ZnO is a highly significant II-VI semiconductor known for its excellent optoelectronic properties,making it widely applicable and promising for use in light-emitting devices,solar cells,lasers,and photodetectors.The m...ZnO is a highly significant II-VI semiconductor known for its excellent optoelectronic properties,making it widely applicable and promising for use in light-emitting devices,solar cells,lasers,and photodetectors.The methods for preparing ZnO are diverse,and among them,the hydrothermal method is favored for its simplicity,ease of operation,and low cost,making it an optimal choice for ZnO single-crystal growth.Most studies investigating the effects of different hydrothermal experimental parameters on the morphology and performance of ZnO nano-materials typically focus on only 2—3 variable parameters,with few examining the impact of all possible experimental parameter changes on ZnO nano-mate-rials.The principles of the hydrothermal method and its advantages in nano-material preparation were briefly introduced in this article.The detailed discussion on the influence of various experimental parameters on the preparation of ZnO nano-materials was provided,which including reaction materials,Zn^(2+)/OH^(-)ratio,reaction time and temperature,additives,experimental equipment,and annealing conditions.The review co-vers how different experimental parameters affect the morphology and performance of the materials,as well as how different rare earth doping elements influence the performance of ZnO nano-materials.It is hoped that this work will contribute to future research on the hydrothermal synthesis of nano-materials.展开更多
Buckypapers(BPs)consist of carbon nanotube(CNT)membranes with good mechanical,thermal and elec-trical properties.We report the modification of CNT buckypapers by the surface deposition of a thin layer of ti-tanium dio...Buckypapers(BPs)consist of carbon nanotube(CNT)membranes with good mechanical,thermal and elec-trical properties.We report the modification of CNT buckypapers by the surface deposition of a thin layer of ti-tanium dioxide and their subsequent photocatalytic use for the removal of three wastewater pollutants:diclofenac(DF),carbofuran(CB)and methylene blue(MB).The results show the following decreases(RE)in the initial concentrations of these pollutants,REDF=99.5%,REMB=96%and RECB=90%after 90 min of exposure to UV-Vis radiation using~0.6 mg of photocatalyst.Experiments also showed that the degradation rate of diclofenac(k=0.1028 min^(−1))is respectively 3.5 and 6 times faster than the values for CB(k=0.0298 min^(−1))and MB(k=0.0174 min^(−1)),probably due to the easier bond cleavage in DF.UV-Vis irradiated solutions of these pollutants were then analyzed by mass spectrometry to identify the species formed during photocatalysis and suggest possible degradation paths for MB,DF,and CB.Data showed that the degradation of DF involves the formation of a photocyclization product through loss of HCl molecule,clearly consuming less energy than that needed for the opening of the central aromatic ring in MB,or the loss of the N-methyl amide functional group for CB.展开更多
In recent years,chiral inorganic nanomaterials have become promising candidates for applications in sensing,catalysis,biomedicine,and photonics.Plasmonic nanomaterials with an intrinsic chiral structure exhibit intrig...In recent years,chiral inorganic nanomaterials have become promising candidates for applications in sensing,catalysis,biomedicine,and photonics.Plasmonic nanomaterials with an intrinsic chiral structure exhibit intriguing geometry‑dependent optical chirality,which benefits the combination of plasmonic characteristics with chirality.Recent advances in the biomolecule‑directed geometric control of intrinsically chiral plasmonic nanomaterials have further provided great opportunities for their widespread applications in many emerging technological areas.In this review,we present the recent progress in biosensing using chiral inorganic nanomaterials,with a particular focus on electrochemical and enzyme‑mimicking catalytic approaches.This paper commences with a review of the basic tenets underlying chiral nanocatalysts,incorporating the chiral ligand‑induced mechanism and the architectures of intrinsically chiral nanostructures.Additionally,it methodically expounds upon the applications of chiral nanocatalysts in the realms of electrochemical biosensing and enzyme‑mimicking catalytic biosensing respectively.Conclusively,it proffers a prospective view of the hurdles and prospects that accompany the deployment of chiral nanoprobes for nascent biosensing applications.By rational design of the chiral nanoprobes,it is envisioned that biosensing with increasing sensitivity and resolution toward the single‑molecule level can be achieved,which will substantially promote sensing applications in many emerging interdisciplinary areas.展开更多
A functional interlayer based on two-dimensional(2D)porous modified vermiculite nanosheets(PVS)was obtained by acid-etching vermiculite nanosheets.The as-obtained 2D porous nanosheets exhibited a high specific surface...A functional interlayer based on two-dimensional(2D)porous modified vermiculite nanosheets(PVS)was obtained by acid-etching vermiculite nanosheets.The as-obtained 2D porous nanosheets exhibited a high specific surface area of 427 m^(2)·g^(-1)and rich surface active sites,which help restrain polysulfides(LiPSs)through good physi-cal and chemical adsorption,while simultaneously accelerating the nucleation and dissolution kinetics of Li_(2)S,effec-tively suppressing the shuttle effect.The assembled lithium-sulfur batteries(LSBs)employing the PVS-based inter-layer delivered a high initial discharge capacity of 1386 mAh·g^(-1)at 0.1C(167.5 mAh·g^(-1)),long-term cycling stabil-ity,and good rate property.展开更多
