期刊文献+
共找到11篇文章
< 1 >
每页显示 20 50 100
基于遗传算法的一类不确定性扰动下的系统参数估计 被引量:4
1
作者 李世玲 张富堂 李治 《系统仿真学报》 CAS CSCD 2002年第5期566-568,572,共4页
对于线性系统,本文针对其系统矩阵A存在一类不确定性扰动的情况,提出了一种基于遗传算法(GA)的新的参数估计方法。同基于线性矩阵不等式(LMI)的参数估计方法相比,这种方法求解速度快,更适合于高维系统参数估计,为改进仪表测量误差对高... 对于线性系统,本文针对其系统矩阵A存在一类不确定性扰动的情况,提出了一种基于遗传算法(GA)的新的参数估计方法。同基于线性矩阵不等式(LMI)的参数估计方法相比,这种方法求解速度快,更适合于高维系统参数估计,为改进仪表测量误差对高维系统建模精度带来的影响提供了一条可行的途径。仿真实验表明,本文提出的方法具有高度鲁棒性和很好的精度,能有效地消除不确定性扰动对系统精度的影响。 展开更多
关键词 遗传算法 不确定性扰动 系统参数估计 遗传算法 鲁棒性
在线阅读 下载PDF
机载三基线干涉合成孔径雷达的系统参数估计
2
作者 马萌 李道京 +1 位作者 潘舟浩 杜剑波 《中国科学院大学学报(中英文)》 CAS CSCD 北大核心 2015年第6期783-789,共7页
针对机载刚性三基线干涉合成孔径雷达的应用需求,在存在干涉相位噪声的情况下,研究基于2个地面控制点估计系统基线倾角和干涉相位偏差的问题,分析干涉相位噪声对参数估计精度的影响,提出一种三基线联合参数估计方法.使用牛顿法求解系统... 针对机载刚性三基线干涉合成孔径雷达的应用需求,在存在干涉相位噪声的情况下,研究基于2个地面控制点估计系统基线倾角和干涉相位偏差的问题,分析干涉相位噪声对参数估计精度的影响,提出一种三基线联合参数估计方法.使用牛顿法求解系统参数估计方程,根据不同基线的高程测量精度,对目标函数进行加权处理,并使用不同基线得到的高程差来评价参数估计效果.仿真结果表明,相比于传统的单基线参数估计方法,该方法具有较高的参数估计精度. 展开更多
关键词 干涉合成孔径雷达 系统参数估计 机载三基线
在线阅读 下载PDF
基于系统参数估计的重型汽车燃油经济性分析 被引量:4
3
作者 谭秀卿 卜绍先 《汽车工程》 EI CSCD 北大核心 2007年第12期1083-1085,共3页
在传统汽车动力性模型基础上,采用系统参数辨识技术,利用汽车道路滑行和加速试验得到的相关数据,识别出动力性模型中的主要参数:空气阻力系数、滚动阻力系数和传动系机械效率,有效解决了在缺少有关参数时对汽车燃油经济性的分析问题,并... 在传统汽车动力性模型基础上,采用系统参数辨识技术,利用汽车道路滑行和加速试验得到的相关数据,识别出动力性模型中的主要参数:空气阻力系数、滚动阻力系数和传动系机械效率,有效解决了在缺少有关参数时对汽车燃油经济性的分析问题,并取得满意的结果。 展开更多
关键词 汽车动力性模型 燃油经济性 系统参数估计
在线阅读 下载PDF
振动系统结构参数估计的Taylor变换法 被引量:3
4
作者 苏志霄 刘宏昭 +1 位作者 李鹏飞 曹惟庆 《应用力学学报》 EI CAS CSCD 北大核心 2000年第1期47-53,共7页
引入了求解非线性微分方程的 Taylor变换法 ,将振动系统原分析模型变换为离散域内的代数方程组 ,建立了估计系统质量、阻尼和刚度矩阵的方程。该方法可以利用任意外载激励下的瞬态响应估计系统的结构参数 ,而不需要进行系统的模态试验 ... 引入了求解非线性微分方程的 Taylor变换法 ,将振动系统原分析模型变换为离散域内的代数方程组 ,建立了估计系统质量、阻尼和刚度矩阵的方程。该方法可以利用任意外载激励下的瞬态响应估计系统的结构参数 ,而不需要进行系统的模态试验 ,具有一定的工程应用价值。文中还研究了测试信号受噪声干扰时的参数估计方法 ,最后给出了 30 0 T转炉倾动机构的参数估计实例。 展开更多
关键词 Taylor变换法 系统结构参数估计 振动系统
在线阅读 下载PDF
林分直径分布的Weibull参数估计系统研制 被引量:3
5
作者 谢鹏芳 谢敏 +3 位作者 裴志涛 黄旭光 黄家荣 周俊朝 《河南农业大学学报》 CAS CSCD 北大核心 2016年第1期45-49,共5页
基于Weibull分布3参数的人工神经网络估计模型,用MATLAB的GUI界面编制了Weibull参数估计系统(WPES)。以3个年龄段(14、22和30 a)的贵州马尾松人工林直径分布数据为验证材料,用最大似然估计(MLE)为对照,对WPES的准确性和适应性进... 基于Weibull分布3参数的人工神经网络估计模型,用MATLAB的GUI界面编制了Weibull参数估计系统(WPES)。以3个年龄段(14、22和30 a)的贵州马尾松人工林直径分布数据为验证材料,用最大似然估计(MLE)为对照,对WPES的准确性和适应性进行了精度检验和χ2检验分析。2种方法对3个年龄段直径分布的拟合精度分别为:84%、85%、85%和78%、64%、67%;χ2种检验统计量分别为7.17、8.73、2.40和52.62、45.31、7.96。分析结果表明,WPES的拟合精度较高,比MLE高5%-20%;WPES对不同时间和空间的适应性较强,其变动幅度是MLE的1/10。 展开更多
关键词 林分直径分布 Weibull分布参数 人工神经网络 Weibull参数估计系统 最大似然估计
在线阅读 下载PDF
基于双星定位系统的近地卫星定轨精度仿真 被引量:9
6
作者 赵德勇 潘晓刚 +2 位作者 王炯琦 周海银 王正明 《系统仿真学报》 EI CAS CSCD 北大核心 2006年第6期1437-1441,共5页
通过对测距误差特性的统计分析,建立了用于近地卫星精密定轨的距离和观测数据仿真方法,在此基础上构建了基于卫星动力学方程的精密定轨模型,设计了一种基于数值融合法的精密定轨改进算法和测距系统误差参数估计算法,并进行了六类仿真实... 通过对测距误差特性的统计分析,建立了用于近地卫星精密定轨的距离和观测数据仿真方法,在此基础上构建了基于卫星动力学方程的精密定轨模型,设计了一种基于数值融合法的精密定轨改进算法和测距系统误差参数估计算法,并进行了六类仿真实验。仿真计算结果表明,基于一天的距离和观测数据仿真计算得到的近地卫星定轨精度可以达到15.98米,与利用其他精密定轨软件系统在相同仿真条件下得到的近地卫星定轨精度基本相当,但该算法避免求解状态转移矩阵,具有计算速度快,稳健性好等特点。 展开更多
关键词 精密定轨 测距误差仿真 数值融合算法 系统误差参数估计
在线阅读 下载PDF
Learning the parameters of a class of stochastic Lotka-Volterra systems with neural networks
7
作者 WANG Zhanpeng WANG Lijin 《中国科学院大学学报(中英文)》 北大核心 2025年第1期20-25,共6页
