High speed machining has received an important interest because it leads to an increase of productivity and a better workpiece surface quality. However, at high cutting speeds, the tool wear increases dramatically due...High speed machining has received an important interest because it leads to an increase of productivity and a better workpiece surface quality. However, at high cutting speeds, the tool wear increases dramatically due to the high temperature at the tool-workpiece interface. Tool wear impairs the surface finish and hence the tool life is reduced. That is why an important objective of metal cutting research has been the assessment of tool wear patterns and mechanisms. In this paper, wear performances of PCBN tool, ceramic tool, coated carbide tool and fine-grained carbide tool in high speed face milling were presented when cutting cast iron, 45# tempered carbon steel and 45# hardened carbon steel. Tool wear patterns were examined through a tool-making microscope. The research results showed that tool wear types differed in various matching of materials between cutting tool and workpiece. The dominant wear patterns observed were rake face wear, flank wear, chipping, fracture and breakage. The main wear mechanisms were mechanical friction, adhesion, diffusion and chemical wear promoted by cutting forces and high cutting temperature. Hence, the important considerations of high speed cutting tool materials are high heat-resistance and wear-resistance, chemical stability as well as resistance to failure of coatings. The research results will be great benefit to the design and the selection of tool materials and control of tool wear in high-speed machining processes.展开更多
High speed machining (HSM) technology is one of important aspects of advanced manufacturing technology. Nickel-based superalloys have been widely used in the aircraft and nuclear industry due to their exceptional ther...High speed machining (HSM) technology is one of important aspects of advanced manufacturing technology. Nickel-based superalloys have been widely used in the aircraft and nuclear industry due to their exceptional thermal resistance and the ability to retain mechanical properties at elevated temperatures of service environment over 700 ℃. However, they are classified as difficult-to-cut materials due to their high shear strength, work hardening tendency, highly abrasive carbide particles in the microstructure, strong tendency to weld and form built-up edge and low thermal conductivity. They have a tendency to maintain their strength at high temperature that is generated during machining. The Inconel 718 workpiece material used in the experiment was in the hot forged and annealed condition. The commercially available inserts (all inserts were made by Kennametal Inc.) were selected for the tests, a PVD TiAlN coated carbide, a CVD/PVD TiN/TiCN/TiN coated carbide and a CVD Al 2O 3/TiC/TiCN coated carbide were used at the cutting speed range about 50～100 m/min. Three kinds Sialon grade inserts with various geometry and cutting angles were used at the cutting speed range from 100 m/min to 300 m/min. For evaluating the inserts machinability when high speed cutting Inconel 718, Taylor Formula within certain cutting speeds, an high speed cutting experiment of tool life was carried out to establish the models of tool life by means of rapid facing turning test. The conclusions drawn from the turning of Inconel 718 with silicon nitride based ceramic; PVD and CVD coated carbide inserts are as follows: Studies on tool wear in high speed machining. The thorough investigations and studies were made on the tool wear form, wear process and wear mechanism in high speed cutting of difficult-to-machine materials with ceramic tools and with coated carbides. The major wear mechanisms of nickel-based alloys are interactions of abrasive wear, adhesion wear, micro-breakout and chipping. Optimization analysis on the application of high speed machining. Based on the experimental results, the optimal cutting parameters were determined for machining of Inconel 718 at high speed. The recommendation of tool inserts for high speed cutting inconel 718 were ceramic inserts of KY2000 with negative rake angle and KY2100 with round type, the PVD coated carbide insert KC7310 was recommended for its lower price.展开更多
