The present study introduces a screw-pressing charging method to tackle deficiencies in automation and charge uniformity during the melt-casting of polymer-based energetic materials.To ensure the safety of the experim...The present study introduces a screw-pressing charging method to tackle deficiencies in automation and charge uniformity during the melt-casting of polymer-based energetic materials.To ensure the safety of the experiments,this study used inert materials with similar physical properties to partially substitute for the actual energetic components in the preparation of simulant materials.By thoroughly analyzing slurry physical properties,a simulation framework and an extensive performance evaluation method were developed.Such tools guide the design of the structure and configuration of process parameters.Results demonstrate that employing the Pin element significantly enhances radial mixing within the screw,minimizes temperature variations in the slurry,and improves both efficiency and safety in the mixing process.Further,adjustments such as widening the cone angle of the barrel,modifying the solid content of the slurry,and varying the speed of the screw can optimize the mechanical and thermal coupling in the flow field.These adjustments promote higher-quality slurry and create a safer production environment for the extrusion process.展开更多
Cobalt-free cathode materials are attractive for their high capacity and low cost,yet they still encounter issues with structural and surface instability.AlPO_(4),in particular,has garnered attention as an effective s...Cobalt-free cathode materials are attractive for their high capacity and low cost,yet they still encounter issues with structural and surface instability.AlPO_(4),in particular,has garnered attention as an effective stabilizer for bulk and surface.However,the impact of interfacial reactions and elemental interdiffusion between AlPO_(4) and LiNi_(0.95)Mn_(0.05)O_(2) upon sintering on the bulk and surface remains elusive.In this study,we demonstrate that during the heat treatment process,AlPO_(4) decomposes,resulting in Al doping into the bulk of the cathode through elemental interdiffusion.Simultaneously,PO_(4)^(3-)reacts with the surface Li of material to form a Li_3PO_(4) coating,inducing lithium deficiency,thereby increasing Li/Ni mixing.The suitable Li/Ni mixing,previously overlooked in AlPO_(4) modification,plays a pivotal role in stabilizing the bulk and surface,exceeding the synergy of Al doping and Li_3PO_(4) coating.The presence of Ni^(2+)ions in the lithium layers contributes to the stabilization of the delithiated structure via a structural pillar effect.Moreover,suitable Li/Ni mixing can stabilize the lattice oxygen and electrode-electrolyte interface by increasing oxygen removal energy and reducing the overlap between the Ni^(3+/4+)e_g and O^(2-)2p orbitals.These findings offer new perspectives for the design of stable cobalt-free cathode materials.展开更多
Co-free Li-rich layered oxides(LLOs)are emerging as promising cathode materials for Li-ion batteries due to their low cost and high capacity.However,they commonly face severe structural instability and poor electroche...Co-free Li-rich layered oxides(LLOs)are emerging as promising cathode materials for Li-ion batteries due to their low cost and high capacity.However,they commonly face severe structural instability and poor electrochemical activity,leading to diminished capacity and voltage performance.Herein,we introduce a Co-free LLO,Li_(1.167)Ni_(0.222)Mn_(0.611)O_(2)(Cf-L1),which features a cooperative structure of Li/Ni mixing and stacking faults.This structure regulates the crystal and electronic structures,resulting in a higher discharge capacity of 300.6 mA h g^(-1)and enhanced rate capability compared to the typical Co-free LLO,Li_(1.2)Ni_(0.2)Mn_(0.6)O_(2)(Cf-Ls).Density functional theory(DFT)indicates that Li/Ni mixing in LLOs leads to increased Li-O-Li configurations and higher anionic redox activities,while stacking faults further optimize the electronic interactions of transition metal(TM)3d and non-bonding O 2p orbitals.Moreover,stacking faults accommodate lattice strain,improving electrochemical reversibility during charge/discharge cycles,as demonstrated by the in situ XRD of Cf-L1 showing less lattice evolution than Cf-Ls.This study offers a structured approach to developing Co-free LLOs with enhanced capacity,voltage,rate capability,and cyclability,significantly impacting the advancement of the next-generation Li-ion batteries.展开更多
Li/Ni mixing negatively influences the discharge capacity of lithium nickel oxide and high-nickel ternary cathode materials.However,accurately measuring the Li/Ni mixing degree is difficult due to the preferred orient...Li/Ni mixing negatively influences the discharge capacity of lithium nickel oxide and high-nickel ternary cathode materials.However,accurately measuring the Li/Ni mixing degree is difficult due to the preferred orientation of labbased XRD measurements using Bragg–Brentano geometry.Here,we find that employing spherical harmonics in Rietveld refinement to eliminate the preferred orientation can significantly decrease the measurement error of the Li/Ni mixing ratio.The Li/Ni mixing ratio obtained from Rietveld refinement with spherical harmonics shows a strong correlation with discharge capacity,which means the electrochemical capacity of lithium nickel oxide and high-nickel ternary cathode can be estimated by the Li/Ni mixing degree.Our findings provide a simple and accurate method to estimate the Li/Ni mixing degree,which is valuable to the structural analysis and screening of the synthesis conditions of lithium nickel oxide and high-nickel ternary cathode materials.展开更多
Due to the spatial characteristics of orbital angular momentum,vortex fields can be applied in the fields of quantum storage and quantum information.We study the realization of spatially modulated vortex fields based ...Due to the spatial characteristics of orbital angular momentum,vortex fields can be applied in the fields of quantum storage and quantum information.We study the realization of spatially modulated vortex fields based on four-wave mixing in a four-level atomic system with a diamond structure.The intensity and spiral phase of the vortex field are effectively transferred to the generated four-wave mixing field.By changing the detuning of the probe field,the phase and intensity of the generated vertex four-wave mixing field can be changed.When the probe field takes a large detuning value,the spatial distribution of the intensity and phase of the vertex four-wave mixing field can be effectively tuned by adjusting the Rabi frequency or detuning value of the coupled field.At the same time,we also provide a detailed explanation based on the dispersion relationship,and the results agree well with our simulation results.展开更多
