This work investigates the transient performance and stability of CO_(2)/H_(2)O co-electrolysis in an air-free environment using a flat-tube solid oxide electrolysis cell(SOEC)stack.The results showed that the transie...This work investigates the transient performance and stability of CO_(2)/H_(2)O co-electrolysis in an air-free environment using a flat-tube solid oxide electrolysis cell(SOEC)stack.The results showed that the transient behavior of the stack with and without blowing gas into the air electrode is almost the same.With a current density of 0.67 A·cm^(-2)@750℃,the stack operated for over 200 h under co-electrolysis conditions without air blowing,and the voltage drop rate of the stack was approximately 0.203%/100 hours.Microstructure analysis revealed a significant loss of nickel particles and an apparent for-mation of an insulating phase strontium chromate(SrCrO4)on the surface of the current collection layer of the air electrode,which are identified as key factors contributing to the performance degradation of the stack.This study provides a reference for development of efficient fuel preparation technology based on SOEC stack in airless environments.展开更多
Hollow-structured Cu_(0.3)Co_(2.7)O_(4) microspheres have been synthesized by a simple one-pot template-free hydrothermal method with copper sulfate,cobalt acetate and ammonia as raw materials.The products were charac...Hollow-structured Cu_(0.3)Co_(2.7)O_(4) microspheres have been synthesized by a simple one-pot template-free hydrothermal method with copper sulfate,cobalt acetate and ammonia as raw materials.The products were characterized by powder X-ray diffraction,energy dispersive X-ray analysis,selected area electron diffraction,high-resolution transmission electron microscopy,scanning electron microscopy and BET measurements.The research results show that the hollow Cu_(0.3)Co_(2.7)O_(4) microspheres consist of single-crystalline nanocubes with the diameter of about 20 nm.The formation mechanism of hollow Cu_(0.3)Co_(2.7)O_(4) microspheres is suggested as Ostwald ripening in a solid-solution-solid process,and Cu_(0.3)Co_(2.7)O_(4) microspheres are mesoporous containing two pore sizes of 3.3 and 5.9 nm.The as-prepared Cu_(0.3)Co_(2.7)O_(4) sensors have optimal gas responses to 50×10^(−6) mg/m^(3) C_(2)H_(5)OH at 190℃.展开更多
Electrolytic manganese residue leachate(EMRL)contains plenty of Mn^(2+) and NH_(4)^(+)-N,and phosphogypsum leachate(PGL)contains large amounts of PO_(4)^(3-)-P and F^(-).Traditional methods of EMRL and PGL discharge c...Electrolytic manganese residue leachate(EMRL)contains plenty of Mn^(2+) and NH_(4)^(+)-N,and phosphogypsum leachate(PGL)contains large amounts of PO_(4)^(3-)-P and F^(-).Traditional methods of EMRL and PGL discharge could seriously damage the ecological environment.In this study,an innovative method for cooperative removal Mn^(2+),NH_(4)^(+)-N,PO_(4)^(3-)-P,F^(-)from PG and POFT was studied.The result showed that Mn^(2+),PO_(4)^(3-)-P and F^(-)were mainly removed in forms of Mg_(3)Si_(4)O_(10)(OH)_(2),Mn_(3)O_(4),Mn_(3)(PO_(4))_(2),Mg_(3)(PO_(4))_(2),CaSO_(4)·2H_(2)O,MnF_(2),MnOOH and Ca_(2)P_(2)O_(7)·2H_(2)O,when LG-MgO was used to adjust the pH value of the system to 9.5,and the volume ratio of EMRL and PGL was 1:4,as well as reaction for 1 h at 25℃.NH_(4)^(+)-N was mainly removed by struvite precipitate,when the molar ratio of N:Mg:P was 1:3:2.4.The concentrations of Mn^(2+),NH_(4)^(+)-N and F^(-)were lower than the integrated wastewater discharge standard.The concentration of PO_(4)^(3-)-P decreased from 254.20 mg/L to 3.21 mg/L.This study provided a new method for EMRL and PGL cooperative harmless treatment.展开更多