In this paper,we propose a neural network approach to learn the parameters of a class of stochastic Lotka-Volterra systems.Approximations of the mean and covariance matrix of the observational variables are obtained f... In this paper,we propose a neural network approach to learn the parameters of a class of stochastic Lotka-Volterra systems.Approximations of the mean and covariance matrix of the observational variables are obtained from the Euler-Maruyama discretization of the underlying stochastic differential equations(SDEs),based on which the loss function is built.The stochastic gradient descent method is applied in the neural network training.Numerical experiments demonstrate the effectiveness of our method. 展开更多
关键词 stochastic Lotka-Volterra systems neural networks Euler-Maruyama scheme parameter estimation
在线阅读 下载PDF
基于最小二乘的准同步DFT幅值线性修正方法 被引量:10
8
作者 傅中君 王建宇 +3 位作者 欧云 周根元 赵小荣 洑涵妤 《电子测量与仪器学报》 CSCD 北大核心 2019年第7期72-78,共7页
准同步离散傅里叶变换(DFT)谐波分析频谱泄漏的主要原因是信号频偏导致的短范围泄漏。在分析准同步DFT短范围泄露特性的基础上,给出了基于最小二乘原理的准同步DFT幅值线性修正方法。该方法的具体思路是构建基波幅值误差曲线,采用最小... 准同步离散傅里叶变换(DFT)谐波分析频谱泄漏的主要原因是信号频偏导致的短范围泄漏。在分析准同步DFT短范围泄露特性的基础上,给出了基于最小二乘原理的准同步DFT幅值线性修正方法。该方法的具体思路是构建基波幅值误差曲线,采用最小二乘法得到基波幅值误差的线性修正方程,推广基波幅值误差线性修正方程到高次谐波,获得高次谐波幅值误差的线性修正方程。仿真实验表明,准同步DFT幅值线性修正方法既能够获得高精度的幅值分析结果,又能够降低算法复杂度,实现实时运算。 展开更多
关键词 谐波分析 傅里叶变换 电力系统参数估计 频谱分析 准同步采样
在线阅读 下载PDF
Modeling and parameter estimation for hydraulic system of excavator's arm 被引量:9
9
作者 何清华 郝鹏 张大庆 《Journal of Central South University of Technology》 2008年第3期382-386,共5页
A retrofitted electro-hydraulic proportional system for hydraulic excavator was introduced firstly. According to the principle and characteristic of load independent flow distribution(LUDV) system,taking boom hydrauli... A retrofitted electro-hydraulic proportional system for hydraulic excavator was introduced firstly. According to the principle and characteristic of load independent flow distribution(LUDV) system,taking boom hydraulic system as an example and ignoring the leakage of hydraulic cylinder and the mass of oil in it,a force equilibrium equation and a continuous equation of hydraulic cylinder were set up. Based on the flow equation of electro-hydraulic proportional valve,the pressure passing through the valve and the difference of pressure were tested and analyzed. The results show that the difference of pressure does not change with load,and it approximates to 2.0 MPa. And then,assume the flow across the valve is directly proportional to spool displacement and is not influenced by load,a simplified model of electro-hydraulic system was put forward. At the same time,by analyzing the structure and load-bearing of boom instrument,and combining moment equivalent equation of manipulator with rotating law,the estimation methods and equations for such parameters as equivalent mass and bearing force of hydraulic cylinder were set up. Finally,the step response of flow of boom cylinder was tested when the electro-hydraulic proportional valve was controlled by the step current. Based on the experiment curve,the flow gain coefficient of valve is identified as 2.825×10-4 m3/(s·A) and the model is verified. 展开更多
关键词 EXCAVATOR electro-hydraulic proportional system load independent flow distribution(LUDV) system MODELING parameter estimation
在线阅读 下载PDF
Design of motion control of dam safety inspection underwater vehicle 被引量:5
10
作者 孙玉山 万磊 +2 位作者 甘永 王建国 姜春萌 《Journal of Central South University》 SCIE EI CAS 2012年第6期1522-1529,共8页
