A procedure of kinematic analysis is presented in this study to assess the reinforcement force of geosynthetics required under seismic loadings, particularly for steep slopes which are hardly able to maintain its stab...A procedure of kinematic analysis is presented in this study to assess the reinforcement force of geosynthetics required under seismic loadings, particularly for steep slopes which are hardly able to maintain its stability. Note that curved sloping surfaces widely exist in natural slopes, but existing literatures were mainly focusing on a planar surface in theoretical derivation, due to complicated calculations. Moreover, the non-uniform soil properties cannot be accounted for in conventional upper bound analysis. Pseudo-dynamic approach is used to represent horizontal and vertical accelerations which vary with time and space. In an effort to resolve the above problems, the discretization technique is developed to generate a discretized failure mechanism, decomposing the whole failure block into various components. An elementary analysis permits calculations of rates of work done by external and internal forces. Finally, the upper bound solution of the required reinforcement force is formulated based on the work rate-based balance equation. A parametric study is carried out to give insights on the implication of influential factors on the performance of geosynthetic-reinforced steep slopes.展开更多
Wicking geotextile(WG)is considered as a possible countermeasure to reduce water content in unsaturated soil.In this research,rainfall tests were carried out to verify the drainage performance of WG.And capillary rise...Wicking geotextile(WG)is considered as a possible countermeasure to reduce water content in unsaturated soil.In this research,rainfall tests were carried out to verify the drainage performance of WG.And capillary rise tests were conducted to study the effect of WG on the prevention of capillary rise.Test results indicated that WG with good drainage performance could drain gravitational and capillary water out of kaolinite soil.For kaolinite soil column with water content of 12%and compaction degree of 90%,the whole process of capillary rise in soil column with a layer of WG was a typical two-stage mode,and the maximum capillary height was about 380 mm,which provided that the WG could work as a barrier to prevent capillary rise effectively.In addition,the total vertical influential regions of WG in kaolinite soil above and below the WG layer were 400 and 100 mm,respectively.展开更多
The effect of geosynthetic reinforcing on bearing capacity of a strip footing resting on georeinforced clayey slopes was investigated.The results of a series of numerical study using finite element analyses on strip f...The effect of geosynthetic reinforcing on bearing capacity of a strip footing resting on georeinforced clayey slopes was investigated.The results of a series of numerical study using finite element analyses on strip footing upon both reinforced and unreinforced clayey slopes were presented.The objectives of this work are to:1) determine the influence of reinforcement on the bearing-capacity of the strip footings adjacent slopes,2) suggest an optimum number of reinforcement and 3) survey the effect of friction angle in clayey soils reinforced by geogrids.The investigations were carried out by varying the edge distance of the footing from slope.Also different numbers of geosynthetic layers were applied to obtaining the maximum bearing capacity and minimum settlement.To achieve the third objective,two different friction angles were used.The results show that the load?settlement behavior and ultimate bearing capacity of footing can be considerably improved by the inclusion of reinforcing layer.But using more than one layer reinforcement,the ultimate bearing capacity does not change considerably.It is also shown that for both reinforced and unreinforced slopes,the bearing capacity increases with an increase in edge distance.In addition,as the soil friction angle is increased,the efficiency of reinforcing reduces.展开更多
A two-dimensional(2-D) finite element(FE) model was developed to analyze the deformation and stress of embankment on soft ground due to widening with different treatment techniques.It is found that the embankment wide...A two-dimensional(2-D) finite element(FE) model was developed to analyze the deformation and stress of embankment on soft ground due to widening with different treatment techniques.It is found that the embankment widening induces transverse gradient change due to differential settlements and horizontal outward movements at the shoulder of the existing embankment.Embankment widening also increases the shear stress along the slope of the existing embankment,especially at the foot of slope.The failure potential due to embankment widening may increase with the increase of widening width when the widening width is smaller than 8.5 m,but may decrease with the increase of widening width as the widening width is greater than 8.5 m.The effectiveness of four ground and embankment treatment techniques,including geosynthetic reinforcement,light-weight embankment,deep mixed columns,and separating wall were compared.The results indicate that these treatments reduce the differential settlements and improve the stability.The light-weight embankment has the most effectiveness among four treatments.By using the fly-ash backfill material in widening,the transverse gradient change decreases from 0.5%-1.3% to 0.26%-0.8% and the maximum horizontal displacement decreases from 2.76 cm to 1.44 cm.展开更多
