In order to investigate the effect of sampling frequency and time on pressure fluctuations, the three-dimensional unsteady numerical simulations were conducted in a circulating water pump. Through comparison of turbul...In order to investigate the effect of sampling frequency and time on pressure fluctuations, the three-dimensional unsteady numerical simulations were conducted in a circulating water pump. Through comparison of turbulence models with hydraulic performance experiment, SST k-co model was confirmed to study the rational determination of sampling frequency and time better. The Fast Fourier Transform （FFT） technology was then adopted to process those fluctuating pressure signals obtained. On these bases, the characteristics of pressure fluctuations acting on the tongue were discussed. It is found that aliasing errors decrease at higher sampling frequency of 17 640 Hz, but not at a lower sampling frequency of 1 764 Hz. Correspondingly, an output frequency range ten-times wider is obtained at 17 640 Hz. Compared with 8R, when the sampling time is shorter, the amplitudes may be overvalued, and the frequencies and amplitudes of low-frequency fluctuations can not be well predicted. The frequencies at the tongue are in good agreement with the values calculated by formula and the frequency compositions less than the blade passing frequency are accurately predicted.展开更多
Calculation grid and turbulence model for numerical simulating pressure fluctuations in a high-speed train tunnel are studied through the comparison analysis of numerical simulation and moving model test.Compared the ...Calculation grid and turbulence model for numerical simulating pressure fluctuations in a high-speed train tunnel are studied through the comparison analysis of numerical simulation and moving model test.Compared the waveforms and peak-peak values of pressure fluctuations between numerical simulation and moving model test,the structured grid and the SST k-ωturbulence model are selected for numerical simulating the process of high-speed train passing through the tunnel.The largest value of pressure wave amplitudes of numerical simulation and moving model test meet each other.And the locations of the largest value of the initial compression and expansion wave amplitude of numerical simulation are in agreement with that of moving model test.The calculated pressure at the measurement point fully conforms to the propagation law of compression and expansion waves in the tunnel.展开更多
A three-dimensional transient numerical simulation was conducted to study the pressure fluctuations in low-specific-speed centrifugal pumps. The characteristics of the inner flow were investigated using the SST k-ω t...A three-dimensional transient numerical simulation was conducted to study the pressure fluctuations in low-specific-speed centrifugal pumps. The characteristics of the inner flow were investigated using the SST k-ω turbulence model. The distributions of pressure fluctuations in the impeller and the volute were recorded, and the pressure fluctuation intensity was analyzed comprehensively, at the design condition, using statistical methods. The results show that the pressure fluctuation intensity increases along the impeller streamline from the leading edge to the trailing edge. In the impeller passage, the intensity near the shroud is much higher than that near the hub at thc inlet. However, the intensity at the middle passage is almost equal to the intensity at the outlet. The pressure fluctuation intensity is the highest at the trailing edge on the pressure side and near the tongue because of the rotor-stator interaction. The distribution of pressure fluctuation intensity is symmetrical in the axial cross sections of the volute channel. However, this intensity decreases with increasing radial distance. Hence, the pressure fluctuation intensity can be reduced by modifying the geometry of the leading edge in the impeller and the tongue in the volute.展开更多
The pressure characteristics inside single loop oscillating heat pipe （OHP） having 4.5 mm inner diameter copper tube with the loop height of 440 mm were addressed. Distilled water was used as working fluid inside th...The pressure characteristics inside single loop oscillating heat pipe （OHP） having 4.5 mm inner diameter copper tube with the loop height of 440 mm were addressed. Distilled water was used as working fluid inside the OHP with different filling ratios of 40%, 60% and 80% of total inside volume. Experimental results show that the thermal characteristics are significantly inter-related with pressure fluctuations as well as pressure frequency. And the pressure frequency also depends upon the evaporator temperature that is maintained in the range of 60-96 ℃. Piezoresistive absolute pressure sensor （Model-Kistler 4045A5） was used to take data. The investigation shows that the filling ratio of 60% gives the highest inside pressure magnitude at maximum number of pressure frequency at any of set evaporator temperature and the lowest heat flow resistance is achieved at 60% filling ratio.展开更多
Potential’s fluctuation of rust preventing oil film during its degradation was studied using wirebeam electrode. Being non-destructive and simple, potential measurement is a very repetitive method. Otherelectrochemic...Potential’s fluctuation of rust preventing oil film during its degradation was studied using wirebeam electrode. Being non-destructive and simple, potential measurement is a very repetitive method. Otherelectrochemical testing method, e. g., polarization resistance, can breakdown the integrity of oil coating byDC current; EIS is time consuming. As a special electrochemical sensor, wire beam electrode contains 101wires of mild steel wires, and it is helpful to improve the reproducibility of electrochemical test evidently.Using this electrode, the electrochemical parameters and their distribution which was related to under filmcorrosion process are measured directly so as to describe potential’s fluctuation of rust preventing oil film. Itis pointed out that there is potential’s fluctuation on rust preventing oil film during its degradation, and thischaracteristic has direct effect on the self-repairing ability of rust preventing oil film. However, for the uncoated metal electrode and base oil film, there is no such behavior. It is also pointed out that inhibitors in theoil film have direct effect on its self-repairing ability.展开更多
The stochastic resonance behavior of coupled stochastic resonance(SR)system with time-delay under mass and frequency fluctuations was studied.Firstly,the approximate system model of the time-delay system was obtained ...The stochastic resonance behavior of coupled stochastic resonance(SR)system with time-delay under mass and frequency fluctuations was studied.Firstly,the approximate system model of the time-delay system was obtained by the theory of small time-delay approximation.Then,the random average method and Shapiro-Loginov algorithm were used to calculate the output amplitude ratio of the two subsystems.The simulation analysis shows that increasing the time-delay and the input signal amplitude appropriately can improve the output response of the system.Finally,the system is applied to bearing fault diagnosis and compared with the stochastic resonance system with random mass and random frequency.The experimental results show that the coupled SR system taking into account the actual effect of time-delay and couple can more effectively extract the frequency of the fault signal,and thus realizing the diagnosis of the fault signal,which has important engineering application value.展开更多