The novel magnetic sepiolite/Fe_(3)O_(4)/zero-valent iron(nZVI)nanocomposite(nZVI@SepH-Mag)was prepared and used to achieve the removal of Cr(VI)in this work.The nZVI@SepH-Mag composites were characterized by XRD,FTIR...The novel magnetic sepiolite/Fe_(3)O_(4)/zero-valent iron(nZVI)nanocomposite(nZVI@SepH-Mag)was prepared and used to achieve the removal of Cr(VI)in this work.The nZVI@SepH-Mag composites were characterized by XRD,FTIR,BET,SEM and TEM.The characterization results indicated that the structure of the composite consisted of small nanoscale nZVI and magnetite(Mag)particles uniformly anchoring on the surface of acid-activated sepiolite(SepH).Batch experiments were used to analyze the effects of main factors on Cr(VI)removal.A 100%removal efficiency in 60 min and enhanced reaction ratio were reached by the composite comparing other existing materials.The kinetic of the adsorption and possible Cr(VI)removal mechanism of the hybrids were also evaluated and proposed.Based on the removal products identified by Raman,XRD and XPS,a reduction mechanism was proposed.The results indicated that the SepH and Mag can inhibit the agglomeration and enhance the dispersibility of nZVI,and Mag and nZVI displayed good synergetic effects.展开更多
Electrospinning technology has emerged as a promising method for fabricating flexible lithium-ion batter-ies(FLIBs)due to its ability to create materials with desir-able properties for energy storage applications.FLIB...Electrospinning technology has emerged as a promising method for fabricating flexible lithium-ion batter-ies(FLIBs)due to its ability to create materials with desir-able properties for energy storage applications.FLIBs,which are foldable and have high energy densities,are be-coming increasingly important as power sources for wear-able devices,flexible electronics,and mobile energy applica-tions.Carbon materials,especially carbon nanofibers,are pivotal in improving the performance of FLIBs by increas-ing electrical conductivity,chemical stability,and surface area,as well as reducing costs.These materials also play a significant role in establishing conducting networks and im-proving structural integrity,which are essential for extend-ing the cycle life and enhancing the safety of the batteries.This review considers the role of electrospinning in the fabrication of critical FLIB components,with a particular emphasis on the integration of carbon materials.It explores strategies to optimize FLIB performance by fine-tuning the electrospinning para-meters,such as electric field strength,spinning rate,solution concentration,and carbonization process.Precise control over fiber properties is crucial for enhancing battery reliability and stability during folding and bending.It also highlights the latest research findings in carbon-based electrode materials,high-performance electrolytes,and separator structures,discussing the practical challenges and opportunities these materials present.It underscores the significant impact of carbon materials on the evolution of FLIBs and their potential to shape future energy storage technologies.展开更多
The purpose of this study is to explore the adsorption performance of meso-2,3-dimercaptosuccinic acid(DMSA)modified Fe3O4@SiO2 magnetic nanocomposite(Fe3O4@SiO2@DMSA)for Pb2+ions removal from aqueous solutions.The ef...The purpose of this study is to explore the adsorption performance of meso-2,3-dimercaptosuccinic acid(DMSA)modified Fe3O4@SiO2 magnetic nanocomposite(Fe3O4@SiO2@DMSA)for Pb2+ions removal from aqueous solutions.The effects of solution pH,initial concentration of Pb2+ions,contact time,and temperature on the amount of Pb2+adsorbed were investigated.Adsorption isotherms,adsorption kinetics,and thermodynamic analysis were also studied.The results showed that the maximum adsorption capacity of the Fe3O4@SiO2@DMSA composite is 50.5 mg/g at 298 K,which is higher than that of Fe3O4 and Fe3O4@SiO2 magnetic nanoparticles.The adsorption process agreed well with Langmuir adsorption isotherm models and pseudo second-order kinetics.The thermodynamic analysis revealed that the adsorption was spontaneous,endothermic and energetically driven in nature.展开更多
Polyether ether ketone(PEEK)has good mechanical properties.However,its high viscosity when molten limits its use because it is hard to process.PEEK nanocomposites containing both carbon nanotubes(CNTs)and polyether im...Polyether ether ketone(PEEK)has good mechanical properties.However,its high viscosity when molten limits its use because it is hard to process.PEEK nanocomposites containing both carbon nanotubes(CNTs)and polyether imide(PEI)were pre-pared by a direct wet powder blending method using a vertical injection molding machine.The addition of an optimum amount of PEI lowered the viscosity of the molten PEEK by approximately 50%while producing an increase in the toughness of the nanocom-posites,whose strain to failure increased by 129%,and fracture energy increased by 97%.The uniformly dispersed CNT/PEI powder reduced the processing difficulty of PEEK nanocomposites without affecting the thermal resistance.This improvement of the strength and viscosity of PEEK facilitate its use in the preparation of thermoplastic composites.展开更多
Permanent ferrite magnet materials are extensively employed due to their exceptional magnetic properties and cost-effectiveness.The fast development in electromobile and household appliance industries contributes to a...Permanent ferrite magnet materials are extensively employed due to their exceptional magnetic properties and cost-effectiveness.The fast development in electromobile and household appliance industries contributes to a new progress in permanent ferrite materials.This paper reviews the deveolpement and progress of permanent ferrite magnet industry in recent years.The emergence of new raw material,the advancement of perparation methods and manufacturing techniques,and the potential applications of permanent ferrite materials are introduced and discussed.Specifically,nanocrystallization plays a crucial role in achieving high performance at a low cost and reducing reliance on rare earth resources,and therefore it could be a promising development trendency.展开更多
