While pre-deformation is often conducted before aging treatment to increase the strength and microhardness of 2195 Al-Li alloy, it often increases the fatigue crack growth(FCG) rate and thus reduces the fatigue life o...While pre-deformation is often conducted before aging treatment to increase the strength and microhardness of 2195 Al-Li alloy, it often increases the fatigue crack growth(FCG) rate and thus reduces the fatigue life of the alloy.To determine the effects and causes of pre-deformation and heat treatment on the mechanical properties and FCG rate of2195 Al-Li alloy, and to provide a suitable calculation model for the FCG rate under different pre-deformation conditions, 2195 Al-Li alloy specimens with different degrees of pre-rolling(0, 3%, 6%, and 9%) were investigated. The experimental results indicate that with the increase of pre-rolling, the density of the T1phase and the uniformity of the S′distribution and the microhardness, tensile strength, and yield strength of the alloy increase and at the same time the FCG rate increases, and thus the fatigue life is reduced. It was also found that the normalized stress intensity factor of elastic modulus(E) can be applied to correlate the FCG rate of pre-rolled 2195 Al-Li alloy with constant C and K parameters.展开更多
The corrosion properties of aluminum-lithium(Al-Li) alloys, which are potential materials used to construct for tanks of liquid rockets or missiles, are essential for safe propellant storage and transport. In order to...The corrosion properties of aluminum-lithium(Al-Li) alloys, which are potential materials used to construct for tanks of liquid rockets or missiles, are essential for safe propellant storage and transport. In order to manifest the corrosion resistance of the 2195 Al-Li alloy in practical propellant tanks filled with N2O4, the alloy was soaked in 30% nitric acid solution, an accelerating corrosion environment, to test its corrosion behavior. Scanning electron microscopy(SEM) and transmission electron microscopy(TEM)were used to characterize microstructure and corrosion morphology of the alloy. Focused ion beam(FIB),combined with SEM, was used to demonstrate localized corrosion features and the propagation of corrosion pathways beneath the alloy surface. It was found that the corrosion network was formed with most intergranular corrosion and sparse intragranular corrosion. Additionally, the distribution and number of intermetallic particles influenced the localized corrosion degree and the direction of corrosion pathways. Aggregated particles made corrosion pathways continuously and caused more severe corrosion. The results from this work were valid and useful to corrosion prevention and protection for storage safety on propellant tanks in N_(2)O_(4).展开更多
Fine-grained 01420 Al-Li alloy sheets were produced by thermo-mechanical processing based on the mechanism of particle stimulated nucleation of recrystallization.The thermo-mechanically processed sheets were observed ...Fine-grained 01420 Al-Li alloy sheets were produced by thermo-mechanical processing based on the mechanism of particle stimulated nucleation of recrystallization.The thermo-mechanically processed sheets were observed to contain layers of different microstructures along the thickness.The precipitate behavior of the second phase particles and their effects on the distribution of dislocations and layered recrystallized grain structure were analyzed by optical microscopy(OM),scanning electron microscopy(SEM),transmission electron microscopy(TEM) and X-ray diffractometry(XRD).The formation mechanism of the gradient particles was discussed.The results show that after aging,a gradient distribution of large particles along the thickness is observed,the particles in the surface layer(SL) are distributed homogeneously,whereas those in the center layer(CL) are mainly distributed parallel to the rolling direction,and the volume fraction of the particles in the SL is higher than that in the CL.Subsequent rolling in the presence of layer-distributed particles results in a corresponding homogeneous distribution of highly strained regions in the SL and a banded distribution of them in CL,which is the main reason for the formation of layered grain structure along the thickness in the sheets.展开更多
True stress-true strain curve,microstructure and texture information were obtained to investigate the superplastic deformation behavior of 1420 Al-Li alloy sheets with initial elongated grains.From the true stress-tru...True stress-true strain curve,microstructure and texture information were obtained to investigate the superplastic deformation behavior of 1420 Al-Li alloy sheets with initial elongated grains.From the true stress-true curve,the stress increases with the increase of strain to 0.15,then dramatically decreases with the increase of strain to 0.80,and finally keeps almost a horizontal line.Meanwhile,initial elongated grains are gradually changed into equiaxed grains and the initial strong Brass {0 1 1} <2 1 1> and S {1 2 3} <6 3 4> orientations are turned into nearly random orientation with increasing strain.All these results suggest that dislocation activity is the dominant mechanism during the first stage,then dynamic recrystallization occurs,and grain rotation is expected as an accommodation for grain boundary sliding(GBS).At larger strains,grain boundary migration(GBM) becomes necessary to accommodate GBS.展开更多
The ocean is one of the essential fields of national defense in the future,and more and more attention is paid to the lightweight research of Marine equipment and materials.This study it is to develop a Machine learni...The ocean is one of the essential fields of national defense in the future,and more and more attention is paid to the lightweight research of Marine equipment and materials.This study it is to develop a Machine learning(ML)-based prediction method to study the evolution of the mechanical properties of Al-Li alloys in the marine environment.We obtained the mechanical properties of Al-Li alloy samples under uniaxial tensile deformation at different exposure times through Marine exposure experiments.We obtained the strain evolution by digital image correlation(DIC).The strain field images are voxelized using 2D-Convolutional Neural Networks(CNN)autoencoders as input data for Long Short-Term Memory(LSTM)neural networks.Then,the output data of LSTM neural networks combined with corrosion features were input into the Back Propagation(BP)neural network to predict the mechanical properties of Al-Li alloys.The main conclusions are as follows:1.The variation law of mechanical properties of2297-T8 in the Marine atmosphere is revealed.With the increase in outdoor exposure test time,the tensile elastic model of 2297-T8 changes slowly,within 10%,and the tensile yield stress changes significantly,with a maximum attenuation of 23.6%.2.The prediction model can predict the strain evolution and mechanical response simultaneously with an error of less than 5%.3.This study shows that a CNN/LSTM system based on machine learning can be built to capture the corrosion characteristics of Marine exposure experiments.The results show that the relationship between corrosion characteristics and mechanical response can be predicted without considering the microstructure evolution of metal materials.展开更多
