期刊文献+
共找到4篇文章
< 1 >
每页显示 20 50 100
25Cr3Mo低合金钢在模拟矿井水环境下的腐蚀磨损行为 被引量:2
1
作者 燕超 仝哲 +2 位作者 曾群锋 成跃 王一钢 《热加工工艺》 北大核心 2024年第21期106-113,共8页
以25Cr3Mo低合金钢为研究对象,探索酸性、中性及碱性三种模拟矿井水环境下,采煤机滑靴材料25Cr3Mo钢表面的腐蚀磨损损伤行为。通过分析摩擦系数曲线、磨损形貌、元素分布及其化学态,定量计算不同条件下的比磨损率,揭示采煤机滑靴在模拟... 以25Cr3Mo低合金钢为研究对象,探索酸性、中性及碱性三种模拟矿井水环境下,采煤机滑靴材料25Cr3Mo钢表面的腐蚀磨损损伤行为。通过分析摩擦系数曲线、磨损形貌、元素分布及其化学态,定量计算不同条件下的比磨损率,揭示采煤机滑靴在模拟矿井水下的损伤机理。结果表明:25Cr3Mo钢在酸性、中性矿井中的稳定摩擦系数约为0.15,而在碱性矿井水下稳定摩擦系数下降至0.10,均小于干摩擦环境下的摩擦系数(0.27)。三种模拟矿井水下,25Cr3Mo钢的比磨损率相较于干摩擦均可降低一个数量级,但模拟矿井水环境中,25Cr3Mo钢表面会形成大量腐蚀凹坑,最大深度可达3.42μm。在酸性和中性矿井水下,25Cr3Mo表面的腐蚀产物均为Fe_(3)O_(4),且酸性环境中的腐蚀产物层出现大量微裂纹,而碱性矿井水下腐蚀产物中既含有Fe_(3)O_(4),又有α-FeOOH和α-Fe_(2)O_(3)。 展开更多
关键词 25Cr3Mo钢 模拟矿井 干摩擦 腐蚀磨损性能 表面损伤
在线阅读 下载PDF
模拟矿井综合实践教学平台安全风险评价研究 被引量:7
2
作者 刘音 崔向峥 +2 位作者 高天 冯肖 刘洋 《实验技术与管理》 CAS 北大核心 2018年第9期265-269,共5页
该文从模拟矿井实训教学平台安全规章制度、仪器设备管理、人员管理等6个方面进行风险识别,建立了模拟矿井综合实践教学平台风险评价指标体系,结合模糊综合评价法得出平台模糊综合评价模型。以山东科技大学模拟矿井综合实习实训教学平... 该文从模拟矿井实训教学平台安全规章制度、仪器设备管理、人员管理等6个方面进行风险识别,建立了模拟矿井综合实践教学平台风险评价指标体系,结合模糊综合评价法得出平台模糊综合评价模型。以山东科技大学模拟矿井综合实习实训教学平台为例进行了风险评价实证研究,根据综合评价结果对存在的安全隐患提出相应的整改措施。 展开更多
关键词 模拟矿井 综合实践教学平台 安全风险评价 模糊综合评价 整改措施
在线阅读 下载PDF
模拟矿井环境下的PEEK/SiO_(2)/CF-MoS_(2)复合材料摩擦行为研究
3
作者 冯存傲 陶若兰 +2 位作者 余振洋 陈凯 张德坤 《润滑与密封》 CAS CSCD 北大核心 2022年第11期47-58,共12页
为改善聚醚醚酮(PEEK)在矿井工况下的摩擦性能,选用纳米二氧化硅(Si O_(2))、二硫化钼(MoS_(2))和短切碳纤维(CF)为增强填料制备PEEK/Si O_(2)/CF-MoS_(2)复合材料,并探究PEEK/Si O_(2)/CF-MoS_(2)复合材料在不同工况条件下的滑动与滚... 为改善聚醚醚酮(PEEK)在矿井工况下的摩擦性能,选用纳米二氧化硅(Si O_(2))、二硫化钼(MoS_(2))和短切碳纤维(CF)为增强填料制备PEEK/Si O_(2)/CF-MoS_(2)复合材料,并探究PEEK/Si O_(2)/CF-MoS_(2)复合材料在不同工况条件下的滑动与滚动摩擦学性能;通过模拟滚轮罐耳在矿井环境下的运行方式,分析其磨损形貌和磨损机制。结果表明:PEEK/SiO_(2)/CF-MoS_(2)复合材料在不同载荷条件下均具有良好的减摩和耐磨特性;滑动摩擦在水介质工况下及滚动摩擦在干摩擦工况下,复合材料的摩擦因数和磨损率最低,其磨损机制均以磨粒磨损为主。与矿井常用的聚氨酯材料的对比,PEEK/SiO_(2)/CF-MoS_(2)复合材料的摩擦学性能更为优异。 展开更多
关键词 PEEK复合材料 滑动摩擦 滚动摩擦 模拟矿井环境
在线阅读 下载PDF
Experimental study and numerical simulation of spread law for fire on tunnel 被引量:3
4
作者 牛会永 乔晨露 +1 位作者 安敬鱼 邓军 《Journal of Central South University》 SCIE EI CAS CSCD 2015年第2期701-706,共6页
In order to research spread law and distribution law of temperature nearby fire sources on roadway in mine, according to combustion theory and other basic, the theory model of temperature attenuation was determined un... In order to research spread law and distribution law of temperature nearby fire sources on roadway in mine, according to combustion theory and other basic, the theory model of temperature attenuation was determined under unsteady heat-exchange between wind and roadway wall. The full-size roadway fire simulation experiments were carried out in Chongqing Research Institute of China Coal Technology & Engineering Group Corporation. The development processes of mine fire and flow pattern of high temperature gas were analyzed. Experimental roadway is seen as physical model, and through using CFD software, the processes of mine fire have been simulated on computer. The results show that, after fire occurs, if the wind speed is less than the minimum speed which can prevent smoke from rolling back, then the smaller wind speed can cause smoke to roll back easily. Hot plume will lead to secondary disasters in upwind side. Because of roadway wall, hot plume released from roadway fire zone has caused the occurrence of the ceiling jet, and the hot plume has been forced down. Whereas, owing to the higher temperature, buoyancy effect is more obvious. Therefore, smoke rises gradually along the roadway in the flow process, and the hierarchical interface appears wavy.Oxygen-enriched combustion and fuel-enriched combustion are the two kinds of combustion states of fire. The oxygen content of downwind side of fire is maintained at around 15% for oxygen-enriched combustion, and the oxygen content of downwind side of fire is maintained at around 2% for fuel-enriched combustion. Furthermore, fuel-enriched combustion can lead to secondary disasters easily. 展开更多
关键词 fire on roadway experiments of fire numerical simulation
在线阅读 下载PDF
上一页 1 下一页 到第
使用帮助 返回顶部