An active protection coating for pH-responsive was prepared.The hollow mesoporous silica microspheres(HMSNs)were loaded with 2-mercaptobenzothiazole(MBT),and then they were coated with chitosan(CS).The composite micro...An active protection coating for pH-responsive was prepared.The hollow mesoporous silica microspheres(HMSNs)were loaded with 2-mercaptobenzothiazole(MBT),and then they were coated with chitosan(CS).The composite microspheres were in the range of 650−750 nm in diameter.CS-HMSN-MBT coating had a faster repair rate under acidic conditions by synergistic effect between CS and MBT.The repair rate under alkaline conditions was slowed down.The active protection performance reached the strongest after 3 d immersion.The corrosion inhibitor release mechanism was optimized to extend the service life of the coating and to achieve long-term service of the copper substrate.展开更多
The chemical compound 3-(N-ethylamino)isobutyl)trimethoxysilane(EAMS)modified titanium dioxide(TiO_(2)),producing EAMS-TiO_(2),which was encased in graphitic carbon nitride(GCN)and integrated into epoxy resin(EP).The ...The chemical compound 3-(N-ethylamino)isobutyl)trimethoxysilane(EAMS)modified titanium dioxide(TiO_(2)),producing EAMS-TiO_(2),which was encased in graphitic carbon nitride(GCN)and integrated into epoxy resin(EP).The protective properties of mild steel coated with this nanocomposite in a marine environment were assessedusing electrochemical techniques.Thermogravimetric analysis(TGA)and Cone calorimetry tests demonstrated thatGCN/EAMS-TiO_(2)significantly enhanced the flame retardancy of the epoxy coating,reducing peak heat release rate(PHRR)and total heat release(THR)values by 88%and 70%,respectively,compared to pure EP.Salt spray testsindicated reduced water absorption and improved corrosion resistance.The optimal concentration of 0.6 wt%GCNEAMS/TiO_(2)yielded the highest resistance,with the nanocomposite achieving a coating resistance of 7.50×10^(10)Ω·cm^(2)after 28 d in seawater.The surface resistance of EP-GCN/EAMS-TiO_(2)was over 99.9 times higher than pure EP after onehour in seawater.SECM analysis showed the lowest ferrous ion dissipation(1.0 nA)for EP-GCN/EAMS-TiO_(2)coatedsteel.FE-SEM and EDX analyses revealed improved breakdown products and a durable inert nanolayered covering.Thenanocomposite exhibited excellent water resistance(water contact angle of 167°)and strong mechanical properties,withadhesive strength increasing to 18.3 MPa after 28 d in seawater.EP-GCN/EAMS-TiO_(2)shows potential as a coatingmaterial for the shipping industry.展开更多
A 3D nitrogen⁃doped graphene/multi⁃walled carbon nanotube(CS⁃GO⁃NCNT)crosslinked network mate⁃rial was successfully synthesized utilizing chitosan and melamine as carbon and nitrogen sources,concomitant with the incor...A 3D nitrogen⁃doped graphene/multi⁃walled carbon nanotube(CS⁃GO⁃NCNT)crosslinked network mate⁃rial was successfully synthesized utilizing chitosan and melamine as carbon and nitrogen sources,concomitant with the incorporation of multi⁃wall carbon nanotubes and employing freeze drying technology.The material amalgamates the merits of 1D/2D hybrid carbon materials,wherein 1D carbon nanotubes confer robustness and expedited elec⁃tron transport pathways,while 2D graphene sheets facilitate rapid ion migration.Furthermore,the introduction of nitrogen heteroatoms serves to furnish additional active sites for lithium storage.When served as an anode material for lithium⁃ion batteries,the CS⁃GO⁃NCNT electrode delivered a reversible capacity surpassing 500 mAh·g^(-1),mark⁃edly outperforming commercial graphite anodes.Even after 300 cycles at a high current density of 1 A·g^(-1),it remained a reversible capacity of up to 268 mAh·g^(-1).展开更多
The intensifying global energy crisis,coupled with environmental degradation from fossil fuels,highlights that photocatalytic hydrogen evolution technology offers a promising solution due to its efficiency and sustain...The intensifying global energy crisis,coupled with environmental degradation from fossil fuels,highlights that photocatalytic hydrogen evolution technology offers a promising solution due to its efficiency and sustainability.In this study,we synthesized CeO_(2)/Cd_(7.23)Zn_(2.77)S_(10)-DETA(diethylenetriamine is abbreviated as DETA,and subsequently CeO_(2)is referred to as EO,Cd_(7.23)Zn_(2.77)S_(10)-DETA is abbreviated as ZCS,and the composite with EO comprising 30%is abbreviated as EO/ZCS)nanocomposites with S-scheme heterojunctions.Under conditions without external co-catalysts and utilizing only visible light as the excitation source,EO/ZCS nanocomposites exhibited outstanding photocatalytic hydrogen evolution activity and remarkable stability,presenting significant advantages over conventional methods that rely on co-catalysts and ultraviolet light.The photocatalytic hydrogen evolution rate of EO/ZCS nanocomposites reached 4.11 mmol/(g·h),significantly surpassing that of EO(trace)and ZCS(2.78 mmol/(g·h)).This substantial enhancement is attributed to the S-scheme charge transfer mechanism at the heterojunctions in EO/ZCS nanocomposites,which effectively facilitates the efficient separation and transfer of photogenerated electron-hole pairs,thereby substantially enhancing photocatalytic hydrogen evolution activity.Through techniques such as X-ray photoelectron spectroscopy(XPS)and theoretical calculations,we confirmed the formation of S-scheme heterojunctions and elucidated their photocatalytic hydrogen evolution mechanism.The results underscore the potential of EO/ZCS nanocomposites as highly efficient and stable photocatalysts for hydrogen production under environmentally benign conditions.展开更多
