Crop water stress index(CWSI)is widely used for efficient irrigation management.Precise canopy temperature(T_(c))measurement is necessary to derive a reliable CWSI.The objective of this research was to investigate the...Crop water stress index(CWSI)is widely used for efficient irrigation management.Precise canopy temperature(T_(c))measurement is necessary to derive a reliable CWSI.The objective of this research was to investigate the influences of atmospheric conditions,settled height,view angle of infrared thermography,and investigating time of temperature measuring on the performance of the CWSI.Three irrigation treatments were used to create different soil water conditions during the 2020-2021 and 2021-2022 winter wheat-growing seasons.The CWSI was calculated using the CWSI-E(an empirical approach)and CWSI-T(a theoretical approach)based on the T_(c).Weather conditions were recorded continuously throughout the experimental period.The results showed that atmospheric conditions influenced the estimation of the CWSI;when the vapor pressure deficit(VPD)was>2000 Pa,the estimated CWSI was related to soil water conditions.The height of the installed infrared thermograph influenced the T_(c)values,and the differences among the T_(c)values measured at height of 3,5,and 10 m was smaller in the afternoon than in the morning.However,the lens of the thermometer facing south recorded a higher T_(c)than those facing east or north,especially at a low height,indicating that the direction of the thermometer had a significant influence on T_(c).There was a large variation in CWSI derived at different times of the day,and the midday measurements(12:00-15:00)were the most reliable for estimating CWSI.Negative linear relationships were found between the transpiration rate and CWSI-E(R^(2)of 0.3646-0.5725)and CWSI-T(R^(2)of 0.5407-0.7213).The relations between fraction of available soil water(FASW)with CWSI-T was higher than that with CWSI-E,indicating CWSI-T was more accurate for predicting crop water status.In addition,The R^(2)between CWSI-T and FASW at 14:00 was higher than that at other times,indicating that 14:00 was the optimal time for using the CWSI for crop water status monitoring.Relative higher yield of winter wheat was obtained with average seasonal values of CWSI-E and CWSI-T around 0.23 and 0.25-0.26,respectively.The CWSI-E values were more easily influenced by meteorological factors and the timing of the measurements,and using the theoretical approach to derive the CWSI was recommended for precise irrigation water management.展开更多
Two dynamic grey models DGM (1, 1) for the verification cycle and the lifecycle of measuring instrument based on time sequence and frequency sequence were set up, according to the statistical feature of examination da...Two dynamic grey models DGM (1, 1) for the verification cycle and the lifecycle of measuring instrument based on time sequence and frequency sequence were set up, according to the statistical feature of examination data and weighting method. By a specific case, i.e. vernier caliper, it is proved that the fit precision and forecast precision of the models are much higher, the cycles are obviously different under different working conditions, and the forecast result of the frequency sequence model is better than that of the time sequence model. Combining dynamic grey model and auto-manufacturing case the controlling and information subsystems of verification cycle and the lifecycle based on information integration, multi-sensor controlling and management controlling were given. The models can be used in production process to help enterprise reduce error, cost and flaw.展开更多
The principle and method of both radar target imaging and velocity measurement simultaneously based on step frequency waveforms is presented. Velocity compensation is necessary in order to obtain the good High resolut...The principle and method of both radar target imaging and velocity measurement simultaneously based on step frequency waveforms is presented. Velocity compensation is necessary in order to obtain the good High resolution range profile since this waveform is greatly sensitive to the Doppler shift. The velocity measurement performance of the four styles is analyzed with two pulse trains consisted of positive and negative step frequency waveforms. The velocity of targets can be estimated first coarsely by using the pulse trains with positive-positive step frequency combination, and then fine by positive-negative combination. Simulation results indicate that the method can accomplish the accurate estimation of the velocity with efficient computation and good anti-noise performance and obtain the good HRRP simultaneously.展开更多
Based on the characters of plant potentials, it introduced the construction and technology in developing the measuring system of plant electrical potentials, the input impedance of the amplifier must be enough high(= ...Based on the characters of plant potentials, it introduced the construction and technology in developing the measuring system of plant electrical potentials, the input impedance of the amplifier must be enough high(= 1010～ 1012Ω) in order to measuring the plant weak signals and ensuring high common mode rejection ratio (CMRR). And wavelet transform was applied in denoising based on cross-validation (CV)threshold value. the experiment showed that this system could effectively detect the change of plant potentials,four-week old cucumber was stimulated by heat wounding, the variation potential (VP) and action potential(AP) would be evoked, the AP's varying amplitude can reach 40mV; the AP changed very fast, its duration time is about 0.01～0.02s and its amplitude often change from 15μV～5mV.展开更多
Thyristor valve is one of the key equipments for ultra high voltage direct current(UHVDC) power transmission projects.Before being installed on site,they need to be tested in a laboratory in order to verify their oper...Thyristor valve is one of the key equipments for ultra high voltage direct current(UHVDC) power transmission projects.Before being installed on site,they need to be tested in a laboratory in order to verify their operational performance to satisfy the technical specification of project related.Test facilities for operational tests of thyristor valves are supposed to enable to undertake more severe electrical stresses than those being applied in the thyristor valves under test(test objects).On the other hand,the stresses applied into the test objects are neither higher nor lower than specified by the specification,because inappropriate stresses applied would result in incorrect evaluation of performance on the test objects,more seriously,would cuase the damage of test objects with expensive cost losing.Generally,the process of operational tests is complicated and performed in a complex synthetic test circuit(hereafter as STC),where there are a lot of sensors used for measuring,monitoring and protection on line to ensure that the test circuit functions in good condition.Therefore,the measuring systems embedded play a core role in STC,acting like "eyes".Based on the first project of building up a STC in China,experience of planning measuring systems is summarized so as to be referenced by related engineers.展开更多