The hydrodynamic conditions present in a river delta's formation are a highly important factor in the variation between its sedimentary regulation and characteristics. In the case of the lacustrine basin river-dom...The hydrodynamic conditions present in a river delta's formation are a highly important factor in the variation between its sedimentary regulation and characteristics. In the case of the lacustrine basin river-dominated delta, water level fluctuations and fluviation, are both important controlling factors of the sedimentary characteristics and reservoir architecture. To discuss the effects of water level fluctuation on sediment characteristics and reservoir architecture of this delta, the Fangniugou section in the east of the Songliao Basin was selected for study. Based on an outcrop investigation of the lacustrine basin river-dominated delta, combining with an analysis of the major and trace chemical elements in the sediments to determine the relative water depth, through architecture bounding surfaces and lithofacies division, sedimentary microfacies recognition and architectural element research, this work illustrated the effects of water level fluctuation on the reservoir architecture and established sedimentary models for the lacustrine basin river-dominated delta under various water level conditions. The results show that there are 8 lithofacies in the Fangniugou section. The fan delta front, which is the main object of this study, develops four sedimentary microfacies that include the underwater distributary channel, river mouth bar, sheet sand and interdistributary bay. The effects of water level fluctuation on different orders geographic architecture elements are respectively reflected in the vertical combination of the composite sand bodies, the plane combination of the single sand bodies, the particle size changes in the vertical of hyperplasia in the single sand body, the coset and lamina. In the case of the sand body development of the petroliferous basin, varying water level conditions and research locations resulted in significant variation in the distribution and combination of the sand bodies in the lacustrine basin.展开更多
Different from the stable injection mode of conventional hydraulic fracturing,unstable fluid-injection can bring significant dynamic effect by using variable injection flow rate,which is beneficial to improve the frac...Different from the stable injection mode of conventional hydraulic fracturing,unstable fluid-injection can bring significant dynamic effect by using variable injection flow rate,which is beneficial to improve the fracturing effect.Obviously,the propagation process of fracturing fluid along the pipe string is crucial.In this paper,the fluid transient dynamics model in the pipe string was established,considering the boundary conditions of variable injection flow rate and reservoir seepage,and the unsteady friction was also taken into account.The above model was solved by characteristics and finite difference method respectively.Furthermore,the influences of geological parameters and fluid injection schemes on fluctuating pressure were also analyzed.The results show that unstable fluid-injection can cause noticeable fluctuation of fracturing fluid in the pipe string.Simultaneously,there is attenuation during the propagation of pressure fluctuation.The variation frequency of unstable fluid-injection and well depth have significant effects on pressure fluctuation amplitude at the bottom of the well.This research is conducive to understanding the mechanism of unstable fluid-injection hydraulic fracturing and providing guidance for the design of fluid-injection scheme.展开更多
The Daubechies second order wavelet was applied to decompose pressure fluctuation signals with the gas flux varying from 0.18 to 0.90 m3/h and the solid mass fraction from 0 to 20% and scales 1?9 detail signals and th...The Daubechies second order wavelet was applied to decompose pressure fluctuation signals with the gas flux varying from 0.18 to 0.90 m3/h and the solid mass fraction from 0 to 20% and scales 1?9 detail signals and the 9th scale approximation signals. The pressure signals were studied by multi-scale and R/S analysis method. Hurst analysis method was applied to analyze multi-fractal characteristics of different scale signals. The results show that the characteristics of mono-fractal under scale 1 and scale 2, and bi-fractal under scale 3?9 are effective in deducing the hydrodynamics in slurry bubbling flow system. The measured pressure signals are decomposed to micro-scale signals, meso-scale signals and macro-scale signals. Micro-scale and macro-scale signals are of mono-fractal characteristics, and meso-scale signals are of bi-fractal characteristics. By analyzing energy distribution of different scale signals,it is shown that pressure fluctuations mainly reflects meso-scale interaction between the particles and the bubble.展开更多
An online dynamic method based on electrical conductivity probe, tensiometer and datataker was presented to measure saturation-capillary pressure （S-p） relation in water-light nonaqueous phase liquid （LNAPL） two-p...An online dynamic method based on electrical conductivity probe, tensiometer and datataker was presented to measure saturation-capillary pressure （S-p） relation in water-light nonaqueous phase liquid （LNAPL） two-phase sandy medium under water level fluctuation. Three-electrode electrical conductivity probe （ECP） was used to measure water saturation. Hydrophobic tensiometer was obtained by spraying waterproof material to the ceramic cup of commercially available hydrophilic tensiometer. A couple of hydrophilic tensiometer and hydrophobic tensiometer were used to measure pore water pressure and pore LNAPL pressure of the sandy medium, respectively. All the signals from ECP and tensiometer were collected by a data taker connected with a computer. The results show that this method can finish the measurement of S-R relation of a complete drainage or imbibition process in less than 60 min. It is much more timesaving compared with 10-40 d of traditional methods. Two cycles of water level fluctuation were produced, and four saturation-capillary pressure relations including two stable residual LNAPL saturations of the sandy medium were obtained during in 350 h. The results show that this method has a good durable performance and feasibility in the porous medium with complicated multiphase flow. Although further studies are needed on the signal stability and accuracy drift of the ECP, this online dynamic method can be used successfully in the rapid characterization of a LNAPL migration in porous media.展开更多
