The depth of penetration(DOP)method is a well-known ballistic test method for characterisation and ranking of ceramic armour materials.The ceramic tile is bonded to a backing material of semi-infinite thickness,and th...The depth of penetration(DOP)method is a well-known ballistic test method for characterisation and ranking of ceramic armour materials.The ceramic tile is bonded to a backing material of semi-infinite thickness,and the penetration depth of the projectile gives a measure of the performance of the ceramic.There is,however,an inherent variability in the results from this test method.In this work,the accuracy and the variability of the DOP method has been investigated in a round robin exercise.Six ballistic test centres took part in the exercise.A test protocol was developed,in which the threat type(projectile and impact conditions)and a procedure on how to prepare the targets were specified.The targets consisted of alumina tiles of two different thicknesses that were bonded to polycarbonate backing cubes.Two different 7.62 mm armour piercing projectiles were employed;one with a hard steel core and one with a tungsten carbide core.The projectiles and the other materials all came from single material batches in order to avoid batch-to-batch variations in material properties.These materials were distributed between the ballistic test centres.The test results of the different ballistic test facilities were collected and compared.There was not a lot of variation between the average DOP values obtained at each laboratory,but the variation in penetration depth between shots was high.The consequence of this variation may be less confidence in the test results,and a statistical method was used to evaluate the required number of tests that are sufficient to obtain an average result with high confidence.In most cases,the required number of tests is much higher than what is practically feasible.This work was conducted as part of the European Defence Agency-project CERAMBALL.展开更多
In the present study,the mechanical and ballistic properties of friction stir welded(FSW)aluminum alloy(AA5754)samples were investigated,both untreated and cryogenically treated,when impacted by a 7.62 mm armour-pierc...In the present study,the mechanical and ballistic properties of friction stir welded(FSW)aluminum alloy(AA5754)samples were investigated,both untreated and cryogenically treated,when impacted by a 7.62 mm armour-piercing(AP)bullet at an impact velocity of 682±20 m/s.The FSW technique was used to prepare the welded samples for AA5754,with an axial force of 7 kN,a feed rate of 20 mm/min,and a speed of 1200 rpm.The cryogenic treatments performed after welding,including deep cryogenic treatment(DCT)at196℃ and shallow cryogenic treatment(SCT)at80℃,for 6 and 72 h,respectively.The microstructure and mechanical characteristics of cryogenically treated and untreated joints were examined.The cryogenic treatment refined the grain size(1.05 μm)and enhanced the microhardness(93 Hv).Moreover,DCT-FSW significantly improved the tensile strength(13.93%)and impact strength(8.45%)compared to untreated FSW sample.Additionally,in untreated FSW samples,the fracture behaviour varied:the impact fracture mode primarily exhibited ductile failure,while the tensile fracture exhibited a mixed fracture mode.In contrast,the tensile and impact fracture modes of the DCT-FSWwere dominated by a ductile failure mode.The DCT-FSW target demonstrated a lower depth of penetration(DOP)of 31 mm compared to the SCT-FSWand untreated FSW targets.Post-ballistic SEM analysis in the crater region of all three zones revealed the formation of frictional grooves,small cracks,and adiabatic shear bands(ASBs).展开更多
High velocity ballistic impact deformation behaviour of Titanium/GFRP Fiber Metal Laminates(FML)has been explored.Both single and multiple projectiles impact conditions were considered.Ti/GFRP FML targets were fabrica...High velocity ballistic impact deformation behaviour of Titanium/GFRP Fiber Metal Laminates(FML)has been explored.Both single and multiple projectiles impact conditions were considered.Ti/GFRP FML targets were fabricated with addition of 5%and 10%weight percentage of boron carbide(B_(4)C)particles.Mechanical properties of Ti/GFRP FML targets were determined as per ASTM standards.High velocity ballistic experiments were conducted using Armour Piercing Projectile(APP)of diameter 7.62 mm and velocity ranging between 350 and 450 m/s.Depth of penetration of the projectile into the target was measured.The deformation behaviour of Ti/GFRP targets with and without the presence of ceramic powder(B_(4)C)was investigated.“Ductile hole growth”failure mode was observed for pure GFRP target when subjected to single projectile impact whereas“plugging”failure mode was noted for Ti/GFRP targets.The presence of B_(4)C(5%by weight)particles has significantly improved the ballistic resistance of the Ti/GFRP FML target by offering frictional resistance to the projectile penetration.Further addition(10%by weight)of B_(4)C has reduced the ballistic performance due to agglomeration.None of the targets showed‘brittle cracking’or‘fragmentation’failures.When compared to the published results of Aluminium(Al 1100/GFRP and Al 6061/GFRP)FMLs,Ti/GFRP FML showed lesser DoP which increases its potential application to aerospace industry.展开更多
