Permanent magnet synchronous motor(PMSM)speed control systems with conventional linear active disturbance rejection control(CLADRC)strategy encounter issues regarding the coupling between dynamic response and disturba...Permanent magnet synchronous motor(PMSM)speed control systems with conventional linear active disturbance rejection control(CLADRC)strategy encounter issues regarding the coupling between dynamic response and disturbance suppression and have poor performance in suppressing complex nonlinear disturbances.In order to address these issues,this paper proposes an improved two-degree-of-freedom LADRC(TDOF-LADRC)strategy,which can enhance the disturbance rejection performance of the system while decoupling entirely the system's dynamic and anti-disturbance performance to boost the system robustness and simplify controller parameter tuning.PMSM models that consider total disturbances are developed to design the TDOF-LADRC speed controller accurately.Moreover,to evaluate the control performance of the TDOF-LADRC strategy,its stability is proven,and the influence of each controller parameter on the system control performance is analyzed.Based on it,a comparison is made between the disturbance observation ability and anti-disturbance performance of TDOF-LADRC and CLADRC to prove the superiority of TDOF-LADRC in rejecting disturbances.Finally,experiments are performed on a 750 W PMSM experimental platform,and the results demonstrate that the proposed TDOF-LADRC exhibits the properties of two degrees of freedom and improves the disturbance rejection performance of the PMSM system.展开更多
Neural networks require a lot of training to understand the model of a plant or a process. Issues such as learning speed, stability, and weight convergence remain as areas of research and comparison of many training a...Neural networks require a lot of training to understand the model of a plant or a process. Issues such as learning speed, stability, and weight convergence remain as areas of research and comparison of many training algorithms. The application of neural networks to control interior permanent magnet synchronous motor using direct torque control （DTC） is discussed. A neural network is used to emulate the state selector of the DTC. The neural networks used are the back-propagation and radial basis function. To reduce the training patterns and increase the execution speed of the training process, the inputs of switching table are converted to digital signals, i.e., one bit represent the flux error, one bit the torque error, and three bits the region of stator flux. Computer simulations of the motor and neural-network system using the two approaches are presented and compared. Discussions about the back-propagation and radial basis function as the most promising training techniques are presented, giving its advantages and disadvantages. The system using back-propagation and radial basis function networks controller has quick parallel speed and high torque response.展开更多
A fuzzy sliding-mode control (FSMC) scheme based on T-S fuzzy models was proposed for the permanent magnet synchronous motor (PMSM) drive system to solve the speed tracking problem. A T-S fuzzy model was firstly forme...A fuzzy sliding-mode control (FSMC) scheme based on T-S fuzzy models was proposed for the permanent magnet synchronous motor (PMSM) drive system to solve the speed tracking problem. A T-S fuzzy model was firstly formed to represent the nonlinear system of PMSM. For converting the tracking control into a stabilization problem, a new control design was proposed to define the internal desired states. Then, the FSMC controller for PMSM system with parameter variation and load disturbance was designed based on the fuzzy model. The performance of the proposed controller was verified by experimental results on PMSM system. The results show that the FSMC scheme can drive the dynamics of PMSM into a designated sliding surface in finite time and guarantee the property of asymptotical stability. The information of upper bound of modeling errors as well as perturbations is not required when using the FSMC controller.展开更多
