very important role in the properties of Ni-rich cathodes.The disordered particle arrangement is harmful to the cyclic performance and structural stability,yet the fundamental understanding of disordered structure on the structural degradation behavior is unclarified.Herein,we have designed three kinds of LiNi_(0.83)Co_(0.06)Mn_(0.11)O_(2) cathode materials with different primary particle orientations by regulating the precursor coprecipitation process.Combining finite element simulation and in-situ characterization,the Li^(+)transport and structure evolution behaviors of different materials are unraveled.Specifically,the smooth Li^(+)diffusion minimizes the reaction heterogeneity,homogenizes the phase transition within grains,and mitigates the anisotropic microstructural change,thereby modulating the crack evolution behavior.Meanwhile,the optimized structure evolution ensures radial tight junctions of the primary particles,enabling enhanced Li^(+)diffusion during dynamic processes.Closed-loop bidirectional enhancement mechanism becomes critical for grain orientation regulation to stabilize the cyclic performance.This precursor engineering with particle orientation regulation provides the useful guidance for the structural design and feature enhancement of Ni-rich layered cathodes.展开更多
Molecular dynamics(MD)simulations are employed to delve into the multifaceted effects of TiB_(2) nanoparticles on the intricate grain refinement mechanism,microstructural evolution,and tensile performance of Inconel 7...Molecular dynamics(MD)simulations are employed to delve into the multifaceted effects of TiB_(2) nanoparticles on the intricate grain refinement mechanism,microstructural evolution,and tensile performance of Inconel 718 superalloys during the rapid directional solidification.Specifically,the study focuses on elucidating the role of TiB2 nanoparticles in augmenting the nucleation rate during the rapid directional solidification process of Ni_(60)Cr_(21)Fe_(19) alloy system.Furthermore,subsequent tensile simulations are conducted to comprehensively evaluate the anisotropic behavior of tensile properties within the solidified microstructures.The MD results reveal that the incorporation of TiB₂nanoparticles during the rapid directional solidification of the Ni_(60)Cr_(21)Fe_(19) significantly enhances the average nucleation rate,escalating it from 1.27×10^(34)m^(-3)·s^(-1)to 2.55×10^(34)m^(-3)·s^(-1).Notably,within the face centered cube(FCC)structure,Ni atoms exhibit pronounced compositional segregation,and the solidified alloy maintains an exceptionally high dislocation density reaching up to 10^(16)m^(-2).Crucially,the rapid directional solidification process imparts a distinct microstructural anisotropy,leading to a notable disparity in tensile strength.Specifically,the tensile strength along the solidification direction is markedly superior to that perpendicular to it.This disparity arises from different deformation mechanisms under varying loading orientations.Tensile stress perpendicular to the solidification direction encourages the formation of smooth and organized mechanical twins.These twins act as slip planes,enhancing dislocation mobility and thereby improving stress relaxation and dispersion.Moreover,the results underscore the profound strengthening effect of TiB_(2) nanoparticles,particularly in enhancing the tensile strength along the rapid directional solidification direction.展开更多
Combining theory and computation,we explore the Goos–H¨anchen(GH)effect for electrons in a single-layered semiconductor microstructure(SLSM)modulated by Dresselhaus spin–orbit coupling(SOC).GH displacement depe...Combining theory and computation,we explore the Goos–H¨anchen(GH)effect for electrons in a single-layered semiconductor microstructure(SLSM)modulated by Dresselhaus spin–orbit coupling(SOC).GH displacement depends on electron spins thanks to Dresselhaus SOC,therefore electron spins can be separated from the space domain and spinpolarized electrons in semiconductors can be realized.Both the magnitude and sign of the spin polarization ratio change with the electron energy,in-plane wave vector,strain engineering and semiconductor layer thickness.The spin polarization ratio approaches a maximum at resonance;however,no electron-spin polarization occurs in the SLSM for a zero in-plane wave vector.More importantly,the spin polarization ratio can be manipulated by strain engineering or semiconductor layer thickness,giving rise to a controllable spatial electron-spin splitter in the field of semiconductor spintronics.展开更多
The microstructural evolution and relaxation strengthening of nano-grained Ni annealed at a temperature range of 493–553 K were studied by in situ X-ray diffraction technique,transmission electron microscopy,and micr...The microstructural evolution and relaxation strengthening of nano-grained Ni annealed at a temperature range of 493–553 K were studied by in situ X-ray diffraction technique,transmission electron microscopy,and microhardness evaluation.Upon low-temperature annealing,the rather limited variations of anisotropic grain size and root-mean-square strain,conforming to an exponential relaxation model,yield a consistent activation energy of approximately 0.5 eV,which corresponds to the localized,rapid diffusion of excess vacancies on nonequilibrium surfaces/interfaces and/or defective lattice configurations.Microstructure examinations confirm the grain boundary ordering and excess defect reduction.The relaxation-induced strength enhancement can be attributed to the linear strengthening in the regime of small elastic lattice strains.This study provides an in-depth understanding of low-temperature nanostructural relaxation and its relation to strengthening.展开更多
