In an injection moulding process, the mould cooling s ystem is very important as an efficient and uniform cooling effect can improve b oth the productivity and part quality. Due to the complexity of the process, muc h...In an injection moulding process, the mould cooling s ystem is very important as an efficient and uniform cooling effect can improve b oth the productivity and part quality. Due to the complexity of the process, muc h research on the mould cooling analysis and cooling design optimization has bee n focused on the core and the cavity, excluding other systems of injection mould s. However, the runner system introduces a considerable amount of heat into the mould. In recent years, more and more hot runner systems are being applied in th e moulding industry to save material and decrease losses of injection pressure. This raises the need to include the hot runner system in the cooling analysis. I n this paper, a photo frame part was studied. The mould was built with a hot run ner system. Two thermal sensors were installed: one measures the temperature of lateral surface of hot runner nozzle; the other measures the plastic temperature from the core side. A pressure sensor was also installed to measure the pressur e of the core impression. Cooling analysis was performed using ABAQUS, ananalysi s software based on the Finite Element Method (FEM). The assembly including core , cavity and plastic part was modeled. Heat conduction from hot runner to cavity and from polymer melt to the mould and force convection on the cooling channel surfaces were studied. The natural convection between the ambient air and the ex terior mould surface was ignored. The simulations were adjusted with the experim ental results to find out the heat input from hot runner and its influence on mo uld cooling. Finally, the optimal cooling design and optimal injection condition were obtained.展开更多
The characteristic of metallographic structure of the SnSb alloy moulds is that hard particles are distributed on the soft metal matrix. Great difference of the hard particles and the soft metal matrix’hardness makes...The characteristic of metallographic structure of the SnSb alloy moulds is that hard particles are distributed on the soft metal matrix. Great difference of the hard particles and the soft metal matrix’hardness makes moulds’polishing become difficult. When a rigid grindstone is used to polish the surface of the SnSb alloy mould, the hard abrasives fall off and are embed in the soft matrix of SnSb alloy and while the process, the grinding chips are able to block the gap on the grindstone surface and enable the grindstone to blunt, which brings about the polished area on the surface of the mould is seriously squeezed and deformed and the crystal lattice of SnSb alloys is seriously distorted, and the work hardening takes place. At the same time, the rigid grindstone is easy to scratch the surface of the SnSb alloy mould. Owing to the above reasons, it is difficult to reduce surface roughness and improve the surface quality of SnSb alloy moulds. Taking use of the CAD/CAM technique and the complex processing of combining electrolyzing polishing and mechanical polishing with the magnetic force, mould’s polishing automation is realized on the numerical control machine tool. This complex processing is finished under a comprehensive action as the following: 1. Electrolyzing polishing action Under the electric field, the electrolyte between the elastic grind wheel and the mould is ionized, which electrolyzes the metal of the mould’s surface. The electrolyzing speed of convex peak on the mould’s surface is faster than that of concave valley, which levels the mould’s surface. 2. Mechanical Polishing action During electrolyzing, a dense passive film of low hardness is formed on the mould’s surface. While polishing, soft grinding wheel scraps the passive film on the conven peak easily, and the new metal surface is exposed, then, a new passive film is formed again, going round and round, the conven peak on the mould’s surface is leveled quickly. 3. Magnetic force action The charged particles in electric field will be acted by the Lorentz force in magnetic field. The field plays a stirring part on electrolyte and reduces electrochemical polarization and concentration polarization, and accelerates the electrochemical reaction. The complex polishing process is not only of high efficiency, but also of good surface quality and provides a good effective method for the non-ferrous metal polishing. When the mould is polished, a speed-raising tool system is used and it can increase the grinding wheel spindle’s speed up to five times. This paper describes the SnSb alloy moulds’polishing steps, grinding wheel speed-raising tool system, polishing principle and the results.展开更多
Today, the time-to-market for plastic products ar e getting shorter, thus the lead-time for making the injection mould is decreasin g. There is potential in timesavings in the mould design stage because the design pro...Today, the time-to-market for plastic products ar e getting shorter, thus the lead-time for making the injection mould is decreasin g. There is potential in timesavings in the mould design stage because the design process that is repeatable for every mould design can be standardized. T he preliminary work of any final plastic injection mould design is to always pro vide an initial design of the mould assembly for product designers (customers) p rior to receiving the final product CAD data. Traditionally and even up till no w, this initial design is always created using 2D CAD packages. The information used for the initial design is based on the technical discussion checklist, in which most mould makers have their own standards. This checklist is also being used as a quotation since the most basic information of the mould in the particu lar project is being recorded in it. The basic information in this checklist in cludes the number of cavities, the