单相开路故障的五相永磁同步电机(permanent-magnet synchronous motor,PMSM)采用有限集模型预测转矩和磁链控制(finite-control-set model predictive torque and flux control,FCS-MPTFC)策略,存在转矩脉动大、价值函数的权重系数整...单相开路故障的五相永磁同步电机(permanent-magnet synchronous motor,PMSM)采用有限集模型预测转矩和磁链控制(finite-control-set model predictive torque and flux control,FCS-MPTFC)策略,存在转矩脉动大、价值函数的权重系数整定困难、迭代计算量大以及共模电压(commonmode voltage,CMV)高等问题。为此,该文提出一种简化FCS-MPTFC策略。首先,建立五相PMSM在单相开路故障情况下的数学模型,并分析CMV产生的机理。其次,以抑制3次谐波电流的原则合成等幅值虚拟电压矢量(virtual voltage vector,V^(3)),并将转矩和磁链价值函数等效转化为电压价值函数,同时采用无差拍控制思想计算出参考电压矢量,进而通过合理划分扇区,直接获得最优V^(3)。最后,选择方向相反的两个基电压矢量代替零矢量,以减小开路故障下的CMV。仿真和实验结果表明:所提控制策略不仅能抑制单相开路故障导致的转矩脉动、降低计算负荷和CMV、抑制电流谐波,而且具有优良的稳态和动态性能。展开更多
针对传统谐振控制器与PI控制器并联(PIR)无法克服积分环节饱和等因素引起的系统动态过程中超调震荡问题,提出了一种改进双环自抗扰谐振控制器(dual-loop active disturbance rejection control,DLADRC)。DLADRC速度环与电流环均采用自...针对传统谐振控制器与PI控制器并联(PIR)无法克服积分环节饱和等因素引起的系统动态过程中超调震荡问题,提出了一种改进双环自抗扰谐振控制器(dual-loop active disturbance rejection control,DLADRC)。DLADRC速度环与电流环均采用自抗扰控制,速度环采用传统的自抗扰控制。电流环采用一种改进的谐振扩张状态观测器,将观测电流作为谐振控制器的输入,令谐振控制器的输出直接作用到电流环输出,从而降低了谐振电流环设计的复杂性。双环自抗扰谐振控制器保留了谐振控制器抑制特定频率谐波电流的特性,同时优化了系统的超调量与调节时间,有效提升了谐振控制系统的动态性能。仿真结果验证DLADRC系统的有效性。展开更多
在五相永磁同步电机(permanent-magnet synchronous motor,PMSM)中,有限集模型预测容错控制(finite control set model predictive fault tolerant control,FCS-MPFTC)存在计算量大、电流谐波含量高等问题。因此,该文提出一种简化FCS-MP...在五相永磁同步电机(permanent-magnet synchronous motor,PMSM)中,有限集模型预测容错控制(finite control set model predictive fault tolerant control,FCS-MPFTC)存在计算量大、电流谐波含量高等问题。因此,该文提出一种简化FCS-MPFTC来实现相开路和短路故障情况下的统一容错控制。首先,将模型预测电流控制的电流代价函数等效转化为电压代价函数,并采用无差拍方法通过电流模型计算出参考电压。然后,基于抑制三次谐波电流为0的原则合成虚拟电压矢量(virtual voltage vector,V^(3));通过重构V^(3)和扇区,以直接获得参考电压矢量对应的最优电压矢量。最后,对传统和简化FCS-MPFTC在开路和短路故障下进行对比实验。结果表明,所提策略能够有效减小故障后计算量、转矩脉动以及电流谐波含量。展开更多
文摘Permanent magnet synchronous motor(PMSM)speed control systems with conventional linear active disturbance rejection control(CLADRC)strategy encounter issues regarding the coupling between dynamic response and disturbance suppression and have poor performance in suppressing complex nonlinear disturbances.In order to address these issues,this paper proposes an improved two-degree-of-freedom LADRC(TDOF-LADRC)strategy,which can enhance the disturbance rejection performance of the system while decoupling entirely the system's dynamic and anti-disturbance performance to boost the system robustness and simplify controller parameter tuning.PMSM models that consider total disturbances are developed to design the TDOF-LADRC speed controller accurately.Moreover,to evaluate the control performance of the TDOF-LADRC strategy,its stability is proven,and the influence of each controller parameter on the system control performance is analyzed.Based on it,a comparison is made between the disturbance observation ability and anti-disturbance performance of TDOF-LADRC and CLADRC to prove the superiority of TDOF-LADRC in rejecting disturbances.Finally,experiments are performed on a 750 W PMSM experimental platform,and the results demonstrate that the proposed TDOF-LADRC exhibits the properties of two degrees of freedom and improves the disturbance rejection performance of the PMSM system.
基金the National Natural Science Foundation of China (60374032).