The effects of rare earth Lanthanum on the microstructure, the physical property and the microhardness of Ag-Cu-Ti solder alloy are studied. Experimental results indicate that the addition of Lanthanum can evidently i...The effects of rare earth Lanthanum on the microstructure, the physical property and the microhardness of Ag-Cu-Ti solder alloy are studied. Experimental results indicate that the addition of Lanthanum can evidently improve the wettability and the microhardness of Ag-Cu-Ti solder alloy. Analysis results show that the increase in microhardness is related to the refining and uniform distribution of the intermetallic compounds. Proper content of Lanthanum added in Ag-Cu-Ti alloy solder can be controlled below 0.5% in mass percent.展开更多
The samples of brazed diamond grits with NiCr brazing alloy are prepared in vacuum and argon gas. The microstructures are analyzed with scanning electron microscope （SEM）, energy dispersive X-ray spectroscopy （EDS...The samples of brazed diamond grits with NiCr brazing alloy are prepared in vacuum and argon gas. The microstructures are analyzed with scanning electron microscope （SEM）, energy dispersive X-ray spectroscopy （EDS） and X-ray diffraction（XRD）. The effects of brazing atmospheres on the as-brazed NiCr brazing alloy composite structures and interracial microstructure are studied between diamond grits and brazing alloy. Results show that： （1） There are different composite structures of as-brazed NiCr brazing alloy under different oxygen partial pressures in vacuum and argon gas. B203 exists on the surface of the brazed samples under argon gas furnace brazing. It indicates that oxygen plays an important role in the resultants of as-brazed NiCr brazing alloy during the brazing process. （2） There are different interfacial microstructures in different brazing atmospheres, but the main reaction product is chromium carbides. The chromium carbides in argon gas furnace brazing grow in a disordered form, but those in vacuum furnace brazing grow radiated. And the scale of grains in argon gas is smaller than those in vacuum.展开更多
The Brownian dynamics （BD） simulation of a dilute surfactant solution is conducted in a steady shear flow. The rodlike micelle is assumed as a rigid rod composed of lined-up beads. A novel intercluster potential mod...The Brownian dynamics （BD） simulation of a dilute surfactant solution is conducted in a steady shear flow. The rodlike micelle is assumed as a rigid rod composed of lined-up beads. A novel intercluster potential model is introduced for describing the interactions between, micelles. In the model, the Lennard-Jones and the soft-sphere potentials are used as inter-bead potentials for end-end and interior-interior beads, respectively. The micelles are combined at their ends to form a network structure at lower shear rates and are disconnected to become more and more parallel to the shear flow direction with increasing shear rate. The change of micellar microstructures with the variation of the shear rate results in shear thinning characteristics of the computed shear viscosities and first normal stress difference coefficients. The effects of surfactant solution concentration on the micellar structures and rheological properties are also investigated. Results show that the shear viscosities and the first normal stress difference coefficients increase with increasing the viscosity of the surfactant solution.展开更多
The composition and sequence distribution of monomeric units in polyester polyether multiblock copolymer were studied by pyrolysis? gas chromatography (PGC) and pyrolysis gas chromatography/mass spectrometry (PGC/M...The composition and sequence distribution of monomeric units in polyester polyether multiblock copolymer were studied by pyrolysis? gas chromatography (PGC) and pyrolysis gas chromatography/mass spectrometry (PGC/MS). PGC was applied to study the F t curve of the multiblock copolymer and PGC/MS was used to separate and identify the pyrolyzates. DTA experiment was used to study the decomposition temperature. The results show that the beginning point of elastomer’s decomposition was about 300?℃ and the decomposition temperature of most of the sample was 550?℃. Many pyrolyzates were produced because of the breaking of weak bonds in the sample. The possible microstructure was verified and the pyrolysis pathway of the copolymer was investigated.展开更多
This paper is to study the influence of composition, microstructure and pore characteristics on the rock mechanical properties. Five kinds of sandstone compositions were analyzed by using X-ray diffraction instrument....This paper is to study the influence of composition, microstructure and pore characteristics on the rock mechanical properties. Five kinds of sandstone compositions were analyzed by using X-ray diffraction instrument. And the microstructure was observed by using scanning electron microscope. Then the pore distribution characteristic was investigated by using the low field nuclear magnetic resonance equipment. Finally, the uniaxial compression test was carried out to investigate the mechanical characteristics by using RMT150C mechanics experimental system and the uniaxial compressive strength, Poisson's ratio and elastic modulus were obtained. Compared to the analysis of the composition, structure and pore distribution and mechanical properties of the five kinds of sandstones, the relationship among composition,structure, pore distribution and mechanical properties was obtained. The results show that the composition, microstructure, pore distribution and mechanical properties of sandstone are closely related.With the decrease of feldspar and quartz particles, the compressive strength and elastic modulus increase, while the porosity decreases.展开更多