The yield strength or critical resolved stress （CRSS） of alloys 2090 and 2090+Ce were examined as a function of sheet orientation, with specific emphasis on the role of precipitation in the variation of anisotropy. ...The yield strength or critical resolved stress （CRSS） of alloys 2090 and 2090+Ce were examined as a function of sheet orientation, with specific emphasis on the role of precipitation in the variation of anisotropy. The three heat treatments （solution, peak aging and reversion after peak aging） were used in order to identify the contribution of precipitates T1, δ′and θ′ to CRSS. The results show that the strengthening contribution of T1 phase is greatly different at various orientations with respect to rolling direction, by comparing with the co-strengthening effect of δ′and θ′ phases. The precipitation of T1 phase can weaken the anisotropy of mechanical properties. The peak aged and reverted specimens have a stronger tendency of delaminating along grain boundary, which may be a direct reason for the decrease of anisotropic yield strength. This is correlated with the precipitation of T1 phase at subgain boundaries.展开更多
Creep age forming techniques have been widely used in aerospace industries. In this study, we investigated the effect of aging temperature(143 °C-163 °C) on the creep behavior of Al-Li-S4 aluminum alloy and ...Creep age forming techniques have been widely used in aerospace industries. In this study, we investigated the effect of aging temperature(143 °C-163 °C) on the creep behavior of Al-Li-S4 aluminum alloy and their mechanical properties at room temperature. The mechanical properties were tested by tensile testing, and the microstructural evolution at different aging temperatures was examined by transmission electron microscopy. Results show that the creep strains and the room-temperature mechanical properties after creep aging increase with the aging temperature. As the aging temperature increases, the creep strain increases from 0.018% at 143 °C to 0.058% at 153 °C, and then to 0.094% at 163 °C. Within 25 h aging, the number of creep steps increases and the duration time of the same steps is shortened with the growth of aging temperatures. Therefore, the increase in aging temperatures accelerates the progress of the entire creep. Two main strengthening precipitates θ′(Al2 Cu) and T1(Al2 Cu Li) phases were characterized. This work indicates that the creep strain and mechanical properties of Al-Li-S4 alloys can be improved by controlling aging temperatures.展开更多
Mechanical properties and microstructures of Al-Li-Cu-Mg-Ag alloy after solution treatments were investigated by means of optical microscopy （OM）, tensile test, hardness measurement and electrical conductivity test,...Mechanical properties and microstructures of Al-Li-Cu-Mg-Ag alloy after solution treatments were investigated by means of optical microscopy （OM）, tensile test, hardness measurement and electrical conductivity test, differential scanning calorimetric （DSC）, energy dispersive X-ray （EDX）, scanning electron microscopy （SEM） and transition electron microscopy （TEM）, respectively The results show that both tensile strength and hardness increase first and then decrease with temperature at constant holding time of 30 min with maximum strength and hardness appearing at 520 ℃. Tensile strength, hardness and elongation of samples treated at 520 ℃ for 30 min are 566 MPa （σb）, 512 MPa （σ0.2）, HB 148 and 8.23% （δ）, respectively. There are certain amount of fine T1 （AI2CuLi） phase dispersing among AI substrates according to TEM images. This may result in mixed fracture morphology with trans-granular and inter-granular delamination cracks observed in SEM images.展开更多
Titanium alloy has the advantages of high strength,strong corrosion resistance,excellent high and low temperature mechanical properties,etc.,and is widely used in aerospace,shipbuilding,weapons and equipment,and other...Titanium alloy has the advantages of high strength,strong corrosion resistance,excellent high and low temperature mechanical properties,etc.,and is widely used in aerospace,shipbuilding,weapons and equipment,and other fields.In recent years,with the continuous increase in demand for medium-thick plate titanium alloys,corresponding welding technologies have also continued to develop.Therefore,this article reviews the research progress of deep penetration welding technology for medium-thick plate titanium alloys,mainly covering traditional arc welding,high-energy beam welding,and other welding technologies.Among many methods,narrow gap welding,hybrid welding,and external energy field assistance welding all contribute to improving the welding efficiency and quality of medium-thick plate titanium alloys.Finally,the development trend of deep penetration welding technology for mediumthick plate titanium alloys is prospected.展开更多
The effects of different warm rolling(WR)reductions on the microstructure and mechanical properties of low-Cr FeCrAl alloys at both room and elevated temperatures were investigated.The study revealed that when the WR ...The effects of different warm rolling(WR)reductions on the microstructure and mechanical properties of low-Cr FeCrAl alloys at both room and elevated temperatures were investigated.The study revealed that when the WR reduction is small,it effectively refines the grains and forms a large number of subgrains in the matrix,while also inducing the dissolution of the Laves phase.This enhances the mechanical properties of FeCrAl alloys primarily through grain refinement and solid solution strengthening.Conversely,with larger WR reductions,the grain refinement effect diminishes,but a significant number of Laves phases form in the matrix,strengthening the alloys primarily through precipitation strengthening.WR exhibited a remarkable enhancing effect on the comprehensive mechanical properties at both room and high temperatures,with a signi-ficant enhancement in ductility at high temperatures.Notably,a 10%WR reduction resulted in the optimal overall mechanical properties at both room and elevated temperatures.展开更多
High-Entropy Alloys(HEAs)exhibit significant potential across multiple domains due to their unique properties.However,conventional research methodologies face limitations in composition design,property prediction,and ...High-Entropy Alloys(HEAs)exhibit significant potential across multiple domains due to their unique properties.However,conventional research methodologies face limitations in composition design,property prediction,and process optimization,characterized by low efficiency and high costs.The integration of Artificial Intelligence(AI)technologies has provided innovative solutions for HEAs research.This review presented a detailed overview of recent advancements in AI applications for structural modeling and mechanical property prediction of HEAs.Furthermore,it discussed the advantages of big data analytics in facilitating alloy composition design and screening,quality control,and defect prediction,as well as the construction and sharing of specialized material databases.The paper also addressed the existing challenges in current AI-driven HEAs research,including issues related to data quality,model interpretability,and cross-domain knowledge integration.Additionally,it proposed prospects for the synergistic development of AI-enhanced computational materials science and experimental validation systems.展开更多
