Thermogravimetric study of rubber compositions （operating glove and catheter） in medical waste was carried out using the thermogravimetric analyser （TGA）,at the heating rate of 20 ℃/min in a stream of N2.The resu...Thermogravimetric study of rubber compositions （operating glove and catheter） in medical waste was carried out using the thermogravimetric analyser （TGA）,at the heating rate of 20 ℃/min in a stream of N2.The results indicate that the decomposition process of operating glove appears an obvious mass loss stage at 250-485 ℃,while catheter has two obvious stages at 240-510 ℃ and 655-800 ℃,respectively; both samples present endothermic pyrolysis reaction; the decomposition of operating glove and the first mass loss stage of catheter are in agreement with natural rubber pyrolysis; the second mass loss stage of catheter corresponds to CaCO3 decomposition.Based on the experimental results,a novel two-step four-reaction model was established to simulate the whole continuous processes,which could more satisfactorily describe and predict the pyrolysis processes of rubber compositions,being more mechanistic and conveniently serving for the engineering.展开更多
The fishtail in head and tail of the slabs was studied during V-H hot rolling process. With the application of ANSYS/LS-DYNA, simulation analysis was used to research this process. The various factors which have a gre...The fishtail in head and tail of the slabs was studied during V-H hot rolling process. With the application of ANSYS/LS-DYNA, simulation analysis was used to research this process. The various factors which have a great influence on fishtail shapes were analysed, such as initial width, initial thickness, radius of the edger roll and horizontal roll, edging draught,horizontal reduction rate, and friction coefficient of the surface. Then the curves that can describe the shapes were obtained. After a certain time of self-learning, the optimized curves were given out. At last, through the fitting of the simulation test results, the math models for the area of fishtail defect changing with the presented factors were received. The experimental results show that the accuracy of the prediction for the fishtail shapes is more than 95%. With the application of the prediction for the fishtail shapes and the area of the fishtail defect, the loss rate of the slab is decreased by about 0.1%.展开更多
A thermodynamics analysis on the leaching process of selenium residue and discussion on the behaviors of aqueous ionic in the leaching process were carried out. Through thermodynamical calculation, the values of AG an...A thermodynamics analysis on the leaching process of selenium residue and discussion on the behaviors of aqueous ionic in the leaching process were carried out. Through thermodynamical calculation, the values of AG and relevant potential expressions were obtained. According to these thermodynamical data, the φ-pH diagrams of Se-H2O system at 298 and 373 K were obtained; Simultaneously, the φ-pH diagrams of SO2-H2O and SO2-Se-H2O systems were drawn at 298 K. With increasing the temperature, the stable regions of HSeO3, SeO2- and SeO2- in the φ-pH diagram of Se-H2O system become gradually large, but the limits of pH in the stable region become gradually small. The stability area of reduction precipitation in the SO2-Se-H2O system was finally determined. The results of oxidization leaching experiments of selenium residue indicate that when the mass ratio of selenium residue to sodium chlorate is 2, the concentration of sulfuric acid is 300 g/L and the residue is agitated for 3 h at leaching temperature of 80 ℃, the leaching rate of selenium could reach 97.76 %. The experimental results conform the calculated results by φ-pH diagram. The selenium reduction precipitation in oxidization-leaching solution was analyzed under the conditions of acidity of 150 g/L, the sodium sulphite concentration of 35 g/L at the reductive temperature of 23 ℃ for 120 min. And this demonstrates the thermodynamics analysis.展开更多
In order to study the bending behavior of aluminum alloy 7050 thick plate during snake hot rolling, several coupled thermo-mechanical finite element(FE) models were established. Effects of different initial thicknesse...In order to study the bending behavior of aluminum alloy 7050 thick plate during snake hot rolling, several coupled thermo-mechanical finite element(FE) models were established. Effects of different initial thicknesses, pass reductions, speed ratios and offset distances on the bending value of the plate were analyzed. ‘Quasi smooth plate' and optimum offset distance were defined and quasi smooth plate could be acquired by adjusting offset distance, and then bending control equation was fitted. The results show that bending value of the plate as well as the extent of the increase grows with the increase of pass reduction and decrease of initial thickness; the bending value firstly increases and then keeps steady with the ascending speed ratio; the bending value can be reduced by enlarging the offset distance. The optimum offset distance varies for different rolling parameters and it is augmented with the increase of pass reduction and speed ratio and the decrease of initial thickness. A proper offset distance for different rolling parameters can be calculated by the bending control equation and this equation can be a guidance to acquire a quasi smooth plate. The FEM results agree well with experimental results.展开更多
基金Project(50378062)supported by the National Natural Science Foundation of ChinaProject(09JCYBJC08100)supported by the Natural Science Foundation of Tianjin Municipality,ChinaProject supported by Key Laboratory Program of the Ministry of Education,China
文摘Thermogravimetric study of rubber compositions （operating glove and catheter） in medical waste was carried out using the thermogravimetric analyser （TGA）,at the heating rate of 20 ℃/min in a stream of N2.The results indicate that the decomposition process of operating glove appears an obvious mass loss stage at 250-485 ℃,while catheter has two obvious stages at 240-510 ℃ and 655-800 ℃,respectively; both samples present endothermic pyrolysis reaction; the decomposition of operating glove and the first mass loss stage of catheter are in agreement with natural rubber pyrolysis; the second mass loss stage of catheter corresponds to CaCO3 decomposition.Based on the experimental results,a novel two-step four-reaction model was established to simulate the whole continuous processes,which could more satisfactorily describe and predict the pyrolysis processes of rubber compositions,being more mechanistic and conveniently serving for the engineering.