Microstructure of shale formation is the key to understanding its petrophysical and chemical properties.Optical microscopy, scanning electron microscopy and micro-computed tomography(μ-CT) have been combined for char...Microstructure of shale formation is the key to understanding its petrophysical and chemical properties.Optical microscopy, scanning electron microscopy and micro-computed tomography(μ-CT) have been combined for characterization of microstructure of Longmaxi(LMX)shale from Shizhu area, Sichan Basin. The results indicate that laminated LMX shale consists of mineral matrix-rich layers and organic matter(OM)-rich layers at micrometer scale in two and three dimensions. Mineral matrix layers,mainly consisting of interparticle pores and intraplatelet pores, are approximately parallel to the bedding plane.Pyrite-rich layer, mainly containing intercrystalline pores,shows a strong preferred orientation parallel to the bedding plane. OM-rich layer, mainly containing OM pores, seems to be discontinuous. In addition, intercrystalline pores are enriched in some layers, while OM pores are distributed irregularly in matrix layers. This vertical heterogeneity of pore microscopic structures in LMX shale is of great importance to understand its petrophysical and chemical properties.展开更多
Metal–organic frameworks(MOFs) are of great interest as potential electrochemically active materials.However, few studies have been conducted into understanding whether control of the shape and components of MOFs can...Metal–organic frameworks(MOFs) are of great interest as potential electrochemically active materials.However, few studies have been conducted into understanding whether control of the shape and components of MOFs can optimize their electrochemical performances due to the rational realization of their shapes. Component control of MOFs remains a significant challenge. Herein, we demonstrate a solvothermal method to realize nanostructure engineering of 2D nanoflake MOFs. The hollow structures withNi/Co-and Ni-MOF(denoted as Ni/Co-MOF nanoflakes and Ni-MOF nanoflakes) were assembled for their electrochemical performance optimizations in supercapacitors and in the oxygen reduction reaction(ORR). As a result, the Ni/CoMOF nanoflakes exhibited remarkably enhanced performance with a specific capacitance of 530.4 F g^(-1)at 0.5 A g^(-1)in1 M LiO H aqueous solution, much higher than that of NiMOF(306.8 F g^(-1)) and ZIF-67(168.3 F g^(-1)), a good rate capability, and a robust cycling performance with no capacity fading after 2000 cycles. Ni/Co-MOF nanoflakes also showed improved electrocatalytic performance for the ORR compared to Ni-MOF and ZIF-67. The present work highlights the significant role of tuning 2D nanoflake ensembles of Ni/Co-MOF in accelerating electron and charge transportation for optimizing energy storage and conversion devices.展开更多
A molecular dynamics simulation study has been performed for the microstructure evolution in a liquid metal Ni system during crystallization process at two cooling rates by adopting the embedded atom method （EAM） mo...A molecular dynamics simulation study has been performed for the microstructure evolution in a liquid metal Ni system during crystallization process at two cooling rates by adopting the embedded atom method （EAM） model potential. The bond-type index method of Honeycutt-Andersen （HA） and a new cluster-type index method （CTIM-2） have been used to detect and analyse the microstructures in this system. It is demonstrated that the cooling rate plays a critical role in the microstructure evolution： below the crystallization temperature Tc, the effects of cooling rate are very remarkable and can be fully displayed. At different cooling rates of 2.0 × 10^13 K·s^-1 and 1.0 × 10^12 K·s^-1, two different kinds of crystal structures are obtained in the system. The first one is the coexistence of the hcp （expressed by （12 0 0 0 6 6） in CTIM-2） and the fcc （12 0 0 0 12 0） basic clusters consisting of 1421 and 1422 bond-types, and the hcp basic cluster becomes the dominant one with decreasing temperature, the second one is mainly the fcc （12 0 0 0 12 0） basic clusters consisting of 1421 bond-type, and their crystallization temperatures Tc would be 1073 and 1173 K, respectively.展开更多
The strip-casting technique plays an important role in fabricating high coercivity sintered magnet. In this paper, we investigate the phase constitution and the microstructure of rapidly solidified Ce-Fe-B alloy fabri...The strip-casting technique plays an important role in fabricating high coercivity sintered magnet. In this paper, we investigate the phase constitution and the microstructure of rapidly solidified Ce-Fe-B alloy fabricated by strip-casting. We find that the Ce2FelgB phase coexists with Fe, Fe2B, and CeFe2 phases in the Ce-Fe-B strips. The eutectic stucture consisting of Fe and Fe2B is encased in Ce2Fe14B grains, which is blocked by the CeFe2 grains at triple junctions, indicating that the microstructure of Ce-Fe-B strip is characteristic of a peritectic solidification. Thermal analysis indicates that the large supercooling of Ce2Fe14B results in the residual Fe and Fe2B. The microstructural optimization in Ce-Fe-B strips without Fe and Fe2B could be achieved by a heat treatment of 1000 ℃.展开更多
