期刊文献+
共找到7篇文章
< 1 >
每页显示 20 50 100
基于模流平衡的U型材挤出口模结构优化
1
作者 黄雪梅 柳和生 黄兴元 《高分子材料科学与工程》 EI CAS CSCD 北大核心 2024年第1期74-81,共8页
应用Polyflow软件分别建立了U型件模型、带内外气体辅助层厚度不同的U型件模型和U型件开口有倾角的模型。针对传统挤出、不同内外层辅助气体厚度、不同开口倾角下3种情况进行了数值模拟计算,并用Origin软件对部分结果进行了分析。研究发... 应用Polyflow软件分别建立了U型件模型、带内外气体辅助层厚度不同的U型件模型和U型件开口有倾角的模型。针对传统挤出、不同内外层辅助气体厚度、不同开口倾角下3种情况进行了数值模拟计算,并用Origin软件对部分结果进行了分析。研究发现,使用气体辅助技术比型腔结构优化更有利于模流平衡;当内外气体辅助层厚度不同时,内层气体层厚度偏大、外层气体层偏薄时,更有利于抑制U型件开口收缩的变形;而对口模开口臂倾斜角度的修正更有利于减小或调整U型件开口收缩的变形。 展开更多
关键词 模流平衡 挤出成型 U型件 优化设计 数值
在线阅读 下载PDF
塑料异型材口模构型要素对挤出形变的影响 被引量:1
2
作者 张广冬 郝昕玉 +1 位作者 袁铁军 宋树权 《工程塑料应用》 CAS CSCD 北大核心 2016年第8期83-87,共5页
塑料异型材的挤出胀大及其引起的不规则挤出形变,是异型材挤出制品尺寸控制的难点所在。针对此类问题,采用有限元方法研究了典型异型材口模构型要素如T型口模分支立臂位置、90°夹角L型口模过渡区域转角、L型口模两臂夹角等对挤出... 塑料异型材的挤出胀大及其引起的不规则挤出形变,是异型材挤出制品尺寸控制的难点所在。针对此类问题,采用有限元方法研究了典型异型材口模构型要素如T型口模分支立臂位置、90°夹角L型口模过渡区域转角、L型口模两臂夹角等对挤出形变和模流平衡的影响。结果表明,随T型口模分支立臂由挤出中心位置向右偏移,挤出后的型材挤出中心位置发生偏移,立臂顶端向右上变形,从而使得挤出形变加剧,需要在模具设计时将立臂顶端向挤出中心方向进行补偿。在90°夹角L型口模内外转角处设置过渡圆角,有助于模具出口处的模流平衡。L型异型材两臂夹角在挤出后变大,且初始设计夹角为60°和90°时变化较大,需要根据相关实验找出其初始设计夹角与挤出后的实际夹角对应关系,以便在模具设计过程中进行参照。上述研究结果对逆向挤出问题的求解、异型材挤出模具的设计和口模构型的确定有着一定的参考意义。 展开更多
关键词 挤出形变 构型 模流平衡 逆向挤出
在线阅读 下载PDF
类U形挤出模具优化设计 被引量:1
3
作者 张广冬 郝昕玉 林建平 《塑料》 CAS CSCD 北大核心 2010年第6期8-10,96,共4页
以类U形塑料异型材为例,比较传统挤出模具设计方法和基于iSIGHT的挤出模具优化设计方法的优缺点。首先根据传统的挤出模具设计方法,建立相应的几何模型和有限元模型,对传统方法存在的问题进行分析。然后以模流平衡系数为优化目标,使用iS... 以类U形塑料异型材为例,比较传统挤出模具设计方法和基于iSIGHT的挤出模具优化设计方法的优缺点。首先根据传统的挤出模具设计方法,建立相应的几何模型和有限元模型,对传统方法存在的问题进行分析。然后以模流平衡系数为优化目标,使用iSIGHT优化软件对传统方法设计的模具进行优化。最后用实验对优化的结果进行验证,由实验可知,基于iSIGHT的优化设计的模具达到了生产实践的要求。 展开更多
关键词 异型材 POLYFLOW ISIGHT 模流平衡 优化设计
在线阅读 下载PDF
工艺参数对挤出成型的影响分析 被引量:3
4
作者 张广冬 郝昕玉 《工程塑料应用》 CAS CSCD 北大核心 2014年第1期68-70,共3页
采用有限元方法分析了工艺参数中入口流量和壁面滑移对挤出成型的影响,特别是对挤出压力降,挤出胀大比以及模流平衡系数等重要指标的影响。结果表明,随着入口流量的增大,模流平衡系数增大,同时模具型腔内的压力降也线性增大。壁面滑移... 采用有限元方法分析了工艺参数中入口流量和壁面滑移对挤出成型的影响,特别是对挤出压力降,挤出胀大比以及模流平衡系数等重要指标的影响。结果表明,随着入口流量的增大,模流平衡系数增大,同时模具型腔内的压力降也线性增大。壁面滑移的存在有利于减小挤出模内的速度梯度,从而减小挤出胀大比和模流平衡系数。 展开更多
关键词 挤出成型 工艺参数 挤出胀大比 模流平衡系数
在线阅读 下载PDF
Alpha-reliable combined mean traffic equilibrium model with stochastic travel times 被引量:5
5
作者 张文义 关伟 +1 位作者 宋丽英 孙会君 《Journal of Central South University》 SCIE EI CAS 2013年第12期3770-3778,共9页
Based on the reliability budget and percentile travel time(PTT) concept, a new travel time index named combined mean travel time(CMTT) under stochastic traffic network was proposed. CMTT here was defined as the convex... Based on the reliability budget and percentile travel time(PTT) concept, a new travel time index named combined mean travel time(CMTT) under stochastic traffic network was proposed. CMTT here was defined as the convex combination of the conditional expectations of PTT-below and PTT-excess travel times. The former was designed as a risk-optimistic travel time index, and the latter was a risk-pessimistic one. Hence, CMTT was able to describe various routing risk-attitudes. The central idea of CMTT was comprehensively illustrated and the difference among the existing travel time indices was analyzed. The Wardropian combined mean traffic equilibrium(CMTE) model was formulated as a variational inequality and solved via an alternating direction algorithm nesting extra-gradient projection process. Some mathematical properties of CMTT and CMTE model were rigorously proved. Finally, a numerical example was performed to characterize the CMTE network. It is founded that that risk-pessimism is of more benefit to a modest(or low) congestion and risk network, however, it changes to be risk-optimism for a high congestion and risk network. 展开更多
