High density lanthanum hexaboride(LaB_(6))polycrystalline with(100)preferred orientation was prepared by spark plasma sintering(SPS)using LaB_(6) nanocubes as raw materials in this work.Microstructure and thermionic e...High density lanthanum hexaboride(LaB_(6))polycrystalline with(100)preferred orientation was prepared by spark plasma sintering(SPS)using LaB_(6) nanocubes as raw materials in this work.Microstructure and thermionic electron emission property of LaB_(6) polycrystalline were investigated detailedly.The results show that the LaB_(6) polycrystalline had a relative density of 95.8%,and there was a(100)preferred orientation on its surface normal to SPS pressing direction.The work function of LaB_(6) polycrystalline normal surface was only 2.73 eV,which was almost close to the theoretical work function of LaB_(6)(100)single crystal surface.The reasons for preferential orientation of LaB_(6) polycrystalline were analyzed.展开更多
Pre-heat treatment is a vital step before cold ring rolling and it has significant effect on the microstructure and mechanical properties of rolled rings.The 100Cr6 steel rings were subjected to pre-heat treatment and...Pre-heat treatment is a vital step before cold ring rolling and it has significant effect on the microstructure and mechanical properties of rolled rings.The 100Cr6 steel rings were subjected to pre-heat treatment and subsequent cold rolling process.Scanning electron microscopy and tensile tests were applied to investigate microstructure characteristic and mechanical property variations of 100Cr6 steel rings undergoing different pre-heat treatings.The results indicate that the average diameter of carbide particles,the tensile strength and hardness increase,while the elongation decreases with the decrease of cooling rate.The cooling rate has minor effect on the yield strength of sample.After cold ring rolling,the ferrite matrix shows a clear direction along the rolling direction.The distribution of cementite is more homogeneous and the cementite particles are finer.Meanwhile,the hardness of the rolled ring is higher than that before rolling.展开更多
This study presents a comprehensive comparison of the electro-osmosis treatments of heavy metal contaminated soil using electrokinetic geosynthetics(EKG)and iron electrodes in terms of both theoretical analysis and ex...This study presents a comprehensive comparison of the electro-osmosis treatments of heavy metal contaminated soil using electrokinetic geosynthetics(EKG)and iron electrodes in terms of both theoretical analysis and experimental research.The variation in the electrical parameters was analyzed,and the results show linear relationships between temperature and conductivity and between the soil and pore water conductivities.The average cathode contact resistance of iron is60%smaller than that of EKG,whereas the average anode contact resistance of EKG is56%smaller than that of iron.The values of the power consumption per unit mass of contaminants for EKG and iron are1.895and1.989kJ/g,respectively.After electro-osmosis,the number of soil pores increased,but the average area decreased,with an average area of0.9100–1.0504μm^2.Based on microstructure analysis,we obtained higher electroosmotic efficiency and realized the effective analysis and utilization between macroscopic and microscopic parameters.展开更多
The deformation behavior of a new Al-Zn-Cu-Mg-Sc-Zr alloy was investigated with compression tests in temperature range of 380?470 ℃ and strain rate range of 0.001-10 s-1 using Gleeble 1500 system, and the associated ...The deformation behavior of a new Al-Zn-Cu-Mg-Sc-Zr alloy was investigated with compression tests in temperature range of 380?470 ℃ and strain rate range of 0.001-10 s-1 using Gleeble 1500 system, and the associated microstructural evolutions were studied by metallographic microscopy and transmission electron microscopy. The results show that true stress—strain curves exhibit a peak stress, followed by a dynamic flow softening at low strains (ε<0.05). The stress decreases with increasing deformation temperature and decreasing strain rate, which can be represented by a Zener-Hollomon exponential equation with the activation energy for deformation of 157.9 kJ/mol. The substructure in the deformed specimens consists of few fine precipitates with equaixed polygonized subgrains in the elongated grains and developed serrations at the grain boundaries. The dynamic flow softening is attributed mainly to dynamic recovery and dynamic recrystallization.展开更多