Comparison of thermal performance between a green roof room and a bare roof room was presented during the cooling period in Shanghai. The results show that the electricity can be saved about 0.08 kW·h/(d·m2)...Comparison of thermal performance between a green roof room and a bare roof room was presented during the cooling period in Shanghai. The results show that the electricity can be saved about 0.08 kW·h/(d·m2),and the heat flux can be reduced by about 70%; the inner surface temperature variation is about 1.0 ℃ comparing with the indoor temperature when using the green roof,and the extra equivalent heat resistance is 1.0 m2·K/W.展开更多
The principles for measuring characteristic grain sizes of materials, such as fully-dense single phase materials, porous materials and materials with isolated second phase particles, are developed on the basis of its ...The principles for measuring characteristic grain sizes of materials, such as fully-dense single phase materials, porous materials and materials with isolated second phase particles, are developed on the basis of its definition associated closely with the surface area per unit volume, Sv, of grain. The focus of the measuring principles of the characteristic grain size is put on determining Sv of grains. Unlike the measurement of average grain size commonly used, G, correcting factors such as grain shape and grain size distribution factors, will not be applied to the determination of the characteristic grain size, Gc, due to its unique geometric meaning and the measure precision of Sv being guaranteed by quantitative stereological technique and gas adsorption method. The measurement of Gc can be directly carried out on the polished and etched cross section of materials, similar to the measuremernt of the average grain size using the Heyn intercept method.展开更多
Based on the computer integrated and flexible laser p rocessing system, we developed an intelligent measuring sub-system. A novel mod el has been built to compensate the deviations of the main frame-structure, and a l...Based on the computer integrated and flexible laser p rocessing system, we developed an intelligent measuring sub-system. A novel mod el has been built to compensate the deviations of the main frame-structure, and a laser tracker system is applied to calibrate the accuracy of the system. Anal yzing the characteristics of all kind surfaces of automobile outer penal moulds and dies, the surface and border to be measured and processed are classified int o four types. A 2-D adaptive measuring method based on Bzier curve and a 3 -D adaptive measuring method based on Spline curve are developed for different types of surface. During the data processing, a 3-D probe compensation method i s described in details. The control software of the sub-measuring system is des cribed. Some measuring experiments are carried out to testify the methods.展开更多
The work of quantitative studying the effect of technological progress on economic growth, being of great complexity and far-reaching significance, has become a quite popular research topic in the world. In recent yea...The work of quantitative studying the effect of technological progress on economic growth, being of great complexity and far-reaching significance, has become a quite popular research topic in the world. In recent years there are a large number of scientists who are engaged in this research both at home and abroad.展开更多
The revolution of information technology within the p ast twenty years has dramatically changed the picture of our economy. Numerous n ew possibilities of communication have let competition advantages for many compa n...The revolution of information technology within the p ast twenty years has dramatically changed the picture of our economy. Numerous n ew possibilities of communication have let competition advantages for many compa nies and even advantageous macroeconomic consequences emerge on national and international level. Through newly developed information technologies the knowl edge base of market participants improves with a concurrent reduction of the inf ormation obtaining costs. As a result considerable competition advantages develo p for those companies acting in E-commerce networks. These advantages of the la test development lead to macroeconomic effects on national level, if the effecti veness and efficiency increasing possibilities are used more strongly than in ot her countries. Positive international effects arise since the allocation effic iency is increased through intensified competition between different market pa rticipants in various countries. This in turn leads to an increase in wo rldwide prosperity. This causal chain however is not yet realistic to the whole extent, as such an i ncreased transparency of information is not necessarily accepted by all market p articipants. Otherwise a considerable productivity increase would already have o ccurred in industrial countries. Overall the question arises, whether the change s in the competition situation make single enterprises technically more effectiv e, concurrently however deteriorate the efficiency of the entire market through informational asymmetries. To answer these and further questions and to measure the effectiveness and effic iency of various E-commerce networks an interdisciplinary analysis platform is to be developed. With the help of this platform, it should be possible to examin e single and macroeconomic questions, reveal temporal connections and to analyse aspects of business management and national economy, information management, em ployment politics and finance politics. For this, various part-models for the i ndividual knowledge disciplines have to be generated and brought together in the platform. This platform allows various users to make the right decisions (effec tiveness) with the help of the developed models and to competently estimate the effects (efficiency). Currently models of the individual knowledge disciplines (business management, e conomics, computer science) are being developed within the research project EEE. con. This project deals with the question of Supply Chain Management (SCM), E-P rocurement, with the implementation of inter-organisational information systems , as well as various market, competition and organisation models. The department of economics and computer science from Prof. Dr.-Ing. habil. W. Dangelmaier particularly deals with the development of an agent controlled SCM- communication model which is part of the E-commerce analysis platform. Both are described in this paper. Furthermore, a unified modelling language in order to allow a prototypic implementation of the analysis tool and to make the work with other project participants and external participants easier is decided upon wit hin this project.展开更多