Steel-tube-confined concrete(STCC) targets are provided with excellent anti-penetration performance over semi-infinite concrete(SIC) targets since the steel tube imposes passive restraint on the in-filled concrete dur...Steel-tube-confined concrete(STCC) targets are provided with excellent anti-penetration performance over semi-infinite concrete(SIC) targets since the steel tube imposes passive restraint on the in-filled concrete during the penetration process. Grid STCC system with square steel tubes is a potential solution to protective structures. In this paper, experiments of 9-cell grid STCC targets penetrated by 12.7 mm Armor Piercing Projectile(APP) were performed. The influence of side length and thickness of steel tube,steel ratio and impact velocity on anti-penetration performance were taken into account. Additionally,single-cell square STCC targets were also designed and tested for comparison with the 9-cell grid STCC targets. Damage modes and parameters of the tested targets were measured and discussed. Moreover,the stiffness of radial confinement of grid STCC targets is achieved according to the elastic solution of infinite cylindrical shell in Winkler medium. Furthermore, the penetration resistance and depth of penetration(DOP) for grid STCC targets are obtained on the basis of the dynamic finite spherical cavityexpansion(FSCE) models including radial confinement effect. It is shown that the 9-cell grid STCC targets with optimal dimension match of thickness and side length of steel tube can reduce the DOP by about17 % and 23 % in comparison with the SIC targets and single-cell square STCC targets, respectively, due to both the confinement of square steel tube to concrete in the impacted cell and the additional confinement of the surrounding cells to the impacted cell;the penetration resistance and DOP of the grid and cellular STCC targets with similar steel ratio is close, and thus the grid STCC targets with simpler manufacturing process and excellent in-plane expandability are preferred in engineering practice;moreover, the predicted results of DOP model based on the FSCE models agree well with the tested results with the maximum disparity less than 12 % and the proposed model is more applicable to the grid and cellular STCC targets with high radial confinement.展开更多
In this study, high velocity impact behaviour of friction stir welded AA7075-T651 25 mm thick plates were investigated using a 7.62 mm × 51 mm lead core and 7.62 mm × 39 mm steel core projectiles. Prior to b...In this study, high velocity impact behaviour of friction stir welded AA7075-T651 25 mm thick plates were investigated using a 7.62 mm × 51 mm lead core and 7.62 mm × 39 mm steel core projectiles. Prior to ballistic trails, mechanical and metallurgical properties of friction stir welded AA 7075-T651 25 mm thick plates were studied. Microstructural and hardness studies revealed that friction stir welds constituted three distinct regions namely Weld Nugget(WN), Thermo-Mechanically Affected Zone(TMAZ) and Heat Affected Zone(HAZ). Base Material(BM) and all three weld regions were ballistically tested as per military standard NIJ.0108.01 using lead and steel core bullets at maximum permissible velocities of 830 ± 20 and 700 ± 30 m/s, respectively. It has been found that base material(AA7075-T651)and all three weld regions of 25 mm thick plates were able to resist perforation by both types of projectiles used. However depth of penetration has been found to increase from BM to WN, HAZ and TMAZ for both types of projectiles. In all cases steel core projectiles caused higher depth of penetration compared to those caused by lead core projectiles. TMAZs of the friction stir welds were found to be the weakest zone. The fracture that occurred in the base material was spall fragmentation indicating brittle failure, whereas all zones of friction stir welded AA7075-T651 targets with a front petalling, indicating ductile failure. The post-ballistic tested samples showed no significant change in the microstructure of the BM and WN. On the other hand, TMAZ and HAZ showed severe grain deformation in the direction of projectile penetration, and the formation of adiabatic shear bands(ASB). This work showed that 25 mm thick friction stir welded AA7075-T651 joints responded well to ballistic impact loads, making them a good choice for light combat vehicles.展开更多