type of mould base to be used, the moulding m achine to be used for the moulding, the type of gating system, the type of resin material used and its shrinkage value etc. Information on special requirements such as the number of sliders or lifters to be used is also listed in the check list. At this stage, there is still no information on the cooling and ejection design since they are greatly dependent on the final product CAD data. This res earch focuses on the methodology of providing the initial design in 3D solid bas ed on the technical discussion checklist, which takes the role of the overall st andard template since every sub-design has its own standard template. An examp le of a sub-design that has its own standard template is the cavity layout desi gn. The cavity layout for plastic injection moulds can be designed by controlli ng the geometrical parameters using a standardization template. The standardiza tion template for the cavity layout design consists of configurations for the po ssible layouts. Each configuration of the layout design has its own layout desi gn table of all the geometrical parameters. This standardization template is pr e-defined in the layout design level of the mould assembly design. This ensure s that the required configuration can be loaded into the mould assembly design v ery quickly without having the need to redesign the layout. This makes it usefu l for technical discussions between the product designers and mould designers pr ior to the manufacture of the mould. Changes can be made to the 3D cavity layou t design immediately during the discussions thus the savings in time and avo idance of miscommunications.展开更多
This paper focuses on the high-temperature tensile failure mechanism of RTM(resin transfer moulding)-made symmetric and asymmetric composite T-joints.The failure modes as well as the load-displacement curves of symmet...This paper focuses on the high-temperature tensile failure mechanism of RTM(resin transfer moulding)-made symmetric and asymmetric composite T-joints.The failure modes as well as the load-displacement curves of symmetric(three specimens)and asymmetric(three specimens)composite T-joints were determined by tensile tests at room and high temperatures.Progressive damage models(PDMs)of symmetric and asymmetric composite T-joints at room and high temperatures were established based on mixed criteria,and the result predicted from the aforementioned PDMs were compared with experimental data.The predicted initial and final failure loads and failure modes are in good agreement with the experimental results.The failure mechanisms of composite T-joints at different temperatures were investigated by scanning electron microscopy.The results reveal that while the failure mode of asymmetric T-joints at high temperatures resembles that at room temperature,there is a difference in the failure modes of symmetric T-joints.The ultimate failure load of symmetric and asymmetric T-joints at elevated temperatures increases and reduces by 18.4%and 4.97%,albeit with a more discrete distri-bution.This work is expected to provide us with more knowledge about the usability of composite T-joints in elevated temperature environments.展开更多
Near infrared spectrometer technology under a wavelength range of 918-1045 nm was used to rapidly detect paddy rice that was stored at 5℃, 15℃ and 25℃. A total of 121 paddy rice samples were collected from artifici...Near infrared spectrometer technology under a wavelength range of 918-1045 nm was used to rapidly detect paddy rice that was stored at 5℃, 15℃ and 25℃. A total of 121 paddy rice samples were collected from artificial infection with moulds to build the calibration models to calculate the total number colony of moulds based on the principal component regression method and multiple linear regression method. The results of statistical analysis indicated that multiple linear regression method was applicable to the detection of the total number colony of moulds. The correlation of calibration data set was 0.943. The correlation of prediction data set was 0.897. Therefore, the result showed that near infrared spectroscopy could be a useful instrumental method for determining the total number colony of moulds in paddy rice. The near infrared spectroscopy methodology could be applied for monitoring mould contamination in postharvest paddy rice during storage and might become a powerful tool for monitoring the safety of the grain.展开更多
The finite element analysis and the optimum design of aluminum profile extrusion mould were investigated using the ANSYS software and its parameterized modeling method. The optimum dimensions of the mould were obtaine...The finite element analysis and the optimum design of aluminum profile extrusion mould were investigated using the ANSYS software and its parameterized modeling method. The optimum dimensions of the mould were obtained. It is found that the stress distribution is very uneven, and the stress convergence is rather severe in the bridge of the aluminum profile extrusion mould. The optimum height of the mould is 70.527 mm, and the optimum radius of dividing holes are 70.182 mm and 80.663 mm. Increasing the height of the mould in the range of 61.282 mm to 70.422 mm can prolong its longevity, but when the height is over 70.422 mm, its longevity reduces.展开更多