In order to investigate the characteristics of re-oxidation of residual coal in goafs in close coal seam mining,scanning electron microscope and infrared spectrometer are used to study the changes of coal microstructu...In order to investigate the characteristics of re-oxidation of residual coal in goafs in close coal seam mining,scanning electron microscope and infrared spectrometer are used to study the changes of coal microstructure and chemical reaction of functional groups of eight coal samples at different ranks.Result shows that after initial oxidation,the surface morphology of pore are different,and the porosity of coal is increased and the oxygen adsorption capacity of coal is improved.The change of coal molecular structure and presence of a large amount of active oxygen-containing functional groups lead to increasing tendency of coal to further oxidation.In addition,the higher lever of the initial oxidation is,the easier the re-oxidation occurs.展开更多
During the plasma spheroidization process powders undergo different changes in their microstructures and crystal phases. In this paper, simple calculation of heat transfer between the plasma and a suspended particle w...During the plasma spheroidization process powders undergo different changes in their microstructures and crystal phases. In this paper, simple calculation of heat transfer between the plasma and a suspended particle was performed based on three hypotheses for the purpose of guiding experiments. Experimental investigation of the crystal phases and microstructural changes during the plasma processing was made using silica, alumina and nickel powders as starting materials. It has been revealed from the experimental results that these materials undergo different changes in crystal phases and microstructures, and these changes are essentially determined by the structures, properties and aggregate states of the starting materials.展开更多
基金Project supported by the Natural Science Foundation of Jilin Province,China(Grant No.YDZJ202201ZYTS319)the Fund from Sinoma Institute of Materials Research(Guangzhou)Co.,Ltd.(SIMR)for assisting with the TEM characterization。
文摘The microstructure and magnetic properties of Fe_(40)Co_(40)Zr_(9)B_(10)Ge_(1)(Mo-free)and Fe_(40)Co_(40)Zr_(5)Mo_(4)B_(10)Ge_(1)(Mocontaining)nanocrystalline alloys,prepared using an amorphous crystallization method,were investigated.Mo addition affects the crystallization of the Fe_(40)Co_(40)Zr_(9)B_(10)Ge_(1) amorphous alloy and decreases the grain size of theα-Fe(Co)phase below 650℃.For the Mo-free alloy annealed at 600℃ and the Mo-containing alloy annealed at 575℃,with a singleα-Fe(Co)crystallization phase and approximately similar crystallization volume fractions,the Mo-containing alloy showed smaller,more regularly shaped grains and a significantly narrower grain-size distribution than the Mo-free alloy.The Fe and Co contents in the nanograins of the two alloys also differed.For the Mo-free alloy,a higher concentration of Co distributed in the residual amorphous matrix.For the Mo-containing alloy,a higher concentration Co dissolved in the nanograins.The specific saturation magnetization and coercivity of the Mo-free alloy were 1.05-and 1.59-times higher than those of the Mo-containing alloy,respectively.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.52074315&U19B6003)。
文摘The difference in microstructure leads to the diversity of shale mechanical properties and bedding fractures distribution patterns.In this paper,the microstructure and mechanical properties of Longmaxi marine shale and Qingshankou continental shale were studied by X-ray diffractometer(XRD),field emission scanning electron microscope(FE-SEM)with mineral analysis system,and nanoindentation.Additionally,the typical bedding layers area was properly stratified using Focused Ion Beam(FIB),and the effects of microstructure and mechanical properties on the distribution patterns of bedding fractures were analyzed.The results show that the Longmaxi marine shale sample contains more clay mineral grains,while the Qingshankou continental shale sample contains more hard brittle mineral grains such as feldspar.For Longmaxi marine shale sample,hard brittle minerals with grain sizes larger than 20μm is18.24%and those with grain sizes smaller than 20μm is 16.22%.For Qingshankou continental shale sample,hard brittle minerals with grain sizes larger than 20μm is 40.7%and those with grain sizes smaller than 20μm is 11.82%.In comparison to the Qingshankou continental shale sample,the Longmaxi marine shale sample has a lower modulus,hardness,and heterogeneity.Laminated shales are formed by alternating coarse-grained and fine-grained layers during deposition.The average single-layer thickness of Longmaxi marine shale sample is greater than Qingshankou continental shale sample.The two types of shale have similar bedding fractures distribution patterns and fractures tend to occur in the transition zone from coarse-grained to fine-grained deposition.The orientation of the fracture is usually parallel to the bedding plane and detour occurs in the presence of hard brittle grains.The fracture distribution density of the Longmaxi marine shale sample is lower than that of the Qingshankou continental shale sample due to the strong heterogeneity of the Qingshankou continental shale.The current research provides guidelines for the effective development of shale reservoirs in various sedimentary environments.