基金conducted as part of the European Defence Agency-project CERAMBALL,contract number B 1091 GEM1 GP
文摘The depth of penetration(DOP)method is a well-known ballistic test method for characterisation and ranking of ceramic armour materials.The ceramic tile is bonded to a backing material of semi-infinite thickness,and the penetration depth of the projectile gives a measure of the performance of the ceramic.There is,however,an inherent variability in the results from this test method.In this work,the accuracy and the variability of the DOP method has been investigated in a round robin exercise.Six ballistic test centres took part in the exercise.A test protocol was developed,in which the threat type(projectile and impact conditions)and a procedure on how to prepare the targets were specified.The targets consisted of alumina tiles of two different thicknesses that were bonded to polycarbonate backing cubes.Two different 7.62 mm armour piercing projectiles were employed;one with a hard steel core and one with a tungsten carbide core.The projectiles and the other materials all came from single material batches in order to avoid batch-to-batch variations in material properties.These materials were distributed between the ballistic test centres.The test results of the different ballistic test facilities were collected and compared.There was not a lot of variation between the average DOP values obtained at each laboratory,but the variation in penetration depth between shots was high.The consequence of this variation may be less confidence in the test results,and a statistical method was used to evaluate the required number of tests that are sufficient to obtain an average result with high confidence.In most cases,the required number of tests is much higher than what is practically feasible.This work was conducted as part of the European Defence Agency-project CERAMBALL.
文摘In the present study,the mechanical and ballistic properties of friction stir welded(FSW)aluminum alloy(AA5754)samples were investigated,both untreated and cryogenically treated,when impacted by a 7.62 mm armour-piercing(AP)bullet at an impact velocity of 682±20 m/s.The FSW technique was used to prepare the welded samples for AA5754,with an axial force of 7 kN,a feed rate of 20 mm/min,and a speed of 1200 rpm.The cryogenic treatments performed after welding,including deep cryogenic treatment(DCT)at196℃ and shallow cryogenic treatment(SCT)at80℃,for 6 and 72 h,respectively.The microstructure and mechanical characteristics of cryogenically treated and untreated joints were examined.The cryogenic treatment refined the grain size(1.05 μm)and enhanced the microhardness(93 Hv).Moreover,DCT-FSW significantly improved the tensile strength(13.93%)and impact strength(8.45%)compared to untreated FSW sample.Additionally,in untreated FSW samples,the fracture behaviour varied:the impact fracture mode primarily exhibited ductile failure,while the tensile fracture exhibited a mixed fracture mode.In contrast,the tensile and impact fracture modes of the DCT-FSWwere dominated by a ductile failure mode.The DCT-FSW target demonstrated a lower depth of penetration(DOP)of 31 mm compared to the SCT-FSWand untreated FSW targets.Post-ballistic SEM analysis in the crater region of all three zones revealed the formation of frictional grooves,small cracks,and adiabatic shear bands(ASBs).
基金the financial support received from the management of SSN。
文摘High velocity ballistic impact deformation behaviour of Titanium/GFRP Fiber Metal Laminates(FML)has been explored.Both single and multiple projectiles impact conditions were considered.Ti/GFRP FML targets were fabricated with addition of 5%and 10%weight percentage of boron carbide(B_(4)C)particles.Mechanical properties of Ti/GFRP FML targets were determined as per ASTM standards.High velocity ballistic experiments were conducted using Armour Piercing Projectile(APP)of diameter 7.62 mm and velocity ranging between 350 and 450 m/s.Depth of penetration of the projectile into the target was measured.The deformation behaviour of Ti/GFRP targets with and without the presence of ceramic powder(B_(4)C)was investigated.“Ductile hole growth”failure mode was observed for pure GFRP target when subjected to single projectile impact whereas“plugging”failure mode was noted for Ti/GFRP targets.The presence of B_(4)C(5%by weight)particles has significantly improved the ballistic resistance of the Ti/GFRP FML target by offering frictional resistance to the projectile penetration.Further addition(10%by weight)of B_(4)C has reduced the ballistic performance due to agglomeration.None of the targets showed‘brittle cracking’or‘fragmentation’failures.When compared to the published results of Aluminium(Al 1100/GFRP and Al 6061/GFRP)FMLs,Ti/GFRP FML showed lesser DoP which increases its potential application to aerospace industry.