Measuring the business-IT alignment(BITA)of an organization determines its alignment level,provides directions for further improvements,and consequently promotes the organizational performances.Due to the capabilities...Measuring the business-IT alignment(BITA)of an organization determines its alignment level,provides directions for further improvements,and consequently promotes the organizational performances.Due to the capabilities of enterprise architecture(EA)in interrelating different business/IT viewpoints and elements,the development of EA is superior to support BITA measurement.Extant BITA measurement literature is sparse when it concerns EA.The literature tends to explain how EA viewpoints or models correlate with BITA,without discussing where to collect and integrate EA data.To address this gap,this paper attempts to propose a specific BITA measurement process through associating a BITA maturity model with a famous EA framework:DoD Architectural Framework 2.0(DoDAF2.0).The BITA metrics in the maturity model are connected to the meta-models and models of DoDAF2.0.An illustrative ArchiSurance case is conducted to explain the measurement process.Systematically,this paper explores the process of BITA measurement from the viewpoint of EA,which helps to collect the measurement data in an organized way and analyzes the BITA level in the phase of architecture development.展开更多
The advancement of small satellites is promoting the development of distributed satellite systems,and for the latter,it is essential to coordinate the spatial and temporal relations between mutually visible satellites...The advancement of small satellites is promoting the development of distributed satellite systems,and for the latter,it is essential to coordinate the spatial and temporal relations between mutually visible satellites.By now,dual one-way ranging(DOWR)and two-way time transfer(TWTT)are generally integrated in the same software and hardware system to meet the limitations of small satellites in terms of size,weight and power(SWaP)consumption.However,studies show that pseudo-noise regenerative ranging(PNRR)performs better than DOWR if some advanced implementation technologies are employed.Besides,PNRR has no requirement on time synchronization.To apply PNRR to small satellites,and meanwhile,meet the demand for time difference measurement,we propose the round-way time difference measurement,which can be combined with PNRR to form a new integrated system without exceeding the limits of SWaP.The new integrated system can provide distributed small satellite systems with on-orbit high-accuracy and high-precision distance measurement and time difference measurement in real time.Experimental results show that the precision of ranging is about 1.94 cm,and that of time difference measurement is about 78.4 ps,at the signal to noise ratio of 80 dBHz.展开更多
A new non-invasive blood glucose measuring apparatus (NBGMA) made up of MSP430F149 SCM (single chip micyoco) was developed,which can measure blood glucose level (BGL) frequently,conveniently and painlessly. The hardwa...A new non-invasive blood glucose measuring apparatus (NBGMA) made up of MSP430F149 SCM (single chip micyoco) was developed,which can measure blood glucose level (BGL) frequently,conveniently and painlessly. The hardware and software of this apparatus were designed,and detecting algorithms based on conservation of energy method (COEM) were presented. According to the law of conservation of energy that the energy derived by human body equals energy consumed by metabolism,and the relationship between convection,evaporation,radiation and the BGL was established. The sensor module was designed. 20 healthy volunteers were involved in the clinical experiment. The BGL measured by an automatic biochemical analyzer (ABA) was set as the reference. Regression analysis was performed to compare the conservation of energy method with the biochemical method,using the 20 data points with blood glucose concentrations ranging from 680 to 1 100 mg/L. Reproducibility was measured for healthy fasting volunteers. The results show that the means of BGL detected by NBGMA and ANA are very close to each other,and the difference of standard deviation (SD) is 24.7 mg/L. The correlative coefficient is 0.807. The coefficient of variation (CV) is 4% at 921.6 mg/L. The resultant regression is evaluated by the Clarke error grid analysis (EGA) and all data points are included in the clinically acceptable regions (region A:100%,region B:0%). Accordingly,it is feasible to measure BGL with COEM.展开更多
By analyzing the effect of cross traffic (CT) enforced on packet delay, an improved path capacity measurement method, pcapminp algorithm, was proposed. With this method, path capacity was measured by filtering probe s...By analyzing the effect of cross traffic (CT) enforced on packet delay, an improved path capacity measurement method, pcapminp algorithm, was proposed. With this method, path capacity was measured by filtering probe samples based on measured minimum packet-pair delay. The measurability of minimum packet-pair delay was also analyzed by simulation. The results show that, when comparing with pathrate, if the CT load is light, both pcapminp and pathrate have similar accuracy; but in the case of heavy CT load, pcapminp is more accurate than Pathrate. When CT load reaches 90%, pcapminp algorithm has only 5% measurement error, which is 10% lower than that of pathrate algorithm. At any CT load levels, the probe cost of pcapminp algorithm is two magnitudes smaller than that of pathrate, and the measurement duration is one magnitude shorter than that of pathrate algorithm.展开更多
As an advanced device for observing atmospheric winds,the spaceborne Doppler Asymmetric Spatial Heterodyne(DASH)interferometer also encounters challenges associated with phase distortion,par-ticularly in limb sounding...As an advanced device for observing atmospheric winds,the spaceborne Doppler Asymmetric Spatial Heterodyne(DASH)interferometer also encounters challenges associated with phase distortion,par-ticularly in limb sounding scenarios.This paper discusses interferogram modeling and phase distortion cor-rection techniques for spaceborne DASH interferometers.The modeling of phase distortion interferograms with and without Doppler shift for limb observation was conducted,and the effectiveness of the analytical expression was verified through numerical simulation.The simulation results indicate that errors propagate layer by layer while using the onion-peeling inversion algorithm to handle phase-distorted interferograms.In contrast,the phase distortion correction algorithm can achieve effective correction.This phase correction method can be successfully applied to correct phase distortions in the interferograms of the spaceborne DASH interferometer,providing a feasible solution to enhance its measurement accuracy.展开更多
