Traditional manufacturing processes for lightweight curved profiles are often associated with lengthy procedures,high costs,low efficiency,and high energy consumption.In order to solve this problem,a new staggered ext...Traditional manufacturing processes for lightweight curved profiles are often associated with lengthy procedures,high costs,low efficiency,and high energy consumption.In order to solve this problem,a new staggered extrusion(SE)process was used to form the curved profile of AZ31 magnesium alloy in this paper.The study investigates the mapping relationship between the curvature,microstructure,and mechanical properties of the formed profiles by using different eccentricities of the die.Scanning electron microscopy(SEM)and electron backscatter diffraction techniques are employed to examine the effects of different eccentricity values(e)on grain morphology,recrystallization mechanisms,texture,and Schmid factors of the products.The results demonstrate that the staggered extrusion method promotes the deep refinement of grain size in the extruded products,with an average grain size of only 15%of the original billet,reaching 12.28μm.The tensile strength and elongation of the curved profiles after extrusion under the eccentricity value of 10 mm,20 mm and 30 mm are significantly higher than those of the billet,with the tensile strength is increased to 250,270,235 MPa,and the engineering strain elongation increased to 10.5%,12.1%,15.9%.This indicates that staggered extrusion enables curvature control of the profiles while improving their strength.展开更多
This study investigates and quantifies some possible sources affecting the position of impact points of small caliber spin-stabilized projectiles(such as 12.7 mm bullets).A comparative experiment utilizing the control...This study investigates and quantifies some possible sources affecting the position of impact points of small caliber spin-stabilized projectiles(such as 12.7 mm bullets).A comparative experiment utilizing the control variable method was designed to figure out the influence of tiny eccentric centroids on the projectiles.The study critically analyzes data obtained from characteristic parameter measurements and precision trials.It also combines Sobol’s algorithm with an artificial intelligence algorithmdAdaptive Neuro-Fuzzy Inference Systems(ANFIS)ein order to conduct global sensitivity analysis and determine which parameters were most influential.The results indicate that the impact points of projectiles with an entry angle of 0°deflected to the left to that of projectiles with an entry angle of 90°.The difference of the mean coordinates of impact points was about 12.61 cm at a target range of 200 m.Variance analysis indicated that the entry angleei.e.the initial position of mass eccentricityehad a notable influence.After global sensitivity analysis,the significance of the effect of mass eccentricity was confirmed again and the most influential factors were determined to be the axial moment and transverse moment of inertia(Izz Iyy),the mass of a projectile(m),the distance between nose and center of mass along the symmetry axis for a projectile(Lm),and the eccentric distance of the centroid(Lr).The results imply that the control scheme by means of modifying mass center(moving mass or mass eccentricity)is promising for designing small-caliber spin-stabilized projectiles.展开更多
Twin-rotor cylinder-embedded piston engine is proposed for dealing with the sealing problems of rotors in twin-rotor piston engine where the existent mature sealing technologies for traditional reciprocating engine ca...Twin-rotor cylinder-embedded piston engine is proposed for dealing with the sealing problems of rotors in twin-rotor piston engine where the existent mature sealing technologies for traditional reciprocating engine can be applied.The quantity and forms of its sealing surfaces are reduced and simplified,and what's more,the advantages of twin-rotor piston engine are inherited,such as high power density and no valve mechanism.Given the motion law of two rotors,its kinematic model is established,and the general expression for some parameters related to engine performance,such as the trajectory,displacement,velocity and acceleration of the piston and centroid trajectory,angular displacement,velocity and acceleration of the rod are presented.By selecting different variation patterns of relative angle of two rotors,the relevant variables are compared.It can be concluded that by designing the relative angle function of two rotors,the volume variation of working chamber can be changed.However,a comprehensive consideration for friction and vibration is necessary because velocity and acceleration are quite different in the different functions,the swing magnitude of rod is proportional to link ratio λ,and the position of rod swing center is controlled by eccentricity e.In order to reduce the lateral force,a smaller value of λ should be selected in the case of the structure,and the value of e should be near 0.95.There is no relationship between the piston stroke and the variation process of relative angle of two rotors,the former is only proportional to the amplitude of relative angle of two rotors.展开更多
To address the eccentric error of circular marks in camera calibration,a circle location method based on the invariance of collinear points and pole–polar constraint is proposed in this paper.Firstly,the centers of t...To address the eccentric error of circular marks in camera calibration,a circle location method based on the invariance of collinear points and pole–polar constraint is proposed in this paper.Firstly,the centers of the ellipses are extracted,and the real concentric circle center projection equation is established by exploiting the cross ratio invariance of the collinear points.Subsequently,since the infinite lines passing through the centers of the marks are parallel,the other center projection coordinates are expressed as the solution problem of linear equations.The problem of projection deviation caused by using the center of the ellipse as the real circle center projection is addressed,and the results are utilized as the true image points to achieve the high precision camera calibration.As demonstrated by the simulations and practical experiments,the proposed method performs a better location and calibration performance by achieving the actual center projection of circular marks.The relevant results confirm the precision and robustness of the proposed approach.展开更多