文摘Neural networks require a lot of training to understand the model of a plant or a process. Issues such as learning speed, stability, and weight convergence remain as areas of research and comparison of many training algorithms. The application of neural networks to control interior permanent magnet synchronous motor using direct torque control （DTC） is discussed. A neural network is used to emulate the state selector of the DTC. The neural networks used are the back-propagation and radial basis function. To reduce the training patterns and increase the execution speed of the training process, the inputs of switching table are converted to digital signals, i.e., one bit represent the flux error, one bit the torque error, and three bits the region of stator flux. Computer simulations of the motor and neural-network system using the two approaches are presented and compared. Discussions about the back-propagation and radial basis function as the most promising training techniques are presented, giving its advantages and disadvantages. The system using back-propagation and radial basis function networks controller has quick parallel speed and high torque response.
基金Project (60835004) supported by the National Natural Science Foundation of China
文摘A fuzzy sliding-mode control (FSMC) scheme based on T-S fuzzy models was proposed for the permanent magnet synchronous motor (PMSM) drive system to solve the speed tracking problem. A T-S fuzzy model was firstly formed to represent the nonlinear system of PMSM. For converting the tracking control into a stabilization problem, a new control design was proposed to define the internal desired states. Then, the FSMC controller for PMSM system with parameter variation and load disturbance was designed based on the fuzzy model. The performance of the proposed controller was verified by experimental results on PMSM system. The results show that the FSMC scheme can drive the dynamics of PMSM into a designated sliding surface in finite time and guarantee the property of asymptotical stability. The information of upper bound of modeling errors as well as perturbations is not required when using the FSMC controller.
文摘单相开路故障的五相永磁同步电机(permanent-magnet synchronous motor,PMSM)采用有限集模型预测转矩和磁链控制(finite-control-set model predictive torque and flux control,FCS-MPTFC)策略,存在转矩脉动大、价值函数的权重系数整定困难、迭代计算量大以及共模电压(commonmode voltage,CMV)高等问题。为此,该文提出一种简化FCS-MPTFC策略。首先,建立五相PMSM在单相开路故障情况下的数学模型,并分析CMV产生的机理。其次,以抑制3次谐波电流的原则合成等幅值虚拟电压矢量(virtual voltage vector,V^(3)),并将转矩和磁链价值函数等效转化为电压价值函数,同时采用无差拍控制思想计算出参考电压矢量,进而通过合理划分扇区,直接获得最优V^(3)。最后,选择方向相反的两个基电压矢量代替零矢量,以减小开路故障下的CMV。仿真和实验结果表明:所提控制策略不仅能抑制单相开路故障导致的转矩脉动、降低计算负荷和CMV、抑制电流谐波,而且具有优良的稳态和动态性能。
文摘针对传统谐振控制器与PI控制器并联(PIR)无法克服积分环节饱和等因素引起的系统动态过程中超调震荡问题,提出了一种改进双环自抗扰谐振控制器(dual-loop active disturbance rejection control,DLADRC)。DLADRC速度环与电流环均采用自抗扰控制,速度环采用传统的自抗扰控制。电流环采用一种改进的谐振扩张状态观测器,将观测电流作为谐振控制器的输入,令谐振控制器的输出直接作用到电流环输出,从而降低了谐振电流环设计的复杂性。双环自抗扰谐振控制器保留了谐振控制器抑制特定频率谐波电流的特性,同时优化了系统的超调量与调节时间,有效提升了谐振控制系统的动态性能。仿真结果验证DLADRC系统的有效性。
文摘在五相永磁同步电机(permanent-magnet synchronous motor,PMSM)中,有限集模型预测容错控制(finite control set model predictive fault tolerant control,FCS-MPFTC)存在计算量大、电流谐波含量高等问题。因此,该文提出一种简化FCS-MPFTC来实现相开路和短路故障情况下的统一容错控制。首先,将模型预测电流控制的电流代价函数等效转化为电压代价函数,并采用无差拍方法通过电流模型计算出参考电压。然后,基于抑制三次谐波电流为0的原则合成虚拟电压矢量(virtual voltage vector,V^(3));通过重构V^(3)和扇区,以直接获得参考电压矢量对应的最优电压矢量。最后,对传统和简化FCS-MPFTC在开路和短路故障下进行对比实验。结果表明,所提策略能够有效减小故障后计算量、转矩脉动以及电流谐波含量。