The fluctuation of ground water table of landslide caused by the changing of rain fall and reservoir water level leads the slip zone to possess the complicated deformation features of stepped and vibration.Actual role...The fluctuation of ground water table of landslide caused by the changing of rain fall and reservoir water level leads the slip zone to possess the complicated deformation features of stepped and vibration.Actual role of the ground water fluctuation to landslide is the synthesis of pore pressure,chemical intenerating展开更多
By discretizing the convection terms with AUSM+-up scheme in the rotating coordinate system,a finite volume analysis code based on multi-block structured grids was developed independently so as to realize the numerica...By discretizing the convection terms with AUSM+-up scheme in the rotating coordinate system,a finite volume analysis code based on multi-block structured grids was developed independently so as to realize the numerical solving of internal flow fields of turbomachineries.Taking an unshrouded radial impeller with the working fluid of water vapour as the research object,the flow response to the fluctuation of rotational speed was calculated.By comparing the surface pressure profiles and velocity contours calculated by the code and commercial software respectively,the accuracy of flow solver was verified.The analysis of flow response data indicates that,as the working condition shifts closer towards the surge boundary,the response of flow parameters such as mass flow and aerodynamic torque will be more nonsynchronous with the fluctuation of rotational speed,and also the influence of density variation on mass flow variation will be smaller.Moreover,the transient variation region of working condition performance will deviate farther away from the steady performance curve as the working condition approaches the surge boundary.Compared to the working conditions with small mass flows,the distribution characteristics of pressure difference load on the blade surface vary little under large mass flow conditions.The reduction of fluctuation amplitude of rotational speed exerts no influence on abating the hysteresis of flow response.展开更多
We consider the fluctuation of eigenvalues in factor models and propose a new method for testing the model.Based on the characteristics of eigenvalues,variables of unknown distribution are transformed into statistics ...We consider the fluctuation of eigenvalues in factor models and propose a new method for testing the model.Based on the characteristics of eigenvalues,variables of unknown distribution are transformed into statistics of known distribution through randomization.The test statistic checks for breaks in the structure of factor models,including changes in factor loadings and increases in the number of factors.We give the results of simulation experiments and test the factor structure of the stock return data of China’s and U.S.stock markets from January 1,2017,to December 31,2019.Our method performs well in both simulations and real data.展开更多
The impact of extreme temperatures on the health of individuals in different organizations remains uncertain.We employed stratified analyses to examine the impacts of summer(April-September)daily maximum temperatures ...The impact of extreme temperatures on the health of individuals in different organizations remains uncertain.We employed stratified analyses to examine the impacts of summer(April-September)daily maximum temperatures and winter(October-March)daily minimum temperatures on blood pressure and lipid profiles across government staff,com-pany employees,and researchers.We examined 209,477 physical examination records from a physical examination center in the First Affiliated Hospital of USTC from 2017 to 2021.Employing a segmented regression model within the frame-work of generalized linear regression(GLM),we examined the causal impact of extreme temperatures on health outcomes.Additionally,sensitivity analyses were conducted via distributed lag nonlinear models(DLNMs),with a focus on ob-serving the long-term effects over a period of 21 days.Our findings indicate that government staff face increased health risks during extremely low temperatures,regardless of the season.Compared with participants experiencing median tem-peratures,government staff exposed to extremely low temperatures(below the 10th percentile,below 24℃)in the sum-mer presented maximum increases of 2.32 mmHg(95%CI:1.542-3.098)in diastolic blood pressure and 6.481 mmHg(95%CI:5.368-7.594)in systolic blood pressure.In winter,government staff exposed to temperatures below the 10th per-centile(below 1℃)demonstrated maximum increases of 0.278 mmol/L(95%CI:0.210-0.346)in total cholesterol,0.153 mmol/L(95%CI:0.032-0.274)in triglycerides,and 0.077 mmol/L(95%CI:0.192-0.134)in low-density lipoprotein.Conversely,warm winters benefit company employees,whereas researchers exhibit lower sensitivity to temperature changes in winter.The maximum temperatures in summer and minimum temperatures in winter had greater impacts on in-dividuals.Small temperature fluctuations impact health more than large changes do.Notably,both the maximum and min-imum temperatures were better predictors of health outcomes than the daily average temperature was.Blood pressure con-sistently displayed significant associations with temperature across all three groups,with extremely low temperatures in-creasing the risk and extremely high temperatures reducing it.However,the relationship between temperature and blood lipids is complex.展开更多
To research the loading charactefistc of rocks with different structures cut by helical cutting mechanism （HCM）, three different structures of rock （hard-soft-hard rock, soft-hard rock and soft-hard-soft rock） wer...To research the loading charactefistc of rocks with different structures cut by helical cutting mechanism （HCM）, three different structures of rock （hard-soft-hard rock, soft-hard rock and soft-hard-soft rock） were built. And each type model was further divided into three types when the experiments were carried out. To reduce the errors of cutting load caused by manually configured rock in each test, the cutting load of soft rock was taken as a benchmark, and the differences of the cutting load of the different structures of rocks and the soft rock were used to reflect the cutting load change rules of the HCM. The results indicate that, the cutting load of only the HCM top cutting hard rock is larger than that of only the HCM bottom cutting hard rock for dextral HCM, and the cutting load fluctuation is larger, too. However, when the top and the bottom of the HCM cutting hard rock simultaneously, its cutting load is the largest, but the cutting load fluctuation is the least. And the HCM cutting load increment is increased linearly with the increase of rock compressive strength. The HCM cutting load increment is increased exponentially with the increase of hard rock cutting thickness.展开更多