Axial compression experiments on as received aluminum tubes and tubes with wall thickness eccentricity incorporated by off centre machining showed that the eccentricity caused transition of their collapse mode from ax...Axial compression experiments on as received aluminum tubes and tubes with wall thickness eccentricity incorporated by off centre machining showed that the eccentricity caused transition of their collapse mode from axisymmetric to diamond. The numerical simulation of the collapse phenomenon was undertaken using a static non-linear Finite Element Analysis in ANSYS, and results are found to compare well with the experimental load compression and energy absorption responses for axisymmetric concertina and non-axisymmetric diamond modes. Having validated the numerical model with experiments, it has been used to undertake a systematic study of the load - compression characteristics and collapse mode transitions of the tubes with varying eccentricities in wall thickness and boundary conditions, as well as the material properties.展开更多
Eccentric decoupling blasting is commonly used in underground excavation.Determination of perimeter hole parameters(such as the blasthole diameter,spacing,and burden)based on an eccentric charge structure is vital for...Eccentric decoupling blasting is commonly used in underground excavation.Determination of perimeter hole parameters(such as the blasthole diameter,spacing,and burden)based on an eccentric charge structure is vital for achieving an excellent smooth blasting effect.In this paper,the Riedel-Hiermaier-Thoma(RHT)model was employed to study rock mass damage under smooth blasting.Firstly,the parameters of the RHT model were calibrated by using the existing SHPB experiment,which were then verified by the existing blasting experiment results.Secondly,the influence of different charge structures on the blasting effect was investigated using the RHT model.The simulation results indicated that eccentric charge blasting has an obvious pressure eccentricity effect.Finally,to improve the blasting effect,the smooth blasting parameters were optimized based on an eccentric charge structure.The overbreak and underbreak phenomena were effectively controlled,and a good blasting effect was achieved with the optimized blasting parameters.展开更多
With the technical development of new warhead designs and improvised explosive device protection,irregular casing filled with explosive has been paid more attention recently. In this paper, we studied the fragmentatio...With the technical development of new warhead designs and improvised explosive device protection,irregular casing filled with explosive has been paid more attention recently. In this paper, we studied the fragmentation of a type of D-shaped casing, which is a common asymmetric casing in the field of warhead design. Based on the radiograph technique, static explosive experiments were conducted with D-shaped casings under four different eccentric initiation ratios to explore their fragmentation. A numerical model was then established to simulate the dynamic response of D-shaped casing filled with explosive. The results of numerical simulation were found to agree well with the experimental data.According to the results of numerical simulation and experimental data, the dynamic responses of Dshaped casing were analyzed. The results of the current work pave way for the innovative design of new warhead and for further studying the dynamic response of asymmetric casing.展开更多
Reinforced concrete(RC)structures are generally designed to carry quasi-static gravity loads through almost indispensable components namely slab,however,it may be subjected to high intense loads induced from the impac...Reinforced concrete(RC)structures are generally designed to carry quasi-static gravity loads through almost indispensable components namely slab,however,it may be subjected to high intense loads induced from the impact of projectiles generated by the tornado,falling construction equipment,and also from accidental explosions during their construction and service lifespan.Impacts due to rock/boulder falls do occur on the structures located especially in hilly areas.Such loadings are not predictable but may cause severe damage to the slab/structure.It stimulates structural engineers and researchers to investigate and understand the dynamic response of RC structures under such impulsive loading.This research work first investigates the performance of 1000×1000×75 mm^(3)conventionally reinforced two-way spanning normal strength concrete slab with only tension reinforcement(0.88%)under the concentric impact load(1035 N)using the finite element method based computer code,ABAQUS/Explicit-v.6.15.The impact load is delivered to the centroid of the slab using a solid-steel cylindroconical impactor(drop weight)with a flat nose of diameter 40 mm,having a total mass of 105 kg released from a fixed height of 2500 mm.Two popular concrete constitutive models in ABAQUS namely;Holmquist-Johnson-Cook(HJC)and Concrete Damage Plasticity(CDP),with strain rate effects as per fib MODEL CODE 2010,are used to model the concrete material behavior to impact loading and to simulate the damage to the slab.The slab response using these two models is analyzed and compared with the impact test results.The strain rate effect on the reinforcing steel bars has been incorporated in the analysis using the Malvar and Crawford(1998)approach.A classical elastoplastic kinematic idealization is considered to model the steel impactor and support system.Results reveal that the HJC model gives a little overestimation of peak displacement,maximum acceleration,and damage of the slab while the predictions given by the CDP model are in reasonable agreement with the experimental test results/observations available in the open literature.Following the validation of the numerical model,analyses have been extended to further investigate the damage response of the slab under eccentric impact loadings.In addition to the concentric location(P1)of the impacting device,five locations on a quarter of the slab i.e.,two along the diagonal(P2&P3),the other two along the mid-span(P4&P5),and the last one(P6)between P3 and P5,covering the entire slab,are considered.Computational results have been discussed and compared,and the evaluation of the most damaging location(s)of the impact is investigated.It has been found that the most critical location of the impact is not the centroid of the slab but the eccentric one with the eccentricity of 1/6th of the span from the centroid along the mid-span section.展开更多