Risk management often plays an important role in decision making un-der uncertainty.In quantitative risk management,assessing and optimizing risk metrics requires eficient computing techniques and reliable theoretical...Risk management often plays an important role in decision making un-der uncertainty.In quantitative risk management,assessing and optimizing risk metrics requires eficient computing techniques and reliable theoretical guarantees.In this pa-per,we introduce several topics on quantitative risk management and review some of the recent studies and advancements on the topics.We consider several risk metrics and study decision models that involve the metrics,with a main focus on the related com-puting techniques and theoretical properties.We show that stochastic optimization,as a powerful tool,can be leveraged to effectively address these problems.展开更多
The concept of emissivity has been with the scientific and engineering world since Planck formulated his blackbody radiation law more than a century ago.Nevertheless,emissivity is an elusive concept even for ex⁃perts....The concept of emissivity has been with the scientific and engineering world since Planck formulated his blackbody radiation law more than a century ago.Nevertheless,emissivity is an elusive concept even for ex⁃perts.It is a vague and fuzzy concept for the wider community of engineers.The importance of remote sensing of temperature by measuring IR radiation has been recognized in a wide range of industrial,medical,and environ⁃mental uses.One of the major sources of errors in IR radiometry is the emissivity of the surface being measured.In real experiments,emissivity may be influenced by many factors:surface texture,spectral properties,oxida⁃tion,and aging of surfaces.While commercial blackbodies are prevalent,the much-needed grey bodies with a known emissivity,are unavailable.This study describes how to achieve a calibrated and stable emissivity with a blackbody,a perforated screen,and a reliable and linear novel IR thermal sensor,18 dubbed TMOS.The Digital TMOS is now a low-cost commercial product,it requires low power,and it has a small form factor.The method⁃ology is based on two-color measurements,with two different optical filters,with selected wavelengths conform⁃ing to the grey body definition of the use case under study.With a photochemically etched perforated screen,the effective emissivity of the screen is simply the hole density area of the surface area that emits according to the blackbody temperature radiation.The concept is illustrated with ray tracing simulations,which demonstrate the approach.Measured results are reported.展开更多
As a negative electrode material for lithium-ion batteries,silicon monoxide(SiO)suffers from dramatic volume changes during cycling,causing excessive stress within the electrode and resulting in electrode deformation ...As a negative electrode material for lithium-ion batteries,silicon monoxide(SiO)suffers from dramatic volume changes during cycling,causing excessive stress within the electrode and resulting in electrode deformation and fragmentation.This ultimately leads to a decrease in cell capacity.The trends of volume expansion and capacity change of the SiO/graphite(SiO/C)composite electrode during cycling were investigated via in situ expansion monitoring.First,a series of expansion test schemes were designed,and the linear relationship between negative electrode expansion and cell capacity degradation was quantitatively analyzed.Then,the effects of different initial pressures on the long-term cycling performance of the cell were evaluated.Finally,the mechanism of their effects was analyzed by scanning electron microscope.The results show that after 50 cycles,the cell capacity decreases from 2.556 mAh to 1.689 mAh,with a capacity retention ratio(CRR)of only 66.08%.A linear relationship between the capacity retention ratio and thickness expansion was found.Electrochemical measurements and scanning electron microscope images demonstrate that intense stress inhibits the lithiation of the negative electrode and that the electrode is more susceptible to irreversible damage during cycling.Overall,these results reveal the relationship between the cycling performance of SiO and the internal pressure of the electrode from a macroscopic point of view,which provides some reference for the application of SiO/C composite electrodes in lithium-ion batteries.展开更多
One of the detection objectives of the Chinese Asteroid Exploration mission is to investigate the space environment near the Main-belt Comet(MBC,Active Asteroid)311P/PANSTARRS.This paper outlines the scientific object...One of the detection objectives of the Chinese Asteroid Exploration mission is to investigate the space environment near the Main-belt Comet(MBC,Active Asteroid)311P/PANSTARRS.This paper outlines the scientific objectives,measurement targets,and measurement requirements for the proposed Gas and Ion Analyzer(GIA).The GIA is designed for in-situ mass spectrometry of neutral gases and low-energy ions,such as hydrogen,carbon,and oxygen,in the vicinity of 311P.Ion sampling techniques are essential for the GIA's Time-of-Flight(TOF)mass analysis capabilities.In this paper,we present an enhanced ion sampling technique through the development of an ion attraction model and an ion source model.The ion attraction model demonstrates that adjusting attraction grid voltage can enhance the detection efficiency of low-energy ions and mitigate the repulsive force of ions during sampling,which is influenced by the satellite's surface positive charging.The ion source model simulates the processes of gas ionization and ion multiplication.Simulation results indicate that the GIA can achieve a lower pressure limit below 10-13Pa and possess a dynamic range exceeding 10~9.These performances ensure the generation of ions with stable and consistent current,which is crucial for high-resolution and broad dynamic range mass spectrometer analysis.Preliminary testing experiments have verified GIA's capability to detect gas compositions such as H2O and N2.In-situ measurements near 311P using GIA are expected to significantly contribute to our understanding of asteroid activity mechanisms,the evolution of the atmospheric and ionized environments of main-belt comets,the interactions with solar wind,and the origin of Earth's water.展开更多
基金supported by the Project of State Grid Hebei Electric Power Co.,Ltd.(SGHEYX00SCJS2100077).