Al-Cu-Mg-Ag alloys have become a research hotspot because of its good heat resistance.Its excellent mechanical properties are inseparable from the regulation of the structure by researchers.The method of material stru...Al-Cu-Mg-Ag alloys have become a research hotspot because of its good heat resistance.Its excellent mechanical properties are inseparable from the regulation of the structure by researchers.The method of material structure simulation has become more and more perfect.This study employs numerical simulation to investigate the microstructure evolution of Al-Cu-Mg-Ag alloys during solidification with the aim of controlling its structure.The size distribution of Ti-containing particles in an Al-Ti-B master alloy was characterized via microstructure observation,serving as a basis for optimizing the nucleation density parameters for particles of varying radii in the phase field model.The addition of refiner inhibited the growth of dendrites and no longer produced coarse dendrites.With the increase of refiner,the grains gradually tended to form cellular morphology.The refined grains were about 100μm in size.Experimental validation of the simulated as-cast grain morphology was conducted.The samples were observed by metallographic microscope and scanning electron microscope.The addition of refiner had a significant effect on the refinement of the alloy,and the average grain size after refinement was also about 100μm.At the same time,the XRD phase identification of the alloy was carried out.The observation of the microstructure morphology under the scanning electron microscope showed that the precipitated phase was mainly concentrated on the grain boundary.The Al_(2)Cu accounted for about 5%,and the matrix phase FCC accounted for about 95%,which also corresponded well with the simulation results.展开更多
The utilization of nickel-based catalysts as alternatives to expensive platinum-based(Pt-based)materials for the hydrogen evolution reaction in acidic electrolytes has attracted considerable attention due to their pot...The utilization of nickel-based catalysts as alternatives to expensive platinum-based(Pt-based)materials for the hydrogen evolution reaction in acidic electrolytes has attracted considerable attention due to their potential for enabling cost-effective industrial applications.However,the unsatisfied cyclic stability and electrochemical activity limit their further application.In this work,nickel-molybdenum(Ni-Mo)alloy catalysts were successfully synthesized through a comprehensive process including electrodeposition,thermal annealing,and electrochemical activation.Owing to the synergistic interaction of molybdenum trinickelide(Ni_(3)Mo)and molybdenum dioxide(MoO_(2))in Ni-Mo alloy,the catalyst display superior overall electrochemical properties.A low overpotential of 86 mV at 10 mA/cm^(2)and a Tafel slope of 74.0 mV/dec in 0.5 mol/L H_(2)SO_(4)solution can be achieved.Notably,remarkable stability with negligible performance degradation even after 100 h could be maintained.This work presents a novel and effective strategy for the design and fabrication of high-performance,non-precious metal electrocatalysts for acidic water electrolysis.展开更多
High-entropy alloys(HEAs)have become essential materials in the aerospace and defense industries due to their remarkable mechanical properties,which include wear resistance,fatigue endurance,and corrosion resistance.T...High-entropy alloys(HEAs)have become essential materials in the aerospace and defense industries due to their remarkable mechanical properties,which include wear resistance,fatigue endurance,and corrosion resistance.The welding of high-entropy alloys is a cutting-edge field of study that is attracting a lot of interest and investigation from research organizations and businesses.Welding defects including porosity and cracks are challenging problem and limit the development of welding HEAs.This paper provides a comprehensive review of research on weldability of HEAs and the application of diverse welding techniques on welding HEAs over recent years.The forming mechanism and control strategies of defects during welding HEAs were provided in this work.Various welding techniques,including arc welding,laser welding,electron beam welding,friction stir welding,diffusion bonding and explosive welding,have been extensively investigated and applied to improve the microstructure and mechanical properties of HEAs joints.Furthermore,an in-depth review of the microstructure and mechanical properties of HEAs joints obtained by various welding methods is presented.This paper concludes with a discussion of the potential challenges associated with high-entropy alloy welding,thus providing valuable insights for future research efforts in this area.展开更多
To weaken the basal texture and in-plane anisotropy of magnesium alloy, non-basal slips are pre-enhanced by pre-rolling with a single pass larger strain reduction at elevated temperatures. Then Mg alloy sheets with th...To weaken the basal texture and in-plane anisotropy of magnesium alloy, non-basal slips are pre-enhanced by pre-rolling with a single pass larger strain reduction at elevated temperatures. Then Mg alloy sheets with the thickness of 1 mm are achieved after five passes rolling at 300 ℃. A double peak and disperse basal texture is generated after pre- rolling at higher temperatures when the non-basal slips are more active. So, the texture intensity of pre-rolled samples is reduced. Moreover, the distribution condition of in-grain misorientation axes (a method to analyze the activation of slips) shows that the pyramidal slip is quite active during deformation. After annealing on final rolled sheets, the texture distributions are changed and the intensity of texture reduces obviously due to static recrystallization. In particular, the r-value and in-plane anisotropy of pre-rolled samples are obviously lower than those of sample without pre-rolling.展开更多
The effects of pre-compression and pre-aging on the age-hardening response and microstructure of Mg-9.8Sn3.0 Zn(wt.%)alloy have been investigated via hardness test and advanced electron microscopy.The alloy subjected ...The effects of pre-compression and pre-aging on the age-hardening response and microstructure of Mg-9.8Sn3.0 Zn(wt.%)alloy have been investigated via hardness test and advanced electron microscopy.The alloy subjected to both pre-compression and pre-aging exhibits the most refined and densest distribution of precipitates upon aging at 200℃,leading to the superior age-hardening performance observed in the alloy.Comparatively,the alloy that underwent only pre-aging displayed a greater number density of precipitates than its counterpart that was neither pre-compressed nor pre-aged when both were aged to their peak conditions at 200℃,indicating an enhanced age-hardening response in the pre-aged alloy.The precipitates in these three peak-aged alloys consist of Mg_(2)Sn and MgZn_(2)phases.The reason why the pre-aged alloy has a higher number density of precipitates than the directly aged alloy is that MgZn_(2)phase formed during pre-aging can serve as heterogeneous nucleation site for the formation of Mg_(2)Sn.The reason why the pre compression and pre-aged alloy has the highest number density of precipitates is that Mg_(3)Sn and MgZn_(2)phases formed during pre-aging,alongside lattice defects introduced during pre-compression,collectively act as effective heterogeneous nucleation sites for the formation of Mg_(2)Sn during the subsequent aging at 200℃.展开更多