A footing may get an eccentric load caused by earthquake or wind, thus the bearing capacity of footing subjected to eccentric load become a fundamental geotechnical problem. The conventional limit equilibrium method u...A footing may get an eccentric load caused by earthquake or wind, thus the bearing capacity of footing subjected to eccentric load become a fundamental geotechnical problem. The conventional limit equilibrium method used for this problem usually evaluates the material properties only by its final strength. But the classical finite element method(FEM) does not necessarily provide a clear collapse mechanism associated with the yield condition of elements. To overcome these defects, a numerical procedure is proposed to create an explicit collapse mode combining a modified smeared shear band approach with a modified initial stress method. To understand the practical performance of sand foundation and verify the performance of the proposed procedure applied to the practical problems, the computing results were compared with the laboratory model tests results and some conventional solutions. Furthermore, because the proposed numerical procedure employs a simple elasto-plastic model which requires a small number of soil parameters, it may be applied directly to practical design works.展开更多
Turn-milling which history dates from the end of the 20th century is one of the advanced metal cutting technologies. It could precisely machine hard materials as an alternative to turning for certain limitations. A se...Turn-milling which history dates from the end of the 20th century is one of the advanced metal cutting technologies. It could precisely machine hard materials as an alternative to turning for certain limitations. A series of orthogonal turn-milling surface veins experiments have been done on the turn-milling machining center by machining aluminum alloy,and then the nexus between the surface veins and the cutting regimes is studied. The mathematical model for surface vein direction angle is established,also the forming mechanics of surface vein direction is analyzed. Its variety regulation presents decreasing trend with as axial feed and cutter rotary speed increasing. For different eccentric distance of orthogonal turn-milling,the surface veins are different.展开更多
The movement mode of the atomizer is a very important parameter during spray deposition process,which has direct influence on the size and surface texture of the billets. To resolve the problem of manufacturing large ...The movement mode of the atomizer is a very important parameter during spray deposition process,which has direct influence on the size and surface texture of the billets. To resolve the problem of manufacturing large size billets,a method of spray deposition by the atomizer with off-center swing was put forward. The atomizer was driven by the alternating current servomotor to swing within 7° at varying speed. The influence of the atomizer parameters,such as translation of the atomizer,swing angle of the atomizer,substrate falling speed and spraying pressure,on the spray deposition was studied. The optimized parameters of the spray deposition process were obtained. The results show that the large size billets with uniform surface quality can be made through adjusting swing frequency and angle of the atomizer,offset distance of the atomizer and inclined angle of the substrate; the valid spray area will decrease and the dimension of top surface will reduce when pressure is less than 0.4 MPa within certain spray distance; meantime,the moving time and cooling time of the droplets are extended,which will lead to loose structure and bad densification. When the pressure,the swing angle and the eccentric offset of the atomization equal 0.5 MPa,7° and 60 mm,respectively,large size billets with fine texture and diameter of 500 mm can be produced.展开更多
基金Project(JQ2022E004)supported by the Natural Science Foundation of Heilongjiang Province,China。
文摘Traditional manufacturing processes for lightweight curved profiles are often associated with lengthy procedures,high costs,low efficiency,and high energy consumption.In order to solve this problem,a new staggered extrusion(SE)process was used to form the curved profile of AZ31 magnesium alloy in this paper.The study investigates the mapping relationship between the curvature,microstructure,and mechanical properties of the formed profiles by using different eccentricities of the die.Scanning electron microscopy(SEM)and electron backscatter diffraction techniques are employed to examine the effects of different eccentricity values(e)on grain morphology,recrystallization mechanisms,texture,and Schmid factors of the products.The results demonstrate that the staggered extrusion method promotes the deep refinement of grain size in the extruded products,with an average grain size of only 15%of the original billet,reaching 12.28μm.The tensile strength and elongation of the curved profiles after extrusion under the eccentricity value of 10 mm,20 mm and 30 mm are significantly higher than those of the billet,with the tensile strength is increased to 250,270,235 MPa,and the engineering strain elongation increased to 10.5%,12.1%,15.9%.This indicates that staggered extrusion enables curvature control of the profiles while improving their strength.