We study theoretically the electrical shot noise properties of tunnel junctions between a normal metal and a superconductor with the mixture of singlet s-wave and chiral triplet p-wave pairing due to broken inversion ...We study theoretically the electrical shot noise properties of tunnel junctions between a normal metal and a superconductor with the mixture of singlet s-wave and chiral triplet p-wave pairing due to broken inversion symmetry. We investigate how the shot noise properties vary as the relative amplitude between the two parity components in the pairing potential is changed. It is demonstrated that some characteristics of the electrical shot noise properties of such tunnel junctions may depend sensitively on the relative amplitude between the two parity components in the pairing potential, and some significant changes may occur in the electrical shot noise properties when the relative amplitude between the two parity components is varied from the singlet s-wave pairing dominated regime to the chiral triplet p-wave pairing dominated regime. In the chiral triplet p-wave pairing dominated regime, the ratio of noise power to electric current is close to 2e both in the in-gap and in the out-gap region. In the singlet s-wave pairing dominated regime, the value of this ratio is close to 4e in the inner gap region but may reduce to about 2e in the outer gap region as the relative amplitude of the chiral triplet pairing component is increased. The variations of the differential shot noise with the bias voltage also exhibit some significantly different features in different regimes. Such different features can serve as useful diagnostic tools for the determination of the relative magnitude of the two parity components in the pairing potential.展开更多
The flows of rigid polyvinyl chloride （R-PVC） in co-rotating twin screw extruders with screw mixing elements and regular screw elements were simulated by using the finite element method. The three-dimensional, non-i...The flows of rigid polyvinyl chloride （R-PVC） in co-rotating twin screw extruders with screw mixing elements and regular screw elements were simulated by using the finite element method. The three-dimensional, non-isothermal flow fields of R-PVC in the two kinds of screw elements were calculated. The mixing performance of each type of element was studied by the particle tracking analysis method. The results show that the temperature distribution and shear-rate distribution are more uniform in the flow channel with screw mixing elements than in the flow channel with regular screw elements. Screw mixing elements provide better distributive and dispersive mixing performance but worse conveying capacity than regular screw elements.展开更多
We have investigated the dressed effects of non-degenerate four-wave mixing （NDFWM） and demonstrated a phase-sensitive method of studying the fifth-order nonlinear susceptibility due to atomic coherence in RN-type f...We have investigated the dressed effects of non-degenerate four-wave mixing （NDFWM） and demonstrated a phase-sensitive method of studying the fifth-order nonlinear susceptibility due to atomic coherence in RN-type four-level system. In the presence of a strong coupling field, NDFWM spectrum exhibits Autler-Townes splitting, accompanied by either suppression or enhancement of the NDFWM signal, which is directly related to the competition between the absorption and dispersion contributions. The heterodyne-deteeted nonlinear absorption and dispersion of six-wave mixing signal in the RN-type system show that the hybrid radiation-matter detuning damping oscillation is in the THz range and can be controlled and modified through the eolour-locked correlation of twin noisy fields.展开更多
In this paper, we give some conditions on diverging rate of series of the probabilities and converging rate of series of the α-mixing coefficients for sequences of events, under which the conclusion of the Second Bor...In this paper, we give some conditions on diverging rate of series of the probabilities and converging rate of series of the α-mixing coefficients for sequences of events, under which the conclusion of the Second Borel-Cantelli Lemma holds. As corollaries, some moment conditions are obtained, under which the strong law of large numbers holds for sequences of identically distributed random variables.展开更多
Water-rock interaction and groundwater mixing are important phenomena in understanding hydrogeological systems and the stability of rock slopes especially those consisting largely of moderately watersoluble minerals l...Water-rock interaction and groundwater mixing are important phenomena in understanding hydrogeological systems and the stability of rock slopes especially those consisting largely of moderately watersoluble minerals like calcite. In this study, the hydrogeological and geochemical evolutions of groundwater in a limestone quarry composed of three strata: limestone layer(covering), interbedded layer under the covering layer, and slaty greenstone layer(basement) were investigated. Water-rock interaction in the open-pit limestone quarry was evaluated using PHREEQC, while hierarchical cluster analysis(HCA)and principal component analysis(PCA) were used to classify and identify water sources responsible for possible groundwater mixing within rock layers. In addition, Geochemist's Workbench was applied to estimate the mixing fractions to clarify sensitive zones that may affect rock slope stability. The results showed that the changes in Ca2+and HCO3àconcentrations of several groundwater samples along the interbedded layer could be attributed to mixing groundwater from the limestone layer and that from slaty greenstone layer. Based on the HCA and PCA results, groundwaters were classified into several types depending on their origin:(1) groundwater from the limestone layer(LO),(2) mixed groundwater flowing along the interbedded layer(e.g., groundwater samples L-7, L-11, S-3 and S-4), and(3) groundwater originating from the slaty greenstone layer(SO). The mixing fractions of 41% LO: 59% SO, 64% LO: 36% SO, 43%LO: 57% SOand 25% LO: 75% SOon the normal days corresponded to groundwaters L-7, L-11, S-3 and S-4,respectively, while the mixing fractions of groundwaters L-7 and L-11(61% LO: 39% SOand 93% LO: 7% SO,respectively) on rainy days became the majority of groundwater originating from the limestone layer.These indicate that groundwater along the interbedded layer significantly affected the stability of rock slopes by enlarging multi-breaking zones in the layer through calcite dissolution and inducing high water pressure, tension cracks and potential sliding plane along this layer particularly during intense rainfall episodes.展开更多
Based on multi-fluid volume fraction and piecewise parabolic method （PPM）, a multi-viscosity-fluid hydrodynamic code MVPPM （Multi-Viscosity-Fluid Piecewise Parabolic Method） is developed and applied to the problem...Based on multi-fluid volume fraction and piecewise parabolic method （PPM）, a multi-viscosity-fluid hydrodynamic code MVPPM （Multi-Viscosity-Fluid Piecewise Parabolic Method） is developed and applied to the problems of shock-induced hydrodynamic interfacial instability and mixing. Simulations of gas/liquid interface instability show that the influences of initial perturbations on the fluid mixing zone （FMZ） growth are significant, especially at the late stages, while grids have only a slight effect on the FMZ width, when the interface is impulsively accelerated by a shock wave passing through it. A numerical study of the hydrodynamic interfacial instability and mixing of gaseous flows impacted by re-shocks is presented. It reveals that the numerical results are in good agreement with the experimental results and the mixing growth rate strongly depends on initial conditions. Ultimately, the jelly layer experiment relevant to the instability impacted by exploding is simulated. The shape of jelly interface, position of front face of jelly layer, crest and trough of perturbation versus time are given; their simulated results are in good agreement with experimental results.展开更多