The microstructure,fracture mechanisms,deformation modes,and their correlation with the mechanical properties of Mg-Zn-Gd alloys were analyzed,considering the influence of Y and Nd additions.Increasing Y content and d...The microstructure,fracture mechanisms,deformation modes,and their correlation with the mechanical properties of Mg-Zn-Gd alloys were analyzed,considering the influence of Y and Nd additions.Increasing Y content and decreasing Nd content resulted in an increase in grain size from 17.2 to 29.2μm,and two types of LPSO phases,14 H and 18 R,formed in the alloy.The mechanical properties of the alloys were predominantly influenced by the LPSO phase,with the grain size effect being relatively minor.Based on this analysis,higher Y and lower Nd contents enhanced the tensile strength,yield strength,and elongation of the alloys,with additional improvements observed following solid solution treatment.Changes in Y and Nd content caused a shift in fracture patterns,transitioning from ductile fracture to brittle fracture and then to mixed fracture.Following solid solution treatment,the alloy progressively transitions from intergranular to a combination of ductile and deconvolutional fracture.The deformation modes observed at each stage are as follows:an increase in LPSO phases and twins activates pyramidal slip and suppresses prismatic slip.展开更多
The pronounced anisotropy in mechanical properties presents a major obstacle to the extensive application of aluminum-lithium(Al-Li)alloys,primarily attributed to heterogeneous precipitate distribution,grain structure...The pronounced anisotropy in mechanical properties presents a major obstacle to the extensive application of aluminum-lithium(Al-Li)alloys,primarily attributed to heterogeneous precipitate distribution,grain structure variations,and crystallographic texture.This study investigates the impact of pre-thermal treatment prior to hot rolling and aging treatment on the anisotropy of mechanical properties of 2195 alloy sheet fabricated by gas atomization,hot pressing and hot rolling.The results demonstrate that pre-treatment at 450℃for 4 h promotes finer and more uniform distribution of precipitates,effectively mitigating mechanical anisotropy of the alloy sheet.Additionally,this treatment facilitates recrystallization during hot rolling,further reducing mechanical anisotropy.The in-plane anisotropy(IPA)factors for ultimate tensile strength(UTS)and yield strength(YS)are 1.15%and 0.77%,respectively.Subsequent aging treatment enhances grain refinement and the uniformity of the T_(1) phase,suppresses the formation of precipitation-free zones(PFZs),significantly improving the strength and toughness of the alloy sheet.After peak aging at 165℃for 48 h,the alloy sheet exhibits YS of 547 MPa,UTS of 590 MPa,and elongation(EL)of 7.7%.展开更多
Microstructure and mechanical properties of aged Mg-10Gd-2Y-0.4Zr-0.4Ag alloy sheets prepared by different rolling routes were investigated.The results showed that the cross rolling aged(CRA)sheet possesses larger gra...Microstructure and mechanical properties of aged Mg-10Gd-2Y-0.4Zr-0.4Ag alloy sheets prepared by different rolling routes were investigated.The results showed that the cross rolling aged(CRA)sheet possesses larger grain size than unidirectional rolling aged(URA)sheet due to the occurrence of dynamic recovery during rolling which reduces the dislocation density and delays dynamic recrystallization(DRX).The URA sheet has basal texture and RD favored texture while CRA sheet has multiple-peak texture.Both sheets precipitate β'phase and CRA sheet exhibits a stronger aging response.The CRA sheet has higher yield strength and tensile strength than URA sheet,with reduced yield strength anisotropy but increased tensile strength anisotropy.Taking into account different strengthening mechanisms,although the finer grain size of URA sheet enhances grain boundary strengthening,CRA sheet is more responsive to aging,leading to superior aging-precipitated phase strengthening and consequently higher yield strength.展开更多
The microstructures,mechanical properties,and fracture behaviors of an Al-5.9Zn-1.9Mg alloy subjected to thermomechanical treatment across different pre-rolling temperatures have been exhaustively investigated in pres...The microstructures,mechanical properties,and fracture behaviors of an Al-5.9Zn-1.9Mg alloy subjected to thermomechanical treatment across different pre-rolling temperatures have been exhaustively investigated in present work.The pre-deformation temperature exerts a modest influence on grain morphology,while it profoundly impacts the dislocation configurations and precipitation behaviors.Elevating the rolling temperature from ambient to 170℃results in a reduction in dislocation density within grains accompanied by a notable enhancement in their distributional uniformity.While advancing the temperature to 320℃prompts the premature formation of precipitates during deformation,which diminishes the precipitation during the subsequent ageing.Tensile results reveal that the thermomechanical treatment incorporating pre-rolling at 170℃confers a substantial strengthening effect on the alloy on the basis of both grain boundary strengthening and dislocation strengthening stemmed from pre-deformation along with the precipitation strengthening generated by ageing.Furthermore,the microstructure exhibits a relatively scarce presence of inhomogeneous features such as dislocation pile-ups and micro shear bands,contributing favorably to enhance the ductility of the alloy that presents the mixture of cleavage fracture and dimple-induced failure.展开更多
基金Project(U21A20132) supported by the National Natural Science Foundation of ChinaProject(Gui Renzi2019(13))supported by the Guangxi Specially-invited Experts Foundation of Guangxi Zhuang Autonomous Region,China。
文摘While pre-deformation is often conducted before aging treatment to increase the strength and microhardness of 2195 Al-Li alloy, it often increases the fatigue crack growth(FCG) rate and thus reduces the fatigue life of the alloy.To determine the effects and causes of pre-deformation and heat treatment on the mechanical properties and FCG rate of2195 Al-Li alloy, and to provide a suitable calculation model for the FCG rate under different pre-deformation conditions, 2195 Al-Li alloy specimens with different degrees of pre-rolling(0, 3%, 6%, and 9%) were investigated. The experimental results indicate that with the increase of pre-rolling, the density of the T1phase and the uniformity of the S′distribution and the microhardness, tensile strength, and yield strength of the alloy increase and at the same time the FCG rate increases, and thus the fatigue life is reduced. It was also found that the normalized stress intensity factor of elastic modulus(E) can be applied to correlate the FCG rate of pre-rolled 2195 Al-Li alloy with constant C and K parameters.