A novel molecularly imprinted polymer (MIP) based on upconversion nanoparticles (UCNPs) was successfully synthesized for determination of Ochratoxin A (OTA). The MIP was developed on the silica-coated UCNPs using N-(1...A novel molecularly imprinted polymer (MIP) based on upconversion nanoparticles (UCNPs) was successfully synthesized for determination of Ochratoxin A (OTA). The MIP was developed on the silica-coated UCNPs using N-(1-hydroxy-2-naphthoyl amido)-(L)-phenylalanine (HNA-Phe) as the alternative template. The final composite combined the advantages of the high selectivity of MIP with the high fluorescence intensity of UCNPs which was selective and sensitive to OTA. Under the optimal condition, the fluorescence intensity of UCNPs@SiO2@MIP decreases linearly when the concentration of OTA increases from 0.05 to 1.0 mg/L. The detection limit of OTA with the method was 0.031 mg/L. At three spiked concentration levels (50, 100 and 200 μg/kg), the recovery ranges of OTA in corn, rice and feed are 88.0%–91.6%, 80.2%–91.6% and 89.2%–90.4%, respectively.展开更多
TiC nanoparticles reinforced 2219 aluminum matrix composites were successfully prepared by ultrasonic casting, followed by forging and T6 heat treatment. The friction and wear properties of the disc-to-column were stu...TiC nanoparticles reinforced 2219 aluminum matrix composites were successfully prepared by ultrasonic casting, followed by forging and T6 heat treatment. The friction and wear properties of the disc-to-column were studied under four separate normal values of 5, 10, 20 and 30 N. The increasing hardness value of the nanocomposite may be attributed to the large amount of TiC(i.e., 1.3 wt.% and 1.7 wt.%) introduced to the composites. The friction coefficient of the nanocomposite decreased with the increase of TiC nanoparticles(0-1.7 wt.%) under the same load. But the wear resistance of the TiC/AA2219 nanocomposite increased by 30%-90% as compared to the 2219 matrix alloy. And it decreased with the increasing load. The composite with 0.9 wt.% TiC produced the best results in terms of friction and wear because of its relatively higher hardness and perfect ability to retain a transfer layer of a comparatively larger thickness. On the wear surface, some Al2O3particles were found which aided in the development of protective shear regions and improved the wear resistance. The wear mechanism for the TiC/AA2219 nanocomposite was a combination of adhesive and oxidative wear, with the composites containing hard TiC nanoparticles being mainly abrasive.展开更多
Magnetic nanoparticles （Fe304） were prepared by chemical precipitation method using Fe^2＋ and Fe^3＋ salts with sodium hydroxide in the nitrogen atmosphere. Fe3O4 nanoparticles were coated with human serum albumin...Magnetic nanoparticles （Fe304） were prepared by chemical precipitation method using Fe^2＋ and Fe^3＋ salts with sodium hydroxide in the nitrogen atmosphere. Fe3O4 nanoparticles were coated with human serum albumin（HSA） for magnetic resonance imaging as contrast agent. Characteristics of magnetic particles coated or uncoated were carried out using scanning electron microscopy and X-ray diffraction. Zeta potentials, package effects and distributions of colloid particles were measured to confirm the attachment of HSA on magnetic particles. Effects of Fe3O4 nanoparticles coated with HSA on magnetic resonance imaging were investigated with rats. The experimental results show that the adsorption of HSA on magnetic particles is very favorable to dispersing of magnetic Fe3O4 particles, while the sizes of Fe3O4 particles coated are related to the molar ratio of Fe3O4 to HSA. The diameters of the majority of particles coated are less than 100 nm. Fe3O4 nanoparticle coated with HSA has a good biocompatibility and low toxicity. This new contrast agent has some effects on the nuclear magnetic resonance imaging of liver and the lowest dosage is 20μmol/kg for the demands of diagnosis.展开更多
Present work reports chemically reacting Darcy-Forchheimer flow of nanotubes.Water is utilized as base liquid while carbon nanotubes are considered nanomaterial.An exponential stretchable curved surface flow is origin...Present work reports chemically reacting Darcy-Forchheimer flow of nanotubes.Water is utilized as base liquid while carbon nanotubes are considered nanomaterial.An exponential stretchable curved surface flow is originated.Heat source is present.Xue relation of nanoliquid is employed to explore the feature of CNTs (single and multi-wall).Transformation technique is adopted in order to achieve non-linear ordinary differential systems.The governing systems are solved numerically.Effects of involved parameters on flow,temperature,concentration,heat transfer rate (Nusselt number) with addition of skin friction coefficient are illustrated graphically.Decay in velocity is noted with an increment in Forchheimer number and porosity parameter while opposite impact is seen for temperature.Moreover,role of MWCNTs is prominent when compared with SWCNTs.展开更多