Functional traits of trees are significantly associated with their adaptation strategies and productivity.However,the effects of species composition and mixing proportion on the functional traits of trees grown in mix...Functional traits of trees are significantly associated with their adaptation strategies and productivity.However,the effects of species composition and mixing proportion on the functional traits of trees grown in mixed plantations have not been studied extensively.In this study,planting experiments(duration about seven months)were used to study variations in functional traits and biomass allocation of C unninghamia lanceolata(Lamb.)Hook and Phoebe bournei(Hemsley)Yang seedlings in five different mixes(0C:4P,1C:3P,1C:1P,3C:1P,and 4C:0P).Total leaf area per seedling increased in each species as its respective proportion in the mixture decreased.However,the specific leaf area decreased for P.bournei under low percent composition,and the specific leaf area for C.lanceolata differed only marginally among the plantings.The net photosynthetic rates of the two species were higher in the mixed plantings than in their corresponding monocultures,whereas the transpiration rate,stomatal conductance,and instantaneous water use efficiency were not different among the plantings.The average root length and root surface area of C.lanceolata and P.bournei were higher in the mixed plantings than in their monocultures.Specifically,root surface area of C.lanceolate and both root length and surface area of P.bournei increased significantly in the 1C:3P and 2C:2P mixed plantings.Leaf,stem,root,and total dry mass per seedling for C.lanceolata decreased with its increasing percent composition in the mixed plantings,while these variables varied less for P.bournei.The plasticity of biomass allocation was relatively low for both species.Total biomass per planting was higher in the mixed plantings than in the monocultures.Our study indicates that species composition and mixing proportion can considerably affect the functional traits of C.lanceolata and P.bournei.The increase in productivity in the mixed plantings may be partially attributed to low rates of competition between the two species,and future studies should examine the different interspecies relationships.The results of this study can be used to improve plantation productivity and ultimately increase the sustainability of tree products and help to better understand the adaptation strategies of plant coexistence.展开更多
This paper presents a three-dimensional, three-phase compositional model considering CO2 phase equilibrium between water and oil. In this model, CO2 is mutually soluble in aqueous and hydrocarbon phases, while other c...This paper presents a three-dimensional, three-phase compositional model considering CO2 phase equilibrium between water and oil. In this model, CO2 is mutually soluble in aqueous and hydrocarbon phases, while other components, except water,exist in hydrocarbon phase. The Peng–Robinson(PR) equation of state and the Wong–Sandler mixing rule with non-random two-liquid parameters are used to calculate CO2 fugacity in the aqueous phase. One-dimensional and three-dimensional CO2 flooding examples show that a significant amount of injected CO2 is dissolved in water. Our simulation shows 7% of injected CO2 can be dissolved in the aqueous phase, which delays oil recovery by 4%. The gas rate predicted by the model is smaller than the conventional model as long as water is undersaturated by CO2, which can be considered as 'lost' in the aqueous phase. The model also predicts that the delayed oil can be recovered after the gas breakthrough, indicating that delayed oil is hard to recover in field applications. A three-dimensional example reveals that a highly stratified reservoir causes uneven displacement and serious CO2 breakthrough. If mobility control measures like water alternating gas are undertaken, the solubility e ects will be more pronounced than this example.展开更多
For studying the mixing tank for RMAC (residue upgrading to maximize asphaltene conversion) reactor, the CFD simulation was employed to simulate the flow field in the mixing tank. The dispersion of liquid-liquid phase...For studying the mixing tank for RMAC (residue upgrading to maximize asphaltene conversion) reactor, the CFD simulation was employed to simulate the flow field in the mixing tank. The dispersion of liquid-liquid phase in the mixing tank and the power of turbines were investigated. The simulation results showed that compared with the original doublelayer propeller, the A310-swept double-layer impellers could reduce the liquid heterogeneous degree by 27.5% and the stirring power by 3.25%. The influence of rotation speed on the heterogeneous degree and stirring power was investigated, and the critical rotation speed was obtained. The optimal rotation speed was determined to be 240 r/min. The heterogeneous degree was 0.19 and the minimum stirring power was 10.89 W. By optimizing the impeller selection and process conditions, the overall performance of the mixing tank could be significantly improved.展开更多
In this study, a computer code is developed to numerically investigate a magnetic bead micromixer under different conditions. The micromixer consists of a microchannel and numerous micro magnetic particles which enter...In this study, a computer code is developed to numerically investigate a magnetic bead micromixer under different conditions. The micromixer consists of a microchannel and numerous micro magnetic particles which enter the micromixer by fluid flows and are actuated by an alternating magnetic field normal to the main flow. An important feature of micromixer which is not considered before by researchers is the particle entrance arrangement into the micromixer. This parameter could effectively affect the micromixer efficiency. There are two general micro magnetic particle entrance arrangements in magnetic bead micromixers: determined position entrance and random position entrance. In the case of determined position entrances, micro magnetic particles enter the micromixer at specific positions of entrance cross section. However, in a random position entrance,particles enter the microchannel with no order. In this study mixing efficiencies of identical magnetic bead micromixers which only differ in particle entrance arrangement are numerically investigated and compared.The results reported in this paper illustrate that the prepared computer code can be one of the most powerful and beneficial tools for the magnetic bead micromixer performance analysis. In addition, the results show that some features of the magnetic bead micromixer are strongly affected by the entrance arrangement of the particles.展开更多