The effects of process parameters in rapid heat cycle moulding （RHCM） on parts warpage were investigated. A vehicle-used blue-tooth front shell （consisting of ABS material） was considered as a part example manufac...The effects of process parameters in rapid heat cycle moulding （RHCM） on parts warpage were investigated. A vehicle-used blue-tooth front shell （consisting of ABS material） was considered as a part example manufactured by RHCM method. The corresponding rapid heat response mould with an innovational conformal heating/cooling channel system and a dynamic mould temperature control system based on the Jll-W-160 type precise temperature controller was proposed. During heating/cooling process, the mould was able to be heated from room temperature to 160 ~C in 6 s and then cooled to 80 ~C in 22 s. The effects of processing conditions in RHCM on part warpage were investigated based on the single factor experimental method and Taguchi theory. Results reveal that the elevated mould temperature reduces unwanted freezing during the injection stage, thus improving mouldability and enhancing part quality, whereas the overheated of mould temperature will lead to defective product. The feasible mould temperature scope in RHCM should be no higher than 140 ~C, and the efficient mould temperature scope should be around the polymer heat distortion temperature. Melt temperature as well as injection pressure effects on warpage can be divided into two stages The lower stage gives a no explicit effect on warpage whereas the higher stage leads to a quasi-linear downtrend. But others affect the warpage as a V-type fluctuation, reaching to the minimum around the heat distortion temperature. Under the same mould temperature condition, the effects of process parameters on warpage decrease according to the following order, packing time, packing pressure, melt temperature, injection pressure and cooling time, respectively.展开更多
With the rapid development of information and multi me dia technologies, the demand for the optical plastic aspheric elements used in o pto-electronic devices, camera, optical disc and projector lens etc. has been i n...With the rapid development of information and multi me dia technologies, the demand for the optical plastic aspheric elements used in o pto-electronic devices, camera, optical disc and projector lens etc. has been i ncreased rapidly in the recent years. The key technologies of fabrication of asp heric plastic lens are the design and manufacturing moulds, selection of proper injection moulding equipment, and optimization of injection moulding parameters etc. In this paper, the effect of injection pressure, moulding temperature, cool ing time and injection speed on the surface profile of the lenses during injecti on and holding process is investigated. Surface quality of plastic lenses is mea sured by Talysurf Texture Measuring System. The experimental results showed that the injection pressure and moulding temperature are important parameters compar ing to cooling time and injection speed. A bit change of injection pressure or m oulding temperature will affect the property of the surface profile. Either incr easing injection pressure or mould temperature can achieve less shrinkage. Other wise, a lower injection pressure will produce more shrinkage, more air traps and a lower mould temperature results greater warp and higher shrinkage. The dynami c process of injection for optical plastic lenses is simulated by 3D Moldflow pl astic Insight software (MPI). The MPI will help us to optimize injection mouldin g parameters.展开更多
In this paper the hit force of firing bullet on bulletproof helmet has been computed and the test device has been described. The device is divided into two parts: 1) The bullet, helmet and mould are in one system, u...In this paper the hit force of firing bullet on bulletproof helmet has been computed and the test device has been described. The device is divided into two parts: 1) The bullet, helmet and mould are in one system, using moment theorem to calculate the hit force; 2) The mould, sensor and support pole are in one system, using the method in reference [1] that measures the dynamic strain and displacement of simulate target of bulletproof clothes. We compute the transfigure energy and momentum energy when hitting the mould, the work done by the sensor and the expend energy of support pole. We get the hit force of helmet using energy balance principle. The result is according with the test and has been used to design the GGK93T bulletproof helmet and other serial products.展开更多
In an injection moulding process, the parallelism b et ween the tie bars of the injection moulding machine is very important as it will affect the mould closing and clamping system. In recent years, more and more ho t...In an injection moulding process, the parallelism b et ween the tie bars of the injection moulding machine is very important as it will affect the mould closing and clamping system. In recent years, more and more ho t runner systems are being applied in the moulding industry to save material and decrease the losses of injection pressure. Heat transfer from hot runner system from the fixed half which is secured in the fix machine platen could transmit s o much heat that it may cause high temperature differential between the machine fix platen and moving platen. This will cause the tie bar to become unparallel. Part quality will be compromised and the wear of the tie bar will be excessive. Overhaul of the tie bar may be necessary after a short period of time which is c ostly. This raises the need to analyze the heat transfer from the hot runner sys tem to the machine fix platen and the methods of isolating or minimizing the hea t transfer. In this case study, a photo lens article mould was used. The mould w as built with a direct hot runner nozzle system. Heat conduction from hot runner and machine screw to machine fix platen were studied based on either using high temperature heat insulating plate put in placed between the mould and the mould ing machine fix platen or drill cooling channels in the front mould clamping pla te. The high temperature insulator is very costly as it is made out of glass re inforced polymer composite material. Experimental results were obtained and anal yzed to find the best method to minimize the unwanted heat transfer using the ch eapest and most effective method.展开更多