文摘Crop water stress index(CWSI)is widely used for efficient irrigation management.Precise canopy temperature(T_(c))measurement is necessary to derive a reliable CWSI.The objective of this research was to investigate the influences of atmospheric conditions,settled height,view angle of infrared thermography,and investigating time of temperature measuring on the performance of the CWSI.Three irrigation treatments were used to create different soil water conditions during the 2020-2021 and 2021-2022 winter wheat-growing seasons.The CWSI was calculated using the CWSI-E(an empirical approach)and CWSI-T(a theoretical approach)based on the T_(c).Weather conditions were recorded continuously throughout the experimental period.The results showed that atmospheric conditions influenced the estimation of the CWSI;when the vapor pressure deficit(VPD)was>2000 Pa,the estimated CWSI was related to soil water conditions.The height of the installed infrared thermograph influenced the T_(c)values,and the differences among the T_(c)values measured at height of 3,5,and 10 m was smaller in the afternoon than in the morning.However,the lens of the thermometer facing south recorded a higher T_(c)than those facing east or north,especially at a low height,indicating that the direction of the thermometer had a significant influence on T_(c).There was a large variation in CWSI derived at different times of the day,and the midday measurements(12:00-15:00)were the most reliable for estimating CWSI.Negative linear relationships were found between the transpiration rate and CWSI-E(R^(2)of 0.3646-0.5725)and CWSI-T(R^(2)of 0.5407-0.7213).The relations between fraction of available soil water(FASW)with CWSI-T was higher than that with CWSI-E,indicating CWSI-T was more accurate for predicting crop water status.In addition,The R^(2)between CWSI-T and FASW at 14:00 was higher than that at other times,indicating that 14:00 was the optimal time for using the CWSI for crop water status monitoring.Relative higher yield of winter wheat was obtained with average seasonal values of CWSI-E and CWSI-T around 0.23 and 0.25-0.26,respectively.The CWSI-E values were more easily influenced by meteorological factors and the timing of the measurements,and using the theoretical approach to derive the CWSI was recommended for precise irrigation water management.
文摘Two dynamic grey models DGM (1, 1) for the verification cycle and the lifecycle of measuring instrument based on time sequence and frequency sequence were set up, according to the statistical feature of examination data and weighting method. By a specific case, i.e. vernier caliper, it is proved that the fit precision and forecast precision of the models are much higher, the cycles are obviously different under different working conditions, and the forecast result of the frequency sequence model is better than that of the time sequence model. Combining dynamic grey model and auto-manufacturing case the controlling and information subsystems of verification cycle and the lifecycle based on information integration, multi-sensor controlling and management controlling were given. The models can be used in production process to help enterprise reduce error, cost and flaw.
文摘The principle and method of both radar target imaging and velocity measurement simultaneously based on step frequency waveforms is presented. Velocity compensation is necessary in order to obtain the good High resolution range profile since this waveform is greatly sensitive to the Doppler shift. The velocity measurement performance of the four styles is analyzed with two pulse trains consisted of positive and negative step frequency waveforms. The velocity of targets can be estimated first coarsely by using the pulse trains with positive-positive step frequency combination, and then fine by positive-negative combination. Simulation results indicate that the method can accomplish the accurate estimation of the velocity with efficient computation and good anti-noise performance and obtain the good HRRP simultaneously.
文摘Based on the characters of plant potentials, it introduced the construction and technology in developing the measuring system of plant electrical potentials, the input impedance of the amplifier must be enough high(= 1010～ 1012Ω) in order to measuring the plant weak signals and ensuring high common mode rejection ratio (CMRR). And wavelet transform was applied in denoising based on cross-validation (CV)threshold value. the experiment showed that this system could effectively detect the change of plant potentials,four-week old cucumber was stimulated by heat wounding, the variation potential (VP) and action potential(AP) would be evoked, the AP's varying amplitude can reach 40mV; the AP changed very fast, its duration time is about 0.01～0.02s and its amplitude often change from 15μV～5mV.