Stochastic resonance（SR） is studied in an under-damped bistable system driven by the harmonic mixing signal and Gaussian white noise. Using the linear response theory（LRT）, the expressions of the spectral amplific...Stochastic resonance（SR） is studied in an under-damped bistable system driven by the harmonic mixing signal and Gaussian white noise. Using the linear response theory（LRT）, the expressions of the spectral amplification at fundamental and higher-order harmonic are obtained. The effects of damping coefficient, noise intensity, signal amplitude, and frequency on spectral amplifications are explored. Meanwhile, the power spectral density（PSD） and signal-to-noise ratio（SNR） are calculated to quantify SR and verify the theoretical results. The SNRs at the first and second harmonics exhibit a minimum first and a maximum later with increasing noise intensity. That is, both of the noise-induced suppression and resonance can be observed by choosing proper system parameters. Especially, when the ratio of the second harmonic amplitude to the fundamental one takes a large value, the SNR at the fundamental harmonic is a monotonic function of noise intensity and the SR phenomenon disappears.展开更多
High-performance lithium-ion batteries(LIB)are important in powering emerging technologies.Cathodes are regarded as the bottleneck of increasing battery energy density,among which layered oxides are the most promising...High-performance lithium-ion batteries(LIB)are important in powering emerging technologies.Cathodes are regarded as the bottleneck of increasing battery energy density,among which layered oxides are the most promising candidates for LIB.However,a limitation with layered oxides cathodes is the transition metal and Li site mixing,which significantly impacts battery capacity and cycling stability.Despite recent research on Li/Ni mixing,there is a lack of comprehensive understanding of the origin of cation mixing between the transition metal and Li;therefore,practical means to address it.Here,a critical review of cation mixing in layered cathodes has been provided,emphasising the understanding of cation mixing mechanisms and their impact on cathode material design.We list and compare advanced characterisation techniques to detect cation mixing in the material structure;examine methods to regulate the degree of cation mixing in layered oxides to boost battery capacity and cycling performance,and critically assess how these can be applied practically.An appraisal of future research directions,including superexchange interaction to stabilise structures and boost capacity retention has also been concluded.Findings will be of immediate benefit in the design of layered cathodes for high-performance rechargeable LIB and,therefore,of interest to researchers and manufacturers.展开更多
This paper presents a theoretical study of wavelength dependence four-wave-mixing （FWM） spectroscopy in a micrometric thin atomic vapour. It compares three cases termed as mismatched case I, matched case and mismatc...This paper presents a theoretical study of wavelength dependence four-wave-mixing （FWM） spectroscopy in a micrometric thin atomic vapour. It compares three cases termed as mismatched case I, matched case and mismatched case II for the probe wavelength less, equal and greater than the pump wavelength respectively. It finds that Dicke- narrowing can overcome width broadening induced by Doppler effects and polarisation interference of thermal atoms, and high resolution FWM spectra can be achieved both in matched and mismatched wavelength for many cases. It also finds that the magnitude of the FWM signal can be dramatically modified to be suppressed or to be enhanced in comparison with that of matched wavelength in mismatched case I or II. The width narrowing and the magnitude suppression or enhancement can be demonstrated by considering enhanced contribution of slow atoms induced by atom-wall collision and transient effect of atom-light interaction in a micrometric thin vapour.展开更多
In order to obtain high-quality spherical RDX crystal particles,the RDX crystals were suspended in a mixed solvent of cyclohexanone and cyclohexane,subsequently a solvent etching study was carried out under the action...In order to obtain high-quality spherical RDX crystal particles,the RDX crystals were suspended in a mixed solvent of cyclohexanone and cyclohexane,subsequently a solvent etching study was carried out under the action of vibration/acoustic flow coupled flow field,which generated by resonance acoustic mixing.The effects of solvent ratio,temperature,acceleration and experiment time on morphology as well as particle size of RDX crystals were studied.Not only were the morphology,particle size distribution and crystal form of RDX crystals determined,but also the thermal decomposition performance and mechanical sensitivity of spherical RDX were examined and discussed.Results indicated that under the process of solvent/non-solvent volume ratio at 1:2,temperature of 40℃,acceleration of 40 g and experiment time of 4 h,α-type RDX crystal with sphericity of 0.92 can be obtained.Furthermore,the median particle size(D_(50))of spherical RDX crystals is 215.8 μm with a unimodal particle size distribution(size span 1.34).For one thing,the thermal decomposition peak temperature of spherical RDX is about 2.5℃ higher than that of raw RDX,and apparent activation energy reaches 444.68 kJ/mol.For another thing,impact sensitivity and friction sensitivity of spherical RDX are 18.18% and 33.33% lower than that of raw RDX,respectively.It demonstrates that safety of spherical RDX under thermal,impact and friction stimuli has been improved.展开更多
The influence of degenerate four-wave mixing （FWM） on the performance of supercontinuum-based multiwavelength optical source has been investigated in detail experimentally and theoretically. Numerical simulation res...The influence of degenerate four-wave mixing （FWM） on the performance of supercontinuum-based multiwavelength optical source has been investigated in detail experimentally and theoretically. Numerical simulation results show that the degenerate FWM effect has a deteriorative influence on the spectral uniformity and the optical signal-to-noise ratio （OSNR） of supercontinuum-based optical source, and by suppressing degenerate FWM effect the performance enhancement of the supercontinuum can be achieved successfully. These results are also confirmed by our experiments. Experimentally, by suppressing degenerate FWM the crosstalk of adjacent channels to the filtered channel can be reduced by as much as 15 dB, and consequently the measured receiver sensitivity at 10 Gbit/s for the filtered optical source is improved from -1.7 to -17.8 dBm.展开更多
基金financially supported by the Fundamental Research Funds for the Central Universities(Grant No.30923011018)。
文摘The present study introduces a screw-pressing charging method to tackle deficiencies in automation and charge uniformity during the melt-casting of polymer-based energetic materials.To ensure the safety of the experiments,this study used inert materials with similar physical properties to partially substitute for the actual energetic components in the preparation of simulant materials.By thoroughly analyzing slurry physical properties,a simulation framework and an extensive performance evaluation method were developed.Such tools guide the design of the structure and configuration of process parameters.Results demonstrate that employing the Pin element significantly enhances radial mixing within the screw,minimizes temperature variations in the slurry,and improves both efficiency and safety in the mixing process.Further,adjustments such as widening the cone angle of the barrel,modifying the solid content of the slurry,and varying the speed of the screw can optimize the mechanical and thermal coupling in the flow field.These adjustments promote higher-quality slurry and create a safer production environment for the extrusion process.