The basic head shape of high-speed train is determined by its longitudinal type-line(LTL),so it is crucial to optimize its aerodynamic performance.Based on the parametric modeling of LTL constructed by non-uniform rel...The basic head shape of high-speed train is determined by its longitudinal type-line(LTL),so it is crucial to optimize its aerodynamic performance.Based on the parametric modeling of LTL constructed by non-uniform relational B-spline(NURBS)and the fluctuation pressure obtained by large eddy simulation(LES),the Kriging surrogate model(KSM)of LTL was constructed for low aerodynamic noise,and the accuracy of the KSM was improved gradually by adding the sample point with maximum expected improvement(EI)and the optimal point from optimization.The optimal objective was searched with genetic algorithm(GA).The results show that the total fluctuation pressure level(FPL)of the optimal LTL can be 8.7 dB less than that of original one,and the shape optimization method is feasible for low aerodynamic noise design.展开更多
Based on the explicit finite element(FE) method and platform of ABAQUS,considering both the inhomogeneity of soils and concave-convex fluctuation of topography,a large-scale refined two-dimensional(2D) FE nonlinear an...Based on the explicit finite element(FE) method and platform of ABAQUS,considering both the inhomogeneity of soils and concave-convex fluctuation of topography,a large-scale refined two-dimensional(2D) FE nonlinear analytical model for Fuzhou Basin was established.The peak ground motion acceleration(PGA) and focusing effect with depth were analyzed.Meanwhile,the results by wave propagation of one-dimensional(1D) layered medium equivalent linearization method were added for contrast.The results show that:1) PGA at different depths are obviously amplified compared to the input ground motion,amplification effect of both funnel-shaped depression and upheaval areas(based on the shape of bedrock surface) present especially remarkable.The 2D results indicate that the PGA displays a non-monotonic decreasing with depth and a greater focusing effect of some particular layers,while the 1D results turn out that the PGA decreases with depth,except that PGA at few particular depth increases abruptly; 2) To the funnel-shaped depression areas,PGA amplification effect above 8 m depth shows relatively larger,to the upheaval areas,PGA amplification effect from 15 m to 25 m depth seems more significant.However,the regularities of the PGA amplification effect could hardly be found in the rest areas; 3) It appears a higher regression rate of PGA amplification coefficient with depth when under a smaller input motion; 4) The frequency spectral characteristic of input motion has noticeable effects on PGA amplification tendency.展开更多
The effects of aging treatments on the tensile properties and compressive behavior of a thin-walled 6005 aluminum alloy tube were studied.Samples after three natural aging(NA)conditions were subsequently aged at 180℃...The effects of aging treatments on the tensile properties and compressive behavior of a thin-walled 6005 aluminum alloy tube were studied.Samples after three natural aging(NA)conditions were subsequently aged at 180℃ for 0.5−12.0 h artificial aging(AA).Tensile and compressive tests were performed after AA.The results show that for samples with the same NA,the longer the AA time is,the higher the strengths alloy owns,and at the same time the material shows a much lower elongation and faster process from plastic deformation to fracture.However,with NA prolonging,the alloy exhibits much better plastic deformation ability after AA,though its strength is decreased.The major cause of strength and plasticity variation induced by changing NA time is that the size of the main strengtheningβ''precipitates is larger and the density is lower.This character is evaluated by the strain hardening exponent n.Compressive results show that the optimum energy absorption characteristics can be acquired at a moderate n(14<n<17).Large n(n≥18)results in the fracture of tube during axial compression while low n(n≤13)causes lower energy absorption.展开更多
The present work deals with an investigation of the self-starting aerodynamic characteristics of VAWT under fluctuating wind. In contrast to the previous studies, the rotational speed of the turbine is not fixed, the ...The present work deals with an investigation of the self-starting aerodynamic characteristics of VAWT under fluctuating wind. In contrast to the previous studies, the rotational speed of the turbine is not fixed, the rotation of the turbine is determined by the dynamic interaction between the fluctuating wind and turbine. A weak coupling method is developed to simulate the dynamic interaction between the fluctuating wind and passive rotation turbine, and the results show that if the fluctuating wind with appropriate fluctuation amplitude and frequency, the self-starting aerodynamic characteristics of VAWT will be enhanced. It is also found that compared with the fluctuation amplitude, the fluctuation frequency of the variation in wind velocity is shown to have a minor effect on the performance of the turbine. The analysis will provide straightforward physical insight into the self-starting aerodynamic characteristics of VAWT under fluctuating wind.展开更多
In order to study the mechanism of the vortex generation at the bottom of the pump sump below the flare tube,twenty pressure pulsation monitoring points were arranged at the bottom of the pump sump below the flare tub...In order to study the mechanism of the vortex generation at the bottom of the pump sump below the flare tube,twenty pressure pulsation monitoring points were arranged at the bottom of the pump sump below the flare tube,and the pressure fluctuation experiments were carried out under different flow conditions.The experimental results show that the frequency of pressure fluctuation at the bottom of the pump sump is twice of the rotational frequency of the impeller blade.The vortex below the flare tube is easy to generate under the large flow conditions and mainly concentrates at the right front position below the flare tube.The position of the vortex occurring is corresponding to the position of the low-pressure region below flare tube.展开更多
基金Project supported by the Priority Academic Development Program of Jiangsu Higher Education Institutions, ChinaProject(CXZZ12_0680) supported by Postgraduate Innovation Foundation of Jiangsu Province, ChinaProject(12JDG082) supported by the Advanced Talent Foundation of Jiangsu University, China
文摘In order to investigate the effect of sampling frequency and time on pressure fluctuations, the three-dimensional unsteady numerical simulations were conducted in a circulating water pump. Through comparison of turbulence models with hydraulic performance experiment, SST k-co model was confirmed to study the rational determination of sampling frequency and time better. The Fast Fourier Transform （FFT） technology was then adopted to process those fluctuating pressure signals obtained. On these bases, the characteristics of pressure fluctuations acting on the tongue were discussed. It is found that aliasing errors decrease at higher sampling frequency of 17 640 Hz, but not at a lower sampling frequency of 1 764 Hz. Correspondingly, an output frequency range ten-times wider is obtained at 17 640 Hz. Compared with 8R, when the sampling time is shorter, the amplitudes may be overvalued, and the frequencies and amplitudes of low-frequency fluctuations can not be well predicted. The frequencies at the tongue are in good agreement with the values calculated by formula and the frequency compositions less than the blade passing frequency are accurately predicted.