Inconel 718, a high temperature alloy, is extensive ly used in aircraft, gas engines and nuclear-power plants. It is generally known that the life of ceramic cutting tools in machining Inconel 718 is often restric ted...Inconel 718, a high temperature alloy, is extensive ly used in aircraft, gas engines and nuclear-power plants. It is generally known that the life of ceramic cutting tools in machining Inconel 718 is often restric ted by depth-of-cut (DOC) notch wear. In view of the number of various factors involved and the variety of tool materi als and cutting conditions available, the analysis of the DOC notch wear is very difficult. According to previous work concerning the DOC notch wear of ceramics tools, some Al 2O 3 - and Si 3N 4 -based ceramics tools have show n that the degree of tool notching depends on the thermal shock resistance of a tool material and thermal gradients (interrupted cutting, use of flood coolants) . Other observations suggest that there are chemical interactions between the to ol material and the work-piece. At the same time, an analytical technique based on thermodynamic properties for estimating cutting tool wear was proposed. Howe ver, so far, there is no concrete and convincing explanation for the DOC notch w ear. In all previous studies on the DOC notch wear, it is often assumed that notch we ar happened in the contacting region of the cutting tool and the work-piece, wh ile the exact position of notch wear is always neglected. In his article, He Ning measured the distance l n between tool nose and the center of DOC notch wear, and calculated the theoretical working length l d ― the ideal distance between the DOC notch center and the intersection of th e theoretical depth of cut line and the cutting edge. He found that l n is always greater than l d. It means that the position of the DOC notch is not at the depth of cut line, but out of the theoretical cutting area. He supposed that the saw-tooth shaped burrs and fin-shaped chip edges cause the DOC no tch wear, because only the saw-tooth shaped burrs and fin-shaped chip edges ha ve effect on the tools at the region of notch wear. Although He described the reason of notch wear and did some theoretical analysis of it, he has not done some experiments to verify it. In this paper, an experim ent was done to verify He’s assumption about DOC notch wear. In the present exp eriment, which has been done with the ceramic inserts (LT55), Working conditions at the region of DOC notch wear were analyzed. By using a KISTLER 9265B dyn amometer, the dynamic cutting force signals in three directions were pick up. By comparison between the theoretical frequency, with which the saw-shaped burr a nd fin-shaped chip edge impact on the region of notch wear, and the experimenta l results, it can be seen that the high frequency components of dynamic cutting forces mainly result from the impact effects of the saw-shaped burr and fin-sh aped chip edge. In high speed machining of nickel based alloys, DOC notch wear of ceramic tools is mainly because the impact effect of the burr and fin-shaped chip edge causes tools to be of fatigue damage, and the adherence between tool material and work piece material changes the direction of pressure stress and makes the micro-cra ck to appear and extend quickly.展开更多
文摘High speed machining has received an important interest because it leads to an increase of productivity and a better workpiece surface quality. However, at high cutting speeds, the tool wear increases dramatically due to the high temperature at the tool-workpiece interface. Tool wear impairs the surface finish and hence the tool life is reduced. That is why an important objective of metal cutting research has been the assessment of tool wear patterns and mechanisms. In this paper, wear performances of PCBN tool, ceramic tool, coated carbide tool and fine-grained carbide tool in high speed face milling were presented when cutting cast iron, 45# tempered carbon steel and 45# hardened carbon steel. Tool wear patterns were examined through a tool-making microscope. The research results showed that tool wear types differed in various matching of materials between cutting tool and workpiece. The dominant wear patterns observed were rake face wear, flank wear, chipping, fracture and breakage. The main wear mechanisms were mechanical friction, adhesion, diffusion and chemical wear promoted by cutting forces and high cutting temperature. Hence, the important considerations of high speed cutting tool materials are high heat-resistance and wear-resistance, chemical stability as well as resistance to failure of coatings. The research results will be great benefit to the design and the selection of tool materials and control of tool wear in high-speed machining processes.