基金supported by the Fundamental Research Funds for the Central Universities,China(grant no.30918012203)the Foundation of National Laboratory,China(grant no.JCKYS2019209C001)。
文摘This study investigates and quantifies some possible sources affecting the position of impact points of small caliber spin-stabilized projectiles(such as 12.7 mm bullets).A comparative experiment utilizing the control variable method was designed to figure out the influence of tiny eccentric centroids on the projectiles.The study critically analyzes data obtained from characteristic parameter measurements and precision trials.It also combines Sobol’s algorithm with an artificial intelligence algorithmdAdaptive Neuro-Fuzzy Inference Systems(ANFIS)ein order to conduct global sensitivity analysis and determine which parameters were most influential.The results indicate that the impact points of projectiles with an entry angle of 0°deflected to the left to that of projectiles with an entry angle of 90°.The difference of the mean coordinates of impact points was about 12.61 cm at a target range of 200 m.Variance analysis indicated that the entry angleei.e.the initial position of mass eccentricityehad a notable influence.After global sensitivity analysis,the significance of the effect of mass eccentricity was confirmed again and the most influential factors were determined to be the axial moment and transverse moment of inertia(Izz Iyy),the mass of a projectile(m),the distance between nose and center of mass along the symmetry axis for a projectile(Lm),and the eccentric distance of the centroid(Lr).The results imply that the control scheme by means of modifying mass center(moving mass or mass eccentricity)is promising for designing small-caliber spin-stabilized projectiles.
文摘Twin-rotor cylinder-embedded piston engine is proposed for dealing with the sealing problems of rotors in twin-rotor piston engine where the existent mature sealing technologies for traditional reciprocating engine can be applied.The quantity and forms of its sealing surfaces are reduced and simplified,and what's more,the advantages of twin-rotor piston engine are inherited,such as high power density and no valve mechanism.Given the motion law of two rotors,its kinematic model is established,and the general expression for some parameters related to engine performance,such as the trajectory,displacement,velocity and acceleration of the piston and centroid trajectory,angular displacement,velocity and acceleration of the rod are presented.By selecting different variation patterns of relative angle of two rotors,the relevant variables are compared.It can be concluded that by designing the relative angle function of two rotors,the volume variation of working chamber can be changed.However,a comprehensive consideration for friction and vibration is necessary because velocity and acceleration are quite different in the different functions,the swing magnitude of rod is proportional to link ratio λ,and the position of rod swing center is controlled by eccentricity e.In order to reduce the lateral force,a smaller value of λ should be selected in the case of the structure,and the value of e should be near 0.95.There is no relationship between the piston stroke and the variation process of relative angle of two rotors,the former is only proportional to the amplitude of relative angle of two rotors.
基金supported by the Aerospace Science and Technology Joint Fund(6141B061505)the National Natural Science Foundation of China(61473100).
文摘To address the eccentric error of circular marks in camera calibration,a circle location method based on the invariance of collinear points and pole–polar constraint is proposed in this paper.Firstly,the centers of the ellipses are extracted,and the real concentric circle center projection equation is established by exploiting the cross ratio invariance of the collinear points.Subsequently,since the infinite lines passing through the centers of the marks are parallel,the other center projection coordinates are expressed as the solution problem of linear equations.The problem of projection deviation caused by using the center of the ellipse as the real circle center projection is addressed,and the results are utilized as the true image points to achieve the high precision camera calibration.As demonstrated by the simulations and practical experiments,the proposed method performs a better location and calibration performance by achieving the actual center projection of circular marks.The relevant results confirm the precision and robustness of the proposed approach.