基金Project supported by the Anhui Provincial Natural Science Foundation(Grant No.2208085QE121)the Key Research&Development Plan of Anhui Province(Grant No.2022a05020016)+1 种基金the University Natural Science Research Project of Anhui Province(Grant No.2023AH051084)the National Natural Science Foundation of China(Grant No.52071078)。
文摘Compared to the commercial soft-magnetic alloys,the high saturation magnetic flux density(Bs)and low coercivity(Hc)of post-developed novel nanocrystalline alloys tend to realize the miniaturization and lightweight of electronic products,thus attracting great attention.In this work,we designed a new FeNiBCuSi formulation with a novel atomic ratio,and the microstructure evolution and magnetic softness were investigated.Microstructure analysis revealed that the amount of Si prompted the differential chemical fluctuations of Cu element,favoring the different nucleation and growth processes ofα-Fe nanocrystals.Furthermore,microstructural defects associated with chemical heterogeneities were unveiled using the Maxwell-Voigt model with two Kelvin units and one Maxwell unit based on creeping analysis by nanoindentation.The defect,with a long relaxation time in relaxation spectra,was more likely to induce the formation of crystal nuclei that ultimately evolved into theα-Fe nanocrystals.As a result,Fe_(84)Ni_(2)B_(12.5)Cu_(1)Si_(0.5)alloy with refined uniform nanocrystalline microstructure exhibited excellent magnetic softness,including a high B_(s)of 1.79 T and very low H_(c)of 2.8 A/m.Our finding offers new insight into the influence of activated defects associated with chemical heterogeneities on the microstructures of nanocrystalline alloy with excellent magnetic softness.
基金National Key Laboratory of Science and Technology on Materials under Shock and Impact(Grant No.WDZC2022-4)to provide fund for conducting experiments。
文摘A reasonable heat treatment process for TC4 ELI titanium alloy is crucial to tune microstructures to improve its explosion resistance.However,there is limited investigation on tuning microstructures of TC4 ELI to improve explosion resistance.Moreover,the current challenge is quantifying microstructural changes'effects on explosion resistance and incorporating microstructural changes into finite element models.This work aims to tune microstructures to improve explosion resistance and elucidate their anti-explosion mechanism,and find a suitable method to incorporate microstructural changes into finite element models.In this work,we systematically study the deformation and failure characteristics of TC4 ELI plates with varying microstructures using an air explosion test and LS-DYNA finite element modeling.The Johnson-Cook(JC)constitutive parameters are used to quantify the effects of microstructural changes on explosion resistance and incorporate microstructural changes into finite element models.Because of the heat treatment,one plate has equiaxed microstructure and the other has bimodal microstructure.The convex of the plate after the explosion has a quadratic relationship with the charge mass,and the simulation results demonstrate high reliability,with the error less than 17.5%.Therefore,it is feasible to obtain corresponding JC constitutive parameters based on the differences in microstructures and mechanical properties and characterize the effects of microstructural changes on explosion resistance.The bimodal target exhibits excellent deformation resistance.The response of bimodal microstructure to the shock wave may be more intense under explosive loading.The well-coordinated structure of the bimodal target enhances its resistance to deformation.
基金financially supported by Ministry of Science and Higher Education of the Russian Federation(Grant No.FENU-2023-0013)。
文摘The high entropy alloys(HEAs)are the newly developed high-performance materials that have gained significant importance in defence,nuclear and aerospace sector due to their superior mechanical properties,heat resistance,high temperature strength and corrosion resistance.These alloys are manufactured by the equal mixing or larger proportions of five or more alloying elements.HEAs exhibit superior mechanical performance compared to traditional engineering alloys because of the extensive alloying composition and higher entropy of mixing.Solid state welding(SSW)techniques such as friction stir welding(FSW),rotary friction welding(RFW),diffusion bonding(DB)and explosive welding(EW)have been efficiently deployed for improving the microstructural integrity and mechanical properties of welded HEA joints.The HEA interlayers revealed greater potential in supressing the formation of deleterious intermetallic phases and maximizing the mechanical properties of HEAs joints.The similar and dissimilar joining of HEAs has been manifested to be viable for HEA systems which further expands their industrial applications.Thus,the main objective of this review paper is to present a critical review of current state of research,challenges and opportunities and main directions in SSW of HEAs mainly CoCrFeNiMn and Al_xCoCrFeNi alloys.The state of the art of problems,progress and future outlook in SSW of HEAs are critically reviewed by considering the formation of phases,microstructural evolution and mechanical properties of HEAs joints.
基金supported by National Natural Science Foundation of China (52070194,52073309)Natural Science Foundation of Hunan Province (2022JJ20069)。
文摘Generally,layered Ni-rich cathode materials exhibit the morphology of polycrystalline secondary sphere composed of numerous primary particles.While the arrangement of primary particles plays a very important role in the properties of Ni-rich cathodes.The disordered particle arrangement is harmful to the cyclic performance and structural stability,yet the fundamental understanding of disordered structure on the structural degradation behavior is unclarified.Herein,we have designed three kinds of LiNi_(0.83)Co_(0.06)Mn_(0.11)O_(2) cathode materials with different primary particle orientations by regulating the precursor coprecipitation process.Combining finite element simulation and in-situ characterization,the Li^(+)transport and structure evolution behaviors of different materials are unraveled.Specifically,the smooth Li^(+)diffusion minimizes the reaction heterogeneity,homogenizes the phase transition within grains,and mitigates the anisotropic microstructural change,thereby modulating the crack evolution behavior.Meanwhile,the optimized structure evolution ensures radial tight junctions of the primary particles,enabling enhanced Li^(+)diffusion during dynamic processes.Closed-loop bidirectional enhancement mechanism becomes critical for grain orientation regulation to stabilize the cyclic performance.This precursor engineering with particle orientation regulation provides the useful guidance for the structural design and feature enhancement of Ni-rich layered cathodes.
