In order to predict the powder flow law of the injection molding process of MgTiO3 ceramic parts with complex structures,a constitutive model and numerical simulation method for MgTiO3 ceramic injection molding were e...In order to predict the powder flow law of the injection molding process of MgTiO3 ceramic parts with complex structures,a constitutive model and numerical simulation method for MgTiO3 ceramic injection molding were established based on the Hunt method.The material parameters of MgTiO3 such as elastic modulus,Poisson ratio,glass transition temperature,thermal conductivity and specific heat capacity were measured.Based on the fitting curve and the material parameters measured,the cross-WLF viscosity model and P-V-T model required for MgTiO3 ceramic injection molding were optimized.Furthermore,the influence of process parameters on mold filling flow and distribution of parts defects was researched.It was found that the gate position,injection speed and melt temperature have greater influence on mold filling flow and the packing process has an obvious effect on parts’defects.On this basis,the MgTiO3 ceramic parts injection molding experiment verification was carried out.By comparing the experimental results with the simulated results,it is found that the deformation error is within 1.5%and the density error is within 1%.Therefore,this research provided theoretical guidance for the engineering application of MgTiO3 ceramic parts fabricated by injection molding.展开更多
In order to reduce the "trial-mold" risk and cost,numerical simulation method was applied to micro injection molding weld line development investigation. The micro tensile specimen which has the size of 0.1 ...In order to reduce the "trial-mold" risk and cost,numerical simulation method was applied to micro injection molding weld line development investigation. The micro tensile specimen which has the size of 0.1 mm(depth) ×0.4 mm(width) ×12 mm(length) in test area was selected as the objective part,and polypropylene(PP) as the experimental material. Respectively with specific commercial software(Mold Flow) and general computational fluid dynamic(CFD) software(Comsol Multiphysics) ,the simulation experiments for development of weld line in micro injection molding process were executed and the real comparison experiments were also carried out. The results show that during micro injection molding process,the specific commercial software for normal injection molding process is not valid to describe the micro flow process,the shape of flow front in micro cavity flowing which is important in weld line developing study and the contact angle due to surface tension are not able to be simulated. In order to improve the simulation results for micro weld line development,the general CFD software,which is more flexible in user defining function,is applied. The results show better effects in describing micro fluid flow behavior. As a conclusion,as for weld line forming process,the numerical simulation method can give a characteristic analysis results for processing parameters optimizing in micro injection molding process;but for both kinds of softwares quantitative analysis cannot be obtained unless the boundary condition and micro fluid mathematic model are improved in the future.展开更多
The effects of the binder composition, the powder loading, the thermal properties of feedstocks, and the injection molding parameters on the compact shape retention for metal injection molding 17-4PH stainless steel w...The effects of the binder composition, the powder loading, the thermal properties of feedstocks, and the injection molding parameters on the compact shape retention for metal injection molding 17-4PH stainless steel were investigated. The high-density polyethylene is more effective than ethylene vinyl acetate as a second component of the wax-based binder to retain compact shape due to its higher pyrolytic temperature and less heat of fusion. The compact distortion decreases with increasing the powder loading, molding pressure and molding temperature. There exists an optimal process combination including the powder loading of 68%, molding pressure of 120MPa and molding temperature of 150℃. Under this process condition, the percentage of distorted compacts is the lowest.展开更多
The driving force for using powder metallurgy(PM)mostly relies on its near net-shape ability and cost-performance ratio.The automotive application is a main market of PM industry,requiring parts with competitive mecha...The driving force for using powder metallurgy(PM)mostly relies on its near net-shape ability and cost-performance ratio.The automotive application is a main market of PM industry,requiring parts with competitive mechanical or functional performance in a mass production scale.As the automobile technology transforms from traditional internal combustion engine vehicles to new energy vehicles,PM technology is undergoing significant changes in manufacturing and materials development.This review outlines the challenges and opportunities generated by the changes in the automotive technology for PM.Low-cost,high-performance and light-weight are critical aspects for future PM materials development.Therefore,the studies on PM lean-alloyed steel,aluminum alloys,and titanium alloy materials were reviewed.In addition,PM soft magnetic composite applied to new energy vehicles was discussed.Then new opportunities for advanced processing,such as metal injection molding(MIM)and additive manufacturing(AM),in automotive industry were stated.In general,the change in automotive industry raises sufficient development space for PM.While,emerging technologies require more preeminent PM materials.Iron-based parts are still the main PM products due to their mechanical performance and low cost.MIM will occupy the growing market of highly flexible and complex parts.AM opens a door for fast prototyping,great flexibility and customizing at low cost,driving weight and assembling reduction.展开更多
The injection molding products with different volume ratios of ZrO2 ceramic powder to 316L stainless steel powder were prepared. Properties and structure of the products were characterized by X-ray diffraction（XRD）,...The injection molding products with different volume ratios of ZrO2 ceramic powder to 316L stainless steel powder were prepared. Properties and structure of the products were characterized by X-ray diffraction（XRD）, scanning electron microscope（SEM） and transmission electron microscope （TEM）. The results show that the compressive stress exists in the products and the bend strength reaches 300MPa. ZrO2 phase and stainless steel phase are uniform in samples. The toughness of ceramic increases with the increasing the content of stainless steel. Through TEM study of the interface, some crystalline orientation relationships are determined.展开更多
基金Project(2018CFB439)supported by the Hubei Province Natural Science Foundation,China。
文摘In order to predict the powder flow law of the injection molding process of MgTiO3 ceramic parts with complex structures,a constitutive model and numerical simulation method for MgTiO3 ceramic injection molding were established based on the Hunt method.The material parameters of MgTiO3 such as elastic modulus,Poisson ratio,glass transition temperature,thermal conductivity and specific heat capacity were measured.Based on the fitting curve and the material parameters measured,the cross-WLF viscosity model and P-V-T model required for MgTiO3 ceramic injection molding were optimized.Furthermore,the influence of process parameters on mold filling flow and distribution of parts defects was researched.It was found that the gate position,injection speed and melt temperature have greater influence on mold filling flow and the packing process has an obvious effect on parts’defects.On this basis,the MgTiO3 ceramic parts injection molding experiment verification was carried out.By comparing the experimental results with the simulated results,it is found that the deformation error is within 1.5%and the density error is within 1%.Therefore,this research provided theoretical guidance for the engineering application of MgTiO3 ceramic parts fabricated by injection molding.