基金financial support from the Natural Science Foundation of Shandong Province (ZR2022QB140)the PhD Initiation Program of Liaocheng University (318052138)the Natural Science Foundation of Shandong Province (ZR2023MB002 and ZR2021MB114)。
文摘Cobalt-free cathode materials are attractive for their high capacity and low cost,yet they still encounter issues with structural and surface instability.AlPO_(4),in particular,has garnered attention as an effective stabilizer for bulk and surface.However,the impact of interfacial reactions and elemental interdiffusion between AlPO_(4) and LiNi_(0.95)Mn_(0.05)O_(2) upon sintering on the bulk and surface remains elusive.In this study,we demonstrate that during the heat treatment process,AlPO_(4) decomposes,resulting in Al doping into the bulk of the cathode through elemental interdiffusion.Simultaneously,PO_(4)^(3-)reacts with the surface Li of material to form a Li_3PO_(4) coating,inducing lithium deficiency,thereby increasing Li/Ni mixing.The suitable Li/Ni mixing,previously overlooked in AlPO_(4) modification,plays a pivotal role in stabilizing the bulk and surface,exceeding the synergy of Al doping and Li_3PO_(4) coating.The presence of Ni^(2+)ions in the lithium layers contributes to the stabilization of the delithiated structure via a structural pillar effect.Moreover,suitable Li/Ni mixing can stabilize the lattice oxygen and electrode-electrolyte interface by increasing oxygen removal energy and reducing the overlap between the Ni^(3+/4+)e_g and O^(2-)2p orbitals.These findings offer new perspectives for the design of stable cobalt-free cathode materials.
基金financially supported by the National Natural Science Foundation of China(52202046,51602246,and 51801144)the Natural Science Foundation of Shanxi Provincial(2021JQ-034)。
文摘Co-free Li-rich layered oxides(LLOs)are emerging as promising cathode materials for Li-ion batteries due to their low cost and high capacity.However,they commonly face severe structural instability and poor electrochemical activity,leading to diminished capacity and voltage performance.Herein,we introduce a Co-free LLO,Li_(1.167)Ni_(0.222)Mn_(0.611)O_(2)(Cf-L1),which features a cooperative structure of Li/Ni mixing and stacking faults.This structure regulates the crystal and electronic structures,resulting in a higher discharge capacity of 300.6 mA h g^(-1)and enhanced rate capability compared to the typical Co-free LLO,Li_(1.2)Ni_(0.2)Mn_(0.6)O_(2)(Cf-Ls).Density functional theory(DFT)indicates that Li/Ni mixing in LLOs leads to increased Li-O-Li configurations and higher anionic redox activities,while stacking faults further optimize the electronic interactions of transition metal(TM)3d and non-bonding O 2p orbitals.Moreover,stacking faults accommodate lattice strain,improving electrochemical reversibility during charge/discharge cycles,as demonstrated by the in situ XRD of Cf-L1 showing less lattice evolution than Cf-Ls.This study offers a structured approach to developing Co-free LLOs with enhanced capacity,voltage,rate capability,and cyclability,significantly impacting the advancement of the next-generation Li-ion batteries.
基金Project supported by the Natural Science Foundation of Beijing(Grant No.Z200013)the Beijing Municipal Science&Technology(Grant No.Z191100004719001)the National Natural Science Foundation of China(Grant Nos.52325207 and 22005333)。
文摘Li/Ni mixing negatively influences the discharge capacity of lithium nickel oxide and high-nickel ternary cathode materials.However,accurately measuring the Li/Ni mixing degree is difficult due to the preferred orientation of labbased XRD measurements using Bragg–Brentano geometry.Here,we find that employing spherical harmonics in Rietveld refinement to eliminate the preferred orientation can significantly decrease the measurement error of the Li/Ni mixing ratio.The Li/Ni mixing ratio obtained from Rietveld refinement with spherical harmonics shows a strong correlation with discharge capacity,which means the electrochemical capacity of lithium nickel oxide and high-nickel ternary cathode can be estimated by the Li/Ni mixing degree.Our findings provide a simple and accurate method to estimate the Li/Ni mixing degree,which is valuable to the structural analysis and screening of the synthesis conditions of lithium nickel oxide and high-nickel ternary cathode materials.