基金The Author wishes to thank the Dept. Of Science and Technology, India and Natural Science Foundation, China for their support towards his attending the 7th Asia Pacific Symposium on Engg Plasticity and its Application.
文摘Axial compression experiments on as received aluminum tubes and tubes with wall thickness eccentricity incorporated by off centre machining showed that the eccentricity caused transition of their collapse mode from axisymmetric to diamond. The numerical simulation of the collapse phenomenon was undertaken using a static non-linear Finite Element Analysis in ANSYS, and results are found to compare well with the experimental load compression and energy absorption responses for axisymmetric concertina and non-axisymmetric diamond modes. Having validated the numerical model with experiments, it has been used to undertake a systematic study of the load - compression characteristics and collapse mode transitions of the tubes with varying eccentricities in wall thickness and boundary conditions, as well as the material properties.
基金Projects(11802058,52074262)supported by the National Natural Science Foundation of ChinaProjects(BK20170670,BK20180651)supported by the Jiangsu Youth Foundation,China+2 种基金Project(2020QN06)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(SKLGDUEK1803)supported by the State Key Laboratory for Geomechanics and Deep Underground Engineering,ChinaProject supported by the Mass Entrepreneurship and Innovation Project of Jiangsu,China。
文摘Eccentric decoupling blasting is commonly used in underground excavation.Determination of perimeter hole parameters(such as the blasthole diameter,spacing,and burden)based on an eccentric charge structure is vital for achieving an excellent smooth blasting effect.In this paper,the Riedel-Hiermaier-Thoma(RHT)model was employed to study rock mass damage under smooth blasting.Firstly,the parameters of the RHT model were calibrated by using the existing SHPB experiment,which were then verified by the existing blasting experiment results.Secondly,the influence of different charge structures on the blasting effect was investigated using the RHT model.The simulation results indicated that eccentric charge blasting has an obvious pressure eccentricity effect.Finally,to improve the blasting effect,the smooth blasting parameters were optimized based on an eccentric charge structure.The overbreak and underbreak phenomena were effectively controlled,and a good blasting effect was achieved with the optimized blasting parameters.
基金supported by the National Natural Science Foundation of China [grant number 11772059]the National KeyResearch and Development Program of China [grant number 2017yfc0822300]+1 种基金the 111 Project[grant number G20012017001]the Foundation of State Key Laboratory of Explosion Science and Technology of China[grant number KFJJ13-1Z]
文摘With the technical development of new warhead designs and improvised explosive device protection,irregular casing filled with explosive has been paid more attention recently. In this paper, we studied the fragmentation of a type of D-shaped casing, which is a common asymmetric casing in the field of warhead design. Based on the radiograph technique, static explosive experiments were conducted with D-shaped casings under four different eccentric initiation ratios to explore their fragmentation. A numerical model was then established to simulate the dynamic response of D-shaped casing filled with explosive. The results of numerical simulation were found to agree well with the experimental data.According to the results of numerical simulation and experimental data, the dynamic responses of Dshaped casing were analyzed. The results of the current work pave way for the innovative design of new warhead and for further studying the dynamic response of asymmetric casing.