A new style Ni-containing alumina ceramic foam based continuous three-dimensional interconnected skeleton was prepared by impregnating a polymeric sponge with aqueous ceramic slurry.Subsequently,alumina ceramic foam/s...A new style Ni-containing alumina ceramic foam based continuous three-dimensional interconnected skeleton was prepared by impregnating a polymeric sponge with aqueous ceramic slurry.Subsequently,alumina ceramic foam/steel metal matrix composites(MMCs) were prepared successfully by sand mold casting technique.The microstructure and mechanical properties of MMCs were investigated by SEM,EDS and compressive test.The results show that the depth of infiltration is about 40 μm to the bonding interface of ceramic/steel and the fracture strength σmax and plastic strain limit εp of composite are 520 MPa and 11.2%,respectively.The fretting wear mechanism of MMCs is mainly performed at the oxidative wear mode with lower load/friction frequency and the predominant oxidation wear together with slight adhesive wear and abrasive wear multiple mode with higher load/ friction frequency.Moreover,the infiltration bonding and continuous three-dimensional interconnected ceramic skeleton play a vital role in the stability of the bonding interface and excellent mechanical properties.展开更多
Oxygen-free copper and pre-metalized graphite were brazed using CuNiSnP braze alloy by high frequency induction heating method. Interracial microstructures and reaction phases were analyzed by scanning electron micros...Oxygen-free copper and pre-metalized graphite were brazed using CuNiSnP braze alloy by high frequency induction heating method. Interracial microstructures and reaction phases were analyzed by scanning electron microscopy （SEM） and energy dispersive X-ray spectroscopy （EDS）. The strength and resistance of the joints were tested. It is found that when the brazing parameters are optimized, the structures of the joints are graphite/（Cu,Ni）/Ni（s.s）＋NixPy/Cu3P＋Cu（s.s） （including Sn）＋eutectic structures （Cu3P＋Ni3P＋Cu（s.s）/Cu （s.s）/Cu）. When the temperature increases to 750℃ or the holding time prolongs to 300 s, the eutectie structures disappear and the amount of Cu3P increases. The maximum shear strength of the joints is 5.2 MPa, which fracture at the interface of graphite and metallization. The resistance of the joints is no more than 5 mΩ.展开更多
基金co-supported by the National Key R&D Program of China(No.2022YFB4002203)Baima Lake Laboratory Joint Funds of the Zhejiang Provincial Natural Science Foundation of China(No.LBMHY24B060003)Ningbo Key R&D Project(No.2023Z155).
文摘This work investigates the transient performance and stability of CO_(2)/H_(2)O co-electrolysis in an air-free environment using a flat-tube solid oxide electrolysis cell(SOEC)stack.The results showed that the transient behavior of the stack with and without blowing gas into the air electrode is almost the same.With a current density of 0.67 A·cm^(-2)@750℃,the stack operated for over 200 h under co-electrolysis conditions without air blowing,and the voltage drop rate of the stack was approximately 0.203%/100 hours.Microstructure analysis revealed a significant loss of nickel particles and an apparent for-mation of an insulating phase strontium chromate(SrCrO4)on the surface of the current collection layer of the air electrode,which are identified as key factors contributing to the performance degradation of the stack.This study provides a reference for development of efficient fuel preparation technology based on SOEC stack in airless environments.
基金Project(51202066)supported by the National Natural Science Foundation of ChinaProject(NCET-13-0784)supported by the Program for New Century Excellent Talents in University of China。
文摘Hollow-structured Cu_(0.3)Co_(2.7)O_(4) microspheres have been synthesized by a simple one-pot template-free hydrothermal method with copper sulfate,cobalt acetate and ammonia as raw materials.The products were characterized by powder X-ray diffraction,energy dispersive X-ray analysis,selected area electron diffraction,high-resolution transmission electron microscopy,scanning electron microscopy and BET measurements.The research results show that the hollow Cu_(0.3)Co_(2.7)O_(4) microspheres consist of single-crystalline nanocubes with the diameter of about 20 nm.The formation mechanism of hollow Cu_(0.3)Co_(2.7)O_(4) microspheres is suggested as Ostwald ripening in a solid-solution-solid process,and Cu_(0.3)Co_(2.7)O_(4) microspheres are mesoporous containing two pore sizes of 3.3 and 5.9 nm.The as-prepared Cu_(0.3)Co_(2.7)O_(4) sensors have optimal gas responses to 50×10^(−6) mg/m^(3) C_(2)H_(5)OH at 190℃.