基金Project Supported by National Development and Reform Commission(No.[2006]2709)
文摘Thyristor valve is one of the key equipments for ultra high voltage direct current(UHVDC) power transmission projects.Before being installed on site,they need to be tested in a laboratory in order to verify their operational performance to satisfy the technical specification of project related.Test facilities for operational tests of thyristor valves are supposed to enable to undertake more severe electrical stresses than those being applied in the thyristor valves under test(test objects).On the other hand,the stresses applied into the test objects are neither higher nor lower than specified by the specification,because inappropriate stresses applied would result in incorrect evaluation of performance on the test objects,more seriously,would cuase the damage of test objects with expensive cost losing.Generally,the process of operational tests is complicated and performed in a complex synthetic test circuit(hereafter as STC),where there are a lot of sensors used for measuring,monitoring and protection on line to ensure that the test circuit functions in good condition.Therefore,the measuring systems embedded play a core role in STC,acting like "eyes".Based on the first project of building up a STC in China,experience of planning measuring systems is summarized so as to be referenced by related engineers.
基金Projects(2006BAJ01A02-02-052006BAJ04B05-1+1 种基金2006BAJ02A09) supported by the National Key Technological Research and Development Program of Chinaproject(50978261) supported by the National Natural Science Foundation of China
文摘Comparison of thermal performance between a green roof room and a bare roof room was presented during the cooling period in Shanghai. The results show that the electricity can be saved about 0.08 kW·h/(d·m2),and the heat flux can be reduced by about 70%; the inner surface temperature variation is about 1.0 ℃ comparing with the indoor temperature when using the green roof,and the extra equivalent heat resistance is 1.0 m2·K/W.
文摘The principles for measuring characteristic grain sizes of materials, such as fully-dense single phase materials, porous materials and materials with isolated second phase particles, are developed on the basis of its definition associated closely with the surface area per unit volume, Sv, of grain. The focus of the measuring principles of the characteristic grain size is put on determining Sv of grains. Unlike the measurement of average grain size commonly used, G, correcting factors such as grain shape and grain size distribution factors, will not be applied to the determination of the characteristic grain size, Gc, due to its unique geometric meaning and the measure precision of Sv being guaranteed by quantitative stereological technique and gas adsorption method. The measurement of Gc can be directly carried out on the polished and etched cross section of materials, similar to the measuremernt of the average grain size using the Heyn intercept method.
文摘Based on the computer integrated and flexible laser p rocessing system, we developed an intelligent measuring sub-system. A novel mod el has been built to compensate the deviations of the main frame-structure, and a laser tracker system is applied to calibrate the accuracy of the system. Anal yzing the characteristics of all kind surfaces of automobile outer penal moulds and dies, the surface and border to be measured and processed are classified int o four types. A 2-D adaptive measuring method based on Bzier curve and a 3 -D adaptive measuring method based on Spline curve are developed for different types of surface. During the data processing, a 3-D probe compensation method i s described in details. The control software of the sub-measuring system is des cribed. Some measuring experiments are carried out to testify the methods.
文摘The work of quantitative studying the effect of technological progress on economic growth, being of great complexity and far-reaching significance, has become a quite popular research topic in the world. In recent years there are a large number of scientists who are engaged in this research both at home and abroad.
文摘The revolution of information technology within the p ast twenty years has dramatically changed the picture of our economy. Numerous n ew possibilities of communication have let competition advantages for many compa nies and even advantageous macroeconomic consequences emerge on national and international level. Through newly developed information technologies the knowl edge base of market participants improves with a concurrent reduction of the inf ormation obtaining costs. As a result considerable competition advantages develo p for those companies acting in E-commerce networks. These advantages of the la test development lead to macroeconomic effects on national level, if the effecti veness and efficiency increasing possibilities are used more strongly than in ot her countries. Positive international effects arise since the allocation effic iency is increased through intensified competition between different market pa rticipants in various countries. This in turn leads to an increase in wo rldwide prosperity. This causal chain however is not yet realistic to the whole extent, as such an i ncreased transparency of information is not necessarily accepted by all market p articipants. Otherwise a considerable productivity increase would already have o ccurred in industrial countries. Overall the question arises, whether the change s in the competition situation make single enterprises technically more effectiv e, concurrently however deteriorate the efficiency of the entire market through informational asymmetries. To answer these and further questions and to measure the effectiveness and effic iency of various E-commerce networks an interdisciplinary analysis platform is to be developed. With the help of this platform, it should be possible to examin e single and macroeconomic questions, reveal temporal connections and to analyse aspects of business management and national economy, information management, em ployment politics and finance politics. For this, various part-models for the i ndividual knowledge disciplines have to be generated and brought together in the platform. This platform allows various users to make the right decisions (effec tiveness) with the help of the developed models and to competently estimate the effects (efficiency). Currently models of the individual knowledge disciplines (business management, e conomics, computer science) are being developed within the research project EEE. con. This project deals with the question of Supply Chain Management (SCM), E-P rocurement, with the implementation of inter-organisational information systems , as well as various market, competition and organisation models. The department of economics and computer science from Prof. Dr.-Ing. habil. W. Dangelmaier particularly deals with the development of an agent controlled SCM- communication model which is part of the E-commerce analysis platform. Both are described in this paper. Furthermore, a unified modelling language in order to allow a prototypic implementation of the analysis tool and to make the work with other project participants and external participants easier is decided upon wit hin this project.
