Ti185 alloy is widely used in key industrial fields such as aerospace due to its excellent mechanical properties.The traditional method of preparing Ti185 alloy will inevitably appear“βfleck”,resulting in the decre...Ti185 alloy is widely used in key industrial fields such as aerospace due to its excellent mechanical properties.The traditional method of preparing Ti185 alloy will inevitably appear“βfleck”,resulting in the decrease of mechanical properties,and the high price of V element limits the wide application of Ti185.In this paper,a low-cost master alloy V-Fe powder is used,a dense block is prepared by spark plasma sintering(SPS)technology,and a high-performance Ti185 alloy is prepared by controlling the sintering parameters.XRD and SEM were used to investigate the phase and microstructure of the samples prepared under different parameters.The compressive strength and friction properties of the directly prepared samples were studied.The samples with a sintering temperature of 1350 ℃ and a holding time of 30 min exhibited the most excellent comprehensive performance,with the highest compressive strength and lowest friction coefficient of 1931.59 MPa and 0.47,respectively.展开更多
The almost completely dense copper was prepared by ultrafine copper powder prepared with both methods of electrolysis and novel water-gas atomization through cold isostatic pressing(CIP)and sintering under atmospheric...The almost completely dense copper was prepared by ultrafine copper powder prepared with both methods of electrolysis and novel water-gas atomization through cold isostatic pressing(CIP)and sintering under atmospheric hydrogen.Fine copper powder possesses the higher sintering driving force,thereby promoting shrinkage and densification during the sintering process.The grain size of sintered samples by electrolytic copper powder is smaller than that prepared by the atomized copper powder,and the twin crystals are particularly prone to forming in the former sintered microstructure due to the raw powder with low oxygen content and high residual stress originating from the CIP process.The relative density of samples by electrolytic and atomized powder at 1000℃ sintering temperature achieves 99.3%and 97.4%,respectively,significantly higher than that of the powder metallurgy copper parts reported in the literature.Correspondingly,the ultimate tensile strength and yield strength of samples by both kinds of copper powder are approximately similar,while the elongation of the sintered sample by the electrolytic powder(60%)is apparently higher than the atomized powder(44%).The superior performance of samples fabricated by electrolytic powder is inferred from the full density and low oxygen level for there is no cuprous oxide in the grain boundaries.展开更多
Similar friction welded joints of AA-7005 aluminum rods were fabricated using different combinations of process parameters such as friction pressure(1.0, 1.5 and 2.0 MPa) and friction time(10, 15 and 20 s). Interfacia...Similar friction welded joints of AA-7005 aluminum rods were fabricated using different combinations of process parameters such as friction pressure(1.0, 1.5 and 2.0 MPa) and friction time(10, 15 and 20 s). Interfacial microstructure and formation of intermetallic compounds at the joint interface were evaluated via scanning electron microscopy(SEM) equipped with energy dispersive spectrum(EDS), and optical microscopy(OM). Microstructural observations reveal the formation of intermetallic phases during the welding process which cannot be extruded from the interface. Theses phases influence the tensile strength of the resultant joints. From the tensile characteristics viewpoint, the greatest tensile strength value of 365 MPa is obtained at 1.5 MPa and 15 s. Finally, the role of microstructural features on tensile strength of resultant joints is discussed.展开更多
基金Projects(51671152,51874225)supported by the National Natural Science Foundation of ChinaProject(2020ZDLGY13-10)supported by Shaanxi Provincial Science and Technology,China。
文摘Ti185 alloy is widely used in key industrial fields such as aerospace due to its excellent mechanical properties.The traditional method of preparing Ti185 alloy will inevitably appear“βfleck”,resulting in the decrease of mechanical properties,and the high price of V element limits the wide application of Ti185.In this paper,a low-cost master alloy V-Fe powder is used,a dense block is prepared by spark plasma sintering(SPS)technology,and a high-performance Ti185 alloy is prepared by controlling the sintering parameters.XRD and SEM were used to investigate the phase and microstructure of the samples prepared under different parameters.The compressive strength and friction properties of the directly prepared samples were studied.The samples with a sintering temperature of 1350 ℃ and a holding time of 30 min exhibited the most excellent comprehensive performance,with the highest compressive strength and lowest friction coefficient of 1931.59 MPa and 0.47,respectively.
基金Project(92066205)supported by the National Natural Science Foundation of ChinaProject(2019-Z10)supported by the State Key Lab for Advanced Metals and Materials of ChinaProject(FRF-MP-20-52)supported by the Fundamental Research Funds for the Central Universities,China。
文摘The almost completely dense copper was prepared by ultrafine copper powder prepared with both methods of electrolysis and novel water-gas atomization through cold isostatic pressing(CIP)and sintering under atmospheric hydrogen.Fine copper powder possesses the higher sintering driving force,thereby promoting shrinkage and densification during the sintering process.The grain size of sintered samples by electrolytic copper powder is smaller than that prepared by the atomized copper powder,and the twin crystals are particularly prone to forming in the former sintered microstructure due to the raw powder with low oxygen content and high residual stress originating from the CIP process.The relative density of samples by electrolytic and atomized powder at 1000℃ sintering temperature achieves 99.3%and 97.4%,respectively,significantly higher than that of the powder metallurgy copper parts reported in the literature.Correspondingly,the ultimate tensile strength and yield strength of samples by both kinds of copper powder are approximately similar,while the elongation of the sintered sample by the electrolytic powder(60%)is apparently higher than the atomized powder(44%).The superior performance of samples fabricated by electrolytic powder is inferred from the full density and low oxygen level for there is no cuprous oxide in the grain boundaries.
文摘Similar friction welded joints of AA-7005 aluminum rods were fabricated using different combinations of process parameters such as friction pressure(1.0, 1.5 and 2.0 MPa) and friction time(10, 15 and 20 s). Interfacial microstructure and formation of intermetallic compounds at the joint interface were evaluated via scanning electron microscopy(SEM) equipped with energy dispersive spectrum(EDS), and optical microscopy(OM). Microstructural observations reveal the formation of intermetallic phases during the welding process which cannot be extruded from the interface. Theses phases influence the tensile strength of the resultant joints. From the tensile characteristics viewpoint, the greatest tensile strength value of 365 MPa is obtained at 1.5 MPa and 15 s. Finally, the role of microstructural features on tensile strength of resultant joints is discussed.