文摘Calculation grid and turbulence model for numerical simulating pressure fluctuations in a high-speed train tunnel are studied through the comparison analysis of numerical simulation and moving model test.Compared the waveforms and peak-peak values of pressure fluctuations between numerical simulation and moving model test,the structured grid and the SST k-ωturbulence model are selected for numerical simulating the process of high-speed train passing through the tunnel.The largest value of pressure wave amplitudes of numerical simulation and moving model test meet each other.And the locations of the largest value of the initial compression and expansion wave amplitude of numerical simulation are in agreement with that of moving model test.The calculated pressure at the measurement point fully conforms to the propagation law of compression and expansion waves in the tunnel.
基金Projects(51239005,51009072) supported by the National Natural Science Foundation of ChinaProject(2011BAF14B04) supported by the National Science&Technology Pillar Program of ChinaProject(13JDG084) supported by the Research Foundation for Advanced Talents of Jiansu University,China
文摘A three-dimensional transient numerical simulation was conducted to study the pressure fluctuations in low-specific-speed centrifugal pumps. The characteristics of the inner flow were investigated using the SST k-ω turbulence model. The distributions of pressure fluctuations in the impeller and the volute were recorded, and the pressure fluctuation intensity was analyzed comprehensively, at the design condition, using statistical methods. The results show that the pressure fluctuation intensity increases along the impeller streamline from the leading edge to the trailing edge. In the impeller passage, the intensity near the shroud is much higher than that near the hub at thc inlet. However, the intensity at the middle passage is almost equal to the intensity at the outlet. The pressure fluctuation intensity is the highest at the trailing edge on the pressure side and near the tongue because of the rotor-stator interaction. The distribution of pressure fluctuation intensity is symmetrical in the axial cross sections of the volute channel. However, this intensity decreases with increasing radial distance. Hence, the pressure fluctuation intensity can be reduced by modifying the geometry of the leading edge in the impeller and the tongue in the volute.
基金Project(2011-0009022) supported by Basic Science Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education,Science and Technology of Korea
文摘The pressure characteristics inside single loop oscillating heat pipe （OHP） having 4.5 mm inner diameter copper tube with the loop height of 440 mm were addressed. Distilled water was used as working fluid inside the OHP with different filling ratios of 40%, 60% and 80% of total inside volume. Experimental results show that the thermal characteristics are significantly inter-related with pressure fluctuations as well as pressure frequency. And the pressure frequency also depends upon the evaporator temperature that is maintained in the range of 60-96 ℃. Piezoresistive absolute pressure sensor （Model-Kistler 4045A5） was used to take data. The investigation shows that the filling ratio of 60% gives the highest inside pressure magnitude at maximum number of pressure frequency at any of set evaporator temperature and the lowest heat flow resistance is achieved at 60% filling ratio.
文摘Potential’s fluctuation of rust preventing oil film during its degradation was studied using wirebeam electrode. Being non-destructive and simple, potential measurement is a very repetitive method. Otherelectrochemical testing method, e. g., polarization resistance, can breakdown the integrity of oil coating byDC current; EIS is time consuming. As a special electrochemical sensor, wire beam electrode contains 101wires of mild steel wires, and it is helpful to improve the reproducibility of electrochemical test evidently.Using this electrode, the electrochemical parameters and their distribution which was related to under filmcorrosion process are measured directly so as to describe potential’s fluctuation of rust preventing oil film. Itis pointed out that there is potential’s fluctuation on rust preventing oil film during its degradation, and thischaracteristic has direct effect on the self-repairing ability of rust preventing oil film. However, for the uncoated metal electrode and base oil film, there is no such behavior. It is also pointed out that inhibitors in theoil film have direct effect on its self-repairing ability.