A hydroxyl-functionalized magnetic fungus nanocomposite(MFH@GO)was prepared by a simple one-pot method for the removal of Cr(VI)from wastewater.The adsorption behavior of MFH@GO to Cr(VI)in wastewater was discussed in...A hydroxyl-functionalized magnetic fungus nanocomposite(MFH@GO)was prepared by a simple one-pot method for the removal of Cr(VI)from wastewater.The adsorption behavior of MFH@GO to Cr(VI)in wastewater was discussed in detail.At pH of 5.0 and temperature of 323.15 K,MFH@GO had higher adsorption capacity to Cr(VI)(58.4 mg/g)than the unmodified fungus and GO.Fourier transform infrared spectroscopy(FTIR),X-ray diffraction(XRD),thermogravimetry and differential thermal analysis(TG-DTA),scanning electron microscopy and energy dispersive X-Ray spectroscopy(SEM-EDX)were employed to determine the characteristics of MFH@GO.Results showed that magnetic graphene oxide nanoparticles significantly enhanced the physiochemical properties of the fungi.In addition,the adsorption mechanisms analyses show that Cr(VI)could be reduced and mineralized into ferric chromate in residues.These results suggested that MFH@GO could be used as an promising and alternative biosorbent for removal of Cr(VI)from industrial wastewater.展开更多
文摘ZnO is a highly significant II-VI semiconductor known for its excellent optoelectronic properties,making it widely applicable and promising for use in light-emitting devices,solar cells,lasers,and photodetectors.The methods for preparing ZnO are diverse,and among them,the hydrothermal method is favored for its simplicity,ease of operation,and low cost,making it an optimal choice for ZnO single-crystal growth.Most studies investigating the effects of different hydrothermal experimental parameters on the morphology and performance of ZnO nano-materials typically focus on only 2—3 variable parameters,with few examining the impact of all possible experimental parameter changes on ZnO nano-mate-rials.The principles of the hydrothermal method and its advantages in nano-material preparation were briefly introduced in this article.The detailed discussion on the influence of various experimental parameters on the preparation of ZnO nano-materials was provided,which including reaction materials,Zn^(2+)/OH^(-)ratio,reaction time and temperature,additives,experimental equipment,and annealing conditions.The review co-vers how different experimental parameters affect the morphology and performance of the materials,as well as how different rare earth doping elements influence the performance of ZnO nano-materials.It is hoped that this work will contribute to future research on the hydrothermal synthesis of nano-materials.
基金MIUR,Italian Ministry for University and Research(EX-60%/2024)。
文摘Buckypapers(BPs)consist of carbon nanotube(CNT)membranes with good mechanical,thermal and elec-trical properties.We report the modification of CNT buckypapers by the surface deposition of a thin layer of ti-tanium dioxide and their subsequent photocatalytic use for the removal of three wastewater pollutants:diclofenac(DF),carbofuran(CB)and methylene blue(MB).The results show the following decreases(RE)in the initial concentrations of these pollutants,REDF=99.5%,REMB=96%and RECB=90%after 90 min of exposure to UV-Vis radiation using~0.6 mg of photocatalyst.Experiments also showed that the degradation rate of diclofenac(k=0.1028 min^(−1))is respectively 3.5 and 6 times faster than the values for CB(k=0.0298 min^(−1))and MB(k=0.0174 min^(−1)),probably due to the easier bond cleavage in DF.UV-Vis irradiated solutions of these pollutants were then analyzed by mass spectrometry to identify the species formed during photocatalysis and suggest possible degradation paths for MB,DF,and CB.Data showed that the degradation of DF involves the formation of a photocyclization product through loss of HCl molecule,clearly consuming less energy than that needed for the opening of the central aromatic ring in MB,or the loss of the N-methyl amide functional group for CB.
文摘In recent years,chiral inorganic nanomaterials have become promising candidates for applications in sensing,catalysis,biomedicine,and photonics.Plasmonic nanomaterials with an intrinsic chiral structure exhibit intriguing geometry‑dependent optical chirality,which benefits the combination of plasmonic characteristics with chirality.Recent advances in the biomolecule‑directed geometric control of intrinsically chiral plasmonic nanomaterials have further provided great opportunities for their widespread applications in many emerging technological areas.In this review,we present the recent progress in biosensing using chiral inorganic nanomaterials,with a particular focus on electrochemical and enzyme‑mimicking catalytic approaches.This paper commences with a review of the basic tenets underlying chiral nanocatalysts,incorporating the chiral ligand‑induced mechanism and the architectures of intrinsically chiral nanostructures.Additionally,it methodically expounds upon the applications of chiral nanocatalysts in the realms of electrochemical biosensing and enzyme‑mimicking catalytic biosensing respectively.Conclusively,it proffers a prospective view of the hurdles and prospects that accompany the deployment of chiral nanoprobes for nascent biosensing applications.By rational design of the chiral nanoprobes,it is envisioned that biosensing with increasing sensitivity and resolution toward the single‑molecule level can be achieved,which will substantially promote sensing applications in many emerging interdisciplinary areas.
文摘A functional interlayer based on two-dimensional(2D)porous modified vermiculite nanosheets(PVS)was obtained by acid-etching vermiculite nanosheets.The as-obtained 2D porous nanosheets exhibited a high specific surface area of 427 m^(2)·g^(-1)and rich surface active sites,which help restrain polysulfides(LiPSs)through good physi-cal and chemical adsorption,while simultaneously accelerating the nucleation and dissolution kinetics of Li_(2)S,effec-tively suppressing the shuttle effect.The assembled lithium-sulfur batteries(LSBs)employing the PVS-based inter-layer delivered a high initial discharge capacity of 1386 mAh·g^(-1)at 0.1C(167.5 mAh·g^(-1)),long-term cycling stabil-ity,and good rate property.
