Energy consumption of block-cutting machines represents a major cost item in the processing of travertines and other natural stones. Therefore, determining the optimum sawing conditions for a particular stone is of ma...Energy consumption of block-cutting machines represents a major cost item in the processing of travertines and other natural stones. Therefore, determining the optimum sawing conditions for a particular stone is of major importance in the natural stone-processing industry. An experimental study was carried out utilizing a fully instrumented block-cutter to investigate the sawing performances of five different types of travertine blocks during cutting with a circular diamond saw. The sawing tests were performed in the down-cutting mode. Performance measurements were determined by measuring the cutting speed and energy consumption. Then, specific energy was determined. The one main cutting parameter, cutting speed, was varied in the investigation of optimum cutting performance. Furthermore, some physico-mechanical properties of file travertine blocks were determined in the laboratory. As a result, it is found that the energy consumption （specific energy） of block cutting machines is highly affected by cutting speed. It is determined that specific energy value usually decreases when cutting speed increases. When the cutting speed is higher than the determined value, the diamond saw can become stuck in the travertine block; this situation can be a problem for the block-cutting machine. As a result, the optimum cutting speed obtained for the travertine mines examined is approximately 1.5-2.0 m/min.展开更多
The mechanical properties and stress corrosion cracking （SCC） resistance of an Al-Zn-Cu-Mg-Sc-Zr alloy under different aging conditions were investigated. The dependence of microstrueture and mechanical properties o...The mechanical properties and stress corrosion cracking （SCC） resistance of an Al-Zn-Cu-Mg-Sc-Zr alloy under different aging conditions were investigated. The dependence of microstrueture and mechanical properties on aging parameters was evaluated by tensile test, hardness test and conductivity measurement. The results show that for the alloys with retrogression and re-aging treatment （RRA）, the conductivity increases with the retrogression time and temperature, while the tensile strength decreases. The transmission electron microscopy （TEM） results show that the precipitates η（MgZn2） at grain boundary aggregate apparently with retrogression time and the precipitates inside the matrix exhibit the similar distribution to T6 temper, which comprises fine GP zones, large η＇（MgZn2）and η（MgZn2） phases. According to the mechanical properties and microstructure observations, the optimal RRA regime is recommended to be 120℃, 24h ＋ 180 ℃, 30 min ＋ 120 ℃, 24 h. The strength level of the alloy after the optimum RRA treatment is similar to that in T6 condition and the SCC resistance is improved obviously in contrast to T6 condition.展开更多
An incrementally nonlinear hypoplastic constitutive model was introduced, which was developed without recourse to the concepts in elastoplasticity theory such as yield surface, plastic potential and the decomposition ...An incrementally nonlinear hypoplastic constitutive model was introduced, which was developed without recourse to the concepts in elastoplasticity theory such as yield surface, plastic potential and the decomposition of the deformation into elastic and plastic parts. Triaxial drained tests on rockfill were conducted on a large scale triaxial apparatus under two types of stress paths, which were the stress paths of constant stress ratio and the complex stress paths with transitional features. Motivated by the effect of stress path, the Gudehus-Bauer hypoplastic model was improved by considering the parameter variations with different ratios of stress increment. Fitting parameter a presents a piecewise linear relationship with cosine of the slope angle θ determined by instantaneous stress path. The improved hypoplastic model can present peak stress increasing and volumetric strain changing from dilatancy to contractancy with the increase of transitional confining pressure σ3t and the decrease of slope angle θ of stress path. Compared with the test data, it is shown that the model is capable of fully considering the effect of stress path on rockfill.展开更多
Grinding is one of the most costly operations in the mechanical breaking and mining.Determination of the breakage characteristics and preconditioning is important to increase the grinding efficiency.Investigations of ...Grinding is one of the most costly operations in the mechanical breaking and mining.Determination of the breakage characteristics and preconditioning is important to increase the grinding efficiency.Investigations of the seismic,mechanical and breakage properties of iron oxides are very important parameters for investigating the rock fragmentation by blasting and comminution processes in iron ore mines.In this paper,at first,geomechanical and seismic properties of the oxide ores(magnetite and hematite)in the Chadormalu iron ore mine were studied.The results showed that the percentage of magnetite has a direct relationship with uniaxial compressive strength,tensile strength and P and S wave’s velocities and has an inverse relationship with Poisson ratio and porosity.Moreover,to study breakage and preconditioning characteristics in the iron ores,two samples with different magnetite percents were blasted by detonation cord.The results showed that with higher percentage of magnetite,the number of fractures induced by blasting increased.Bond work index and magnetite percent were investigated in the 430 blasts in the mine.This investigation not only confirmed the small scale blasting results,but also showed that increasing the magnetite percent up to 50%noticeably reduces Bond work index and energy consumption in the grinding process.Also,the relationship between muck pile fragmentation and magnetite percentage were studied for several blasts that had the same blast pattern parameters and similar geology conditions.These results also confirmed precedents conclusions regarding magnetite percent and preconditioning relationship.展开更多
文摘Energy consumption of block-cutting machines represents a major cost item in the processing of travertines and other natural stones. Therefore, determining the optimum sawing conditions for a particular stone is of major importance in the natural stone-processing industry. An experimental study was carried out utilizing a fully instrumented block-cutter to investigate the sawing performances of five different types of travertine blocks during cutting with a circular diamond saw. The sawing tests were performed in the down-cutting mode. Performance measurements were determined by measuring the cutting speed and energy consumption. Then, specific energy was determined. The one main cutting parameter, cutting speed, was varied in the investigation of optimum cutting performance. Furthermore, some physico-mechanical properties of file travertine blocks were determined in the laboratory. As a result, it is found that the energy consumption （specific energy） of block cutting machines is highly affected by cutting speed. It is determined that specific energy value usually decreases when cutting speed increases. When the cutting speed is higher than the determined value, the diamond saw can become stuck in the travertine block; this situation can be a problem for the block-cutting machine. As a result, the optimum cutting speed obtained for the travertine mines examined is approximately 1.5-2.0 m/min.
