期刊文献+
共找到8篇文章
< 1 >
每页显示 20 50 100
高效液相色谱法测定苦参碱醇质体温敏凝胶中苦参碱含量 被引量:2
1
作者 黄正德 林如文 刘小平 《医药导报》 CAS 2016年第5期521-523,共3页
目的建立高效液相色谱(HPLC)法测定苦参碱醇质体温敏凝胶中苦参碱含量。方法采用YMC-Pack NH2柱(4.6 mm×150 mm,5μm),以乙腈-乙醇(9∶1)为流动相,流速为0.8 m L·min^(-1),柱温(25±2)℃,检测波长为215 nm。结果苦参碱在1... 目的建立高效液相色谱(HPLC)法测定苦参碱醇质体温敏凝胶中苦参碱含量。方法采用YMC-Pack NH2柱(4.6 mm×150 mm,5μm),以乙腈-乙醇(9∶1)为流动相,流速为0.8 m L·min^(-1),柱温(25±2)℃,检测波长为215 nm。结果苦参碱在1.00~100.00μg·m L^(-1)范围内峰面积与浓度呈良好的线性关系(R2=0.999 2),低、中、高浓度苦参碱平均加样回收率分别为98.16%,98.15%,98.00%,RSD为分别为0.30%,0.69%,0.71%。结论该方法操作简单易行,结果灵敏准确,专属性强,精密度高,稳定性好,重复性好,能够用于苦参碱醇质体温敏凝胶中苦参碱的含量测定。 展开更多
关键词 苦参碱质体温敏 色谱法 高效液相 含量测定
在线阅读 下载PDF
以环氧化合物为凝胶促进剂制备块状氧化铁气凝胶 被引量:13
2
作者 任洪波 张林 +2 位作者 万小波 杜爱明 修鹏 《原子能科学技术》 EI CAS CSCD 北大核心 2007年第3期288-291,共4页
以无机铁盐FeCl3为前驱体,环氧丙烷及其衍生物作为凝胶促进剂,采用溶胶-凝胶工艺制备氧化铁凝胶。以氯化铁的醇溶液为前驱体、环氧化合物为凝胶促进剂,制备氧化铁的醇凝胶,通过C02超临界干燥工艺得到氧化铁气凝胶。用透射电镜(TEM... 以无机铁盐FeCl3为前驱体,环氧丙烷及其衍生物作为凝胶促进剂,采用溶胶-凝胶工艺制备氧化铁凝胶。以氯化铁的醇溶液为前驱体、环氧化合物为凝胶促进剂,制备氧化铁的醇凝胶,通过C02超临界干燥工艺得到氧化铁气凝胶。用透射电镜(TEM)对气凝胶微观结构的表征结果表明,气凝胶样品主要由超细微粒堆积而成。BET和BJH测试结果表明,气凝胶样品平均孔径为9.4~18.3nm,比表面积为430-500m^2/g。 展开更多
关键词 金属氧化物 醇凝胶 超临界干燥 -工艺
在线阅读 下载PDF
块状氧化铁气凝胶制备初步研究 被引量:7
3
作者 任洪波 张林 杜爱明 《原子能科学技术》 EI CAS CSCD 北大核心 2005年第6期513-516,共4页
研究以氯化铁的醇溶液为前驱体、有机路易斯碱为凝胶促进剂,快速制备氧化铁的醇凝胶,再通过CO2超临界干燥工艺得到氧化铁气凝胶。用透射电镜(TEM)对氧化铁气凝胶的微观结构的表征结果表明,气凝胶主要由超细微粒堆积而成。经BET和BJH测试... 研究以氯化铁的醇溶液为前驱体、有机路易斯碱为凝胶促进剂,快速制备氧化铁的醇凝胶,再通过CO2超临界干燥工艺得到氧化铁气凝胶。用透射电镜(TEM)对氧化铁气凝胶的微观结构的表征结果表明,气凝胶主要由超细微粒堆积而成。经BET和BJH测试,气凝胶样品的密度为138 mg/cm3时,孔径为97 nm,孔体积为1.97 cm3/g,比表面积为487 m2/g。XRD研究表明,组成氧化铁气凝胶的晶形结构主要为-βFeOOH。 展开更多
关键词 金属氧化物 醇凝胶 超临界干燥
在线阅读 下载PDF
方形锐钛矿TiO_2纳米晶的合成及表征 被引量:12
4
作者 王海 吴玉 徐柏庆 《高等学校化学学报》 SCIE EI CAS CSCD 北大核心 2005年第4期607-610,共4页
在不添加任何模板剂或形状控制剂的条件下,以TiCl4为前体,经氨水沉淀、乙醇洗涤和超临界干燥(AS制备法)选择性地合成了方形锐钛矿TiO2纳米单晶.热稳定性研究结果表明,当焙烧温度不超过650℃时,方形锐钛矿TiO2纳米晶的表面积、孔容、晶粒... 在不添加任何模板剂或形状控制剂的条件下,以TiCl4为前体,经氨水沉淀、乙醇洗涤和超临界干燥(AS制备法)选择性地合成了方形锐钛矿TiO2纳米单晶.热稳定性研究结果表明,当焙烧温度不超过650℃时,方形锐钛矿TiO2纳米晶的表面积、孔容、晶粒/颗粒尺寸基本保持不变.XRD和拉曼光谱分析表明,方形锐钛矿TiO2纳米晶在800℃下焙烧后仍能保持晶相不变,表现出很强的抗晶相转变能力.但在1000℃焙烧后,样品可以完全转变成金红石相TiO2. 展开更多
关键词 锐钛矿型TiO2 方形纳米晶 形状控制合成 醇凝胶 超临界干燥
在线阅读 下载PDF
纳米锑掺杂氧化锡制备中超临界CO_2干燥的工艺优化及动力学
5
作者 龚圣 程杏安 +3 位作者 周新华 尹国强 程江 王浩波 《化工学报》 EI CAS CSCD 北大核心 2015年第4期1593-1599,共7页
纳米锑掺杂氧化锡(ATO)具有优越的光电性能,在制备过程中前驱体干燥处理至关重要。为掌握ATO前驱体的超临界CO2干燥工艺特性,研究了超临界干燥的时间、温度、压力和CO2流量等工艺参数对纳米ATO粒径、比表面积等的影响,进一步探讨了超... 纳米锑掺杂氧化锡(ATO)具有优越的光电性能,在制备过程中前驱体干燥处理至关重要。为掌握ATO前驱体的超临界CO2干燥工艺特性,研究了超临界干燥的时间、温度、压力和CO2流量等工艺参数对纳米ATO粒径、比表面积等的影响,进一步探讨了超临界CO2流量对干燥动力学的影响规律,并拟合了干燥曲线方程。结果表明:温度35~40℃、压力10~14 MPa、CO2流量1.2~1.8 L·h-1、干燥5~6 h,最终能够获得平均粒径20~30 nm、高比表面积的纳米ATO材料;流量对干燥速率有明显影响,醇分比0.4为干燥速率由恒速转为降速的临界点,醇凝胶干燥动力学方程能够很好地描述ATO醇凝胶干燥工艺过程。研究结果可为湿法制备纳米材料的湿凝胶干燥工业化生产和控制提供参考。 展开更多