ZnO-Bi2O3-based varistor ceramics doped with EU2O3 in a range from 0 to 0.4% were obtained by high-energy ball milling and fired at 900-1000 ℃ for 2 h. XRD and SEM were applied to determine the phases and microstruct...ZnO-Bi2O3-based varistor ceramics doped with EU2O3 in a range from 0 to 0.4% were obtained by high-energy ball milling and fired at 900-1000 ℃ for 2 h. XRD and SEM were applied to determine the phases and microstructure of the varistor ceramics. A DC parameter instrument was applied to investigate the electronic properties and V-I characteristics. The XRD analysis of Eu2O3-doped ZnO-Bi2O3-based varistor ceramics shows that the ZnO, Eu-containing Bi-rich, Zn7Sb2O12-type spinel and Zn2Bi3Sb3O14-type which is the pyrochlore phase are present. With increasing Eu2O3 content, the average size of ZnO grain firstly decreases and then increases. The grain boundary defect model was particularly used to explain the excellent nonlinearity of ZnO-Bi2O3-based varistor ceramics with the addition of0.1% Eu2O3 and sintered at 950 ℃.展开更多
An Al-3Ti-0.2C-1RE grain refiner was prepared by in-situ reaction method.The microstructure was investigated by optical microscopy(OM),scanning electron microscopy(SEM) equipped with energy-dispersive spectrometry(EDS...An Al-3Ti-0.2C-1RE grain refiner was prepared by in-situ reaction method.The microstructure was investigated by optical microscopy(OM),scanning electron microscopy(SEM) equipped with energy-dispersive spectrometry(EDS) and X-ray diffraction(XRD).The results show that the Al-3Ti-0.2C-1RE grain refiner is composed of α-Al,TiAl3,TiC and Ti2 Al20 Ce phases.Compared with Al-3Ti-0.2C refiner,the morphology of TiAl3 phase is changed and Ti2 Al20 Ce phases form with the addition of RE.Accordingly,the refining performance is improved.The phase forming process of the refiner is as follows: Blocky Ti2 Al20 Ce and fine blocky TiAl3 form in the melt at the initial stage of reaction,then the fine blocky TiAl3 gradually disappears,and the blocky Ti2 Al20 Ce grows bigger with the increase of holding time.The predominant mechanism to synthesize TiC particles is the reaction between high concentration of solute Ti atoms and graphite particles.展开更多
The preparation of microsized hematite powder from ferrous sulfate using microwave calcination was investigated based on the TG/DTG curves. The decomposition of industrial ferrous sulfate under air atmosphere was divi...The preparation of microsized hematite powder from ferrous sulfate using microwave calcination was investigated based on the TG/DTG curves. The decomposition of industrial ferrous sulfate under air atmosphere was divided into three stages, and a ferrous sulfate sample added with 15% Fe_2O_3 could strongly absorb microwave energy. Therefore, preparing hematite powder from ferrous sulfate using microwave calcination was feasible. Hematite was obtained under the following optimized conditions: calcination temperature, 850 °C; microwave power, 650 W; and sample amount, 40 g. The obtained hematite satisfied the first-grade quality requirements. The total ferrum value was more than 58%, and the total sulfur and phosphorus contents were less than 0.5% and 0.2%, respectively. X-ray powder diffraction and scanning electron microscopy were used to characterize the structure and morphology of microsized hematite powder. The particles were non-spherical in shape, and the average particle size distribution was 10.45 μm. This work provides new potential applications for waste ferrous sulfate.展开更多
The effects of low temperature thermo-mechanical treatment （LTTMT） on microstructures and mechanical properties of Ti-6Al-4V （TC4） alloy were studied by optical microscopy （OM）, tensile test, scanning electron m...The effects of low temperature thermo-mechanical treatment （LTTMT） on microstructures and mechanical properties of Ti-6Al-4V （TC4） alloy were studied by optical microscopy （OM）, tensile test, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The experimental results confirm that the strength of TC4 alloy can be improved obviously by LTTMT processing, which combines strain strengthening with aging strengthening. The effect of LTTMT on the alloy depends on the microstructure of the refined and dispersed a＋fl phase on the basis of high dislocation density by pre-deformation below recrystallization temperature. The tensile strength decreases with the increase of pre-deformation reduction. The optimal processing parameters of LTTMT for TC4 alloy are as follows： solution treatment at 900 ℃ for 15 min, pre-deformation in the range of 600-700 ℃ with a reduction of 35%, finally aging at 540 ℃ for 4 h followed by air-cooling.展开更多
The evolution of microstructure on aging of an （α＋β） titanium alloy （Ti-5A1-5Mo-5V-1Cr-1Fe） in the β and （α＋β） solution-treated and quenched conditions was investigated, The presence of very fine to phase...The evolution of microstructure on aging of an （α＋β） titanium alloy （Ti-5A1-5Mo-5V-1Cr-1Fe） in the β and （α＋β） solution-treated and quenched conditions was investigated, The presence of very fine to phase was detected by electron diffraction for samples aged below 400 ℃. The fine a aggregates are uniformly formed within fl grains by nucleating at the to particles or β/ω interfaces. At higher temperature, the formation of to phase is avoided and the a lamellae are precipitated at the preferred site of grain boundary and then within the matrix. The highest hardness values are found when the alloys are aged at 450 ℃ for fl condition and 350 ℃ for （α＋β） condition.展开更多