关键词 travel behavior risk attitude travel time reliability combined mean travel time wardropian user equilibrium
在线阅读 下载PDF
Macro modeling and analysis of traffic flow with road width 被引量:4
6
作者 唐铁桥 李传耀 +1 位作者 黄海军 尚华艳 《Journal of Central South University》 SCIE EI CAS 2011年第5期1757-1764,共8页
The macro modeling and the solution of traffic flow with road width were investigated.Firstly,a new macro model with the consideration of road width was proposed.Secondly,the effects of road width on uniform flow and ... The macro modeling and the solution of traffic flow with road width were investigated.Firstly,a new macro model with the consideration of road width was proposed.Secondly,the effects of road width on uniform flow and small perturbation were studied.The analytical and numerical results show that widening (shrinking) road can enhance (reduce) the equilibrium speed and flow,and the increments (decrements) will increase with the absolute value of road width gradient.In addition,the numerical results illustrate that the new model can describe the effects of road width on the evolutions of uniform flow and small perturbation. 展开更多
关键词 traffic flow road width macro modeling PERTURBATION
在线阅读 下载PDF
Optimal design of auxiliary-teeth to solve circulation current reduction of permanent magnet linear synchronous motor 被引量:1
7
作者 JANG Ki-bong KIM Jee-hyun +1 位作者 AN Ho-jin KIM Gyu-tak 《Journal of Central South University》 SCIE EI CAS 2011年第3期690-696,共7页
A discontinuity of magnetic circuits according to the end effect is generated in the permanent magnet linear synchronous motor (PMLSM). Due to the unbalanced back electro-motive force (EMF) and impedance produced,... A discontinuity of magnetic circuits according to the end effect is generated in the permanent magnet linear synchronous motor (PMLSM). Due to the unbalanced back electro-motive force (EMF) and impedance produced, unbalanced current is generated. The cireulatin8 current, which is caused by a decrease in the thrust, is generated by the unbalanced current. The optimal design of auxiliary-teeth at the end of the mover was carried out to solve the unbalance of phase by using design of experiment (DOE), and compared with the basic model through finite element analysis (FEA). As a result, the auxiliary-teeth model compensates for the decrease of thrust caused by the unbalanced phase. Also, this model is proven to reduce the detent force by the vibration and noise of the PMLSM and copper loss caused by the circulating current. 展开更多
关键词 permanent magnet linear synchronous motor auxiliary-teeth circulation current end effect thrust reduction
在线阅读 下载PDF
上一页 1 下一页 到第
使用帮助 返回顶部