Plenty of dams in China are in danger while there are few effective methods for underwater dam inspections of hidden problems such as conduits,cracks and inanitions.The dam safety inspection remotely operated vehicle(... Plenty of dams in China are in danger while there are few effective methods for underwater dam inspections of hidden problems such as conduits,cracks and inanitions.The dam safety inspection remotely operated vehicle(DSIROV) is designed to solve these problems which can be equipped with many advanced sensors such as acoustical,optical and electrical sensors for underwater dam inspection.A least-square parameter estimation method is utilized to estimate the hydrodynamic coefficients of DSIROV,and a four degree-of-freedom(DOF) simulation system is constructed.The architecture of DSIROV's motion control system is introduced,which includes hardware and software structures.The hardware based on PC104 BUS,uses AMD ELAN520 as the controller's embedded CPU and all control modules work in VxWorks real-time operating system.Information flow of the motion system of DSIROV,automatic control of dam scanning and dead-reckoning algorithm for navigation are also discussed.The reliability of DSIROV's control system can be verified and the control system can fulfill the motion control mission because embankment checking can be demonstrated by the lake trials. 展开更多
关键词 dam safety inspection remotely operated vehicle (DSIROV) control system architecture embedded system automaticcontrol of dam-scanning dead-reckoning
在线阅读 下载PDF
Unbiased parameter estimation of continuous-time system based on modulating functions with input and output white noises
11
作者 贺尚红 李旭宇 《Journal of Central South University》 SCIE EI CAS 2011年第3期773-781,共9页
An efficient unbiased estimation method is proposed for the direct identification of linear continuous-time system with noisy input and output measurements.Using the Gaussian modulating filters,by numerical integratio... An efficient unbiased estimation method is proposed for the direct identification of linear continuous-time system with noisy input and output measurements.Using the Gaussian modulating filters,by numerical integration,an equivalent discrete identification model which is parameterized with continuous-time model parameters is developed,and the parameters can be estimated by the least-squares (LS) algorithm.Even with white noises in input and output measurement data,the LS estimate is biased,and the bias is determined by the variances of noises.According to the asymptotic analysis,the relationship between bias and noise variances is derived.One equation relating to the measurement noise variances is derived through the analysis of the LS errors.Increasing the degree of denominator of the system transfer function by one,an extended model is constructed.By comparing the true value and LS estimates of the parameters between original and extended model,another equation with input and output noise variances is formulated.So,the noise variances are resolved by the set of equations,the LS bias is eliminated and the unbiased estimates of system parameters are obtained.A simulation example by comparing the standard LS with bias eliminating LS algorithm indicates that the proposed algorithm is an efficient method with noisy input and output measurements. 展开更多
关键词 continuous-time system unbiased parameter modulating functions noise
在线阅读 下载PDF
上一页 1 下一页 到第
使用帮助 返回顶部