The Editor-in-Chief has retracted this article [1] because Figures 11 and 12 appear to be identical with Figures 3 and 4respectively from a previously published article [2].Sehrish MUKHTAR,Waqas ASGHAR,Zubair BUTT,Zah...The Editor-in-Chief has retracted this article [1] because Figures 11 and 12 appear to be identical with Figures 3 and 4respectively from a previously published article [2].Sehrish MUKHTAR,Waqas ASGHAR,Zubair BUTT,Zaheer ABBAS,Mudaser ULLAH and Rana ATTA-UR-REHMAN did not respond to correspondence about this retraction.展开更多
Stainless steel(SS)grade 316L is used for orthopedic implants due to its biocompatibility;yet the effort should be done to minimize the carcinogenic and inflammatory effects related to SS 316L implants.In this researc...Stainless steel(SS)grade 316L is used for orthopedic implants due to its biocompatibility;yet the effort should be done to minimize the carcinogenic and inflammatory effects related to SS 316L implants.In this research,aluminide coating of Al–Si alloy on SS 316L is characterized by using optical microscopy,energy dispersive spectroscopy(EDS),nano-indentation and corrosion testing technique.Hot dip aluminizing process is used to coat the SS 316L specimens at 765°C for 2 min immersion time.Half of the specimens are also diffusion treated in a Muffle furnace at 550°C for 4 h to produce diffused specimens of SS 316L.Microstructural examination shows the formation of flat coating/substrate interface due to Si addition.EDS analysis confirms the formation of complex intermetallic at the coating/substrate interface which finally results in increasing the hardness and corrosion resistance properties of coating.展开更多
Intermetallic aluminide compounds possess several potential advantages compared to alloyed steels,like enhanced oxidation resistance,lower density and the omittance of critical raw materials.Iron aluminides,compared t...Intermetallic aluminide compounds possess several potential advantages compared to alloyed steels,like enhanced oxidation resistance,lower density and the omittance of critical raw materials.Iron aluminides,compared to other transition metal-aluminides of TM_(3)-Al type,although having a higher density compared to titan-aluminides,have a lower density compared to nickel-aluminides,but also a higher ductility than both alternatives,making this material potentially effective in ballistic protection application.Density-wise,this material may be a worthy alternative to armour steels,which was the aim of this study.Two materials,Fe_(3)Al intermetallic compound(F3A-C)and Armox 500 armour steel were ballistically tested against tungsten-carbide(WC)armour-piercing ammunition,in accordance with STANAG 4569.After ballistic testing,microhardness and metallographic testing were performed,revealing differences in strain hardening,crack propagation mode and exit hole morphology.F3A-C ballistic resistance is similar to that of armour steel,in spite of the lower tensile and impact mechanical properties,relying on a considerably higher strain hardening rate,thermal properties and a lower density.展开更多
A new process was used for producing FeAl alloy pow de rs with double consumable rotating electrodes and the powders made in this appar atus were analyzed. In this new technology, tungsten rod serves as a cathode ele ...A new process was used for producing FeAl alloy pow de rs with double consumable rotating electrodes and the powders made in this appar atus were analyzed. In this new technology, tungsten rod serves as a cathode ele ctrode, while the alloy rod as an anode electrode. The conventional rotating ele ctrode process must have an anode with pre-melting alloys; however, in this new process, using pure iron as cathode electrode and pure aluminum as anode electr ode can eliminate the step of pre-melting. The effects of process variables, which include electrode rotational speed, a nd electrode diameter of the mean particle diameter were determined. Results showed that both the rotational speed and diameter of electrodes would a ffect the mean diameter of particles. There are three kinds of powders with diff erent composition produced in this study and the possible mechanisms are discuss ed. The process parameters and volume mean diameter of the powders have been cor related to find an experimental equation. The results show that when the rotational speed and the diameter of the anode el ectrode are increased, the powders size will decrease. However, the powders size will increase with cathode electrode.展开更多
The present work explores the feasibility of fabricating porous 3D parts in TiAl intermetallic alloy directly from Tie6Ale4V and Al powders. This approach uses a binder jetting additive manufacturing process followed ...The present work explores the feasibility of fabricating porous 3D parts in TiAl intermetallic alloy directly from Tie6Ale4V and Al powders. This approach uses a binder jetting additive manufacturing process followed by reactive sintering. The results demonstrate that the present approach is successful for realizing parts in TiAl intermetallic alloy.展开更多
The structure and characteristics of dislocation networks in Ti50 Al ordered alloy deformed at room temperature were studied by means of TEM diffraction contrast analysis technique. The results show that the observed...The structure and characteristics of dislocation networks in Ti50 Al ordered alloy deformed at room temperature were studied by means of TEM diffraction contrast analysis technique. The results show that the observed dislocation networks consist of three展开更多
The Al3Ti compound has potential application in the high temperature structure materials due to its low density,high strength and stiffness.The mechanical behaviors of the material under different loading rates were s...The Al3Ti compound has potential application in the high temperature structure materials due to its low density,high strength and stiffness.The mechanical behaviors of the material under different loading rates were studied using compression tests.The results indicate that Al3Ti is a typical brittle material and its compressive strength is dependent on the strain rate.Therefore,a series of rate-dependent constitutive equations are needed to describe its mechanical behaviors accurately.However,it is still short of professional research on the material model for Al3Ti.In this study,the mate rial model was developed on the basis of JH-2 constitutive equations using the experimental data.The model was then applied in simulating the impact process of Ti/Al3Ti metal-intermetallic laminate composites so as to validate the established model.Good agreement between simulation and experiment results shows the constitutive model predict the material responses under high rate and large deformation accurately.This work provides more support for the theoretical and numerical research on the intermetallic.展开更多
文摘The Editor-in-Chief has retracted this article [1] because Figures 11 and 12 appear to be identical with Figures 3 and 4respectively from a previously published article [2].Sehrish MUKHTAR,Waqas ASGHAR,Zubair BUTT,Zaheer ABBAS,Mudaser ULLAH and Rana ATTA-UR-REHMAN did not respond to correspondence about this retraction.