A novel Ti-based Ti-Mn composite anode used for electrolytic manganese dioxide(EMD) fabrication was developed by a two-step heating manganizing technique.The effects of sintering temperature on the manganized microstr...A novel Ti-based Ti-Mn composite anode used for electrolytic manganese dioxide(EMD) fabrication was developed by a two-step heating manganizing technique.The effects of sintering temperature on the manganized microstructure and the performance of the composite anode were studied by scanning electron microscopy(SEM),mechanical properties tests at room temperature and electrochemical methods.The results show that the thickness of the diffusion layer increases with the increase of sintering temperature up to 1 100 °C;whereas,the surface Mn content increases and reaches the maximum at 1 000 °C and then decreases thereafter.Lower surface Mn content is beneficial for the enhanced corrosion resistance and lowered open cell voltage in electrolytic process.The new anode prepared under the optimized conditions has been applied in industry and exhibits superior economic benefits to conventional Ti anodic materials.展开更多
Aging precipitation and solid solution heat treatment were carried out on three steels which have chromium content of 18%, manganese content of 12%, 15%, 18%, and nitrogen content of 0.43%, 0.53%, 0.67%, respectively....Aging precipitation and solid solution heat treatment were carried out on three steels which have chromium content of 18%, manganese content of 12%, 15%, 18%, and nitrogen content of 0.43%, 0.53%, 0.67%, respectively. The mechanisms of precipitation and solid solution of high nitrogen anstenitic stainless steel were studied using the scanning electron microscopy, transmission electron microscopy, electron probe micro analysis and mechanical testing. The results show that, Cr2N is the primary precipitate in the tested stainless steels instead of Cr23C6. Cr2N nucleates at austenitic grain boundaries and grows towards inner grains with a lameUar morphology. By means of pre-precipitation of Cr2N at 800 ~C, the microstructure of the steels at solid solution state can be refined, thus improving the strength and plasticity. After the proposed treatment, the tensile strength, the proof strength and the elongation of the tested steel reach 881 MPa, 542 MPa and 54%, respectively.展开更多
Alkali metal(Li, Na, K) doped ZnO powders were synthesized by solid-state reaction at different calcination temperatures and holding time. Effects of holding time and K sources on the infrared emissivity of ZnO were i...Alkali metal(Li, Na, K) doped ZnO powders were synthesized by solid-state reaction at different calcination temperatures and holding time. Effects of holding time and K sources on the infrared emissivity of ZnO were investigated. The structure and surface morphologies of samples were characterized by X-ray diffraction(XRD) and scanning electron microscopy(SEM). The UV-Vis absorption and infrared emissivities were investigated by a UV-Vis spectrophotometer and an infrared emissometer, respectively. XRD patterns confirm the wurtzite structure of the as prepared samples with single phase. Smooth grain surfaces are detected in all doped ZnO samples, while ZnO:Li and ZnO:Na present the aggregation of grains. The redshifts in the optical band-gap are observed in K-, Na-, and Li-doped ZnO with the values 3.150, 3.144, and 3.142 eV. Due to better crystalline quality, ZnO:K shows a lower emissivity than others. The emissivity of K-doped ZnO decreases to the minimum value(0.804), at 1200 °C and holding 2 h. Compared with KNO3 as K source, K2CO3 doped ZnO has lower emissivities.展开更多
Effect of holding time on microstructural developments and transformation of precipitates formed at the interface during transient liquid-phase bonding of a duplex stainless steel using a Ni-based amorphous insert all...Effect of holding time on microstructural developments and transformation of precipitates formed at the interface during transient liquid-phase bonding of a duplex stainless steel using a Ni-based amorphous insert alloy was studied. The experimental results reveal that the microstructure of the adjacent base metal varies clearly as a function of holding time. The migration of Cr and Ni elements and the → transformation seem to play relevant roles in this microstructure evolution. The scanning electron microscopy (SEM) and electron prob X-ray microanalysis (EPMA) results indicate the transformation of BN→BN and (N, Mo) boride→BN at the interface with the holding time of 60-1 800 s. N content changes with holding time increasing at locations at the interface might be a controlling factor contributing to this transformation.展开更多