文摘High speed machining (HSM) technology is one of important aspects of advanced manufacturing technology. Nickel-based superalloys have been widely used in the aircraft and nuclear industry due to their exceptional thermal resistance and the ability to retain mechanical properties at elevated temperatures of service environment over 700 ℃. However, they are classified as difficult-to-cut materials due to their high shear strength, work hardening tendency, highly abrasive carbide particles in the microstructure, strong tendency to weld and form built-up edge and low thermal conductivity. They have a tendency to maintain their strength at high temperature that is generated during machining. The Inconel 718 workpiece material used in the experiment was in the hot forged and annealed condition. The commercially available inserts (all inserts were made by Kennametal Inc.) were selected for the tests, a PVD TiAlN coated carbide, a CVD/PVD TiN/TiCN/TiN coated carbide and a CVD Al 2O 3/TiC/TiCN coated carbide were used at the cutting speed range about 50～100 m/min. Three kinds Sialon grade inserts with various geometry and cutting angles were used at the cutting speed range from 100 m/min to 300 m/min. For evaluating the inserts machinability when high speed cutting Inconel 718, Taylor Formula within certain cutting speeds, an high speed cutting experiment of tool life was carried out to establish the models of tool life by means of rapid facing turning test. The conclusions drawn from the turning of Inconel 718 with silicon nitride based ceramic; PVD and CVD coated carbide inserts are as follows: Studies on tool wear in high speed machining. The thorough investigations and studies were made on the tool wear form, wear process and wear mechanism in high speed cutting of difficult-to-machine materials with ceramic tools and with coated carbides. The major wear mechanisms of nickel-based alloys are interactions of abrasive wear, adhesion wear, micro-breakout and chipping. Optimization analysis on the application of high speed machining. Based on the experimental results, the optimal cutting parameters were determined for machining of Inconel 718 at high speed. The recommendation of tool inserts for high speed cutting inconel 718 were ceramic inserts of KY2000 with negative rake angle and KY2100 with round type, the PVD coated carbide insert KC7310 was recommended for its lower price.
文摘Inconel 718, a high temperature alloy, is extensive ly used in aircraft, gas engines and nuclear-power plants. It is generally known that the life of ceramic cutting tools in machining Inconel 718 is often restric ted by depth-of-cut (DOC) notch wear. In view of the number of various factors involved and the variety of tool materi als and cutting conditions available, the analysis of the DOC notch wear is very difficult. According to previous work concerning the DOC notch wear of ceramics tools, some Al 2O 3 - and Si 3N 4 -based ceramics tools have show n that the degree of tool notching depends on the thermal shock resistance of a tool material and thermal gradients (interrupted cutting, use of flood coolants) . Other observations suggest that there are chemical interactions between the to ol material and the work-piece. At the same time, an analytical technique based on thermodynamic properties for estimating cutting tool wear was proposed. Howe ver, so far, there is no concrete and convincing explanation for the DOC notch w ear. In all previous studies on the DOC notch wear, it is often assumed that notch we ar happened in the contacting region of the cutting tool and the work-piece, wh ile the exact position of notch wear is always neglected. In his article, He Ning measured the distance l n between tool nose and the center of DOC notch wear, and calculated the theoretical working length l d ― the ideal distance between the DOC notch center and the intersection of th e theoretical depth of cut line and the cutting edge. He found that l n is always greater than l d. It means that the position of the DOC notch is not at the depth of cut line, but out of the theoretical cutting area. He supposed that the saw-tooth shaped burrs and fin-shaped chip edges cause the DOC no tch wear, because only the saw-tooth shaped burrs and fin-shaped chip edges ha ve effect on the tools at the region of notch wear. Although He described the reason of notch wear and did some theoretical analysis of it, he has not done some experiments to verify it. In this paper, an experim ent was done to verify He’s assumption about DOC notch wear. In the present exp eriment, which has been done with the ceramic inserts (LT55), Working conditions at the region of DOC notch wear were analyzed. By using a KISTLER 9265B dyn amometer, the dynamic cutting force signals in three directions were pick up. By comparison between the theoretical frequency, with which the saw-shaped burr a nd fin-shaped chip edge impact on the region of notch wear, and the experimenta l results, it can be seen that the high frequency components of dynamic cutting forces mainly result from the impact effects of the saw-shaped burr and fin-sh aped chip edge. In high speed machining of nickel based alloys, DOC notch wear of ceramic tools is mainly because the impact effect of the burr and fin-shaped chip edge causes tools to be of fatigue damage, and the adherence between tool material and work piece material changes the direction of pressure stress and makes the micro-cra ck to appear and extend quickly.