基金Project(2018YFC1903500)supported by the National Key Research and Development Program of ChinaProject(52174386)supported by the National Natural Science Foundation of ChinaProject(2021YFH0058)supported by the Science and Technology Plan Project of Sichuan Province,China。
文摘Electrolytic manganese residue leachate(EMRL)contains plenty of Mn^(2+) and NH_(4)^(+)-N,and phosphogypsum leachate(PGL)contains large amounts of PO_(4)^(3-)-P and F^(-).Traditional methods of EMRL and PGL discharge could seriously damage the ecological environment.In this study,an innovative method for cooperative removal Mn^(2+),NH_(4)^(+)-N,PO_(4)^(3-)-P,F^(-)from PG and POFT was studied.The result showed that Mn^(2+),PO_(4)^(3-)-P and F^(-)were mainly removed in forms of Mg_(3)Si_(4)O_(10)(OH)_(2),Mn_(3)O_(4),Mn_(3)(PO_(4))_(2),Mg_(3)(PO_(4))_(2),CaSO_(4)·2H_(2)O,MnF_(2),MnOOH and Ca_(2)P_(2)O_(7)·2H_(2)O,when LG-MgO was used to adjust the pH value of the system to 9.5,and the volume ratio of EMRL and PGL was 1:4,as well as reaction for 1 h at 25℃.NH_(4)^(+)-N was mainly removed by struvite precipitate,when the molar ratio of N:Mg:P was 1:3:2.4.The concentrations of Mn^(2+),NH_(4)^(+)-N and F^(-)were lower than the integrated wastewater discharge standard.The concentration of PO_(4)^(3-)-P decreased from 254.20 mg/L to 3.21 mg/L.This study provided a new method for EMRL and PGL cooperative harmless treatment.
基金Project(51271080) supported by the National Natural Science Foundation of ChinaProject(2012JSSPITP1968) supported by the Innovative Foundation for Students of Jiangsu Province,ChinaProject(CKJB201204) supported by the Innovation Fund of Nanjing Institute of Technology,China
文摘A new style Ni-containing alumina ceramic foam based continuous three-dimensional interconnected skeleton was prepared by impregnating a polymeric sponge with aqueous ceramic slurry.Subsequently,alumina ceramic foam/steel metal matrix composites(MMCs) were prepared successfully by sand mold casting technique.The microstructure and mechanical properties of MMCs were investigated by SEM,EDS and compressive test.The results show that the depth of infiltration is about 40 μm to the bonding interface of ceramic/steel and the fracture strength σmax and plastic strain limit εp of composite are 520 MPa and 11.2%,respectively.The fretting wear mechanism of MMCs is mainly performed at the oxidative wear mode with lower load/friction frequency and the predominant oxidation wear together with slight adhesive wear and abrasive wear multiple mode with higher load/ friction frequency.Moreover,the infiltration bonding and continuous three-dimensional interconnected ceramic skeleton play a vital role in the stability of the bonding interface and excellent mechanical properties.
基金Project(50705022) supported by the National Natural Science Foundation of ChinaProject supported by the Program for New Century Excellent Talents in University
文摘Oxygen-free copper and pre-metalized graphite were brazed using CuNiSnP braze alloy by high frequency induction heating method. Interracial microstructures and reaction phases were analyzed by scanning electron microscopy （SEM） and energy dispersive X-ray spectroscopy （EDS）. The strength and resistance of the joints were tested. It is found that when the brazing parameters are optimized, the structures of the joints are graphite/（Cu,Ni）/Ni（s.s）＋NixPy/Cu3P＋Cu（s.s） （including Sn）＋eutectic structures （Cu3P＋Ni3P＋Cu（s.s）/Cu （s.s）/Cu）. When the temperature increases to 750℃ or the holding time prolongs to 300 s, the eutectie structures disappear and the amount of Cu3P increases. The maximum shear strength of the joints is 5.2 MPa, which fracture at the interface of graphite and metallization. The resistance of the joints is no more than 5 mΩ.