基金National Natural Science Foundation of China (Grant No.52075541)Shaanxi Province Natural Science Foundation (Grant No. 2022JM-243) to provide fund for conducting experiments。
文摘The corrosion properties of aluminum-lithium(Al-Li) alloys, which are potential materials used to construct for tanks of liquid rockets or missiles, are essential for safe propellant storage and transport. In order to manifest the corrosion resistance of the 2195 Al-Li alloy in practical propellant tanks filled with N2O4, the alloy was soaked in 30% nitric acid solution, an accelerating corrosion environment, to test its corrosion behavior. Scanning electron microscopy(SEM) and transmission electron microscopy(TEM)were used to characterize microstructure and corrosion morphology of the alloy. Focused ion beam(FIB),combined with SEM, was used to demonstrate localized corrosion features and the propagation of corrosion pathways beneath the alloy surface. It was found that the corrosion network was formed with most intergranular corrosion and sparse intragranular corrosion. Additionally, the distribution and number of intermetallic particles influenced the localized corrosion degree and the direction of corrosion pathways. Aggregated particles made corrosion pathways continuously and caused more severe corrosion. The results from this work were valid and useful to corrosion prevention and protection for storage safety on propellant tanks in N_(2)O_(4).
基金Project(2006DFA53250) supported by the International Science and Technology Cooperation Program of ChinaProject(2005CB623706) supported by the Major State Basic Research Development Program of China
文摘Fine-grained 01420 Al-Li alloy sheets were produced by thermo-mechanical processing based on the mechanism of particle stimulated nucleation of recrystallization.The thermo-mechanically processed sheets were observed to contain layers of different microstructures along the thickness.The precipitate behavior of the second phase particles and their effects on the distribution of dislocations and layered recrystallized grain structure were analyzed by optical microscopy(OM),scanning electron microscopy(SEM),transmission electron microscopy(TEM) and X-ray diffractometry(XRD).The formation mechanism of the gradient particles was discussed.The results show that after aging,a gradient distribution of large particles along the thickness is observed,the particles in the surface layer(SL) are distributed homogeneously,whereas those in the center layer(CL) are mainly distributed parallel to the rolling direction,and the volume fraction of the particles in the SL is higher than that in the CL.Subsequent rolling in the presence of layer-distributed particles results in a corresponding homogeneous distribution of highly strained regions in the SL and a banded distribution of them in CL,which is the main reason for the formation of layered grain structure along the thickness in the sheets.
基金Project(2006DFA53250) supported by the International Science and Technology Cooperation Program of ChinaProject(2005CB623706) supported by the National Basic Research Program of China
文摘True stress-true strain curve,microstructure and texture information were obtained to investigate the superplastic deformation behavior of 1420 Al-Li alloy sheets with initial elongated grains.From the true stress-true curve,the stress increases with the increase of strain to 0.15,then dramatically decreases with the increase of strain to 0.80,and finally keeps almost a horizontal line.Meanwhile,initial elongated grains are gradually changed into equiaxed grains and the initial strong Brass {0 1 1} <2 1 1> and S {1 2 3} <6 3 4> orientations are turned into nearly random orientation with increasing strain.All these results suggest that dislocation activity is the dominant mechanism during the first stage,then dynamic recrystallization occurs,and grain rotation is expected as an accommodation for grain boundary sliding(GBS).At larger strains,grain boundary migration(GBM) becomes necessary to accommodate GBS.
基金supported by the Southwest Institute of Technology and Engineering cooperation fund(Grant No.HDHDW5902020104)。
文摘The ocean is one of the essential fields of national defense in the future,and more and more attention is paid to the lightweight research of Marine equipment and materials.This study it is to develop a Machine learning(ML)-based prediction method to study the evolution of the mechanical properties of Al-Li alloys in the marine environment.We obtained the mechanical properties of Al-Li alloy samples under uniaxial tensile deformation at different exposure times through Marine exposure experiments.We obtained the strain evolution by digital image correlation(DIC).The strain field images are voxelized using 2D-Convolutional Neural Networks(CNN)autoencoders as input data for Long Short-Term Memory(LSTM)neural networks.Then,the output data of LSTM neural networks combined with corrosion features were input into the Back Propagation(BP)neural network to predict the mechanical properties of Al-Li alloys.The main conclusions are as follows:1.The variation law of mechanical properties of2297-T8 in the Marine atmosphere is revealed.With the increase in outdoor exposure test time,the tensile elastic model of 2297-T8 changes slowly,within 10%,and the tensile yield stress changes significantly,with a maximum attenuation of 23.6%.2.The prediction model can predict the strain evolution and mechanical response simultaneously with an error of less than 5%.3.This study shows that a CNN/LSTM system based on machine learning can be built to capture the corrosion characteristics of Marine exposure experiments.The results show that the relationship between corrosion characteristics and mechanical response can be predicted without considering the microstructure evolution of metal materials.