基金Project(61771085)supported by the National Natural Science Foundation of ChinaProject(KJQN 201900601)supported by the Research Project of Chongqing Educational Commission,China。
文摘The stochastic resonance behavior of coupled stochastic resonance(SR)system with time-delay under mass and frequency fluctuations was studied.Firstly,the approximate system model of the time-delay system was obtained by the theory of small time-delay approximation.Then,the random average method and Shapiro-Loginov algorithm were used to calculate the output amplitude ratio of the two subsystems.The simulation analysis shows that increasing the time-delay and the input signal amplitude appropriately can improve the output response of the system.Finally,the system is applied to bearing fault diagnosis and compared with the stochastic resonance system with random mass and random frequency.The experimental results show that the coupled SR system taking into account the actual effect of time-delay and couple can more effectively extract the frequency of the fault signal,and thus realizing the diagnosis of the fault signal,which has important engineering application value.
基金Project(2011ZX05009-002)supported by the National Key Oil&Gas Project,ChinaProject(15CX06010A)supported by the Fundamental Research Funds for the Central Universities,China
文摘The hydrodynamic conditions present in a river delta's formation are a highly important factor in the variation between its sedimentary regulation and characteristics. In the case of the lacustrine basin river-dominated delta, water level fluctuations and fluviation, are both important controlling factors of the sedimentary characteristics and reservoir architecture. To discuss the effects of water level fluctuation on sediment characteristics and reservoir architecture of this delta, the Fangniugou section in the east of the Songliao Basin was selected for study. Based on an outcrop investigation of the lacustrine basin river-dominated delta, combining with an analysis of the major and trace chemical elements in the sediments to determine the relative water depth, through architecture bounding surfaces and lithofacies division, sedimentary microfacies recognition and architectural element research, this work illustrated the effects of water level fluctuation on the reservoir architecture and established sedimentary models for the lacustrine basin river-dominated delta under various water level conditions. The results show that there are 8 lithofacies in the Fangniugou section. The fan delta front, which is the main object of this study, develops four sedimentary microfacies that include the underwater distributary channel, river mouth bar, sheet sand and interdistributary bay. The effects of water level fluctuation on different orders geographic architecture elements are respectively reflected in the vertical combination of the composite sand bodies, the plane combination of the single sand bodies, the particle size changes in the vertical of hyperplasia in the single sand body, the coset and lamina. In the case of the sand body development of the petroliferous basin, varying water level conditions and research locations resulted in significant variation in the distribution and combination of the sand bodies in the lacustrine basin.
基金Project(CXZZBS 2020052)supported by Postgraduate Innovation Fund Projects of Hebei Province,China。
文摘Different from the stable injection mode of conventional hydraulic fracturing,unstable fluid-injection can bring significant dynamic effect by using variable injection flow rate,which is beneficial to improve the fracturing effect.Obviously,the propagation process of fracturing fluid along the pipe string is crucial.In this paper,the fluid transient dynamics model in the pipe string was established,considering the boundary conditions of variable injection flow rate and reservoir seepage,and the unsteady friction was also taken into account.The above model was solved by characteristics and finite difference method respectively.Furthermore,the influences of geological parameters and fluid injection schemes on fluctuating pressure were also analyzed.The results show that unstable fluid-injection can cause noticeable fluctuation of fracturing fluid in the pipe string.Simultaneously,there is attenuation during the propagation of pressure fluctuation.The variation frequency of unstable fluid-injection and well depth have significant effects on pressure fluctuation amplitude at the bottom of the well.This research is conducive to understanding the mechanism of unstable fluid-injection hydraulic fracturing and providing guidance for the design of fluid-injection scheme.
基金Project(NCET-05-0413)support by the Program for New Century Excellent Talents in UniversityProject(YB0142112) support by Priming Foundation of East China University of Science and Technology
文摘The Daubechies second order wavelet was applied to decompose pressure fluctuation signals with the gas flux varying from 0.18 to 0.90 m3/h and the solid mass fraction from 0 to 20% and scales 1?9 detail signals and the 9th scale approximation signals. The pressure signals were studied by multi-scale and R/S analysis method. Hurst analysis method was applied to analyze multi-fractal characteristics of different scale signals. The results show that the characteristics of mono-fractal under scale 1 and scale 2, and bi-fractal under scale 3?9 are effective in deducing the hydrodynamics in slurry bubbling flow system. The measured pressure signals are decomposed to micro-scale signals, meso-scale signals and macro-scale signals. Micro-scale and macro-scale signals are of mono-fractal characteristics, and meso-scale signals are of bi-fractal characteristics. By analyzing energy distribution of different scale signals,it is shown that pressure fluctuations mainly reflects meso-scale interaction between the particles and the bubble.
基金Project(8151027501000008) supported by Guangdong Natural Science Foundation, ChinaProject(2007490511) supported by the Open Foundation of State Key Laboratory of Hydrology-Water Resources and Hydraulic Engineering, Hohai University, ChinaProject (2006K0006) supported by the Open Foundation of Guangdong Provincial Key Laboratory of Environmental Pollution Control and Remediation Technology, China
文摘An online dynamic method based on electrical conductivity probe, tensiometer and datataker was presented to measure saturation-capillary pressure （S-p） relation in water-light nonaqueous phase liquid （LNAPL） two-phase sandy medium under water level fluctuation. Three-electrode electrical conductivity probe （ECP） was used to measure water saturation. Hydrophobic tensiometer was obtained by spraying waterproof material to the ceramic cup of commercially available hydrophilic tensiometer. A couple of hydrophilic tensiometer and hydrophobic tensiometer were used to measure pore water pressure and pore LNAPL pressure of the sandy medium, respectively. All the signals from ECP and tensiometer were collected by a data taker connected with a computer. The results show that this method can finish the measurement of S-R relation of a complete drainage or imbibition process in less than 60 min. It is much more timesaving compared with 10-40 d of traditional methods. Two cycles of water level fluctuation were produced, and four saturation-capillary pressure relations including two stable residual LNAPL saturations of the sandy medium were obtained during in 350 h. The results show that this method has a good durable performance and feasibility in the porous medium with complicated multiphase flow. Although further studies are needed on the signal stability and accuracy drift of the ECP, this online dynamic method can be used successfully in the rapid characterization of a LNAPL migration in porous media.