关键词 ATO 超临界CO2 醇凝胶 工艺优化 动力学 模型
在线阅读 下载PDF
Preparation and swelling behavior of polyvinyl alcohol physiological saline gel 被引量:2
6
作者 潘育松 熊党生 马如银 《Journal of Central South University of Technology》 EI 2006年第1期27-31,共5页
Polyvinyl alcohol(PVA) physiological saline gel was prepared using physiological saline solution of the polymer by freezing and thawing method. The influences of the concentration of PVA, freezing and thawing cycle ti... Polyvinyl alcohol(PVA) physiological saline gel was prepared using physiological saline solution of the polymer by freezing and thawing method. The influences of the concentration of PVA, freezing and thawing cycle times and solvent swelling media on the swelling properties of PVA saline gel were investigated. The result show that the electrolytical ions have great effect on the swelling behavior of PVA saline gel. The equilibrium swelling ratio of PVA saline gel in aqueous swelling media is larger than that in saline swelling media. Also, the equilibrium swelling ratios of PVA saline gel in aqueous and in saline media decrease with the increase of gel concentration and the increase of freezing and thawing cycle times. The decreasing speed of equilibrium swelling ratio with the increase of freezing and thawing cycle times of PVA gel in distilled water is faster than that in physiological saline. The swelling kinetic equation can sufficiently describe the swelling behavior of PVA physiological saline gel. 展开更多
关键词 freezing and thawing polyvinyl alcohol saline gel swelling behavior
在线阅读 下载PDF
Influence of polyethylene glycol on pore structure and electric double-layer capacitance of carbon xerogel
7
作者 侯朝辉 李新海 +2 位作者 何则强 刘恩辉 邓凌峰 《Journal of Central South University of Technology》 2004年第3期255-260,共6页
Mesoporous polyethylene glycol-resorcinol and formaldehyde(PEG-RF) carbon xerogels were prepared by a new polymer blend method in which PEG-RF mixed organic xerogels were synthesized by blending thermally unstable p... Mesoporous polyethylene glycol-resorcinol and formaldehyde(PEG-RF) carbon xerogels were prepared by a new polymer blend method in which PEG-RF mixed organic xerogels were synthesized by blending thermally unstable polyethylene