基金Project supported by the National Natural Science Foundation of China (Grant Nos.11704151 and 11247201)the Twelfth Five-year Program for Science and Technology of Education Department of Jilin Province (Grant No.20150215)。
文摘Due to the spatial characteristics of orbital angular momentum,vortex fields can be applied in the fields of quantum storage and quantum information.We study the realization of spatially modulated vortex fields based on four-wave mixing in a four-level atomic system with a diamond structure.The intensity and spiral phase of the vortex field are effectively transferred to the generated four-wave mixing field.By changing the detuning of the probe field,the phase and intensity of the generated vertex four-wave mixing field can be changed.When the probe field takes a large detuning value,the spatial distribution of the intensity and phase of the vertex four-wave mixing field can be effectively tuned by adjusting the Rabi frequency or detuning value of the coupled field.At the same time,we also provide a detailed explanation based on the dispersion relationship,and the results agree well with our simulation results.
文摘We study theoretically the electrical shot noise properties of tunnel junctions between a normal metal and a superconductor with the mixture of singlet s-wave and chiral triplet p-wave pairing due to broken inversion symmetry. We investigate how the shot noise properties vary as the relative amplitude between the two parity components in the pairing potential is changed. It is demonstrated that some characteristics of the electrical shot noise properties of such tunnel junctions may depend sensitively on the relative amplitude between the two parity components in the pairing potential, and some significant changes may occur in the electrical shot noise properties when the relative amplitude between the two parity components is varied from the singlet s-wave pairing dominated regime to the chiral triplet p-wave pairing dominated regime. In the chiral triplet p-wave pairing dominated regime, the ratio of noise power to electric current is close to 2e both in the in-gap and in the out-gap region. In the singlet s-wave pairing dominated regime, the value of this ratio is close to 4e in the inner gap region but may reduce to about 2e in the outer gap region as the relative amplitude of the chiral triplet pairing component is increased. The variations of the differential shot noise with the bias voltage also exhibit some significantly different features in different regimes. Such different features can serve as useful diagnostic tools for the determination of the relative magnitude of the two parity components in the pairing potential.
文摘The flows of rigid polyvinyl chloride （R-PVC） in co-rotating twin screw extruders with screw mixing elements and regular screw elements were simulated by using the finite element method. The three-dimensional, non-isothermal flow fields of R-PVC in the two kinds of screw elements were calculated. The mixing performance of each type of element was studied by the particle tracking analysis method. The results show that the temperature distribution and shear-rate distribution are more uniform in the flow channel with screw mixing elements than in the flow channel with regular screw elements. Screw mixing elements provide better distributive and dispersive mixing performance but worse conveying capacity than regular screw elements.
基金Project supported by the National Natural Science Foundation of China （Grant Nos 60308002 and 60678005）, the Foundation for the Author of National Excellent Doctoral Dissertation of China （Grant No 200339）, the Research Foundation from Ministry of Education of China （Grant No 105156）, the For Ying-Tong Education Foundation for Young Teachers of Higher Education Institutions of China （Grant No 101061） and the Specialized Research Fund for the Doctoral Program of Higher Education of China （Grant No 20050698017）.
文摘We have investigated the dressed effects of non-degenerate four-wave mixing （NDFWM） and demonstrated a phase-sensitive method of studying the fifth-order nonlinear susceptibility due to atomic coherence in RN-type four-level system. In the presence of a strong coupling field, NDFWM spectrum exhibits Autler-Townes splitting, accompanied by either suppression or enhancement of the NDFWM signal, which is directly related to the competition between the absorption and dispersion contributions. The heterodyne-deteeted nonlinear absorption and dispersion of six-wave mixing signal in the RN-type system show that the hybrid radiation-matter detuning damping oscillation is in the THz range and can be controlled and modified through the eolour-locked correlation of twin noisy fields.
基金Supported by the SCR of Chongqing Municipal Education Commission(KJ090703)
文摘In this paper, we give some conditions on diverging rate of series of the probabilities and converging rate of series of the α-mixing coefficients for sequences of events, under which the conclusion of the Second Borel-Cantelli Lemma holds. As corollaries, some moment conditions are obtained, under which the strong law of large numbers holds for sequences of identically distributed random variables.
文摘Water-rock interaction and groundwater mixing are important phenomena in understanding hydrogeological systems and the stability of rock slopes especially those consisting largely of moderately watersoluble minerals like calcite. In this study, the hydrogeological and geochemical evolutions of groundwater in a limestone quarry composed of three strata: limestone layer(covering), interbedded layer under the covering layer, and slaty greenstone layer(basement) were investigated. Water-rock interaction in the open-pit limestone quarry was evaluated using PHREEQC, while hierarchical cluster analysis(HCA)and principal component analysis(PCA) were used to classify and identify water sources responsible for possible groundwater mixing within rock layers. In addition, Geochemist's Workbench was applied to estimate the mixing fractions to clarify sensitive zones that may affect rock slope stability. The results showed that the changes in Ca2+and HCO3àconcentrations of several groundwater samples along the interbedded layer could be attributed to mixing groundwater from the limestone layer and that from slaty greenstone layer. Based on the HCA and PCA results, groundwaters were classified into several types depending on their origin:(1) groundwater from the limestone layer(LO),(2) mixed groundwater flowing along the interbedded layer(e.g., groundwater samples L-7, L-11, S-3 and S-4), and(3) groundwater originating from the slaty greenstone layer(SO). The mixing fractions of 41% LO: 59% SO, 64% LO: 36% SO, 43%LO: 57% SOand 25% LO: 75% SOon the normal days corresponded to groundwaters L-7, L-11, S-3 and S-4,respectively, while the mixing fractions of groundwaters L-7 and L-11(61% LO: 39% SOand 93% LO: 7% SO,respectively) on rainy days became the majority of groundwater originating from the limestone layer.These indicate that groundwater along the interbedded layer significantly affected the stability of rock slopes by enlarging multi-breaking zones in the layer through calcite dissolution and inducing high water pressure, tension cracks and potential sliding plane along this layer particularly during intense rainfall episodes.