基金supported by the Na⁃tional Natural Science Foundation of China(Nos.12462006,12062016)the high-performance computing services of⁃fered by the Information Center of Nanchang Hangkong Uni⁃versity.
文摘Molecular dynamics(MD)simulations are employed to delve into the multifaceted effects of TiB_(2) nanoparticles on the intricate grain refinement mechanism,microstructural evolution,and tensile performance of Inconel 718 superalloys during the rapid directional solidification.Specifically,the study focuses on elucidating the role of TiB2 nanoparticles in augmenting the nucleation rate during the rapid directional solidification process of Ni_(60)Cr_(21)Fe_(19) alloy system.Furthermore,subsequent tensile simulations are conducted to comprehensively evaluate the anisotropic behavior of tensile properties within the solidified microstructures.The MD results reveal that the incorporation of TiB₂nanoparticles during the rapid directional solidification of the Ni_(60)Cr_(21)Fe_(19) significantly enhances the average nucleation rate,escalating it from 1.27×10^(34)m^(-3)·s^(-1)to 2.55×10^(34)m^(-3)·s^(-1).Notably,within the face centered cube(FCC)structure,Ni atoms exhibit pronounced compositional segregation,and the solidified alloy maintains an exceptionally high dislocation density reaching up to 10^(16)m^(-2).Crucially,the rapid directional solidification process imparts a distinct microstructural anisotropy,leading to a notable disparity in tensile strength.Specifically,the tensile strength along the solidification direction is markedly superior to that perpendicular to it.This disparity arises from different deformation mechanisms under varying loading orientations.Tensile stress perpendicular to the solidification direction encourages the formation of smooth and organized mechanical twins.These twins act as slip planes,enhancing dislocation mobility and thereby improving stress relaxation and dispersion.Moreover,the results underscore the profound strengthening effect of TiB_(2) nanoparticles,particularly in enhancing the tensile strength along the rapid directional solidification direction.
基金Project supported by the National Natural Science Foundation of China(Grant No.62164005).
文摘Combining theory and computation,we explore the Goos–H¨anchen(GH)effect for electrons in a single-layered semiconductor microstructure(SLSM)modulated by Dresselhaus spin–orbit coupling(SOC).GH displacement depends on electron spins thanks to Dresselhaus SOC,therefore electron spins can be separated from the space domain and spinpolarized electrons in semiconductors can be realized.Both the magnitude and sign of the spin polarization ratio change with the electron energy,in-plane wave vector,strain engineering and semiconductor layer thickness.The spin polarization ratio approaches a maximum at resonance;however,no electron-spin polarization occurs in the SLSM for a zero in-plane wave vector.More importantly,the spin polarization ratio can be manipulated by strain engineering or semiconductor layer thickness,giving rise to a controllable spatial electron-spin splitter in the field of semiconductor spintronics.
基金supported by the project funded by China Postdoctoral Science Foundation(grant number 2020M671111).
文摘The microstructural evolution and relaxation strengthening of nano-grained Ni annealed at a temperature range of 493–553 K were studied by in situ X-ray diffraction technique,transmission electron microscopy,and microhardness evaluation.Upon low-temperature annealing,the rather limited variations of anisotropic grain size and root-mean-square strain,conforming to an exponential relaxation model,yield a consistent activation energy of approximately 0.5 eV,which corresponds to the localized,rapid diffusion of excess vacancies on nonequilibrium surfaces/interfaces and/or defective lattice configurations.Microstructure examinations confirm the grain boundary ordering and excess defect reduction.The relaxation-induced strength enhancement can be attributed to the linear strengthening in the regime of small elastic lattice strains.This study provides an in-depth understanding of low-temperature nanostructural relaxation and its relation to strengthening.
基金the Natural Science Foundation of Jiangsu Province(BK2006723)the China Postdoc-toral Science Foundation(20060400282)~~
文摘The effects of rare earth Lanthanum on the microstructure, the physical property and the microhardness of Ag-Cu-Ti solder alloy are studied. Experimental results indicate that the addition of Lanthanum can evidently improve the wettability and the microhardness of Ag-Cu-Ti solder alloy. Analysis results show that the increase in microhardness is related to the refining and uniform distribution of the intermetallic compounds. Proper content of Lanthanum added in Ag-Cu-Ti alloy solder can be controlled below 0.5% in mass percent.