glycol with organic monomers, resorcinol and formaldehyde and then subjected to pyrolization at 1 000 ℃. The influences of mass ratio of PEG to the theoretical yield of RF xerogel, m(PEG)/m(RF) and the (relative) molecular mass of PEG on the pore structure and electric double layer capacitance(EDLC) performance of PEG-RF carbon xerogels were investigated. The results show that PEG under different conditions leads to the difference of phase separation structure of the polymer blend and thus the change of pore structure of PEG-RF carbon xerogels. Specific surface area and capacity of PEG-RF carbon xerogels in 30% H2SO4 solution can reach (755 m2/g) and 150 F/g, respectively. Their surface can be fully utilized to form electric double layer. However, the pore structure differences of PEG-RF carbon xerogels result in their different EDLC performances. The distributed capacitance effect increases with decreasing the pore size of PEG-RF carbon xerogels. 展开更多
关键词 polymer blend method polyethylene glycol carbon xerogel electric double-layer capacitance
在线阅读 下载PDF
Tensile properties of strain-hardening cementitious composites containing polyvinyl-alcohol fibers hybridized with polypropylene fibers 被引量:5
8
作者 H.R.Pakravan M.Jamshidi 《Journal of Central South University》 SCIE EI CAS CSCD 2018年第1期51-59,共9页
Partially replacing polyvinyl-alcohol(PVA)fibers with polypropylene(PP)fibers in strain-hardening cementitious composites(fiber hybridization)modify certain mechanical properties of these materials.The hybridization b... Partially replacing polyvinyl-alcohol(PVA)fibers with polypropylene(PP)fibers in strain-hardening cementitious composites(fiber hybridization)modify certain mechanical properties of these materials.The hybridization based on the introduction of low-modulus hydrophobic polypropylene fibers improves the ductility and the strain-hardening behavior of the cementitious composites containing polyvinyl-alcohol fibers of different types(PVA-SHCC).Pull-out tests indicate that adding PP fibers increases the energy capacity of the hybrid composite with respect to the material containing only PVA fibers under tensile loading,and PP-fiber geometry(i.e.,section shape and length)is a key factor in enhancing the strain capacity. 展开更多
关键词 polyvinyl-alcohol (PVA) strain-hardening cementitious composite (PVA-SHCC) fiber hybridization
在线阅读 下载PDF
上一页 1 下一页 到第
使用帮助 返回顶部