基金Project(2006AA03Z523) supported by the National High-tech Research and Development Program of China
文摘The mechanical properties and stress corrosion cracking （SCC） resistance of an Al-Zn-Cu-Mg-Sc-Zr alloy under different aging conditions were investigated. The dependence of microstrueture and mechanical properties on aging parameters was evaluated by tensile test, hardness test and conductivity measurement. The results show that for the alloys with retrogression and re-aging treatment （RRA）, the conductivity increases with the retrogression time and temperature, while the tensile strength decreases. The transmission electron microscopy （TEM） results show that the precipitates η（MgZn2） at grain boundary aggregate apparently with retrogression time and the precipitates inside the matrix exhibit the similar distribution to T6 temper, which comprises fine GP zones, large η＇（MgZn2）and η（MgZn2） phases. According to the mechanical properties and microstructure observations, the optimal RRA regime is recommended to be 120℃, 24h ＋ 180 ℃, 30 min ＋ 120 ℃, 24 h. The strength level of the alloy after the optimum RRA treatment is similar to that in T6 condition and the SCC resistance is improved obviously in contrast to T6 condition.
基金Projects(50479057, 50639060) supported by the National Natural Science Foundation of China
文摘An incrementally nonlinear hypoplastic constitutive model was introduced, which was developed without recourse to the concepts in elastoplasticity theory such as yield surface, plastic potential and the decomposition of the deformation into elastic and plastic parts. Triaxial drained tests on rockfill were conducted on a large scale triaxial apparatus under two types of stress paths, which were the stress paths of constant stress ratio and the complex stress paths with transitional features. Motivated by the effect of stress path, the Gudehus-Bauer hypoplastic model was improved by considering the parameter variations with different ratios of stress increment. Fitting parameter a presents a piecewise linear relationship with cosine of the slope angle θ determined by instantaneous stress path. The improved hypoplastic model can present peak stress increasing and volumetric strain changing from dilatancy to contractancy with the increase of transitional confining pressure σ3t and the decrease of slope angle θ of stress path. Compared with the test data, it is shown that the model is capable of fully considering the effect of stress path on rockfill.
文摘Grinding is one of the most costly operations in the mechanical breaking and mining.Determination of the breakage characteristics and preconditioning is important to increase the grinding efficiency.Investigations of the seismic,mechanical and breakage properties of iron oxides are very important parameters for investigating the rock fragmentation by blasting and comminution processes in iron ore mines.In this paper,at first,geomechanical and seismic properties of the oxide ores(magnetite and hematite)in the Chadormalu iron ore mine were studied.The results showed that the percentage of magnetite has a direct relationship with uniaxial compressive strength,tensile strength and P and S wave’s velocities and has an inverse relationship with Poisson ratio and porosity.Moreover,to study breakage and preconditioning characteristics in the iron ores,two samples with different magnetite percents were blasted by detonation cord.The results showed that with higher percentage of magnetite,the number of fractures induced by blasting increased.Bond work index and magnetite percent were investigated in the 430 blasts in the mine.This investigation not only confirmed the small scale blasting results,but also showed that increasing the magnetite percent up to 50%noticeably reduces Bond work index and energy consumption in the grinding process.Also,the relationship between muck pile fragmentation and magnetite percentage were studied for several blasts that had the same blast pattern parameters and similar geology conditions.These results also confirmed precedents conclusions regarding magnetite percent and preconditioning relationship.