基金supported by the National Natural Science Foundation of China(71571189)the State Key Laboratory of Air Traffic Management System and Technology(SKLATM201806)
文摘Measuring the business-IT alignment(BITA)of an organization determines its alignment level,provides directions for further improvements,and consequently promotes the organizational performances.Due to the capabilities of enterprise architecture(EA)in interrelating different business/IT viewpoints and elements,the development of EA is superior to support BITA measurement.Extant BITA measurement literature is sparse when it concerns EA.The literature tends to explain how EA viewpoints or models correlate with BITA,without discussing where to collect and integrate EA data.To address this gap,this paper attempts to propose a specific BITA measurement process through associating a BITA maturity model with a famous EA framework:DoD Architectural Framework 2.0(DoDAF2.0).The BITA metrics in the maturity model are connected to the meta-models and models of DoDAF2.0.An illustrative ArchiSurance case is conducted to explain the measurement process.Systematically,this paper explores the process of BITA measurement from the viewpoint of EA,which helps to collect the measurement data in an organized way and analyzes the BITA level in the phase of architecture development.
基金supported by the National Natural Science Foundation of China(61401389).
文摘The advancement of small satellites is promoting the development of distributed satellite systems,and for the latter,it is essential to coordinate the spatial and temporal relations between mutually visible satellites.By now,dual one-way ranging(DOWR)and two-way time transfer(TWTT)are generally integrated in the same software and hardware system to meet the limitations of small satellites in terms of size,weight and power(SWaP)consumption.However,studies show that pseudo-noise regenerative ranging(PNRR)performs better than DOWR if some advanced implementation technologies are employed.Besides,PNRR has no requirement on time synchronization.To apply PNRR to small satellites,and meanwhile,meet the demand for time difference measurement,we propose the round-way time difference measurement,which can be combined with PNRR to form a new integrated system without exceeding the limits of SWaP.The new integrated system can provide distributed small satellite systems with on-orbit high-accuracy and high-precision distance measurement and time difference measurement in real time.Experimental results show that the precision of ranging is about 1.94 cm,and that of time difference measurement is about 78.4 ps,at the signal to noise ratio of 80 dBHz.
基金Project(07JJ6133) supported by the Natural Science Foundation of Hunan Province, China
文摘A new non-invasive blood glucose measuring apparatus (NBGMA) made up of MSP430F149 SCM (single chip micyoco) was developed,which can measure blood glucose level (BGL) frequently,conveniently and painlessly. The hardware and software of this apparatus were designed,and detecting algorithms based on conservation of energy method (COEM) were presented. According to the law of conservation of energy that the energy derived by human body equals energy consumed by metabolism,and the relationship between convection,evaporation,radiation and the BGL was established. The sensor module was designed. 20 healthy volunteers were involved in the clinical experiment. The BGL measured by an automatic biochemical analyzer (ABA) was set as the reference. Regression analysis was performed to compare the conservation of energy method with the biochemical method,using the 20 data points with blood glucose concentrations ranging from 680 to 1 100 mg/L. Reproducibility was measured for healthy fasting volunteers. The results show that the means of BGL detected by NBGMA and ANA are very close to each other,and the difference of standard deviation (SD) is 24.7 mg/L. The correlative coefficient is 0.807. The coefficient of variation (CV) is 4% at 921.6 mg/L. The resultant regression is evaluated by the Clarke error grid analysis (EGA) and all data points are included in the clinically acceptable regions (region A:100%,region B:0%). Accordingly,it is feasible to measure BGL with COEM.
基金Projects(60473031, 60673155) supported by the National Natural Science Foundation of ChinaProject(2005AA121560) supported by the High-Tech Research and Development Program of China
文摘By analyzing the effect of cross traffic (CT) enforced on packet delay, an improved path capacity measurement method, pcapminp algorithm, was proposed. With this method, path capacity was measured by filtering probe samples based on measured minimum packet-pair delay. The measurability of minimum packet-pair delay was also analyzed by simulation. The results show that, when comparing with pathrate, if the CT load is light, both pcapminp and pathrate have similar accuracy; but in the case of heavy CT load, pcapminp is more accurate than Pathrate. When CT load reaches 90%, pcapminp algorithm has only 5% measurement error, which is 10% lower than that of pathrate algorithm. At any CT load levels, the probe cost of pcapminp algorithm is two magnitudes smaller than that of pathrate, and the measurement duration is one magnitude shorter than that of pathrate algorithm.
文摘As an advanced device for observing atmospheric winds,the spaceborne Doppler Asymmetric Spatial Heterodyne(DASH)interferometer also encounters challenges associated with phase distortion,par-ticularly in limb sounding scenarios.This paper discusses interferogram modeling and phase distortion cor-rection techniques for spaceborne DASH interferometers.The modeling of phase distortion interferograms with and without Doppler shift for limb observation was conducted,and the effectiveness of the analytical expression was verified through numerical simulation.The simulation results indicate that errors propagate layer by layer while using the onion-peeling inversion algorithm to handle phase-distorted interferograms.In contrast,the phase distortion correction algorithm can achieve effective correction.This phase correction method can be successfully applied to correct phase distortions in the interferograms of the spaceborne DASH interferometer,providing a feasible solution to enhance its measurement accuracy.