文摘Reinforced concrete(RC)structures are generally designed to carry quasi-static gravity loads through almost indispensable components namely slab,however,it may be subjected to high intense loads induced from the impact of projectiles generated by the tornado,falling construction equipment,and also from accidental explosions during their construction and service lifespan.Impacts due to rock/boulder falls do occur on the structures located especially in hilly areas.Such loadings are not predictable but may cause severe damage to the slab/structure.It stimulates structural engineers and researchers to investigate and understand the dynamic response of RC structures under such impulsive loading.This research work first investigates the performance of 1000×1000×75 mm^(3)conventionally reinforced two-way spanning normal strength concrete slab with only tension reinforcement(0.88%)under the concentric impact load(1035 N)using the finite element method based computer code,ABAQUS/Explicit-v.6.15.The impact load is delivered to the centroid of the slab using a solid-steel cylindroconical impactor(drop weight)with a flat nose of diameter 40 mm,having a total mass of 105 kg released from a fixed height of 2500 mm.Two popular concrete constitutive models in ABAQUS namely;Holmquist-Johnson-Cook(HJC)and Concrete Damage Plasticity(CDP),with strain rate effects as per fib MODEL CODE 2010,are used to model the concrete material behavior to impact loading and to simulate the damage to the slab.The slab response using these two models is analyzed and compared with the impact test results.The strain rate effect on the reinforcing steel bars has been incorporated in the analysis using the Malvar and Crawford(1998)approach.A classical elastoplastic kinematic idealization is considered to model the steel impactor and support system.Results reveal that the HJC model gives a little overestimation of peak displacement,maximum acceleration,and damage of the slab while the predictions given by the CDP model are in reasonable agreement with the experimental test results/observations available in the open literature.Following the validation of the numerical model,analyses have been extended to further investigate the damage response of the slab under eccentric impact loadings.In addition to the concentric location(P1)of the impacting device,five locations on a quarter of the slab i.e.,two along the diagonal(P2&P3),the other two along the mid-span(P4&P5),and the last one(P6)between P3 and P5,covering the entire slab,are considered.Computational results have been discussed and compared,and the evaluation of the most damaging location(s)of the impact is investigated.It has been found that the most critical location of the impact is not the centroid of the slab but the eccentric one with the eccentricity of 1/6th of the span from the centroid along the mid-span section.
基金Projects(cstc2012jjA0510,cstc2013jcyjA30014)supported by Chongqing Natural Science Foundation in ChinaProject(CDJZR12200011)supported by the Fundamental Research Funds for the Central Universities in China+1 种基金Project(KJTD201305)supported by the Innovation Team Building Programs of Chongqing Universities in ChinaProject supported by the Scientific Research Foundation for the Returned Oversea Chinese Scholars
文摘A footing may get an eccentric load caused by earthquake or wind, thus the bearing capacity of footing subjected to eccentric load become a fundamental geotechnical problem. The conventional limit equilibrium method used for this problem usually evaluates the material properties only by its final strength. But the classical finite element method(FEM) does not necessarily provide a clear collapse mechanism associated with the yield condition of elements. To overcome these defects, a numerical procedure is proposed to create an explicit collapse mode combining a modified smeared shear band approach with a modified initial stress method. To understand the practical performance of sand foundation and verify the performance of the proposed procedure applied to the practical problems, the computing results were compared with the laboratory model tests results and some conventional solutions. Furthermore, because the proposed numerical procedure employs a simple elasto-plastic model which requires a small number of soil parameters, it may be applied directly to practical design works.
基金Sponsored by Doctoral Science Foundation of Shenyang Ligong University (BS04007)
文摘Turn-milling which history dates from the end of the 20th century is one of the advanced metal cutting technologies. It could precisely machine hard materials as an alternative to turning for certain limitations. A series of orthogonal turn-milling surface veins experiments have been done on the turn-milling machining center by machining aluminum alloy,and then the nexus between the surface veins and the cutting regimes is studied. The mathematical model for surface vein direction angle is established,also the forming mechanics of surface vein direction is analyzed. Its variety regulation presents decreasing trend with as axial feed and cutter rotary speed increasing. For different eccentric distance of orthogonal turn-milling,the surface veins are different.
基金Project(G1999064900) supported by the National Key Fundamental Research and Development Program of China
文摘The movement mode of the atomizer is a very important parameter during spray deposition process,which has direct influence on the size and surface texture of the billets. To resolve the problem of manufacturing large size billets,a method of spray deposition by the atomizer with off-center swing was put forward. The atomizer was driven by the alternating current servomotor to swing within 7° at varying speed. The influence of the atomizer parameters,such as translation of the atomizer,swing angle of the atomizer,substrate falling speed and spraying pressure,on the spray deposition was studied. The optimized parameters of the spray deposition process were obtained. The results show that the large size billets with uniform surface quality can be made through adjusting swing frequency and angle of the atomizer,offset distance of the atomizer and inclined angle of the substrate; the valid spray area will decrease and the dimension of top surface will reduce when pressure is less than 0.4 MPa within certain spray distance; meantime,the moving time and cooling time of the droplets are extended,which will lead to loose structure and bad densification. When the pressure,the swing angle and the eccentric offset of the atomization equal 0.5 MPa,7° and 60 mm,respectively,large size billets with fine texture and diameter of 500 mm can be produced.