基金the projects supported by the Natural Science Foundation of Hunan Province, China (No. 2018JJ2470 and 2021JJ30776)。
文摘Steel-tube-confined concrete(STCC) targets are provided with excellent anti-penetration performance over semi-infinite concrete(SIC) targets since the steel tube imposes passive restraint on the in-filled concrete during the penetration process. Grid STCC system with square steel tubes is a potential solution to protective structures. In this paper, experiments of 9-cell grid STCC targets penetrated by 12.7 mm Armor Piercing Projectile(APP) were performed. The influence of side length and thickness of steel tube,steel ratio and impact velocity on anti-penetration performance were taken into account. Additionally,single-cell square STCC targets were also designed and tested for comparison with the 9-cell grid STCC targets. Damage modes and parameters of the tested targets were measured and discussed. Moreover,the stiffness of radial confinement of grid STCC targets is achieved according to the elastic solution of infinite cylindrical shell in Winkler medium. Furthermore, the penetration resistance and depth of penetration(DOP) for grid STCC targets are obtained on the basis of the dynamic finite spherical cavityexpansion(FSCE) models including radial confinement effect. It is shown that the 9-cell grid STCC targets with optimal dimension match of thickness and side length of steel tube can reduce the DOP by about17 % and 23 % in comparison with the SIC targets and single-cell square STCC targets, respectively, due to both the confinement of square steel tube to concrete in the impacted cell and the additional confinement of the surrounding cells to the impacted cell;the penetration resistance and DOP of the grid and cellular STCC targets with similar steel ratio is close, and thus the grid STCC targets with simpler manufacturing process and excellent in-plane expandability are preferred in engineering practice;moreover, the predicted results of DOP model based on the FSCE models agree well with the tested results with the maximum disparity less than 12 % and the proposed model is more applicable to the grid and cellular STCC targets with high radial confinement.
基金funding from the Armament Research Board(ARMREB),Defence Research and Development Organization(DRDO),Ministry of Defence,Government of India (Grant no.:ARMREB/MAA/2018/200)。
文摘In this study, high velocity impact behaviour of friction stir welded AA7075-T651 25 mm thick plates were investigated using a 7.62 mm × 51 mm lead core and 7.62 mm × 39 mm steel core projectiles. Prior to ballistic trails, mechanical and metallurgical properties of friction stir welded AA 7075-T651 25 mm thick plates were studied. Microstructural and hardness studies revealed that friction stir welds constituted three distinct regions namely Weld Nugget(WN), Thermo-Mechanically Affected Zone(TMAZ) and Heat Affected Zone(HAZ). Base Material(BM) and all three weld regions were ballistically tested as per military standard NIJ.0108.01 using lead and steel core bullets at maximum permissible velocities of 830 ± 20 and 700 ± 30 m/s, respectively. It has been found that base material(AA7075-T651)and all three weld regions of 25 mm thick plates were able to resist perforation by both types of projectiles used. However depth of penetration has been found to increase from BM to WN, HAZ and TMAZ for both types of projectiles. In all cases steel core projectiles caused higher depth of penetration compared to those caused by lead core projectiles. TMAZs of the friction stir welds were found to be the weakest zone. The fracture that occurred in the base material was spall fragmentation indicating brittle failure, whereas all zones of friction stir welded AA7075-T651 targets with a front petalling, indicating ductile failure. The post-ballistic tested samples showed no significant change in the microstructure of the BM and WN. On the other hand, TMAZ and HAZ showed severe grain deformation in the direction of projectile penetration, and the formation of adiabatic shear bands(ASB). This work showed that 25 mm thick friction stir welded AA7075-T651 joints responded well to ballistic impact loads, making them a good choice for light combat vehicles.