Cristobalite SiO2 can be obtained from the fused silica ceramic waste of ploysilicon plant, due to the phase conversion of fused silica to cristobalite during the process of polysilicon ingot. Cristobalite powder mate...Cristobalite SiO2 can be obtained from the fused silica ceramic waste of ploysilicon plant, due to the phase conversion of fused silica to cristobalite during the process of polysilicon ingot. Cristobalite powder materials with high purity are manufactured by milling the discarded waste above. Thermal expansion rate of the cristobalite and gypsum bonding moulds were studied, which show that the thermal expansion of the cristobalite phase transition could effectively compensate for the shrinkage of the gypsum at the temperature between 200 ℃ and 400 ℃. Casting experiments with copper alloy show that the cristobalite can improve the thermal performance of moulds for precise casting of jewelry.展开更多
On going trend of miniaturization in electronic rel at ed parts, which is an average of two times in every 5～7 years introduce grindin g challenges. In grinding process, the surface waviness control of thin parts is ...On going trend of miniaturization in electronic rel at ed parts, which is an average of two times in every 5～7 years introduce grindin g challenges. In grinding process, the surface waviness control of thin parts is an ardent task due to its warpage, induced by the high specific grinding energy (2～10 J/mm 3). Therefore, coolant is often used to avoid thermal damage, obtai n better surface integrity and to prolong wheel life. However coolant, the incomp ressibility media introduce high forces at the grinding zone creating dimensiona l as well as shape instability. In view of these situations chilled air was ap plied in place of conventional coolant. The chilled air is produced using a two -stage vapor compression refrigeration cycle with characteristics of: temperatu re -35 ℃, pressure 0.2～0.3 MPa and flow rate 0.4 m 3/min. Also traces of eco - oil mist that encompass the chilled air are supplied to the grinding zone. B oth chilled air and eco-oil mist are applied through two independent paths of a specially designed twin compartment nozzle for maximizing the penetration. This paper investigates the grinding characteristics of mold insert which is closer to M2 tool steel (component widely used in connector industries) when using chil led air as coolant media. Grinding experiments were conducted using a vitrified bond CBN wheel (B91N100V) and a surface grinder. Initial study was focussed on establishing the most suita ble clamping method for the thin mold insert. FEM analysis and grinding experime nt studies were performed to quantitatively analyze the clamping induced deflect ion. Waviness value (W t) of (24～62) μm was achieved for resin clampi n g whereas (4～8) μm, (4～6) μm were achieved for magnetic and wax clamping res pe ctively. Wax clamping is predominantly used in all the grinding experiments that characterize the grinding process, which use chilled air as the coolant media. Between 0.15 to 0.9 mm 3/mm.s of specific material removal rate, ground sur face temperature of mold insert was increased from 0.3 ℃ to 59.7 ℃ for chi lled air. For the similar grinding conditions with the coolant fluid an increase from 0.9 ℃ to 14.4 ℃ was recorded. With increase of specific material removal rate from 0.15 to 0.65 mm 3/mm.s, F t/F n ratio was increased from (0.2 to 0.4), (0.6 to 1.67) for wet coolant and chilled air respectively. Despite of high F t/F n ratio and ground surface temperature, chilled air method has shown a surface waviness, W t from (2 to 5.6) μm. Microstructure examination of chilled air produced ground surface was comparable to those of using coolant fluids. Surface finish, R a of (0.45～0.7) μm was achieved for mold insert . This work will enable to have clear understanding about the quantitative influe nce of chilled air as well as the clamping method against the surface waviness o f thin mold insert.展开更多
To evaluate the bioeompatibility of MIM 316L stainless steel,the percentage of S-period cells were detected by flow cytometry after L929 incubated with extraction of MIM 316L stainless steel,using titanium implant mat...To evaluate the bioeompatibility of MIM 316L stainless steel,the percentage of S-period cells were detected by flow cytometry after L929 incubated with extraction of MIM 316L stainless steel,using titanium implant materials of clinical application as the contrast.Both materials were implanted in animal and the histopathological evaluations were carried out.The statistical analyses show that there are no significant differences between two groups(P>0.05),which demonstrates that MIM 316L stainless steel has a good biocompatibility.展开更多
Obtaining the optimal values of the parameters for th e design of a required mould and the operation of the moulding process are diffi cult, this is due to the complexity of product geometry and the variation of pla s...Obtaining the optimal values of the parameters for th e design of a required mould and the operation of the moulding process are diffi cult, this is due to the complexity of product geometry and the variation of pla stic material properties. The typical parameters for the mould design and mouldi ng process are melt flow length, injection pressure, holding pressure, back pres sure, injection speed, melt temperature, mould temperature, clamping force, inje ction time, holding time and cooling time. This paper discusses the difficulties of using the current computer aided optimization methods to acquire the values of the parameters. A method that is based on the concept of genetic algorithm is proposed to overcome the difficulties. The proposed method describes in details on how to attain the optimal values of the parameters form a given product geom etry.展开更多