Microarc oxidation （MAO） coatings were prepared on 2024 aluminum alloy in a Na2SiO3-KOH electrolyte with KNinO4 addition varying from 0 to 4 g/L. The microstructure and phases of the coatings were characterized by s...Microarc oxidation （MAO） coatings were prepared on 2024 aluminum alloy in a Na2SiO3-KOH electrolyte with KNinO4 addition varying from 0 to 4 g/L. The microstructure and phases of the coatings were characterized by scanning electron microscopy （SEM） and X-ray diffractometry （XRD）, respectively. The corrosion resistance of MAO coatings was evaluated by electrochemical potentiodynamic polarization in 5% （mass fraction） NaCl solution. The results show that when KMnO4 is added into base electrolyte, the growth speed of oxide coatings is increased obviously. The main phase of oxide coatings is Al2O3, and the contents of MnO2 and MnEA104 phases are increased at the top of oxide coatings with increasing the concentration of KMnO4. The solute elements participate in forming the oxide coatings. When a proper concentration of KMnO4 （2.5 g/L） is added into the base solution, the micropores of the MAO coatings are small and compact, and the corrosion resistance of oxide coatings is increased largely.展开更多
Poly （vinyl butyral） （PVB） hollow fiber membranes were fabricated via thermally induced phase separation （TIPS）. The effects of coagulation bath temperature （CBT） on the structure and performance of membranes ...Poly （vinyl butyral） （PVB） hollow fiber membranes were fabricated via thermally induced phase separation （TIPS）. The effects of coagulation bath temperature （CBT） on the structure and performance of membranes were investigated in detail. The morphologies of the membranes were studied by scanning electron microscopy （SEM）, the performances of water permeability, rejection, breaking strength and elongation were measured, respectively. The results indicate that all the membranes have the asymmetric morphology and the thickness of the skin layer decreases and the pore size of the outer layer increases with the increase of CBT. The permeability of membranes prepared at air gap 1.0 cm and take-up speed 0.253 m/s increases from 1.047×10-7 to 5.909×10-7 m3/（m2·s-kPa） with the CBT increasing from 20 ℃ to 40℃, and sharply increases to 35.226×10 7 m3/（m2.s.kPa）once the CBT arrives at 50 ℃. While the carbonic ink rejections have no significant decrease, totally exceed 98%, but that of acid-maleic acid copolymer greatly decreases with the increase of CBT. Both the breaking strength and elongation decrease with the increase of CBT.展开更多
Similar friction welded joints of AA-7005 aluminum rods were fabricated using different combinations of process parameters such as friction pressure(1.0, 1.5 and 2.0 MPa) and friction time(10, 15 and 20 s). Interfacia...Similar friction welded joints of AA-7005 aluminum rods were fabricated using different combinations of process parameters such as friction pressure(1.0, 1.5 and 2.0 MPa) and friction time(10, 15 and 20 s). Interfacial microstructure and formation of intermetallic compounds at the joint interface were evaluated via scanning electron microscopy(SEM) equipped with energy dispersive spectrum(EDS), and optical microscopy(OM). Microstructural observations reveal the formation of intermetallic phases during the welding process which cannot be extruded from the interface. Theses phases influence the tensile strength of the resultant joints. From the tensile characteristics viewpoint, the greatest tensile strength value of 365 MPa is obtained at 1.5 MPa and 15 s. Finally, the role of microstructural features on tensile strength of resultant joints is discussed.展开更多
Oxygen-free copper and pre-metalized graphite were brazed using CuNiSnP braze alloy by high frequency induction heating method. Interracial microstructures and reaction phases were analyzed by scanning electron micros...Oxygen-free copper and pre-metalized graphite were brazed using CuNiSnP braze alloy by high frequency induction heating method. Interracial microstructures and reaction phases were analyzed by scanning electron microscopy （SEM） and energy dispersive X-ray spectroscopy （EDS）. The strength and resistance of the joints were tested. It is found that when the brazing parameters are optimized, the structures of the joints are graphite/（Cu,Ni）/Ni（s.s）＋NixPy/Cu3P＋Cu（s.s） （including Sn）＋eutectic structures （Cu3P＋Ni3P＋Cu（s.s）/Cu （s.s）/Cu）. When the temperature increases to 750℃ or the holding time prolongs to 300 s, the eutectie structures disappear and the amount of Cu3P increases. The maximum shear strength of the joints is 5.2 MPa, which fracture at the interface of graphite and metallization. The resistance of the joints is no more than 5 mΩ.展开更多
