Based on RNG k-ε turbulence model and sliding grid technique, solid-liquid two-phase three-dimensional(3-D) unsteady turbulence of full passage in slurry pump was simulated by means of Fluent software. The effects of...Based on RNG k-ε turbulence model and sliding grid technique, solid-liquid two-phase three-dimensional(3-D) unsteady turbulence of full passage in slurry pump was simulated by means of Fluent software. The effects of unsteady flow characteristics on solid-liquid two-phase flow and pump performance were researched under design condition. The results show that clocking effect has a significant influence on the flow in pump, and the fluctuation of flow velocity and pressure is obvious, particularly near the volute tongue, at the position of small sections of volute and within diffuser. Clocking effect has a more influence on liquid-phase than on solid-phase, and the wake-jet structure of relative velocity of solid-phase is less obvious than liquid-phase near the volute tongue and the impeller passage outlet. The fluctuation of relative velocity of solid-phase flow is 7.6% smaller than liquid-phase flow at the impeller outlet on circular path. Head and radial forces of the impeller are 8.1% and 85.7% of fluctuation, respectively. The results provide a theoretical basis for further research for turbulence, improving efficient, reducing the hydraulic losses and wear. Finally, field tests were carried out to verify the operation and wear of slurry pump.展开更多
Numerical computation models of air cooling heat transfer and flow behaviors in triangular wavy fin channels(TWFC) were established with structural parameters of fins considered.The air side properties of heat transfe...Numerical computation models of air cooling heat transfer and flow behaviors in triangular wavy fin channels(TWFC) were established with structural parameters of fins considered.The air side properties of heat transfer coefficient and pressure drop are displayed with variable structural parameters of fins and inlet velocities of cooling air.Within the range of simulation,TWFC has the best comprehensive performance when inlet velocity vin=4-10 m/s.Compared with those of straight fins,the simulation results reveal that the triangular wavy fin channels are of higher heat transfer performances especially with the fin structural parameters of fin-height Fh=9.0 mm,fin-pitch Fp=2.5-3.0 mm,fin-wavelength λ=14.0-17.5 mm and fin-wave-amplitude A=1.0-1.2 mm.The correlations of both heat transfer factor and friction factor are presented,and the deviations from the experimental measurements are within 20%.展开更多
In order to overcome the defects of air-agitated seed precipitation, such as scaring, liquid short-(circuiting,) the three-dimension flow fields with different structure are numerically simulated by computational flui...In order to overcome the defects of air-agitated seed precipitation, such as scaring, liquid short-(circuiting,) the three-dimension flow fields with different structure are numerically simulated by computational fluid dynamics software. Euler/Euler approach was used to study the effects of structure on the flow field in the tank. Multi-fluid model, body-fitted coordinates and multi-block gird were adopted in the simulation. The simulating results are well consonant with the practical situations. The flow field is improved obviously when the flow velocity increases from (0.089m/s) to 0.1920.300m/s at the bottom of the optimized tank and therefore the scaring is reduced greatly in the industrial production. With a gathering sill, the problem of short-circuiting, which always appeares in the upper of the tank, can be solved very well.展开更多
TN248.5 2001042439DF/HF化学激光器喷管设计和数值模拟=Nozzle designand numerical simulation method of nozzle flow in DF/HF chemical lasers[刊,中]/袁圣付,华卫红,姜宗福,赵伊君(国防科技大学应用物理系.湖南,长沙(410073))//...TN248.5 2001042439DF/HF化学激光器喷管设计和数值模拟=Nozzle designand numerical simulation method of nozzle flow in DF/HF chemical lasers[刊,中]/袁圣付,华卫红,姜宗福,赵伊君(国防科技大学应用物理系.湖南,长沙(410073))//中国激光.-2001,28(1).-19-21简述了喷管作用和单个喷管型面设计中存在的问题,根据气动理论提出了一种喷管设计新方法;介绍了DF/HF激光器喷管流动数值模拟的控制方程、初边值条件和CS方法。参12(赵桂云)展开更多
To investigate airflow pattern and its impact on particle deposition, finite-volume based computational fluid dynamics （CFD） simulations were conducted in the diseased triple-bifitrcation airways. Computations were ...To investigate airflow pattern and its impact on particle deposition, finite-volume based computational fluid dynamics （CFD） simulations were conducted in the diseased triple-bifitrcation airways. Computations were carried out for twenty Reynolds numbers ranging from 100 to 2 000 in the step of 100. Particles in the size range of 1-10 μm were conducted. Two particle deposition mechanisms （gravitational sedimentation and inertial impaction） were considered. The results indicate that there are strong relationship between airflow structures and particle deposition patterns. Deposition efficiency is different for different particles in the whole range of the respiratory rates. Particles in different sizes can deposit at different sites. Smaller particles can be uniformly deposited at the inside wall of the considered model. Larger particles can be mainly deposited in the proximal bifurcations. Deposition fraction varies a lot for different inlet Reynolds numbers. For lower Reynolds numbers, deposition fraction is relatively small and varies a little with varying the diameters. For Reynolds number to target the aerosols at the specific site. higher Reynolds numbers, there is a most efficient diameter for each展开更多
基金Project(51375498)supported by the National Natural Science Foundation of China
文摘Based on RNG k-ε turbulence model and sliding grid technique, solid-liquid two-phase three-dimensional(3-D) unsteady turbulence of full passage in slurry pump was simulated by means of Fluent software. The effects of unsteady flow characteristics on solid-liquid two-phase flow and pump performance were researched under design condition. The results show that clocking effect has a significant influence on the flow in pump, and the fluctuation of flow velocity and pressure is obvious, particularly near the volute tongue, at the position of small sections of volute and within diffuser. Clocking effect has a more influence on liquid-phase than on solid-phase, and the wake-jet structure of relative velocity of solid-phase is less obvious than liquid-phase near the volute tongue and the impeller passage outlet. The fluctuation of relative velocity of solid-phase flow is 7.6% smaller than liquid-phase flow at the impeller outlet on circular path. Head and radial forces of the impeller are 8.1% and 85.7% of fluctuation, respectively. The results provide a theoretical basis for further research for turbulence, improving efficient, reducing the hydraulic losses and wear. Finally, field tests were carried out to verify the operation and wear of slurry pump.