基金Supported by the National Natural Science Foundation of China(50475040)the Aeronautical Science Foundation of China(2005ZH52060)the Natural Science Foundation of Jiangsu Province(BK2006723)~~
文摘The samples of brazed diamond grits with NiCr brazing alloy are prepared in vacuum and argon gas. The microstructures are analyzed with scanning electron microscope （SEM）, energy dispersive X-ray spectroscopy （EDS） and X-ray diffraction（XRD）. The effects of brazing atmospheres on the as-brazed NiCr brazing alloy composite structures and interracial microstructure are studied between diamond grits and brazing alloy. Results show that： （1） There are different composite structures of as-brazed NiCr brazing alloy under different oxygen partial pressures in vacuum and argon gas. B203 exists on the surface of the brazed samples under argon gas furnace brazing. It indicates that oxygen plays an important role in the resultants of as-brazed NiCr brazing alloy during the brazing process. （2） There are different interfacial microstructures in different brazing atmospheres, but the main reaction product is chromium carbides. The chromium carbides in argon gas furnace brazing grow in a disordered form, but those in vacuum furnace brazing grow radiated. And the scale of grains in argon gas is smaller than those in vacuum.
文摘The Brownian dynamics （BD） simulation of a dilute surfactant solution is conducted in a steady shear flow. The rodlike micelle is assumed as a rigid rod composed of lined-up beads. A novel intercluster potential model is introduced for describing the interactions between, micelles. In the model, the Lennard-Jones and the soft-sphere potentials are used as inter-bead potentials for end-end and interior-interior beads, respectively. The micelles are combined at their ends to form a network structure at lower shear rates and are disconnected to become more and more parallel to the shear flow direction with increasing shear rate. The change of micellar microstructures with the variation of the shear rate results in shear thinning characteristics of the computed shear viscosities and first normal stress difference coefficients. The effects of surfactant solution concentration on the micellar structures and rheological properties are also investigated. Results show that the shear viscosities and the first normal stress difference coefficients increase with increasing the viscosity of the surfactant solution.
文摘The composition and sequence distribution of monomeric units in polyester polyether multiblock copolymer were studied by pyrolysis? gas chromatography (PGC) and pyrolysis gas chromatography/mass spectrometry (PGC/MS). PGC was applied to study the F t curve of the multiblock copolymer and PGC/MS was used to separate and identify the pyrolyzates. DTA experiment was used to study the decomposition temperature. The results show that the beginning point of elastomer’s decomposition was about 300?℃ and the decomposition temperature of most of the sample was 550?℃. Many pyrolyzates were produced because of the breaking of weak bonds in the sample. The possible microstructure was verified and the pyrolysis pathway of the copolymer was investigated.
基金provided by the National Natural Science Foundation of China (No. U1261207)
文摘This paper is to study the influence of composition, microstructure and pore characteristics on the rock mechanical properties. Five kinds of sandstone compositions were analyzed by using X-ray diffraction instrument. And the microstructure was observed by using scanning electron microscope. Then the pore distribution characteristic was investigated by using the low field nuclear magnetic resonance equipment. Finally, the uniaxial compression test was carried out to investigate the mechanical characteristics by using RMT150C mechanics experimental system and the uniaxial compressive strength, Poisson's ratio and elastic modulus were obtained. Compared to the analysis of the composition, structure and pore distribution and mechanical properties of the five kinds of sandstones, the relationship among composition,structure, pore distribution and mechanical properties was obtained. The results show that the composition, microstructure, pore distribution and mechanical properties of sandstone are closely related.With the decrease of feldspar and quartz particles, the compressive strength and elastic modulus increase, while the porosity decreases.
基金supported by the Strategic Priority Research Program of the Chinese Academy of Sciences(No.XDB1002010)the Major Program for the Fundamental Research of Shanghai Committee of Science and Technology(No.12JC1410400)the National Natural Science Foundation of China for Distinguished Young Scholars(No.41325016)
文摘Microstructure of shale formation is the key to understanding its petrophysical and chemical properties.Optical microscopy, scanning electron microscopy and micro-computed tomography(μ-CT) have been combined for characterization of microstructure of Longmaxi(LMX)shale from Shizhu area, Sichan Basin. The results indicate that laminated LMX shale consists of mineral matrix-rich layers and organic matter(OM)-rich layers at micrometer scale in two and three dimensions. Mineral matrix layers,mainly consisting of interparticle pores and intraplatelet pores, are approximately parallel to the bedding plane.Pyrite-rich layer, mainly containing intercrystalline pores,shows a strong preferred orientation parallel to the bedding plane. OM-rich layer, mainly containing OM pores, seems to be discontinuous. In addition, intercrystalline pores are enriched in some layers, while OM pores are distributed irregularly in matrix layers. This vertical heterogeneity of pore microscopic structures in LMX shale is of great importance to understand its petrophysical and chemical properties.