文摘The yield strength or critical resolved stress （CRSS） of alloys 2090 and 2090+Ce were examined as a function of sheet orientation, with specific emphasis on the role of precipitation in the variation of anisotropy. The three heat treatments （solution, peak aging and reversion after peak aging） were used in order to identify the contribution of precipitates T1, δ′and θ′ to CRSS. The results show that the strengthening contribution of T1 phase is greatly different at various orientations with respect to rolling direction, by comparing with the co-strengthening effect of δ′and θ′ phases. The precipitation of T1 phase can weaken the anisotropy of mechanical properties. The peak aged and reverted specimens have a stronger tendency of delaminating along grain boundary, which may be a direct reason for the decrease of anisotropic yield strength. This is correlated with the precipitation of T1 phase at subgain boundaries.
基金Project(2017YFB0306300)supported by National key R&D Program of ChinaProject(zzyikt2015-05)supported by the Project of State Key Laboratory of High Performance Complex Manufacture,China。
文摘Creep age forming techniques have been widely used in aerospace industries. In this study, we investigated the effect of aging temperature(143 °C-163 °C) on the creep behavior of Al-Li-S4 aluminum alloy and their mechanical properties at room temperature. The mechanical properties were tested by tensile testing, and the microstructural evolution at different aging temperatures was examined by transmission electron microscopy. Results show that the creep strains and the room-temperature mechanical properties after creep aging increase with the aging temperature. As the aging temperature increases, the creep strain increases from 0.018% at 143 °C to 0.058% at 153 °C, and then to 0.094% at 163 °C. Within 25 h aging, the number of creep steps increases and the duration time of the same steps is shortened with the growth of aging temperatures. Therefore, the increase in aging temperatures accelerates the progress of the entire creep. Two main strengthening precipitates θ′(Al2 Cu) and T1(Al2 Cu Li) phases were characterized. This work indicates that the creep strain and mechanical properties of Al-Li-S4 alloys can be improved by controlling aging temperatures.
基金Foundation item： Project（6140506） supported by GAD （General Armament Department）, China
文摘Mechanical properties and microstructures of Al-Li-Cu-Mg-Ag alloy after solution treatments were investigated by means of optical microscopy （OM）, tensile test, hardness measurement and electrical conductivity test, differential scanning calorimetric （DSC）, energy dispersive X-ray （EDX）, scanning electron microscopy （SEM） and transition electron microscopy （TEM）, respectively The results show that both tensile strength and hardness increase first and then decrease with temperature at constant holding time of 30 min with maximum strength and hardness appearing at 520 ℃. Tensile strength, hardness and elongation of samples treated at 520 ℃ for 30 min are 566 MPa （σb）, 512 MPa （σ0.2）, HB 148 and 8.23% （δ）, respectively. There are certain amount of fine T1 （AI2CuLi） phase dispersing among AI substrates according to TEM images. This may result in mixed fracture morphology with trans-granular and inter-granular delamination cracks observed in SEM images.
基金financially supported by the Key Research and Development Program of Ningbo(Grant No.2023Z098)Natural Science Foundation of Inner Mongolia(Grant No.2023MS05040)+1 种基金Shenyang Collaborative Innovation Center Project for Multiple Energy Fields Composite Processing of Special Materials(Grant No.JG210027)Shenyang Key Technology Special Project of The Open Competition Mechanism to Select the Best Solution(Grant Nos.2022210101000827,2022-0-43-048).
文摘Titanium alloy has the advantages of high strength,strong corrosion resistance,excellent high and low temperature mechanical properties,etc.,and is widely used in aerospace,shipbuilding,weapons and equipment,and other fields.In recent years,with the continuous increase in demand for medium-thick plate titanium alloys,corresponding welding technologies have also continued to develop.Therefore,this article reviews the research progress of deep penetration welding technology for medium-thick plate titanium alloys,mainly covering traditional arc welding,high-energy beam welding,and other welding technologies.Among many methods,narrow gap welding,hybrid welding,and external energy field assistance welding all contribute to improving the welding efficiency and quality of medium-thick plate titanium alloys.Finally,the development trend of deep penetration welding technology for mediumthick plate titanium alloys is prospected.
文摘The effects of different warm rolling(WR)reductions on the microstructure and mechanical properties of low-Cr FeCrAl alloys at both room and elevated temperatures were investigated.The study revealed that when the WR reduction is small,it effectively refines the grains and forms a large number of subgrains in the matrix,while also inducing the dissolution of the Laves phase.This enhances the mechanical properties of FeCrAl alloys primarily through grain refinement and solid solution strengthening.Conversely,with larger WR reductions,the grain refinement effect diminishes,but a significant number of Laves phases form in the matrix,strengthening the alloys primarily through precipitation strengthening.WR exhibited a remarkable enhancing effect on the comprehensive mechanical properties at both room and high temperatures,with a signi-ficant enhancement in ductility at high temperatures.Notably,a 10%WR reduction resulted in the optimal overall mechanical properties at both room and elevated temperatures.
文摘High-Entropy Alloys(HEAs)exhibit significant potential across multiple domains due to their unique properties.However,conventional research methodologies face limitations in composition design,property prediction,and process optimization,characterized by low efficiency and high costs.The integration of Artificial Intelligence(AI)technologies has provided innovative solutions for HEAs research.This review presented a detailed overview of recent advancements in AI applications for structural modeling and mechanical property prediction of HEAs.Furthermore,it discussed the advantages of big data analytics in facilitating alloy composition design and screening,quality control,and defect prediction,as well as the construction and sharing of specialized material databases.The paper also addressed the existing challenges in current AI-driven HEAs research,including issues related to data quality,model interpretability,and cross-domain knowledge integration.Additionally,it proposed prospects for the synergistic development of AI-enhanced computational materials science and experimental validation systems.