Geosynthetic-reinforced and pile-supported （GRPS） embankment has been increasingly constructed in a large number of regions and for a wide range of projects in the past decades. However, many disadvantages are expos...Geosynthetic-reinforced and pile-supported （GRPS） embankment has been increasingly constructed in a large number of regions and for a wide range of projects in the past decades. However, many disadvantages are exposed through a lot of applications on conventional technique of GRPS embankment （called CT embankment）, i.e., intolerable settlement and lateral displacement, low geosynthetic efficiency, etc. In view of these disadvantages, the fixed geosynthetic technique of GRPS embankment （called FGT embankment） is developed in this work. In this system, the geosynthetic is fixed on the pile head by the steel bar fulcrum and concrete fixed top. The principles and construction techniques involved in the FGT embankment are described firstly. Then, the numerical analysis method and two-stage analysis method are used to study the performance of FGT embankment, respectively. It is shown that the FGT embankment can provide a better improvement technique to construct a high embankment over soft ground.展开更多
In order to investigate the seismic performance of geosynthetic reinforced and pile supported(GRPS) embankment under seismic loads, an input method for three-dimensional oblique incidence of P wave was proposed. This ...In order to investigate the seismic performance of geosynthetic reinforced and pile supported(GRPS) embankment under seismic loads, an input method for three-dimensional oblique incidence of P wave was proposed. This method is based on the explicit finite element method while considering the viscous-spring artificial boundary(VSAB) condition. Using the proposed method, a numerical study was conducted, and the influence of oblique incidence on the seismic response of GRPS embankment under the oblique incident P waves was analyzed. The results indicate that in comparison with vertical incidence, the oblique incidence can significantly increase the displacement, velocity and acceleration of key locations in the GRPS embankment. The existence of geosynthetics can alleviate the impact of seismic load on the response of the embankment to a certain degree. Moreover, the number of reinforcement layers and modulus of geogrid also greatly influence the seismic performance of GRPS embankment.展开更多
In piled and geosynthetic-reinforced(PGR) embankment, the arching behavior determines the overburden load on piles and subsoils. Placement of geosynthetic is effective in reducing the relative displacement between pil...In piled and geosynthetic-reinforced(PGR) embankment, the arching behavior determines the overburden load on piles and subsoils. Placement of geosynthetic is effective in reducing the relative displacement between pile and subsoil. When the mobilized shear stress is less than the shear strength, partially developed arching will occur. Consequently, existing analytical methods, adopting the ultimate shear strength failure criterion, need to be improved. This study developed a simplified 2 D analytical method, which is based on the developing arching effect, to evaluate the load redistribution of the PGR embankment. Then, the influences of embankment height and internal friction angle, subsoil depth, ratio of pile cap width to pile clear spacing(RPC) and geosynthetic tensile stiffness on the critical height ratio, stress concentration ratio, soil arching ratio, geosynthetic tension and axial strain were investigated. This study suggests that a RPC of 1:1.0 and a one-way of single-layer geosynthetic tensile stiffness of 2000 kN/m should be considered as the sensitivity thresholds for the PGR embankment.展开更多
To overcome the deficiencies of conventional geosynthetic-reinforced and pile-supported (GRPS) embankment, a new improvement technique, fixed geosynthetic technique of GRPS embankment (FGT embankment), was developed a...To overcome the deficiencies of conventional geosynthetic-reinforced and pile-supported (GRPS) embankment, a new improvement technique, fixed geosynthetic technique of GRPS embankment (FGT embankment), was developed and introduced. Based on the discussion about the load transfer mechanism of FGT embankment, a simplified check method of the requirement of geosynthetic tensile strength and a mechanical model of the FGT embankment were proposed. Two conditions, the pile cap and pile beam conditions are considered in the mechanical model. The finite difference method is used to solve the mechanical model owing to the complexity of the differential equations and the soil strata. Then, the numerical procedure is programmed. Finally, a field test is conducted to verify the mechanical model and the calculated results are in good agreement with field measured data.展开更多
文摘A procedure of kinematic analysis is presented in this study to assess the reinforcement force of geosynthetics required under seismic loadings, particularly for steep slopes which are hardly able to maintain its stability. Note that curved sloping surfaces widely exist in natural slopes, but existing literatures were mainly focusing on a planar surface in theoretical derivation, due to complicated calculations. Moreover, the non-uniform soil properties cannot be accounted for in conventional upper bound analysis. Pseudo-dynamic approach is used to represent horizontal and vertical accelerations which vary with time and space. In an effort to resolve the above problems, the discretization technique is developed to generate a discretized failure mechanism, decomposing the whole failure block into various components. An elementary analysis permits calculations of rates of work done by external and internal forces. Finally, the upper bound solution of the required reinforcement force is formulated based on the work rate-based balance equation. A parametric study is carried out to give insights on the implication of influential factors on the performance of geosynthetic-reinforced steep slopes.