文摘The fluctuation of ground water table of landslide caused by the changing of rain fall and reservoir water level leads the slip zone to possess the complicated deformation features of stepped and vibration.Actual role of the ground water fluctuation to landslide is the synthesis of pore pressure,chemical intenerating
基金supported by the National Key Basic Research Program of China (No.2012CB026000 )the National Science Foundation for Young Scientists (No.2014011155)
文摘By discretizing the convection terms with AUSM+-up scheme in the rotating coordinate system,a finite volume analysis code based on multi-block structured grids was developed independently so as to realize the numerical solving of internal flow fields of turbomachineries.Taking an unshrouded radial impeller with the working fluid of water vapour as the research object,the flow response to the fluctuation of rotational speed was calculated.By comparing the surface pressure profiles and velocity contours calculated by the code and commercial software respectively,the accuracy of flow solver was verified.The analysis of flow response data indicates that,as the working condition shifts closer towards the surge boundary,the response of flow parameters such as mass flow and aerodynamic torque will be more nonsynchronous with the fluctuation of rotational speed,and also the influence of density variation on mass flow variation will be smaller.Moreover,the transient variation region of working condition performance will deviate farther away from the steady performance curve as the working condition approaches the surge boundary.Compared to the working conditions with small mass flows,the distribution characteristics of pressure difference load on the blade surface vary little under large mass flow conditions.The reduction of fluctuation amplitude of rotational speed exerts no influence on abating the hysteresis of flow response.
基金supported by the National Natural Science Foundation of China(12001517,72091212)the USTC Research Funds of the Double First-Class Initiative(YD2040002005)the Fundamental Research Funds for the Central Universities(WK2040000026,WK2040000027)。
文摘We consider the fluctuation of eigenvalues in factor models and propose a new method for testing the model.Based on the characteristics of eigenvalues,variables of unknown distribution are transformed into statistics of known distribution through randomization.The test statistic checks for breaks in the structure of factor models,including changes in factor loadings and increases in the number of factors.We give the results of simulation experiments and test the factor structure of the stock return data of China’s and U.S.stock markets from January 1,2017,to December 31,2019.Our method performs well in both simulations and real data.
基金supported by the National Natural Science Foundation of China(72072169)the Fundamental Re-search Funds for the Central Universities(YD2040002015).
文摘The impact of extreme temperatures on the health of individuals in different organizations remains uncertain.We employed stratified analyses to examine the impacts of summer(April-September)daily maximum temperatures and winter(October-March)daily minimum temperatures on blood pressure and lipid profiles across government staff,com-pany employees,and researchers.We examined 209,477 physical examination records from a physical examination center in the First Affiliated Hospital of USTC from 2017 to 2021.Employing a segmented regression model within the frame-work of generalized linear regression(GLM),we examined the causal impact of extreme temperatures on health outcomes.Additionally,sensitivity analyses were conducted via distributed lag nonlinear models(DLNMs),with a focus on ob-serving the long-term effects over a period of 21 days.Our findings indicate that government staff face increased health risks during extremely low temperatures,regardless of the season.Compared with participants experiencing median tem-peratures,government staff exposed to extremely low temperatures(below the 10th percentile,below 24℃)in the sum-mer presented maximum increases of 2.32 mmHg(95%CI:1.542-3.098)in diastolic blood pressure and 6.481 mmHg(95%CI:5.368-7.594)in systolic blood pressure.In winter,government staff exposed to temperatures below the 10th per-centile(below 1℃)demonstrated maximum increases of 0.278 mmol/L(95%CI:0.210-0.346)in total cholesterol,0.153 mmol/L(95%CI:0.032-0.274)in triglycerides,and 0.077 mmol/L(95%CI:0.192-0.134)in low-density lipoprotein.Conversely,warm winters benefit company employees,whereas researchers exhibit lower sensitivity to temperature changes in winter.The maximum temperatures in summer and minimum temperatures in winter had greater impacts on in-dividuals.Small temperature fluctuations impact health more than large changes do.Notably,both the maximum and min-imum temperatures were better predictors of health outcomes than the daily average temperature was.Blood pressure con-sistently displayed significant associations with temperature across all three groups,with extremely low temperatures in-creasing the risk and extremely high temperatures reducing it.However,the relationship between temperature and blood lipids is complex.
基金Project(51005232) supported by the National Natural Science Foundation of ChinaProject(20100481176) supported by the China Postdoctoral Science Foundation
文摘To research the loading charactefistc of rocks with different structures cut by helical cutting mechanism （HCM）, three different structures of rock （hard-soft-hard rock, soft-hard rock and soft-hard-soft rock） were built. And each type model was further divided into three types when the experiments were carried out. To reduce the errors of cutting load caused by manually configured rock in each test, the cutting load of soft rock was taken as a benchmark, and the differences of the cutting load of the different structures of rocks and the soft rock were used to reflect the cutting load change rules of the HCM. The results indicate that, the cutting load of only the HCM top cutting hard rock is larger than that of only the HCM bottom cutting hard rock for dextral HCM, and the cutting load fluctuation is larger, too. However, when the top and the bottom of the HCM cutting hard rock simultaneously, its cutting load is the largest, but the cutting load fluctuation is the least. And the HCM cutting load increment is increased linearly with the increase of rock compressive strength. The HCM cutting load increment is increased exponentially with the increase of hard rock cutting thickness.