基金supported by the National Natural Science Foundation of China (Grant Nos 10672151 and 10772166)the Foundation of China Academy of Engineering Physics (Grant No 2008B0202011)the Fundamental Quality and Reliability of National Defence Science and Technology Industry of China
文摘Based on multi-fluid volume fraction and piecewise parabolic method （PPM）, a multi-viscosity-fluid hydrodynamic code MVPPM （Multi-Viscosity-Fluid Piecewise Parabolic Method） is developed and applied to the problems of shock-induced hydrodynamic interfacial instability and mixing. Simulations of gas/liquid interface instability show that the influences of initial perturbations on the fluid mixing zone （FMZ） growth are significant, especially at the late stages, while grids have only a slight effect on the FMZ width, when the interface is impulsively accelerated by a shock wave passing through it. A numerical study of the hydrodynamic interfacial instability and mixing of gaseous flows impacted by re-shocks is presented. It reveals that the numerical results are in good agreement with the experimental results and the mixing growth rate strongly depends on initial conditions. Ultimately, the jelly layer experiment relevant to the instability impacted by exploding is simulated. The shape of jelly interface, position of front face of jelly layer, crest and trough of perturbation versus time are given; their simulated results are in good agreement with experimental results.
基金supported by the Project of Public Welfare Technology Research in Zhejiang Province(LGN21C160010)the National Key Research and Development Program of China(No.2017YF C0505502)。
文摘Functional traits of trees are significantly associated with their adaptation strategies and productivity.However,the effects of species composition and mixing proportion on the functional traits of trees grown in mixed plantations have not been studied extensively.In this study,planting experiments(duration about seven months)were used to study variations in functional traits and biomass allocation of C unninghamia lanceolata(Lamb.)Hook and Phoebe bournei(Hemsley)Yang seedlings in five different mixes(0C:4P,1C:3P,1C:1P,3C:1P,and 4C:0P).Total leaf area per seedling increased in each species as its respective proportion in the mixture decreased.However,the specific leaf area decreased for P.bournei under low percent composition,and the specific leaf area for C.lanceolata differed only marginally among the plantings.The net photosynthetic rates of the two species were higher in the mixed plantings than in their corresponding monocultures,whereas the transpiration rate,stomatal conductance,and instantaneous water use efficiency were not different among the plantings.The average root length and root surface area of C.lanceolata and P.bournei were higher in the mixed plantings than in their monocultures.Specifically,root surface area of C.lanceolate and both root length and surface area of P.bournei increased significantly in the 1C:3P and 2C:2P mixed plantings.Leaf,stem,root,and total dry mass per seedling for C.lanceolata decreased with its increasing percent composition in the mixed plantings,while these variables varied less for P.bournei.The plasticity of biomass allocation was relatively low for both species.Total biomass per planting was higher in the mixed plantings than in the monocultures.Our study indicates that species composition and mixing proportion can considerably affect the functional traits of C.lanceolata and P.bournei.The increase in productivity in the mixed plantings may be partially attributed to low rates of competition between the two species,and future studies should examine the different interspecies relationships.The results of this study can be used to improve plantation productivity and ultimately increase the sustainability of tree products and help to better understand the adaptation strategies of plant coexistence.
基金financially supported by National Natural Science Foundation of China(U1762101)National Science and Technology Major Projects(2017ZX05069)
文摘This paper presents a three-dimensional, three-phase compositional model considering CO2 phase equilibrium between water and oil. In this model, CO2 is mutually soluble in aqueous and hydrocarbon phases, while other components, except water,exist in hydrocarbon phase. The Peng–Robinson(PR) equation of state and the Wong–Sandler mixing rule with non-random two-liquid parameters are used to calculate CO2 fugacity in the aqueous phase. One-dimensional and three-dimensional CO2 flooding examples show that a significant amount of injected CO2 is dissolved in water. Our simulation shows 7% of injected CO2 can be dissolved in the aqueous phase, which delays oil recovery by 4%. The gas rate predicted by the model is smaller than the conventional model as long as water is undersaturated by CO2, which can be considered as 'lost' in the aqueous phase. The model also predicts that the delayed oil can be recovered after the gas breakthrough, indicating that delayed oil is hard to recover in field applications. A three-dimensional example reveals that a highly stratified reservoir causes uneven displacement and serious CO2 breakthrough. If mobility control measures like water alternating gas are undertaken, the solubility e ects will be more pronounced than this example.
基金supported by the Major Science and Technology Project of SINOPEC (ST18012-4)
文摘For studying the mixing tank for RMAC (residue upgrading to maximize asphaltene conversion) reactor, the CFD simulation was employed to simulate the flow field in the mixing tank. The dispersion of liquid-liquid phase in the mixing tank and the power of turbines were investigated. The simulation results showed that compared with the original doublelayer propeller, the A310-swept double-layer impellers could reduce the liquid heterogeneous degree by 27.5% and the stirring power by 3.25%. The influence of rotation speed on the heterogeneous degree and stirring power was investigated, and the critical rotation speed was obtained. The optimal rotation speed was determined to be 240 r/min. The heterogeneous degree was 0.19 and the minimum stirring power was 10.89 W. By optimizing the impeller selection and process conditions, the overall performance of the mixing tank could be significantly improved.
文摘In this study, a computer code is developed to numerically investigate a magnetic bead micromixer under different conditions. The micromixer consists of a microchannel and numerous micro magnetic particles which enter the micromixer by fluid flows and are actuated by an alternating magnetic field normal to the main flow. An important feature of micromixer which is not considered before by researchers is the particle entrance arrangement into the micromixer. This parameter could effectively affect the micromixer efficiency. There are two general micro magnetic particle entrance arrangements in magnetic bead micromixers: determined position entrance and random position entrance. In the case of determined position entrances, micro magnetic particles enter the micromixer at specific positions of entrance cross section. However, in a random position entrance,particles enter the microchannel with no order. In this study mixing efficiencies of identical magnetic bead micromixers which only differ in particle entrance arrangement are numerically investigated and compared.The results reported in this paper illustrate that the prepared computer code can be one of the most powerful and beneficial tools for the magnetic bead micromixer performance analysis. In addition, the results show that some features of the magnetic bead micromixer are strongly affected by the entrance arrangement of the particles.