基金Projects(52474138,52104261,52525401)supported by the National Natural Science Foundation of ChinaProject supported by the New Cornerstone Science Foundation through the XPLORER PRIZE,ChinaProject supported by the Shanxi Key Laboratory Funds of Mine Rock Strata Control and Disaster Prevention,China。
文摘The novel magnetic sepiolite/Fe_(3)O_(4)/zero-valent iron(nZVI)nanocomposite(nZVI@SepH-Mag)was prepared and used to achieve the removal of Cr(VI)in this work.The nZVI@SepH-Mag composites were characterized by XRD,FTIR,BET,SEM and TEM.The characterization results indicated that the structure of the composite consisted of small nanoscale nZVI and magnetite(Mag)particles uniformly anchoring on the surface of acid-activated sepiolite(SepH).Batch experiments were used to analyze the effects of main factors on Cr(VI)removal.A 100%removal efficiency in 60 min and enhanced reaction ratio were reached by the composite comparing other existing materials.The kinetic of the adsorption and possible Cr(VI)removal mechanism of the hybrids were also evaluated and proposed.Based on the removal products identified by Raman,XRD and XPS,a reduction mechanism was proposed.The results indicated that the SepH and Mag can inhibit the agglomeration and enhance the dispersibility of nZVI,and Mag and nZVI displayed good synergetic effects.
文摘Electrospinning technology has emerged as a promising method for fabricating flexible lithium-ion batter-ies(FLIBs)due to its ability to create materials with desir-able properties for energy storage applications.FLIBs,which are foldable and have high energy densities,are be-coming increasingly important as power sources for wear-able devices,flexible electronics,and mobile energy applica-tions.Carbon materials,especially carbon nanofibers,are pivotal in improving the performance of FLIBs by increas-ing electrical conductivity,chemical stability,and surface area,as well as reducing costs.These materials also play a significant role in establishing conducting networks and im-proving structural integrity,which are essential for extend-ing the cycle life and enhancing the safety of the batteries.This review considers the role of electrospinning in the fabrication of critical FLIB components,with a particular emphasis on the integration of carbon materials.It explores strategies to optimize FLIB performance by fine-tuning the electrospinning para-meters,such as electric field strength,spinning rate,solution concentration,and carbonization process.Precise control over fiber properties is crucial for enhancing battery reliability and stability during folding and bending.It also highlights the latest research findings in carbon-based electrode materials,high-performance electrolytes,and separator structures,discussing the practical challenges and opportunities these materials present.It underscores the significant impact of carbon materials on the evolution of FLIBs and their potential to shape future energy storage technologies.
基金Project(2013DFA51290)supported by International S&T Cooperation Program of China
文摘The purpose of this study is to explore the adsorption performance of meso-2,3-dimercaptosuccinic acid(DMSA)modified Fe3O4@SiO2 magnetic nanocomposite(Fe3O4@SiO2@DMSA)for Pb2+ions removal from aqueous solutions.The effects of solution pH,initial concentration of Pb2+ions,contact time,and temperature on the amount of Pb2+adsorbed were investigated.Adsorption isotherms,adsorption kinetics,and thermodynamic analysis were also studied.The results showed that the maximum adsorption capacity of the Fe3O4@SiO2@DMSA composite is 50.5 mg/g at 298 K,which is higher than that of Fe3O4 and Fe3O4@SiO2 magnetic nanoparticles.The adsorption process agreed well with Langmuir adsorption isotherm models and pseudo second-order kinetics.The thermodynamic analysis revealed that the adsorption was spontaneous,endothermic and energetically driven in nature.
文摘Polyether ether ketone(PEEK)has good mechanical properties.However,its high viscosity when molten limits its use because it is hard to process.PEEK nanocomposites containing both carbon nanotubes(CNTs)and polyether imide(PEI)were pre-pared by a direct wet powder blending method using a vertical injection molding machine.The addition of an optimum amount of PEI lowered the viscosity of the molten PEEK by approximately 50%while producing an increase in the toughness of the nanocom-posites,whose strain to failure increased by 129%,and fracture energy increased by 97%.The uniformly dispersed CNT/PEI powder reduced the processing difficulty of PEEK nanocomposites without affecting the thermal resistance.This improvement of the strength and viscosity of PEEK facilitate its use in the preparation of thermoplastic composites.
基金Project(1053320222852)supported by the Graduate Student Innovation Program of Central South University,China。
文摘Permanent ferrite magnet materials are extensively employed due to their exceptional magnetic properties and cost-effectiveness.The fast development in electromobile and household appliance industries contributes to a new progress in permanent ferrite materials.This paper reviews the deveolpement and progress of permanent ferrite magnet industry in recent years.The emergence of new raw material,the advancement of perparation methods and manufacturing techniques,and the potential applications of permanent ferrite materials are introduced and discussed.Specifically,nanocrystallization plays a crucial role in achieving high performance at a low cost and reducing reliance on rare earth resources,and therefore it could be a promising development trendency.
基金Project(2023YFC2907304)supported by the National Key R&D Program Projects,ChinaProject(ZR2021ME087)supported by the Natural Science Foundation of Shandong Province,China+1 种基金Project(2022KLMM305)supported by the Shandong Provincial Key Laboratory of Mining Machinery Engineering School Enterprise Joint Fund,ChinaProject(2023CXPT062)supported by the Shandong Key Research and Development Program(Competitive Innovation Platform),China。
文摘An active protection coating for pH-responsive was prepared.The hollow mesoporous silica microspheres(HMSNs)were loaded with 2-mercaptobenzothiazole(MBT),and then they were coated with chitosan(CS).The composite microspheres were in the range of 650−750 nm in diameter.CS-HMSN-MBT coating had a faster repair rate under acidic conditions by synergistic effect between CS and MBT.The repair rate under alkaline conditions was slowed down.The active protection performance reached the strongest after 3 d immersion.The corrosion inhibitor release mechanism was optimized to extend the service life of the coating and to achieve long-term service of the copper substrate.