基金Projects(41872240,41672280)supported by the National Natural Science Foundation of ChinaProject(2016-1-16-2)supported by Science and Technology Project of Jilin Province Transportation,ChinaProject(SJCX18-0052)supported by the Postgraduate Research&Practice Innovation Program of Jiangsu Province,China。
文摘Wicking geotextile(WG)is considered as a possible countermeasure to reduce water content in unsaturated soil.In this research,rainfall tests were carried out to verify the drainage performance of WG.And capillary rise tests were conducted to study the effect of WG on the prevention of capillary rise.Test results indicated that WG with good drainage performance could drain gravitational and capillary water out of kaolinite soil.For kaolinite soil column with water content of 12%and compaction degree of 90%,the whole process of capillary rise in soil column with a layer of WG was a typical two-stage mode,and the maximum capillary height was about 380 mm,which provided that the WG could work as a barrier to prevent capillary rise effectively.In addition,the total vertical influential regions of WG in kaolinite soil above and below the WG layer were 400 and 100 mm,respectively.
文摘The effect of geosynthetic reinforcing on bearing capacity of a strip footing resting on georeinforced clayey slopes was investigated.The results of a series of numerical study using finite element analyses on strip footing upon both reinforced and unreinforced clayey slopes were presented.The objectives of this work are to:1) determine the influence of reinforcement on the bearing-capacity of the strip footings adjacent slopes,2) suggest an optimum number of reinforcement and 3) survey the effect of friction angle in clayey soils reinforced by geogrids.The investigations were carried out by varying the edge distance of the footing from slope.Also different numbers of geosynthetic layers were applied to obtaining the maximum bearing capacity and minimum settlement.To achieve the third objective,two different friction angles were used.The results show that the load?settlement behavior and ultimate bearing capacity of footing can be considerably improved by the inclusion of reinforcing layer.But using more than one layer reinforcement,the ultimate bearing capacity does not change considerably.It is also shown that for both reinforced and unreinforced slopes,the bearing capacity increases with an increase in edge distance.In addition,as the soil friction angle is increased,the efficiency of reinforcing reduces.
文摘A two-dimensional(2-D) finite element(FE) model was developed to analyze the deformation and stress of embankment on soft ground due to widening with different treatment techniques.It is found that the embankment widening induces transverse gradient change due to differential settlements and horizontal outward movements at the shoulder of the existing embankment.Embankment widening also increases the shear stress along the slope of the existing embankment,especially at the foot of slope.The failure potential due to embankment widening may increase with the increase of widening width when the widening width is smaller than 8.5 m,but may decrease with the increase of widening width as the widening width is greater than 8.5 m.The effectiveness of four ground and embankment treatment techniques,including geosynthetic reinforcement,light-weight embankment,deep mixed columns,and separating wall were compared.The results indicate that these treatments reduce the differential settlements and improve the stability.The light-weight embankment has the most effectiveness among four treatments.By using the fly-ash backfill material in widening,the transverse gradient change decreases from 0.5%-1.3% to 0.26%-0.8% and the maximum horizontal displacement decreases from 2.76 cm to 1.44 cm.