基金Project(50976022) supported by the National Natural Science Foundation of ChinaProject(BY2011155) supported by the Provincial Science and Technology Innovation and Transformation of Achievements of Special Fund Project of Jiangsu Province,China
文摘Numerical computation models of air cooling heat transfer and flow behaviors in triangular wavy fin channels(TWFC) were established with structural parameters of fins considered.The air side properties of heat transfer coefficient and pressure drop are displayed with variable structural parameters of fins and inlet velocities of cooling air.Within the range of simulation,TWFC has the best comprehensive performance when inlet velocity vin=4-10 m/s.Compared with those of straight fins,the simulation results reveal that the triangular wavy fin channels are of higher heat transfer performances especially with the fin structural parameters of fin-height Fh=9.0 mm,fin-pitch Fp=2.5-3.0 mm,fin-wavelength λ=14.0-17.5 mm and fin-wave-amplitude A=1.0-1.2 mm.The correlations of both heat transfer factor and friction factor are presented,and the deviations from the experimental measurements are within 20%.
基金Project(030620) supported by the Dissertation Innovation Fund of Central South University
文摘In order to overcome the defects of air-agitated seed precipitation, such as scaring, liquid short-(circuiting,) the three-dimension flow fields with different structure are numerically simulated by computational fluid dynamics software. Euler/Euler approach was used to study the effects of structure on the flow field in the tank. Multi-fluid model, body-fitted coordinates and multi-block gird were adopted in the simulation. The simulating results are well consonant with the practical situations. The flow field is improved obviously when the flow velocity increases from (0.089m/s) to 0.1920.300m/s at the bottom of the optimized tank and therefore the scaring is reduced greatly in the industrial production. With a gathering sill, the problem of short-circuiting, which always appeares in the upper of the tank, can be solved very well.
文摘TN248.5 2001042439DF/HF化学激光器喷管设计和数值模拟=Nozzle designand numerical simulation method of nozzle flow in DF/HF chemical lasers[刊,中]/袁圣付,华卫红,姜宗福,赵伊君(国防科技大学应用物理系.湖南,长沙(410073))//中国激光.-2001,28(1).-19-21简述了喷管作用和单个喷管型面设计中存在的问题,根据气动理论提出了一种喷管设计新方法;介绍了DF/HF激光器喷管流动数值模拟的控制方程、初边值条件和CS方法。参12(赵桂云)
基金Project(51178466) supported by the National Natural Science Foundation of ChinaProject(200545) supported by the Foundation for the Author of National Excellent Doctoral Dissertation of ChinaProject(2011JQ006) supported by the Fundamental Research Funds of the Central Universities of China
文摘To investigate airflow pattern and its impact on particle deposition, finite-volume based computational fluid dynamics （CFD） simulations were conducted in the diseased triple-bifitrcation airways. Computations were carried out for twenty Reynolds numbers ranging from 100 to 2 000 in the step of 100. Particles in the size range of 1-10 μm were conducted. Two particle deposition mechanisms （gravitational sedimentation and inertial impaction） were considered. The results indicate that there are strong relationship between airflow structures and particle deposition patterns. Deposition efficiency is different for different particles in the whole range of the respiratory rates. Particles in different sizes can deposit at different sites. Smaller particles can be uniformly deposited at the inside wall of the considered model. Larger particles can be mainly deposited in the proximal bifurcations. Deposition fraction varies a lot for different inlet Reynolds numbers. For lower Reynolds numbers, deposition fraction is relatively small and varies a little with varying the diameters. For Reynolds number to target the aerosols at the specific site. higher Reynolds numbers, there is a most efficient diameter for each
