期刊文献+
共找到4篇文章
< 1 >
每页显示 20 50 100
控制电位还原法回收氯化浸出液中的贵金属 被引量:7
1
作者 胡意文 何强 +2 位作者 王日 汪秋雨 黄绍勇 《中国有色金属学报》 EI CAS CSCD 北大核心 2017年第3期621-628,共8页
以亚硫酸钠为还原剂,研究采用控制电位还原法回收氯化浸出液中的贵金属。结果表明:当控制金还原电位为530~550mV时,氯化浸出液中98%以上的Au将被还原沉淀至粗金粉中,同时Pt、Pd和Te基本不被还原沉淀,所得粗金粉中Au含量在98%以上,Se、Te... 以亚硫酸钠为还原剂,研究采用控制电位还原法回收氯化浸出液中的贵金属。结果表明:当控制金还原电位为530~550mV时,氯化浸出液中98%以上的Au将被还原沉淀至粗金粉中,同时Pt、Pd和Te基本不被还原沉淀,所得粗金粉中Au含量在98%以上,Se、Te、Cu和Pb等杂质的含量均低于0.10%(质量分数),而且该金还原电位对不同Au浓度或酸度的氯化浸出液都具有良好的适应性;然后当控制铂钯还原电位为390~420mV时,金还原后液中的Au、Pt和Pd将被还原沉淀至1mg/L以下,而Te基本不被还原,所得铂钯精矿中贵金属含量高、杂质含量少,且所确定的铂钯还原电位对不同铂钯浓度或酸度的金还原后液以及反应温度均具备较好的适应性。可见,通过控制电位还原,可将氯化浸出液中贵金属选择性沉淀并与其他元素初步分离。 展开更多
关键词 氯化浸出液 贵金属 电位 还原 亚硫酸钠
在线阅读 下载PDF
铅阳极泥氯化浸出液除氟研究 被引量:1
2
作者 钟扬 陈进中 +2 位作者 伍廉奎 曹华珍 郑国渠 《有色金属(冶炼部分)》 CAS 北大核心 2015年第10期14-17,共4页
选用氯化钠脱除铅阳极泥氯化浸出液中的氟硅酸和氟硅酸盐,考察了氯化钠加入量、反应时间、沉降时间、温度等对氟脱除率的影响。在最佳工艺条件下,浸出液中氟浓度可降至2.43g/L以下,除氟率达87.7%。除氟后溶液在蒸馏过程中不产生结晶物,... 选用氯化钠脱除铅阳极泥氯化浸出液中的氟硅酸和氟硅酸盐,考察了氯化钠加入量、反应时间、沉降时间、温度等对氟脱除率的影响。在最佳工艺条件下,浸出液中氟浓度可降至2.43g/L以下,除氟率达87.7%。除氟后溶液在蒸馏过程中不产生结晶物,避免蒸馏管道发生堵塞现象,馏出液中氟浓度均在3g/L以下,可以作为稀酸返回浸出。 展开更多
关键词 铅阳极泥 氯化浸出液 氯化 除氟
在线阅读 下载PDF
铅银渣氯化浸出液净化及有价金属回收试验 被引量:3
3
作者 周起帆 刘三平 王玉芳 《有色金属(冶炼部分)》 CAS 北大核心 2020年第9期5-11,共7页
采用净液-置换工艺处理铅银渣氯化浸出液并提取银、铅,重点研究了铅粉置换银、铁粉置换铅的工艺影响条件。结果表明:利用Fe3+易水解的特性,采用中和除铁,石灰调节溶液pH为4.0即可完全除铁,铅粉加入量为6 g/L,pH=1.5~2.5,温度60 ℃,置换... 采用净液-置换工艺处理铅银渣氯化浸出液并提取银、铅,重点研究了铅粉置换银、铁粉置换铅的工艺影响条件。结果表明:利用Fe3+易水解的特性,采用中和除铁,石灰调节溶液pH为4.0即可完全除铁,铅粉加入量为6 g/L,pH=1.5~2.5,温度60 ℃,置换时间40~60 min,在此条件下,银的置换率大于98%,溶液中残银浓度低于1 mg/L;两段逆流可以较完全置换出溶液中的铅,两段综合置换率为87.08%,最终置换产物含铅量>90%,满足精炼要求。 展开更多
关键词 氯化浸出液 置换 银除铁
在线阅读 下载PDF
Enhanced extraction of scandium and inhibiting of iron from acid leaching solution of red mud by D2EHPA and sodium chloride 被引量:4
4
作者 LIWang LIU Yue ZHU Xiao-bo 《Journal of Central South University》 SCIE EI CAS CSCD 2021年第10期3029-3039,共11页
D2EHPA(P204),tri-butyl-phosphate(TBP)and sodium chloride(NaCl)were attractive for selective extraction of scandium from acid leaching solution of red mud.The extraction parameters of P204 concentration(X_(P204)),NaCl ... D2EHPA(P204),tri-butyl-phosphate(TBP)and sodium chloride(NaCl)were attractive for selective extraction of scandium from acid leaching solution of red mud.The extraction parameters of P204 concentration(X_(P204)),NaCl concentration(C_(NaCl)),pH value,reaction time,stirring speed and O/A were investigated to extract scandium and separate iron from the acid leaching solution.The extraction mechanism was analyzed by Fourier transform infrared spectroscopy(FT-IR)and thermodynamic theory.The single-stage extraction efficiency of scandium,iron andβ(Sc/Fe)were 99.1%,9.4%and 1061.2,respectively,with C_(NaCl) of 75 g/L and XP204 of 0.75 at solution pH value of 1.2 and stirring speed of 200 r/min for 6 min,in which a good separation effect of scandium and iron was obtained.The vibration absorption peak Sc─O was contributed to the extraction of scandium with P204.The complex[FeCln]^(3−n) existed in the solution with adding NaCl into the acid leaching solution.The value of n was higher and the valence state of the complex[FeCln]^(3−n) was lower with an increase of chloride concentration,which restricts the extraction efficiency of iron with P204.The extraction of three stages in the counter-current simulation experiments was carried out according to the McCabe-Thiele diagram.Gibbs free energy change(ΔG)of−5.93 kJ/mol,enthalpy change(ΔH)of 23.45 kJ/mol and entropy change(ΔH)of 98.54 J/(mol·K)were obtained in the solvent extraction proces,which indicate that the extraction reaction is easily spontaneous and endothermic and a proper increase of temperature is conducive to the extraction of scandium. 展开更多
关键词 SCANDIUM selective extraction D2EHPA/sodium chloride leaching solution red mud
在线阅读 下载PDF
上一页 1 下一页 到第
使用帮助 返回顶部