With the use of multimedia which combines the use o f text, sound, images, motion video and animation, it is more efficient for studen ts to learn mould design interactively. A program is created using several multi m...With the use of multimedia which combines the use o f text, sound, images, motion video and animation, it is more efficient for studen ts to learn mould design interactively. A program is created using several multi media software to simulate the mechanism of moulding processes in order to let s tudents understand the concept of mould design. In addition, students can even access the program through the Internet. Therefore, the software is defined as Multimedia and Internet Technology (MIT) program. The MIT program consists of four sections: (i) simulation of mould mechanisms, ( ii) cooling system, (iii) material information and (iv) games for tutorials. Sec tion One covers the basic operations of different types of moulds such as two-p late mould, three-plate mould, split mould, side-core mould and mould with und ercuts. Section Two introduces different types of cooling systems such as bubble r, baffle, cooling circuits, etc. Section Three provides some useful material in formation for mould design. Section Four contains games of matching mould compon ents, mould design problem finding and multiple choice questions to test student s how much they understand mould design concept. Multimedia is highly effective particularly in teaching and learning. It changes the nature of learning itself. It makes reading dynamic by giving words an impo rtant new dimension. It allows students to see, hear and do simultaneously, thus significantly reducing average learning time. Furthermore, through cooperative learning on Internet, students can access the program, share data or search info rmation anytime anywhere. Therefore, Multimedia and Internet Technology is one o f the vital aspects to speed up the realization of information age in society.展开更多
文摘In an injection moulding process, the mould cooling s ystem is very important as an efficient and uniform cooling effect can improve b oth the productivity and part quality. Due to the complexity of the process, muc h research on the mould cooling analysis and cooling design optimization has bee n focused on the core and the cavity, excluding other systems of injection mould s. However, the runner system introduces a considerable amount of heat into the mould. In recent years, more and more hot runner systems are being applied in th e moulding industry to save material and decrease losses of injection pressure. This raises the need to include the hot runner system in the cooling analysis. I n this paper, a photo frame part was studied. The mould was built with a hot run ner system. Two thermal sensors were installed: one measures the temperature of lateral surface of hot runner nozzle; the other measures the plastic temperature from the core side. A pressure sensor was also installed to measure the pressur e of the core impression. Cooling analysis was performed using ABAQUS, ananalysi s software based on the Finite Element Method (FEM). The assembly including core , cavity and plastic part was modeled. Heat conduction from hot runner to cavity and from polymer melt to the mould and force convection on the cooling channel surfaces were studied. The natural convection between the ambient air and the ex terior mould surface was ignored. The simulations were adjusted with the experim ental results to find out the heat input from hot runner and its influence on mo uld cooling. Finally, the optimal cooling design and optimal injection condition were obtained.
文摘The characteristic of metallographic structure of the SnSb alloy moulds is that hard particles are distributed on the soft metal matrix. Great difference of the hard particles and the soft metal matrix’hardness makes moulds’polishing become difficult. When a rigid grindstone is used to polish the surface of the SnSb alloy mould, the hard abrasives fall off and are embed in the soft matrix of SnSb alloy and while the process, the grinding chips are able to block the gap on the grindstone surface and enable the grindstone to blunt, which brings about the polished area on the surface of the mould is seriously squeezed and deformed and the crystal lattice of SnSb alloys is seriously distorted, and the work hardening takes place. At the same time, the rigid grindstone is easy to scratch the surface of the SnSb alloy mould. Owing to the above reasons, it is difficult to reduce surface roughness and improve the surface quality of SnSb alloy moulds. Taking use of the CAD/CAM technique and the complex processing of combining electrolyzing polishing and mechanical polishing with the magnetic force, mould’s polishing automation is realized on the numerical control machine tool. This complex processing is finished under a comprehensive action as the following: 1. Electrolyzing polishing action Under the electric field, the electrolyte between the elastic grind wheel and the mould is ionized, which electrolyzes the metal of the mould’s surface. The electrolyzing speed of convex peak on the mould’s surface is faster than that of concave valley, which levels the mould’s surface. 2. Mechanical Polishing action During electrolyzing, a dense passive film of low hardness is formed on the mould’s surface. While polishing, soft grinding wheel scraps the passive film on the conven peak easily, and the new metal surface is exposed, then, a new passive film is formed again, going round and round, the conven peak on the mould’s surface is leveled quickly. 3. Magnetic force action The charged particles in electric field will be acted by the Lorentz force in magnetic field. The field plays a stirring part on electrolyte and reduces electrochemical polarization and concentration polarization, and accelerates the electrochemical reaction. The complex polishing process is not only of high efficiency, but also of good surface quality and provides a good effective method for the non-ferrous metal polishing. When the mould is polished, a speed-raising tool system is used and it can increase the grinding wheel spindle’s speed up to five times. This paper describes the SnSb alloy moulds’polishing steps, grinding wheel speed-raising tool system, polishing principle and the results.