文摘Al-Cu-Mg-Ag alloys have become a research hotspot because of its good heat resistance.Its excellent mechanical properties are inseparable from the regulation of the structure by researchers.The method of material structure simulation has become more and more perfect.This study employs numerical simulation to investigate the microstructure evolution of Al-Cu-Mg-Ag alloys during solidification with the aim of controlling its structure.The size distribution of Ti-containing particles in an Al-Ti-B master alloy was characterized via microstructure observation,serving as a basis for optimizing the nucleation density parameters for particles of varying radii in the phase field model.The addition of refiner inhibited the growth of dendrites and no longer produced coarse dendrites.With the increase of refiner,the grains gradually tended to form cellular morphology.The refined grains were about 100μm in size.Experimental validation of the simulated as-cast grain morphology was conducted.The samples were observed by metallographic microscope and scanning electron microscope.The addition of refiner had a significant effect on the refinement of the alloy,and the average grain size after refinement was also about 100μm.At the same time,the XRD phase identification of the alloy was carried out.The observation of the microstructure morphology under the scanning electron microscope showed that the precipitated phase was mainly concentrated on the grain boundary.The Al_(2)Cu accounted for about 5%,and the matrix phase FCC accounted for about 95%,which also corresponded well with the simulation results.
基金supported by the National Natural Science Foundation of China(22179138).
文摘The utilization of nickel-based catalysts as alternatives to expensive platinum-based(Pt-based)materials for the hydrogen evolution reaction in acidic electrolytes has attracted considerable attention due to their potential for enabling cost-effective industrial applications.However,the unsatisfied cyclic stability and electrochemical activity limit their further application.In this work,nickel-molybdenum(Ni-Mo)alloy catalysts were successfully synthesized through a comprehensive process including electrodeposition,thermal annealing,and electrochemical activation.Owing to the synergistic interaction of molybdenum trinickelide(Ni_(3)Mo)and molybdenum dioxide(MoO_(2))in Ni-Mo alloy,the catalyst display superior overall electrochemical properties.A low overpotential of 86 mV at 10 mA/cm^(2)and a Tafel slope of 74.0 mV/dec in 0.5 mol/L H_(2)SO_(4)solution can be achieved.Notably,remarkable stability with negligible performance degradation even after 100 h could be maintained.This work presents a novel and effective strategy for the design and fabrication of high-performance,non-precious metal electrocatalysts for acidic water electrolysis.
基金Project(52105351)supported by the National Natural Science Foundation of ChinaProject(24KJA460002)supported by the Natural Science Foundation of the Higher Education Institutions of Jiangsu Province,ChinaProject(G2023014009L)supported by the High-end Foreign Experts Recruitment Plan of China。
文摘High-entropy alloys(HEAs)have become essential materials in the aerospace and defense industries due to their remarkable mechanical properties,which include wear resistance,fatigue endurance,and corrosion resistance.The welding of high-entropy alloys is a cutting-edge field of study that is attracting a lot of interest and investigation from research organizations and businesses.Welding defects including porosity and cracks are challenging problem and limit the development of welding HEAs.This paper provides a comprehensive review of research on weldability of HEAs and the application of diverse welding techniques on welding HEAs over recent years.The forming mechanism and control strategies of defects during welding HEAs were provided in this work.Various welding techniques,including arc welding,laser welding,electron beam welding,friction stir welding,diffusion bonding and explosive welding,have been extensively investigated and applied to improve the microstructure and mechanical properties of HEAs joints.Furthermore,an in-depth review of the microstructure and mechanical properties of HEAs joints obtained by various welding methods is presented.This paper concludes with a discussion of the potential challenges associated with high-entropy alloy welding,thus providing valuable insights for future research efforts in this area.
基金Project(52374395) supported by the National Natural Science Foundations of ChinaProjects(20210302123135,20210302123163) supported by the Natural Science Foundation of Shanxi Province,China+2 种基金Projects(YDZJSX20231B003,YDZJSX2021A010) supported by the Central Government Guided Local Science and Technology Development Projects,ChinaProject(2022M710541) supported by the China Postdoctoral Science FoundationProjects(202104021301022,202204021301009) supported by the Scientific and Technological Achievements Transformation Guidance Special Project of Shanxi Province,China。
文摘To weaken the basal texture and in-plane anisotropy of magnesium alloy, non-basal slips are pre-enhanced by pre-rolling with a single pass larger strain reduction at elevated temperatures. Then Mg alloy sheets with the thickness of 1 mm are achieved after five passes rolling at 300 ℃. A double peak and disperse basal texture is generated after pre- rolling at higher temperatures when the non-basal slips are more active. So, the texture intensity of pre-rolled samples is reduced. Moreover, the distribution condition of in-grain misorientation axes (a method to analyze the activation of slips) shows that the pyramidal slip is quite active during deformation. After annealing on final rolled sheets, the texture distributions are changed and the intensity of texture reduces obviously due to static recrystallization. In particular, the r-value and in-plane anisotropy of pre-rolled samples are obviously lower than those of sample without pre-rolling.