文摘Risk management often plays an important role in decision making un-der uncertainty.In quantitative risk management,assessing and optimizing risk metrics requires eficient computing techniques and reliable theoretical guarantees.In this pa-per,we introduce several topics on quantitative risk management and review some of the recent studies and advancements on the topics.We consider several risk metrics and study decision models that involve the metrics,with a main focus on the related com-puting techniques and theoretical properties.We show that stochastic optimization,as a powerful tool,can be leveraged to effectively address these problems.
文摘The concept of emissivity has been with the scientific and engineering world since Planck formulated his blackbody radiation law more than a century ago.Nevertheless,emissivity is an elusive concept even for ex⁃perts.It is a vague and fuzzy concept for the wider community of engineers.The importance of remote sensing of temperature by measuring IR radiation has been recognized in a wide range of industrial,medical,and environ⁃mental uses.One of the major sources of errors in IR radiometry is the emissivity of the surface being measured.In real experiments,emissivity may be influenced by many factors:surface texture,spectral properties,oxida⁃tion,and aging of surfaces.While commercial blackbodies are prevalent,the much-needed grey bodies with a known emissivity,are unavailable.This study describes how to achieve a calibrated and stable emissivity with a blackbody,a perforated screen,and a reliable and linear novel IR thermal sensor,18 dubbed TMOS.The Digital TMOS is now a low-cost commercial product,it requires low power,and it has a small form factor.The method⁃ology is based on two-color measurements,with two different optical filters,with selected wavelengths conform⁃ing to the grey body definition of the use case under study.With a photochemically etched perforated screen,the effective emissivity of the screen is simply the hole density area of the surface area that emits according to the blackbody temperature radiation.The concept is illustrated with ray tracing simulations,which demonstrate the approach.Measured results are reported.
基金supported by the Fundamental Research Funds for the Central Universities(WK2090000055)Anhui Provincial Natural Science Foundation of China(2308085QG231).
文摘As a negative electrode material for lithium-ion batteries,silicon monoxide(SiO)suffers from dramatic volume changes during cycling,causing excessive stress within the electrode and resulting in electrode deformation and fragmentation.This ultimately leads to a decrease in cell capacity.The trends of volume expansion and capacity change of the SiO/graphite(SiO/C)composite electrode during cycling were investigated via in situ expansion monitoring.First,a series of expansion test schemes were designed,and the linear relationship between negative electrode expansion and cell capacity degradation was quantitatively analyzed.Then,the effects of different initial pressures on the long-term cycling performance of the cell were evaluated.Finally,the mechanism of their effects was analyzed by scanning electron microscope.The results show that after 50 cycles,the cell capacity decreases from 2.556 mAh to 1.689 mAh,with a capacity retention ratio(CRR)of only 66.08%.A linear relationship between the capacity retention ratio and thickness expansion was found.Electrochemical measurements and scanning electron microscope images demonstrate that intense stress inhibits the lithiation of the negative electrode and that the electrode is more susceptible to irreversible damage during cycling.Overall,these results reveal the relationship between the cycling performance of SiO and the internal pressure of the electrode from a macroscopic point of view,which provides some reference for the application of SiO/C composite electrodes in lithium-ion batteries.
基金Supported by the National Natural Science Foundation of China(42474239,41204128)China National Space Administration(Pre-research project on Civil Aerospace Technologies No.D010301)Strategic Priority Research Program of the Chinese Academy of Sciences(XDA17010303)。
文摘One of the detection objectives of the Chinese Asteroid Exploration mission is to investigate the space environment near the Main-belt Comet(MBC,Active Asteroid)311P/PANSTARRS.This paper outlines the scientific objectives,measurement targets,and measurement requirements for the proposed Gas and Ion Analyzer(GIA).The GIA is designed for in-situ mass spectrometry of neutral gases and low-energy ions,such as hydrogen,carbon,and oxygen,in the vicinity of 311P.Ion sampling techniques are essential for the GIA's Time-of-Flight(TOF)mass analysis capabilities.In this paper,we present an enhanced ion sampling technique through the development of an ion attraction model and an ion source model.The ion attraction model demonstrates that adjusting attraction grid voltage can enhance the detection efficiency of low-energy ions and mitigate the repulsive force of ions during sampling,which is influenced by the satellite's surface positive charging.The ion source model simulates the processes of gas ionization and ion multiplication.Simulation results indicate that the GIA can achieve a lower pressure limit below 10-13Pa and possess a dynamic range exceeding 10~9.These performances ensure the generation of ions with stable and consistent current,which is crucial for high-resolution and broad dynamic range mass spectrometer analysis.Preliminary testing experiments have verified GIA's capability to detect gas compositions such as H2O and N2.In-situ measurements near 311P using GIA are expected to significantly contribute to our understanding of asteroid activity mechanisms,the evolution of the atmospheric and ionized environments of main-belt comets,the interactions with solar wind,and the origin of Earth's water.