文摘Today, the time-to-market for plastic products ar e getting shorter, thus the lead-time for making the injection mould is decreasin g. There is potential in timesavings in the mould design stage because the design process that is repeatable for every mould design can be standardized. T he preliminary work of any final plastic injection mould design is to always pro vide an initial design of the mould assembly for product designers (customers) p rior to receiving the final product CAD data. Traditionally and even up till no w, this initial design is always created using 2D CAD packages. The information used for the initial design is based on the technical discussion checklist, in which most mould makers have their own standards. This checklist is also being used as a quotation since the most basic information of the mould in the particu lar project is being recorded in it. The basic information in this checklist in cludes the number of cavities, the type of mould base to be used, the moulding m achine to be used for the moulding, the type of gating system, the type of resin material used and its shrinkage value etc. Information on special requirements such as the number of sliders or lifters to be used is also listed in the check list. At this stage, there is still no information on the cooling and ejection design since they are greatly dependent on the final product CAD data. This res earch focuses on the methodology of providing the initial design in 3D solid bas ed on the technical discussion checklist, which takes the role of the overall st andard template since every sub-design has its own standard template. An examp le of a sub-design that has its own standard template is the cavity layout desi gn. The cavity layout for plastic injection moulds can be designed by controlli ng the geometrical parameters using a standardization template. The standardiza tion template for the cavity layout design consists of configurations for the po ssible layouts. Each configuration of the layout design has its own layout desi gn table of all the geometrical parameters. This standardization template is pr e-defined in the layout design level of the mould assembly design. This ensure s that the required configuration can be loaded into the mould assembly design v ery quickly without having the need to redesign the layout. This makes it usefu l for technical discussions between the product designers and mould designers pr ior to the manufacture of the mould. Changes can be made to the 3D cavity layou t design immediately during the discussions thus the savings in time and avo idance of miscommunications.
基金supported by the Natural Science Foundation of Shanghai(Grant No.24ZR1401700)Fundamental Research Funds for the Central Universities(Grant No.2232022D-28)the Young Elite Scientists Sponsorship Program by the China Association for Science and Technology(Grant No.2016QNRC001).
文摘This paper focuses on the high-temperature tensile failure mechanism of RTM(resin transfer moulding)-made symmetric and asymmetric composite T-joints.The failure modes as well as the load-displacement curves of symmetric(three specimens)and asymmetric(three specimens)composite T-joints were determined by tensile tests at room and high temperatures.Progressive damage models(PDMs)of symmetric and asymmetric composite T-joints at room and high temperatures were established based on mixed criteria,and the result predicted from the aforementioned PDMs were compared with experimental data.The predicted initial and final failure loads and failure modes are in good agreement with the experimental results.The failure mechanisms of composite T-joints at different temperatures were investigated by scanning electron microscopy.The results reveal that while the failure mode of asymmetric T-joints at high temperatures resembles that at room temperature,there is a difference in the failure modes of symmetric T-joints.The ultimate failure load of symmetric and asymmetric T-joints at elevated temperatures increases and reduces by 18.4%and 4.97%,albeit with a more discrete distri-bution.This work is expected to provide us with more knowledge about the usability of composite T-joints in elevated temperature environments.
基金Supported by the National 12th Five-year Plan for Science&Technology Support Fund(2012BAK08B04-02)the Heilongjiang Science and Technology Plan(GC12B404)
文摘Near infrared spectrometer technology under a wavelength range of 918-1045 nm was used to rapidly detect paddy rice that was stored at 5℃, 15℃ and 25℃. A total of 121 paddy rice samples were collected from artificial infection with moulds to build the calibration models to calculate the total number colony of moulds based on the principal component regression method and multiple linear regression method. The results of statistical analysis indicated that multiple linear regression method was applicable to the detection of the total number colony of moulds. The correlation of calibration data set was 0.943. The correlation of prediction data set was 0.897. Therefore, the result showed that near infrared spectroscopy could be a useful instrumental method for determining the total number colony of moulds in paddy rice. The near infrared spectroscopy methodology could be applied for monitoring mould contamination in postharvest paddy rice during storage and might become a powerful tool for monitoring the safety of the grain.
文摘The finite element analysis and the optimum design of aluminum profile extrusion mould were investigated using the ANSYS software and its parameterized modeling method. The optimum dimensions of the mould were obtained. It is found that the stress distribution is very uneven, and the stress convergence is rather severe in the bridge of the aluminum profile extrusion mould. The optimum height of the mould is 70.527 mm, and the optimum radius of dividing holes are 70.182 mm and 80.663 mm. Increasing the height of the mould in the range of 61.282 mm to 70.422 mm can prolong its longevity, but when the height is over 70.422 mm, its longevity reduces.