基金Projects(50975289,51275531)supported by the National Natural Science Foundation of ChinaProject(201104514)supported by the Special China Postdoctoral Science Foundation,ChinaProject(20100471229)supported by China Postdoctoral Science Foundation
文摘The basic head shape of high-speed train is determined by its longitudinal type-line(LTL),so it is crucial to optimize its aerodynamic performance.Based on the parametric modeling of LTL constructed by non-uniform relational B-spline(NURBS)and the fluctuation pressure obtained by large eddy simulation(LES),the Kriging surrogate model(KSM)of LTL was constructed for low aerodynamic noise,and the accuracy of the KSM was improved gradually by adding the sample point with maximum expected improvement(EI)and the optimal point from optimization.The optimal objective was searched with genetic algorithm(GA).The results show that the total fluctuation pressure level(FPL)of the optimal LTL can be 8.7 dB less than that of original one,and the shape optimization method is feasible for low aerodynamic noise design.
基金Project(2011CB013601) supported by the National Basic Research Program of ChinaProject(51378258) supported by the National Natural Science Foundation of China
文摘Based on the explicit finite element(FE) method and platform of ABAQUS,considering both the inhomogeneity of soils and concave-convex fluctuation of topography,a large-scale refined two-dimensional(2D) FE nonlinear analytical model for Fuzhou Basin was established.The peak ground motion acceleration(PGA) and focusing effect with depth were analyzed.Meanwhile,the results by wave propagation of one-dimensional(1D) layered medium equivalent linearization method were added for contrast.The results show that:1) PGA at different depths are obviously amplified compared to the input ground motion,amplification effect of both funnel-shaped depression and upheaval areas(based on the shape of bedrock surface) present especially remarkable.The 2D results indicate that the PGA displays a non-monotonic decreasing with depth and a greater focusing effect of some particular layers,while the 1D results turn out that the PGA decreases with depth,except that PGA at few particular depth increases abruptly; 2) To the funnel-shaped depression areas,PGA amplification effect above 8 m depth shows relatively larger,to the upheaval areas,PGA amplification effect from 15 m to 25 m depth seems more significant.However,the regularities of the PGA amplification effect could hardly be found in the rest areas; 3) It appears a higher regression rate of PGA amplification coefficient with depth when under a smaller input motion; 4) The frequency spectral characteristic of input motion has noticeable effects on PGA amplification tendency.
基金Project(2019JJ50054)supported by the Natural Science Foundation of Hunan Province,ChinaProjects(51975201,U1664252)supported by the National Natural Science Foundation of China。
文摘The effects of aging treatments on the tensile properties and compressive behavior of a thin-walled 6005 aluminum alloy tube were studied.Samples after three natural aging(NA)conditions were subsequently aged at 180℃ for 0.5−12.0 h artificial aging(AA).Tensile and compressive tests were performed after AA.The results show that for samples with the same NA,the longer the AA time is,the higher the strengths alloy owns,and at the same time the material shows a much lower elongation and faster process from plastic deformation to fracture.However,with NA prolonging,the alloy exhibits much better plastic deformation ability after AA,though its strength is decreased.The major cause of strength and plasticity variation induced by changing NA time is that the size of the main strengtheningβ''precipitates is larger and the density is lower.This character is evaluated by the strain hardening exponent n.Compressive results show that the optimum energy absorption characteristics can be acquired at a moderate n(14<n<17).Large n(n≥18)results in the fracture of tube during axial compression while low n(n≤13)causes lower energy absorption.
基金Projects(61105086,51505347)supported by the National Natural Science Foundation of China
文摘The present work deals with an investigation of the self-starting aerodynamic characteristics of VAWT under fluctuating wind. In contrast to the previous studies, the rotational speed of the turbine is not fixed, the rotation of the turbine is determined by the dynamic interaction between the fluctuating wind and turbine. A weak coupling method is developed to simulate the dynamic interaction between the fluctuating wind and passive rotation turbine, and the results show that if the fluctuating wind with appropriate fluctuation amplitude and frequency, the self-starting aerodynamic characteristics of VAWT will be enhanced. It is also found that compared with the fluctuation amplitude, the fluctuation frequency of the variation in wind velocity is shown to have a minor effect on the performance of the turbine. The analysis will provide straightforward physical insight into the self-starting aerodynamic characteristics of VAWT under fluctuating wind.
基金China Nature Science Funds(51279173)“The 12th Five-year”Key Project of National Science and Technology Support Plan(2015BAD20B01)Jiangsu Water Conservancy Science and Technology Project(2017031)
文摘In order to study the mechanism of the vortex generation at the bottom of the pump sump below the flare tube,twenty pressure pulsation monitoring points were arranged at the bottom of the pump sump below the flare tube,and the pressure fluctuation experiments were carried out under different flow conditions.The experimental results show that the frequency of pressure fluctuation at the bottom of the pump sump is twice of the rotational frequency of the impeller blade.The vortex below the flare tube is easy to generate under the large flow conditions and mainly concentrates at the right front position below the flare tube.The position of the vortex occurring is corresponding to the position of the low-pressure region below flare tube.