基金supported by the National Natural Science Foundation of China (Nos. 21571157, U1604123, and 51473149)Outstanding Young Talent Research Fund of Zhengzhou University (1521320001)+1 种基金the Open Project Foundation of Key Laboratory of Advanced Energy Materials Chemistry (Ministry of Education) (2017–29),Nankai UniversityOpen Project Foundation of Key Laboratory of Inorganic Synthesis and Preparation of Jilin University
文摘Metal–organic frameworks(MOFs) are of great interest as potential electrochemically active materials.However, few studies have been conducted into understanding whether control of the shape and components of MOFs can optimize their electrochemical performances due to the rational realization of their shapes. Component control of MOFs remains a significant challenge. Herein, we demonstrate a solvothermal method to realize nanostructure engineering of 2D nanoflake MOFs. The hollow structures withNi/Co-and Ni-MOF(denoted as Ni/Co-MOF nanoflakes and Ni-MOF nanoflakes) were assembled for their electrochemical performance optimizations in supercapacitors and in the oxygen reduction reaction(ORR). As a result, the Ni/CoMOF nanoflakes exhibited remarkably enhanced performance with a specific capacitance of 530.4 F g^(-1)at 0.5 A g^(-1)in1 M LiO H aqueous solution, much higher than that of NiMOF(306.8 F g^(-1)) and ZIF-67(168.3 F g^(-1)), a good rate capability, and a robust cycling performance with no capacity fading after 2000 cycles. Ni/Co-MOF nanoflakes also showed improved electrocatalytic performance for the ORR compared to Ni-MOF and ZIF-67. The present work highlights the significant role of tuning 2D nanoflake ensembles of Ni/Co-MOF in accelerating electron and charge transportation for optimizing energy storage and conversion devices.
基金Project supported by the National Natural Science Foundation of China （Grant Nos 50271026 and 50571037）.
文摘A molecular dynamics simulation study has been performed for the microstructure evolution in a liquid metal Ni system during crystallization process at two cooling rates by adopting the embedded atom method （EAM） model potential. The bond-type index method of Honeycutt-Andersen （HA） and a new cluster-type index method （CTIM-2） have been used to detect and analyse the microstructures in this system. It is demonstrated that the cooling rate plays a critical role in the microstructure evolution： below the crystallization temperature Tc, the effects of cooling rate are very remarkable and can be fully displayed. At different cooling rates of 2.0 × 10^13 K·s^-1 and 1.0 × 10^12 K·s^-1, two different kinds of crystal structures are obtained in the system. The first one is the coexistence of the hcp （expressed by （12 0 0 0 6 6） in CTIM-2） and the fcc （12 0 0 0 12 0） basic clusters consisting of 1421 and 1422 bond-types, and the hcp basic cluster becomes the dominant one with decreasing temperature, the second one is mainly the fcc （12 0 0 0 12 0） basic clusters consisting of 1421 bond-type, and their crystallization temperatures Tc would be 1073 and 1173 K, respectively.
基金Project supported by the National High Technology Research and Development Program of China(Grant No.2011AA03A401)
文摘The strip-casting technique plays an important role in fabricating high coercivity sintered magnet. In this paper, we investigate the phase constitution and the microstructure of rapidly solidified Ce-Fe-B alloy fabricated by strip-casting. We find that the Ce2FelgB phase coexists with Fe, Fe2B, and CeFe2 phases in the Ce-Fe-B strips. The eutectic stucture consisting of Fe and Fe2B is encased in Ce2Fe14B grains, which is blocked by the CeFe2 grains at triple junctions, indicating that the microstructure of Ce-Fe-B strip is characteristic of a peritectic solidification. Thermal analysis indicates that the large supercooling of Ce2Fe14B results in the residual Fe and Fe2B. The microstructural optimization in Ce-Fe-B strips without Fe and Fe2B could be achieved by a heat treatment of 1000 ℃.
基金the National Key Foundation for Exploring Scientific Instruments of China(No.2012YQ24012705)the National Natural Science Foundation of China(No.51174113)+2 种基金the special fund for Scientific Research Institutes of China(Nos.2013EG122192 and 2014EG122293)CCTEG Innovation Foundation of China(No. 2014MS030)Shenhua Innovation Foundation of China(No. SHGF-13-07)
文摘In order to investigate the characteristics of re-oxidation of residual coal in goafs in close coal seam mining,scanning electron microscope and infrared spectrometer are used to study the changes of coal microstructure and chemical reaction of functional groups of eight coal samples at different ranks.Result shows that after initial oxidation,the surface morphology of pore are different,and the porosity of coal is increased and the oxygen adsorption capacity of coal is improved.The change of coal molecular structure and presence of a large amount of active oxygen-containing functional groups lead to increasing tendency of coal to further oxidation.In addition,the higher lever of the initial oxidation is,the easier the re-oxidation occurs.
基金supported by National Natural Science Foundation of China (No.50574083)
文摘During the plasma spheroidization process powders undergo different changes in their microstructures and crystal phases. In this paper, simple calculation of heat transfer between the plasma and a suspended particle was performed based on three hypotheses for the purpose of guiding experiments. Experimental investigation of the crystal phases and microstructural changes during the plasma processing was made using silica, alumina and nickel powders as starting materials. It has been revealed from the experimental results that these materials undergo different changes in crystal phases and microstructures, and these changes are essentially determined by the structures, properties and aggregate states of the starting materials.