基金Project(20122BAB206014)supported by National Natural Science Foundation of ChinaProject(51365038)supported by the Natural Science Foundation of Jiangxi Province,ChinaProject(GJJ13068)supported by the Science and Technology Program of Educational Committee of Jiangxi Province,China
文摘The effects of process parameters in rapid heat cycle moulding （RHCM） on parts warpage were investigated. A vehicle-used blue-tooth front shell （consisting of ABS material） was considered as a part example manufactured by RHCM method. The corresponding rapid heat response mould with an innovational conformal heating/cooling channel system and a dynamic mould temperature control system based on the Jll-W-160 type precise temperature controller was proposed. During heating/cooling process, the mould was able to be heated from room temperature to 160 ~C in 6 s and then cooled to 80 ~C in 22 s. The effects of processing conditions in RHCM on part warpage were investigated based on the single factor experimental method and Taguchi theory. Results reveal that the elevated mould temperature reduces unwanted freezing during the injection stage, thus improving mouldability and enhancing part quality, whereas the overheated of mould temperature will lead to defective product. The feasible mould temperature scope in RHCM should be no higher than 140 ~C, and the efficient mould temperature scope should be around the polymer heat distortion temperature. Melt temperature as well as injection pressure effects on warpage can be divided into two stages The lower stage gives a no explicit effect on warpage whereas the higher stage leads to a quasi-linear downtrend. But others affect the warpage as a V-type fluctuation, reaching to the minimum around the heat distortion temperature. Under the same mould temperature condition, the effects of process parameters on warpage decrease according to the following order, packing time, packing pressure, melt temperature, injection pressure and cooling time, respectively.
文摘With the rapid development of information and multi me dia technologies, the demand for the optical plastic aspheric elements used in o pto-electronic devices, camera, optical disc and projector lens etc. has been i ncreased rapidly in the recent years. The key technologies of fabrication of asp heric plastic lens are the design and manufacturing moulds, selection of proper injection moulding equipment, and optimization of injection moulding parameters etc. In this paper, the effect of injection pressure, moulding temperature, cool ing time and injection speed on the surface profile of the lenses during injecti on and holding process is investigated. Surface quality of plastic lenses is mea sured by Talysurf Texture Measuring System. The experimental results showed that the injection pressure and moulding temperature are important parameters compar ing to cooling time and injection speed. A bit change of injection pressure or m oulding temperature will affect the property of the surface profile. Either incr easing injection pressure or mould temperature can achieve less shrinkage. Other wise, a lower injection pressure will produce more shrinkage, more air traps and a lower mould temperature results greater warp and higher shrinkage. The dynami c process of injection for optical plastic lenses is simulated by 3D Moldflow pl astic Insight software (MPI). The MPI will help us to optimize injection mouldin g parameters.
文摘In this paper the hit force of firing bullet on bulletproof helmet has been computed and the test device has been described. The device is divided into two parts: 1) The bullet, helmet and mould are in one system, using moment theorem to calculate the hit force; 2) The mould, sensor and support pole are in one system, using the method in reference [1] that measures the dynamic strain and displacement of simulate target of bulletproof clothes. We compute the transfigure energy and momentum energy when hitting the mould, the work done by the sensor and the expend energy of support pole. We get the hit force of helmet using energy balance principle. The result is according with the test and has been used to design the GGK93T bulletproof helmet and other serial products.
文摘In an injection moulding process, the parallelism b et ween the tie bars of the injection moulding machine is very important as it will affect the mould closing and clamping system. In recent years, more and more ho t runner systems are being applied in the moulding industry to save material and decrease the losses of injection pressure. Heat transfer from hot runner system from the fixed half which is secured in the fix machine platen could transmit s o much heat that it may cause high temperature differential between the machine fix platen and moving platen. This will cause the tie bar to become unparallel. Part quality will be compromised and the wear of the tie bar will be excessive. Overhaul of the tie bar may be necessary after a short period of time which is c ostly. This raises the need to analyze the heat transfer from the hot runner sys tem to the machine fix platen and the methods of isolating or minimizing the hea t transfer. In this case study, a photo lens article mould was used. The mould w as built with a direct hot runner nozzle system. Heat conduction from hot runner and machine screw to machine fix platen were studied based on either using high temperature heat insulating plate put in placed between the mould and the mould ing machine fix platen or drill cooling channels in the front mould clamping pla te. The high temperature insulator is very costly as it is made out of glass re inforced polymer composite material. Experimental results were obtained and anal yzed to find the best method to minimize the unwanted heat transfer using the ch eapest and most effective method.
文摘Cristobalite SiO2 can be obtained from the fused silica ceramic waste of ploysilicon plant, due to the phase conversion of fused silica to cristobalite during the process of polysilicon ingot. Cristobalite powder materials with high purity are manufactured by milling the discarded waste above. Thermal expansion rate of the cristobalite and gypsum bonding moulds were studied, which show that the thermal expansion of the cristobalite phase transition could effectively compensate for the shrinkage of the gypsum at the temperature between 200 ℃ and 400 ℃. Casting experiments with copper alloy show that the cristobalite can improve the thermal performance of moulds for precise casting of jewelry.