基金Project(52101167)supported by the National Natural Science Foundation of ChinaProject(2022JJ40604)supported by the Natural Science Foundation of Hunan Province,ChinaProject(2022ZZTS0538)supported by the Postgraduate Research Innovation Project of Central South University,China。
文摘The effects of pre-compression and pre-aging on the age-hardening response and microstructure of Mg-9.8Sn3.0 Zn(wt.%)alloy have been investigated via hardness test and advanced electron microscopy.The alloy subjected to both pre-compression and pre-aging exhibits the most refined and densest distribution of precipitates upon aging at 200℃,leading to the superior age-hardening performance observed in the alloy.Comparatively,the alloy that underwent only pre-aging displayed a greater number density of precipitates than its counterpart that was neither pre-compressed nor pre-aged when both were aged to their peak conditions at 200℃,indicating an enhanced age-hardening response in the pre-aged alloy.The precipitates in these three peak-aged alloys consist of Mg_(2)Sn and MgZn_(2)phases.The reason why the pre-aged alloy has a higher number density of precipitates than the directly aged alloy is that MgZn_(2)phase formed during pre-aging can serve as heterogeneous nucleation site for the formation of Mg_(2)Sn.The reason why the pre compression and pre-aged alloy has the highest number density of precipitates is that Mg_(3)Sn and MgZn_(2)phases formed during pre-aging,alongside lattice defects introduced during pre-compression,collectively act as effective heterogeneous nucleation sites for the formation of Mg_(2)Sn during the subsequent aging at 200℃.
基金Project(2024QN05053)supported by the Natural Science Foundation of Inner Mongolia,ChinaProjects(U24A20106,51931005,52171048)supported by the National Natural Science Foundation of ChinaProject(2020ZDLGY12-02)supported by the Key Industry Innovation Chain Project of Shaanxi Province,China。
文摘The microstructure,fracture mechanisms,deformation modes,and their correlation with the mechanical properties of Mg-Zn-Gd alloys were analyzed,considering the influence of Y and Nd additions.Increasing Y content and decreasing Nd content resulted in an increase in grain size from 17.2 to 29.2μm,and two types of LPSO phases,14 H and 18 R,formed in the alloy.The mechanical properties of the alloys were predominantly influenced by the LPSO phase,with the grain size effect being relatively minor.Based on this analysis,higher Y and lower Nd contents enhanced the tensile strength,yield strength,and elongation of the alloys,with additional improvements observed following solid solution treatment.Changes in Y and Nd content caused a shift in fracture patterns,transitioning from ductile fracture to brittle fracture and then to mixed fracture.Following solid solution treatment,the alloy progressively transitions from intergranular to a combination of ductile and deconvolutional fracture.The deformation modes observed at each stage are as follows:an increase in LPSO phases and twins activates pyramidal slip and suppresses prismatic slip.
基金Project(52274369)supported by the National Natural Science Foundation of ChinaProject(623020034)supported by the National Key Laboratory of Science and Technology on High-strength Structural Materials,China。
文摘The pronounced anisotropy in mechanical properties presents a major obstacle to the extensive application of aluminum-lithium(Al-Li)alloys,primarily attributed to heterogeneous precipitate distribution,grain structure variations,and crystallographic texture.This study investigates the impact of pre-thermal treatment prior to hot rolling and aging treatment on the anisotropy of mechanical properties of 2195 alloy sheet fabricated by gas atomization,hot pressing and hot rolling.The results demonstrate that pre-treatment at 450℃for 4 h promotes finer and more uniform distribution of precipitates,effectively mitigating mechanical anisotropy of the alloy sheet.Additionally,this treatment facilitates recrystallization during hot rolling,further reducing mechanical anisotropy.The in-plane anisotropy(IPA)factors for ultimate tensile strength(UTS)and yield strength(YS)are 1.15%and 0.77%,respectively.Subsequent aging treatment enhances grain refinement and the uniformity of the T_(1) phase,suppresses the formation of precipitation-free zones(PFZs),significantly improving the strength and toughness of the alloy sheet.After peak aging at 165℃for 48 h,the alloy sheet exhibits YS of 547 MPa,UTS of 590 MPa,and elongation(EL)of 7.7%.
基金Project(2023GK2020)supported by the Key Research and Development Program of Hunan Province,China。
文摘Microstructure and mechanical properties of aged Mg-10Gd-2Y-0.4Zr-0.4Ag alloy sheets prepared by different rolling routes were investigated.The results showed that the cross rolling aged(CRA)sheet possesses larger grain size than unidirectional rolling aged(URA)sheet due to the occurrence of dynamic recovery during rolling which reduces the dislocation density and delays dynamic recrystallization(DRX).The URA sheet has basal texture and RD favored texture while CRA sheet has multiple-peak texture.Both sheets precipitate β'phase and CRA sheet exhibits a stronger aging response.The CRA sheet has higher yield strength and tensile strength than URA sheet,with reduced yield strength anisotropy but increased tensile strength anisotropy.Taking into account different strengthening mechanisms,although the finer grain size of URA sheet enhances grain boundary strengthening,CRA sheet is more responsive to aging,leading to superior aging-precipitated phase strengthening and consequently higher yield strength.
基金Project(ZZYJKT2025-03) supported by the Project of State Key Laboratory of Precision Manufacturing for Extreme Service Performance,Central South University,ChinaProject(2024YFB3411200) supported by the National Key Research and Development Program of China。
文摘The microstructures,mechanical properties,and fracture behaviors of an Al-5.9Zn-1.9Mg alloy subjected to thermomechanical treatment across different pre-rolling temperatures have been exhaustively investigated in present work.The pre-deformation temperature exerts a modest influence on grain morphology,while it profoundly impacts the dislocation configurations and precipitation behaviors.Elevating the rolling temperature from ambient to 170℃results in a reduction in dislocation density within grains accompanied by a notable enhancement in their distributional uniformity.While advancing the temperature to 320℃prompts the premature formation of precipitates during deformation,which diminishes the precipitation during the subsequent ageing.Tensile results reveal that the thermomechanical treatment incorporating pre-rolling at 170℃confers a substantial strengthening effect on the alloy on the basis of both grain boundary strengthening and dislocation strengthening stemmed from pre-deformation along with the precipitation strengthening generated by ageing.Furthermore,the microstructure exhibits a relatively scarce presence of inhomogeneous features such as dislocation pile-ups and micro shear bands,contributing favorably to enhance the ductility of the alloy that presents the mixture of cleavage fracture and dimple-induced failure.