文摘The chemical compound 3-(N-ethylamino)isobutyl)trimethoxysilane(EAMS)modified titanium dioxide(TiO_(2)),producing EAMS-TiO_(2),which was encased in graphitic carbon nitride(GCN)and integrated into epoxy resin(EP).The protective properties of mild steel coated with this nanocomposite in a marine environment were assessedusing electrochemical techniques.Thermogravimetric analysis(TGA)and Cone calorimetry tests demonstrated thatGCN/EAMS-TiO_(2)significantly enhanced the flame retardancy of the epoxy coating,reducing peak heat release rate(PHRR)and total heat release(THR)values by 88%and 70%,respectively,compared to pure EP.Salt spray testsindicated reduced water absorption and improved corrosion resistance.The optimal concentration of 0.6 wt%GCNEAMS/TiO_(2)yielded the highest resistance,with the nanocomposite achieving a coating resistance of 7.50×10^(10)Ω·cm^(2)after 28 d in seawater.The surface resistance of EP-GCN/EAMS-TiO_(2)was over 99.9 times higher than pure EP after onehour in seawater.SECM analysis showed the lowest ferrous ion dissipation(1.0 nA)for EP-GCN/EAMS-TiO_(2)coatedsteel.FE-SEM and EDX analyses revealed improved breakdown products and a durable inert nanolayered covering.Thenanocomposite exhibited excellent water resistance(water contact angle of 167°)and strong mechanical properties,withadhesive strength increasing to 18.3 MPa after 28 d in seawater.EP-GCN/EAMS-TiO_(2)shows potential as a coatingmaterial for the shipping industry.
文摘A 3D nitrogen⁃doped graphene/multi⁃walled carbon nanotube(CS⁃GO⁃NCNT)crosslinked network mate⁃rial was successfully synthesized utilizing chitosan and melamine as carbon and nitrogen sources,concomitant with the incorporation of multi⁃wall carbon nanotubes and employing freeze drying technology.The material amalgamates the merits of 1D/2D hybrid carbon materials,wherein 1D carbon nanotubes confer robustness and expedited elec⁃tron transport pathways,while 2D graphene sheets facilitate rapid ion migration.Furthermore,the introduction of nitrogen heteroatoms serves to furnish additional active sites for lithium storage.When served as an anode material for lithium⁃ion batteries,the CS⁃GO⁃NCNT electrode delivered a reversible capacity surpassing 500 mAh·g^(-1),mark⁃edly outperforming commercial graphite anodes.Even after 300 cycles at a high current density of 1 A·g^(-1),it remained a reversible capacity of up to 268 mAh·g^(-1).
基金Project(42407636)supported by the National Natural Science Foundation of ChinaProject(2022AH040068)supported by the Major Foundation of the Educational Commission of Anhui Province,China+2 种基金Project(2023AH051861)supported by the Natural Science Research Project for Colleges and Universities in Anhui Province,ChinaProject(SPYJ202201)supported by the Talent Introduction Foundation of Anhui Science and Technology University,ChinaProject(202310879096)supported by the Innovation and Entrepreneurship Training Program for College Students,China。
文摘The intensifying global energy crisis,coupled with environmental degradation from fossil fuels,highlights that photocatalytic hydrogen evolution technology offers a promising solution due to its efficiency and sustainability.In this study,we synthesized CeO_(2)/Cd_(7.23)Zn_(2.77)S_(10)-DETA(diethylenetriamine is abbreviated as DETA,and subsequently CeO_(2)is referred to as EO,Cd_(7.23)Zn_(2.77)S_(10)-DETA is abbreviated as ZCS,and the composite with EO comprising 30%is abbreviated as EO/ZCS)nanocomposites with S-scheme heterojunctions.Under conditions without external co-catalysts and utilizing only visible light as the excitation source,EO/ZCS nanocomposites exhibited outstanding photocatalytic hydrogen evolution activity and remarkable stability,presenting significant advantages over conventional methods that rely on co-catalysts and ultraviolet light.The photocatalytic hydrogen evolution rate of EO/ZCS nanocomposites reached 4.11 mmol/(g·h),significantly surpassing that of EO(trace)and ZCS(2.78 mmol/(g·h)).This substantial enhancement is attributed to the S-scheme charge transfer mechanism at the heterojunctions in EO/ZCS nanocomposites,which effectively facilitates the efficient separation and transfer of photogenerated electron-hole pairs,thereby substantially enhancing photocatalytic hydrogen evolution activity.Through techniques such as X-ray photoelectron spectroscopy(XPS)and theoretical calculations,we confirmed the formation of S-scheme heterojunctions and elucidated their photocatalytic hydrogen evolution mechanism.The results underscore the potential of EO/ZCS nanocomposites as highly efficient and stable photocatalysts for hydrogen production under environmentally benign conditions.
基金Project(17ZYPTJC00050)supported by Science and Technology Committee of Tianjin,ChinaProject(2017YFC1600803)supported by the Ministry of Science and Technology of China
文摘A novel molecularly imprinted polymer (MIP) based on upconversion nanoparticles (UCNPs) was successfully synthesized for determination of Ochratoxin A (OTA). The MIP was developed on the silica-coated UCNPs using N-(1-hydroxy-2-naphthoyl amido)-(L)-phenylalanine (HNA-Phe) as the alternative template. The final composite combined the advantages of the high selectivity of MIP with the high fluorescence intensity of UCNPs which was selective and sensitive to OTA. Under the optimal condition, the fluorescence intensity of UCNPs@SiO2@MIP decreases linearly when the concentration of OTA increases from 0.05 to 1.0 mg/L. The detection limit of OTA with the method was 0.031 mg/L. At three spiked concentration levels (50, 100 and 200 μg/kg), the recovery ranges of OTA in corn, rice and feed are 88.0%–91.6%, 80.2%–91.6% and 89.2%–90.4%, respectively.