基金sponsored and funded by Metallurgy and Materials Engineering Department,College of Engineering and Emerging Technologies, University of the Punjab (grant no.PU/ASR&TD/ RG-348 dated 26-1-2012)
文摘Stainless steel(SS)grade 316L is used for orthopedic implants due to its biocompatibility;yet the effort should be done to minimize the carcinogenic and inflammatory effects related to SS 316L implants.In this research,aluminide coating of Al–Si alloy on SS 316L is characterized by using optical microscopy,energy dispersive spectroscopy(EDS),nano-indentation and corrosion testing technique.Hot dip aluminizing process is used to coat the SS 316L specimens at 765°C for 2 min immersion time.Half of the specimens are also diffusion treated in a Muffle furnace at 550°C for 4 h to produce diffused specimens of SS 316L.Microstructural examination shows the formation of flat coating/substrate interface due to Si addition.EDS analysis confirms the formation of complex intermetallic at the coating/substrate interface which finally results in increasing the hardness and corrosion resistance properties of coating.
基金support by the project entitled"Interdisciplinarity in Materials Science and Joining Technologies"from the Department of Production Engineering,Faculty of Technical Sciences Novi Sad,Serbia。
文摘Intermetallic aluminide compounds possess several potential advantages compared to alloyed steels,like enhanced oxidation resistance,lower density and the omittance of critical raw materials.Iron aluminides,compared to other transition metal-aluminides of TM_(3)-Al type,although having a higher density compared to titan-aluminides,have a lower density compared to nickel-aluminides,but also a higher ductility than both alternatives,making this material potentially effective in ballistic protection application.Density-wise,this material may be a worthy alternative to armour steels,which was the aim of this study.Two materials,Fe_(3)Al intermetallic compound(F3A-C)and Armox 500 armour steel were ballistically tested against tungsten-carbide(WC)armour-piercing ammunition,in accordance with STANAG 4569.After ballistic testing,microhardness and metallographic testing were performed,revealing differences in strain hardening,crack propagation mode and exit hole morphology.F3A-C ballistic resistance is similar to that of armour steel,in spite of the lower tensile and impact mechanical properties,relying on a considerably higher strain hardening rate,thermal properties and a lower density.
文摘A new process was used for producing FeAl alloy pow de rs with double consumable rotating electrodes and the powders made in this appar atus were analyzed. In this new technology, tungsten rod serves as a cathode ele ctrode, while the alloy rod as an anode electrode. The conventional rotating ele ctrode process must have an anode with pre-melting alloys; however, in this new process, using pure iron as cathode electrode and pure aluminum as anode electr ode can eliminate the step of pre-melting. The effects of process variables, which include electrode rotational speed, a nd electrode diameter of the mean particle diameter were determined. Results showed that both the rotational speed and diameter of electrodes would a ffect the mean diameter of particles. There are three kinds of powders with diff erent composition produced in this study and the possible mechanisms are discuss ed. The process parameters and volume mean diameter of the powders have been cor related to find an experimental equation. The results show that when the rotational speed and the diameter of the anode el ectrode are increased, the powders size will decrease. However, the powders size will increase with cathode electrode.
文摘The present work explores the feasibility of fabricating porous 3D parts in TiAl intermetallic alloy directly from Tie6Ale4V and Al powders. This approach uses a binder jetting additive manufacturing process followed by reactive sintering. The results demonstrate that the present approach is successful for realizing parts in TiAl intermetallic alloy.
文摘The structure and characteristics of dislocation networks in Ti50 Al ordered alloy deformed at room temperature were studied by means of TEM diffraction contrast analysis technique. The results show that the observed dislocation networks consist of three
基金The authors gratefully acknowledge the financial support from National Natural Science Foundation of China(No.11602230)the Program for Innovative Research Team in Science and Technology in the University of Henan Province(No.18IRTSTHN015)Key Scientific Projects of University in Henan Province(20B430021).
文摘The Al3Ti compound has potential application in the high temperature structure materials due to its low density,high strength and stiffness.The mechanical behaviors of the material under different loading rates were studied using compression tests.The results indicate that Al3Ti is a typical brittle material and its compressive strength is dependent on the strain rate.Therefore,a series of rate-dependent constitutive equations are needed to describe its mechanical behaviors accurately.However,it is still short of professional research on the material model for Al3Ti.In this study,the mate rial model was developed on the basis of JH-2 constitutive equations using the experimental data.The model was then applied in simulating the impact process of Ti/Al3Ti metal-intermetallic laminate composites so as to validate the established model.Good agreement between simulation and experiment results shows the constitutive model predict the material responses under high rate and large deformation accurately.This work provides more support for the theoretical and numerical research on the intermetallic.