基金Project supported by the National Natural Science Foundation of China(Grant No.11772048)
文摘Stochastic resonance（SR） is studied in an under-damped bistable system driven by the harmonic mixing signal and Gaussian white noise. Using the linear response theory（LRT）, the expressions of the spectral amplification at fundamental and higher-order harmonic are obtained. The effects of damping coefficient, noise intensity, signal amplitude, and frequency on spectral amplifications are explored. Meanwhile, the power spectral density（PSD） and signal-to-noise ratio（SNR） are calculated to quantify SR and verify the theoretical results. The SNRs at the first and second harmonics exhibit a minimum first and a maximum later with increasing noise intensity. That is, both of the noise-induced suppression and resonance can be observed by choosing proper system parameters. Especially, when the ratio of the second harmonic amplitude to the fundamental one takes a large value, the SNR at the fundamental harmonic is a monotonic function of noise intensity and the SR phenomenon disappears.
基金the Australian Institute of Nuclear Science and Engineering (AINSE) Limited for providing financial assistance in the form of a Post Graduate Research Award (PGRA) to carry out this worksupported by the Australian Research Council under grants DP200101862, DP210101486, and FL210100050
文摘High-performance lithium-ion batteries(LIB)are important in powering emerging technologies.Cathodes are regarded as the bottleneck of increasing battery energy density,among which layered oxides are the most promising candidates for LIB.However,a limitation with layered oxides cathodes is the transition metal and Li site mixing,which significantly impacts battery capacity and cycling stability.Despite recent research on Li/Ni mixing,there is a lack of comprehensive understanding of the origin of cation mixing between the transition metal and Li;therefore,practical means to address it.Here,a critical review of cation mixing in layered cathodes has been provided,emphasising the understanding of cation mixing mechanisms and their impact on cathode material design.We list and compare advanced characterisation techniques to detect cation mixing in the material structure;examine methods to regulate the degree of cation mixing in layered oxides to boost battery capacity and cycling performance,and critically assess how these can be applied practically.An appraisal of future research directions,including superexchange interaction to stabilise structures and boost capacity retention has also been concluded.Findings will be of immediate benefit in the design of layered cathodes for high-performance rechargeable LIB and,therefore,of interest to researchers and manufacturers.
基金supported from the Major Program of Science Foundation of Xi’an University of Arts and Science
文摘This paper presents a theoretical study of wavelength dependence four-wave-mixing （FWM） spectroscopy in a micrometric thin atomic vapour. It compares three cases termed as mismatched case I, matched case and mismatched case II for the probe wavelength less, equal and greater than the pump wavelength respectively. It finds that Dicke- narrowing can overcome width broadening induced by Doppler effects and polarisation interference of thermal atoms, and high resolution FWM spectra can be achieved both in matched and mismatched wavelength for many cases. It also finds that the magnitude of the FWM signal can be dramatically modified to be suppressed or to be enhanced in comparison with that of matched wavelength in mismatched case I or II. The width narrowing and the magnitude suppression or enhancement can be demonstrated by considering enhanced contribution of slow atoms induced by atom-wall collision and transient effect of atom-light interaction in a micrometric thin vapour.
文摘In order to obtain high-quality spherical RDX crystal particles,the RDX crystals were suspended in a mixed solvent of cyclohexanone and cyclohexane,subsequently a solvent etching study was carried out under the action of vibration/acoustic flow coupled flow field,which generated by resonance acoustic mixing.The effects of solvent ratio,temperature,acceleration and experiment time on morphology as well as particle size of RDX crystals were studied.Not only were the morphology,particle size distribution and crystal form of RDX crystals determined,but also the thermal decomposition performance and mechanical sensitivity of spherical RDX were examined and discussed.Results indicated that under the process of solvent/non-solvent volume ratio at 1:2,temperature of 40℃,acceleration of 40 g and experiment time of 4 h,α-type RDX crystal with sphericity of 0.92 can be obtained.Furthermore,the median particle size(D_(50))of spherical RDX crystals is 215.8 μm with a unimodal particle size distribution(size span 1.34).For one thing,the thermal decomposition peak temperature of spherical RDX is about 2.5℃ higher than that of raw RDX,and apparent activation energy reaches 444.68 kJ/mol.For another thing,impact sensitivity and friction sensitivity of spherical RDX are 18.18% and 33.33% lower than that of raw RDX,respectively.It demonstrates that safety of spherical RDX under thermal,impact and friction stimuli has been improved.
基金Project supported by the National Natural Science Foundation of China （Grant No 60577033）, the Specialized Research Fund for the Doctoral Program of Higher Education （Grant No 20050003010） and the Basic Research Foundation of Tsinghua National Laboratory for Information Science and Technology.
文摘The influence of degenerate four-wave mixing （FWM） on the performance of supercontinuum-based multiwavelength optical source has been investigated in detail experimentally and theoretically. Numerical simulation results show that the degenerate FWM effect has a deteriorative influence on the spectral uniformity and the optical signal-to-noise ratio （OSNR） of supercontinuum-based optical source, and by suppressing degenerate FWM effect the performance enhancement of the supercontinuum can be achieved successfully. These results are also confirmed by our experiments. Experimentally, by suppressing degenerate FWM the crosstalk of adjacent channels to the filtered channel can be reduced by as much as 15 dB, and consequently the measured receiver sensitivity at 10 Gbit/s for the filtered optical source is improved from -1.7 to -17.8 dBm.