基金Project(2020RC2002) supported by Science and Technology Innovation Program of Hunan Province,ChinaProject(2021JJ40774) supported by Natural Science Foundation of Hunan Province,China+2 种基金Project(20A430007) supported by Key Scientific Research Projects of Colleges and Universities in Henan Province,ChinaProject(212102210032)supported by the Key Scientific and Technological Projects in Henan Province,ChinaProject(HEU10202117)supported by the Key Laboratory of Superlight Materials Surface Technology,Ministry of Education,China。
文摘TiC nanoparticles reinforced 2219 aluminum matrix composites were successfully prepared by ultrasonic casting, followed by forging and T6 heat treatment. The friction and wear properties of the disc-to-column were studied under four separate normal values of 5, 10, 20 and 30 N. The increasing hardness value of the nanocomposite may be attributed to the large amount of TiC(i.e., 1.3 wt.% and 1.7 wt.%) introduced to the composites. The friction coefficient of the nanocomposite decreased with the increase of TiC nanoparticles(0-1.7 wt.%) under the same load. But the wear resistance of the TiC/AA2219 nanocomposite increased by 30%-90% as compared to the 2219 matrix alloy. And it decreased with the increasing load. The composite with 0.9 wt.% TiC produced the best results in terms of friction and wear because of its relatively higher hardness and perfect ability to retain a transfer layer of a comparatively larger thickness. On the wear surface, some Al2O3particles were found which aided in the development of protective shear regions and improved the wear resistance. The wear mechanism for the TiC/AA2219 nanocomposite was a combination of adhesive and oxidative wear, with the composites containing hard TiC nanoparticles being mainly abrasive.
文摘Magnetic nanoparticles （Fe304） were prepared by chemical precipitation method using Fe^2＋ and Fe^3＋ salts with sodium hydroxide in the nitrogen atmosphere. Fe3O4 nanoparticles were coated with human serum albumin（HSA） for magnetic resonance imaging as contrast agent. Characteristics of magnetic particles coated or uncoated were carried out using scanning electron microscopy and X-ray diffraction. Zeta potentials, package effects and distributions of colloid particles were measured to confirm the attachment of HSA on magnetic particles. Effects of Fe3O4 nanoparticles coated with HSA on magnetic resonance imaging were investigated with rats. The experimental results show that the adsorption of HSA on magnetic particles is very favorable to dispersing of magnetic Fe3O4 particles, while the sizes of Fe3O4 particles coated are related to the molar ratio of Fe3O4 to HSA. The diameters of the majority of particles coated are less than 100 nm. Fe3O4 nanoparticle coated with HSA has a good biocompatibility and low toxicity. This new contrast agent has some effects on the nuclear magnetic resonance imaging of liver and the lowest dosage is 20μmol/kg for the demands of diagnosis.
文摘Present work reports chemically reacting Darcy-Forchheimer flow of nanotubes.Water is utilized as base liquid while carbon nanotubes are considered nanomaterial.An exponential stretchable curved surface flow is originated.Heat source is present.Xue relation of nanoliquid is employed to explore the feature of CNTs (single and multi-wall).Transformation technique is adopted in order to achieve non-linear ordinary differential systems.The governing systems are solved numerically.Effects of involved parameters on flow,temperature,concentration,heat transfer rate (Nusselt number) with addition of skin friction coefficient are illustrated graphically.Decay in velocity is noted with an increment in Forchheimer number and porosity parameter while opposite impact is seen for temperature.Moreover,role of MWCNTs is prominent when compared with SWCNTs.
基金Project(18B195)supported by Excellent Youth Project of Hunan Education Department,ChinaProjects(51804353,51704093)supported by the National Natural Science Foundation of China+2 种基金Project(kq1801074)supported by Key Projects of Changsha Science and Technology Plan,ChinaProject(2018JJ4010)supported by Hunan Provincial Natural Science Foundation of China(Joint Funds of Provincial and Zhuzhou Municipal)Project(2018JJ3885)supported by Natural Science Foundation of Hunan Province of China(Science Foundation for Youths)。
文摘A hydroxyl-functionalized magnetic fungus nanocomposite(MFH@GO)was prepared by a simple one-pot method for the removal of Cr(VI)from wastewater.The adsorption behavior of MFH@GO to Cr(VI)in wastewater was discussed in detail.At pH of 5.0 and temperature of 323.15 K,MFH@GO had higher adsorption capacity to Cr(VI)(58.4 mg/g)than the unmodified fungus and GO.Fourier transform infrared spectroscopy(FTIR),X-ray diffraction(XRD),thermogravimetry and differential thermal analysis(TG-DTA),scanning electron microscopy and energy dispersive X-Ray spectroscopy(SEM-EDX)were employed to determine the characteristics of MFH@GO.Results showed that magnetic graphene oxide nanoparticles significantly enhanced the physiochemical properties of the fungi.In addition,the adsorption mechanisms analyses show that Cr(VI)could be reduced and mineralized into ferric chromate in residues.These results suggested that MFH@GO could be used as an promising and alternative biosorbent for removal of Cr(VI)from industrial wastewater.