基金Foundation item： Project（51278216） supported by the National Natural Science Foundation of China Project（11-2-05） supported by the Scientific and Technological Project for Shanxi Communication Construction, China Project（HF-08-01-2011-240） supported by the Graduates＇ Innovation Fund of Huazhong University of Science and Technology, China
文摘Geosynthetic-reinforced and pile-supported （GRPS） embankment has been increasingly constructed in a large number of regions and for a wide range of projects in the past decades. However, many disadvantages are exposed through a lot of applications on conventional technique of GRPS embankment （called CT embankment）, i.e., intolerable settlement and lateral displacement, low geosynthetic efficiency, etc. In view of these disadvantages, the fixed geosynthetic technique of GRPS embankment （called FGT embankment） is developed in this work. In this system, the geosynthetic is fixed on the pile head by the steel bar fulcrum and concrete fixed top. The principles and construction techniques involved in the FGT embankment are described firstly. Then, the numerical analysis method and two-stage analysis method are used to study the performance of FGT embankment, respectively. It is shown that the FGT embankment can provide a better improvement technique to construct a high embankment over soft ground.
基金Projects(41202220,41472278,51478438)supported by the National Natural Science Foundation of ChinaProjects(20120022120003,20134101120009)supported by the Research Fund for the Doctoral Program of Higher Education,China+1 种基金Project(2652012065)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(14A560014)supported by the Key Project of Education Department in Henan Province,China
文摘In order to investigate the seismic performance of geosynthetic reinforced and pile supported(GRPS) embankment under seismic loads, an input method for three-dimensional oblique incidence of P wave was proposed. This method is based on the explicit finite element method while considering the viscous-spring artificial boundary(VSAB) condition. Using the proposed method, a numerical study was conducted, and the influence of oblique incidence on the seismic response of GRPS embankment under the oblique incident P waves was analyzed. The results indicate that in comparison with vertical incidence, the oblique incidence can significantly increase the displacement, velocity and acceleration of key locations in the GRPS embankment. The existence of geosynthetics can alleviate the impact of seismic load on the response of the embankment to a certain degree. Moreover, the number of reinforcement layers and modulus of geogrid also greatly influence the seismic performance of GRPS embankment.
基金Project(51508279) supported by the National Natural Science Foundation of ChinaProject(KFJ170104) supported by the Open Fund of National Engineering Laboratory of Highway Maintenance Technology of Changsha University of Science & Technology, China+1 种基金Project(BK20150885) supported by the Jiangsu Provincial Natural Science Fund, ChinaProject(2019003) supported by the Key Laboratory of Ministry of Education for Geomechanics and Embankment Engineering of Hohai University, China。
文摘In piled and geosynthetic-reinforced(PGR) embankment, the arching behavior determines the overburden load on piles and subsoils. Placement of geosynthetic is effective in reducing the relative displacement between pile and subsoil. When the mobilized shear stress is less than the shear strength, partially developed arching will occur. Consequently, existing analytical methods, adopting the ultimate shear strength failure criterion, need to be improved. This study developed a simplified 2 D analytical method, which is based on the developing arching effect, to evaluate the load redistribution of the PGR embankment. Then, the influences of embankment height and internal friction angle, subsoil depth, ratio of pile cap width to pile clear spacing(RPC) and geosynthetic tensile stiffness on the critical height ratio, stress concentration ratio, soil arching ratio, geosynthetic tension and axial strain were investigated. This study suggests that a RPC of 1:1.0 and a one-way of single-layer geosynthetic tensile stiffness of 2000 kN/m should be considered as the sensitivity thresholds for the PGR embankment.
基金Project(51278216) supported by the National Natural Science Foundation of ChinaProject(20091341) supported by the Scientific Research Foundation for Returned Overseas Chinese Scholars,Ministry of Education,ChinaProject(HF-08-01-2011-240) supported by the Graduates’ Innovation Fund of Huazhong University of Science and Technology,China
文摘To overcome the deficiencies of conventional geosynthetic-reinforced and pile-supported (GRPS) embankment, a new improvement technique, fixed geosynthetic technique of GRPS embankment (FGT embankment), was developed and introduced. Based on the discussion about the load transfer mechanism of FGT embankment, a simplified check method of the requirement of geosynthetic tensile strength and a mechanical model of the FGT embankment were proposed. Two conditions, the pile cap and pile beam conditions are considered in the mechanical model. The finite difference method is used to solve the mechanical model owing to the complexity of the differential equations and the soil strata. Then, the numerical procedure is programmed. Finally, a field test is conducted to verify the mechanical model and the calculated results are in good agreement with field measured data.