基金Project(N100307002)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(61174115)supported by the National Natural Science Foundation of China
文摘The fishtail in head and tail of the slabs was studied during V-H hot rolling process. With the application of ANSYS/LS-DYNA, simulation analysis was used to research this process. The various factors which have a great influence on fishtail shapes were analysed, such as initial width, initial thickness, radius of the edger roll and horizontal roll, edging draught,horizontal reduction rate, and friction coefficient of the surface. Then the curves that can describe the shapes were obtained. After a certain time of self-learning, the optimized curves were given out. At last, through the fitting of the simulation test results, the math models for the area of fishtail defect changing with the presented factors were received. The experimental results show that the accuracy of the prediction for the fishtail shapes is more than 95%. With the application of the prediction for the fishtail shapes and the area of the fishtail defect, the loss rate of the slab is decreased by about 0.1%.
基金Project(51072233) supported by the National Natural Science Foundation of China
文摘A thermodynamics analysis on the leaching process of selenium residue and discussion on the behaviors of aqueous ionic in the leaching process were carried out. Through thermodynamical calculation, the values of AG and relevant potential expressions were obtained. According to these thermodynamical data, the φ-pH diagrams of Se-H2O system at 298 and 373 K were obtained; Simultaneously, the φ-pH diagrams of SO2-H2O and SO2-Se-H2O systems were drawn at 298 K. With increasing the temperature, the stable regions of HSeO3, SeO2- and SeO2- in the φ-pH diagram of Se-H2O system become gradually large, but the limits of pH in the stable region become gradually small. The stability area of reduction precipitation in the SO2-Se-H2O system was finally determined. The results of oxidization leaching experiments of selenium residue indicate that when the mass ratio of selenium residue to sodium chlorate is 2, the concentration of sulfuric acid is 300 g/L and the residue is agitated for 3 h at leaching temperature of 80 ℃, the leaching rate of selenium could reach 97.76 %. The experimental results conform the calculated results by φ-pH diagram. The selenium reduction precipitation in oxidization-leaching solution was analyzed under the conditions of acidity of 150 g/L, the sodium sulphite concentration of 35 g/L at the reductive temperature of 23 ℃ for 120 min. And this demonstrates the thermodynamics analysis.
基金Projects(2012CB619505,2010CB731703)supported by the National Basic Research Program of ChinaProject(CX2013B065)supported by Hunan Provincial Innovation Foundation for Postgraduate,China+1 种基金Project(51405520)supported by the National Natural Science Foundation of ChinaProject(zzyjkt2013-06B)supported by the State Key Laboratory of High Performance Complex Manufacturing(Central South University),China
文摘In order to study the bending behavior of aluminum alloy 7050 thick plate during snake hot rolling, several coupled thermo-mechanical finite element(FE) models were established. Effects of different initial thicknesses, pass reductions, speed ratios and offset distances on the bending value of the plate were analyzed. ‘Quasi smooth plate' and optimum offset distance were defined and quasi smooth plate could be acquired by adjusting offset distance, and then bending control equation was fitted. The results show that bending value of the plate as well as the extent of the increase grows with the increase of pass reduction and decrease of initial thickness; the bending value firstly increases and then keeps steady with the ascending speed ratio; the bending value can be reduced by enlarging the offset distance. The optimum offset distance varies for different rolling parameters and it is augmented with the increase of pass reduction and speed ratio and the decrease of initial thickness. A proper offset distance for different rolling parameters can be calculated by the bending control equation and this equation can be a guidance to acquire a quasi smooth plate. The FEM results agree well with experimental results.