基金Project(ZI648/13-1) supported by German Research FoundationProject(D/06/00373) supported by German Academic Exchange Service
文摘In order to reduce the "trial-mold" risk and cost,numerical simulation method was applied to micro injection molding weld line development investigation. The micro tensile specimen which has the size of 0.1 mm(depth) ×0.4 mm(width) ×12 mm(length) in test area was selected as the objective part,and polypropylene(PP) as the experimental material. Respectively with specific commercial software(Mold Flow) and general computational fluid dynamic(CFD) software(Comsol Multiphysics) ,the simulation experiments for development of weld line in micro injection molding process were executed and the real comparison experiments were also carried out. The results show that during micro injection molding process,the specific commercial software for normal injection molding process is not valid to describe the micro flow process,the shape of flow front in micro cavity flowing which is important in weld line developing study and the contact angle due to surface tension are not able to be simulated. In order to improve the simulation results for micro weld line development,the general CFD software,which is more flexible in user defining function,is applied. The results show better effects in describing micro fluid flow behavior. As a conclusion,as for weld line forming process,the numerical simulation method can give a characteristic analysis results for processing parameters optimizing in micro injection molding process;but for both kinds of softwares quantitative analysis cannot be obtained unless the boundary condition and micro fluid mathematic model are improved in the future.
基金Project(2001AA337050) supported by the National High Technology Research and Development Program of China ject(81041) supported by the Huo Yindong Education Foundation project(200135) supported by the Chinese Excellent Dissertation
文摘The effects of the binder composition, the powder loading, the thermal properties of feedstocks, and the injection molding parameters on the compact shape retention for metal injection molding 17-4PH stainless steel were investigated. The high-density polyethylene is more effective than ethylene vinyl acetate as a second component of the wax-based binder to retain compact shape due to its higher pyrolytic temperature and less heat of fusion. The compact distortion decreases with increasing the powder loading, molding pressure and molding temperature. There exists an optimal process combination including the powder loading of 68%, molding pressure of 120MPa and molding temperature of 150℃. Under this process condition, the percentage of distorted compacts is the lowest.
基金Project(51625404)supported by the National Science Fund for Distinguished Young Scholars,China。
文摘The driving force for using powder metallurgy(PM)mostly relies on its near net-shape ability and cost-performance ratio.The automotive application is a main market of PM industry,requiring parts with competitive mechanical or functional performance in a mass production scale.As the automobile technology transforms from traditional internal combustion engine vehicles to new energy vehicles,PM technology is undergoing significant changes in manufacturing and materials development.This review outlines the challenges and opportunities generated by the changes in the automotive technology for PM.Low-cost,high-performance and light-weight are critical aspects for future PM materials development.Therefore,the studies on PM lean-alloyed steel,aluminum alloys,and titanium alloy materials were reviewed.In addition,PM soft magnetic composite applied to new energy vehicles was discussed.Then new opportunities for advanced processing,such as metal injection molding(MIM)and additive manufacturing(AM),in automotive industry were stated.In general,the change in automotive industry raises sufficient development space for PM.While,emerging technologies require more preeminent PM materials.Iron-based parts are still the main PM products due to their mechanical performance and low cost.MIM will occupy the growing market of highly flexible and complex parts.AM opens a door for fast prototyping,great flexibility and customizing at low cost,driving weight and assembling reduction.
文摘The injection molding products with different volume ratios of ZrO2 ceramic powder to 316L stainless steel powder were prepared. Properties and structure of the products were characterized by X-ray diffraction（XRD）, scanning electron microscope（SEM） and transmission electron microscope （TEM）. The results show that the compressive stress exists in the products and the bend strength reaches 300MPa. ZrO2 phase and stainless steel phase are uniform in samples. The toughness of ceramic increases with the increasing the content of stainless steel. Through TEM study of the interface, some crystalline orientation relationships are determined.