文摘On going trend of miniaturization in electronic rel at ed parts, which is an average of two times in every 5～7 years introduce grindin g challenges. In grinding process, the surface waviness control of thin parts is an ardent task due to its warpage, induced by the high specific grinding energy (2～10 J/mm 3). Therefore, coolant is often used to avoid thermal damage, obtai n better surface integrity and to prolong wheel life. However coolant, the incomp ressibility media introduce high forces at the grinding zone creating dimensiona l as well as shape instability. In view of these situations chilled air was ap plied in place of conventional coolant. The chilled air is produced using a two -stage vapor compression refrigeration cycle with characteristics of: temperatu re -35 ℃, pressure 0.2～0.3 MPa and flow rate 0.4 m 3/min. Also traces of eco - oil mist that encompass the chilled air are supplied to the grinding zone. B oth chilled air and eco-oil mist are applied through two independent paths of a specially designed twin compartment nozzle for maximizing the penetration. This paper investigates the grinding characteristics of mold insert which is closer to M2 tool steel (component widely used in connector industries) when using chil led air as coolant media. Grinding experiments were conducted using a vitrified bond CBN wheel (B91N100V) and a surface grinder. Initial study was focussed on establishing the most suita ble clamping method for the thin mold insert. FEM analysis and grinding experime nt studies were performed to quantitatively analyze the clamping induced deflect ion. Waviness value (W t) of (24～62) μm was achieved for resin clampi n g whereas (4～8) μm, (4～6) μm were achieved for magnetic and wax clamping res pe ctively. Wax clamping is predominantly used in all the grinding experiments that characterize the grinding process, which use chilled air as the coolant media. Between 0.15 to 0.9 mm 3/mm.s of specific material removal rate, ground sur face temperature of mold insert was increased from 0.3 ℃ to 59.7 ℃ for chi lled air. For the similar grinding conditions with the coolant fluid an increase from 0.9 ℃ to 14.4 ℃ was recorded. With increase of specific material removal rate from 0.15 to 0.65 mm 3/mm.s, F t/F n ratio was increased from (0.2 to 0.4), (0.6 to 1.67) for wet coolant and chilled air respectively. Despite of high F t/F n ratio and ground surface temperature, chilled air method has shown a surface waviness, W t from (2 to 5.6) μm. Microstructure examination of chilled air produced ground surface was comparable to those of using coolant fluids. Surface finish, R a of (0.45～0.7) μm was achieved for mold insert . This work will enable to have clear understanding about the quantitative influe nce of chilled air as well as the clamping method against the surface waviness o f thin mold insert.
基金Project(2003AA302210)supported by the National Hi-tech Research Prograrm of Chinap.
文摘To evaluate the bioeompatibility of MIM 316L stainless steel,the percentage of S-period cells were detected by flow cytometry after L929 incubated with extraction of MIM 316L stainless steel,using titanium implant materials of clinical application as the contrast.Both materials were implanted in animal and the histopathological evaluations were carried out.The statistical analyses show that there are no significant differences between two groups(P>0.05),which demonstrates that MIM 316L stainless steel has a good biocompatibility.
文摘Obtaining the optimal values of the parameters for th e design of a required mould and the operation of the moulding process are diffi cult, this is due to the complexity of product geometry and the variation of pla stic material properties. The typical parameters for the mould design and mouldi ng process are melt flow length, injection pressure, holding pressure, back pres sure, injection speed, melt temperature, mould temperature, clamping force, inje ction time, holding time and cooling time. This paper discusses the difficulties of using the current computer aided optimization methods to acquire the values of the parameters. A method that is based on the concept of genetic algorithm is proposed to overcome the difficulties. The proposed method describes in details on how to attain the optimal values of the parameters form a given product geom etry.
文摘With the use of multimedia which combines the use o f text, sound, images, motion video and animation, it is more efficient for studen ts to learn mould design interactively. A program is created using several multi media software to simulate the mechanism of moulding processes in order to let s tudents understand the concept of mould design. In addition, students can even access the program through the Internet. Therefore, the software is defined as Multimedia and Internet Technology (MIT) program. The MIT program consists of four sections: (i) simulation of mould mechanisms, ( ii) cooling system, (iii) material information and (iv) games for tutorials. Sec tion One covers the basic operations of different types of moulds such as two-p late mould, three-plate mould, split mould, side-core mould and mould with und ercuts. Section Two introduces different types of cooling systems such as bubble r, baffle, cooling circuits, etc. Section Three provides some useful material in formation for mould design. Section Four contains games of matching mould compon ents, mould design problem finding and multiple choice questions to test student s how much they understand mould design concept. Multimedia is highly effective particularly in teaching and learning. It changes the nature of learning itself. It makes reading dynamic by giving words an impo rtant new dimension. It allows students to see, hear and do simultaneously, thus significantly reducing average learning time. Furthermore, through cooperative learning on Internet, students can access the program, share data or search info rmation anytime anywhere. Therefore, Multimedia and Internet Technology is one o f the vital aspects to speed up the realization of information age in society.