Molybdenum disilicide(MoSi_2) based composites with various contents of carbon nanotubes(CNTs) were fabricated by spark plasma sintering(SPS) in vacuum under a pressure of 25 MPa.The composites obtained under a sinter...Molybdenum disilicide(MoSi_2) based composites with various contents of carbon nanotubes(CNTs) were fabricated by spark plasma sintering(SPS) in vacuum under a pressure of 25 MPa.The composites obtained under a sintering temperature of 1500 °C and time of 10 min exhibited optimum mechanical properties at room temperature in terms of fracture toughness and transverse rupture strength.MoSi_2 based composite with 6.0% CNTs(volume fraction) had the highest fracture toughness,transverse rupture strength and hardness,which were improved by about 25.7%,51.5% and 24.4% respectively,as compared with pure MoSi_2.A Mo_(4.8)Si_3C_(0.6) phase was detected in CNTs/MoSi_2 composites by both X-ray diffraction(XRD) method and microstructure analysis with scanning electron microscopy(SEM).It is believed that the fine grains and well dispersed small Mo_(4.8)Si_3C_(0.6) particles had led to a higher hardness and strength of CNTs/MoSi_2 composites because of their particle pullout,crack deflection and micro-bridging effects.展开更多
基金Project(51902342)supported by the National Natural Science Foundation of China。
文摘High density lanthanum hexaboride(LaB_(6))polycrystalline with(100)preferred orientation was prepared by spark plasma sintering(SPS)using LaB_(6) nanocubes as raw materials in this work.Microstructure and thermionic electron emission property of LaB_(6) polycrystalline were investigated detailedly.The results show that the LaB_(6) polycrystalline had a relative density of 95.8%,and there was a(100)preferred orientation on its surface normal to SPS pressing direction.The work function of LaB_(6) polycrystalline normal surface was only 2.73 eV,which was almost close to the theoretical work function of LaB_(6)(100)single crystal surface.The reasons for preferential orientation of LaB_(6) polycrystalline were analyzed.
基金Project(2011CB706605)supported by the National Basic Research Program of ChinaProject(2011CDA12)supported by the Innovative Research Groups of the Natural Science Foundation of Hubei Province,ChinaProjects(2012-Ia-017,2013-IV-014)supported by the Fundamental Research Funds for the Central Universities,China
文摘Pre-heat treatment is a vital step before cold ring rolling and it has significant effect on the microstructure and mechanical properties of rolled rings.The 100Cr6 steel rings were subjected to pre-heat treatment and subsequent cold rolling process.Scanning electron microscopy and tensile tests were applied to investigate microstructure characteristic and mechanical property variations of 100Cr6 steel rings undergoing different pre-heat treatings.The results indicate that the average diameter of carbide particles,the tensile strength and hardness increase,while the elongation decreases with the decrease of cooling rate.The cooling rate has minor effect on the yield strength of sample.After cold ring rolling,the ferrite matrix shows a clear direction along the rolling direction.The distribution of cementite is more homogeneous and the cementite particles are finer.Meanwhile,the hardness of the rolled ring is higher than that before rolling.
基金Project(51378469)supported by the National Natural Science Foundation of ChinaProject(2017C33034)supported by the Application Research of Public Welfare Technology in Zhejiang Province,China+1 种基金Project(LQ18E080001)supported by the Zhejiang Provincial Natural Science Foundation,ChinaProject(12017A610304)supported by the Natural Science Foundation of Ningbo City,China
文摘This study presents a comprehensive comparison of the electro-osmosis treatments of heavy metal contaminated soil using electrokinetic geosynthetics(EKG)and iron electrodes in terms of both theoretical analysis and experimental research.The variation in the electrical parameters was analyzed,and the results show linear relationships between temperature and conductivity and between the soil and pore water conductivities.The average cathode contact resistance of iron is60%smaller than that of EKG,whereas the average anode contact resistance of EKG is56%smaller than that of iron.The values of the power consumption per unit mass of contaminants for EKG and iron are1.895and1.989kJ/g,respectively.After electro-osmosis,the number of soil pores increased,but the average area decreased,with an average area of0.9100–1.0504μm^2.Based on microstructure analysis,we obtained higher electroosmotic efficiency and realized the effective analysis and utilization between macroscopic and microscopic parameters.
基金Project(2006AA03Z523) supported by the National High-Tech Research and Development Program of China
文摘The deformation behavior of a new Al-Zn-Cu-Mg-Sc-Zr alloy was investigated with compression tests in temperature range of 380?470 ℃ and strain rate range of 0.001-10 s-1 using Gleeble 1500 system, and the associated microstructural evolutions were studied by metallographic microscopy and transmission electron microscopy. The results show that true stress—strain curves exhibit a peak stress, followed by a dynamic flow softening at low strains (ε<0.05). The stress decreases with increasing deformation temperature and decreasing strain rate, which can be represented by a Zener-Hollomon exponential equation with the activation energy for deformation of 157.9 kJ/mol. The substructure in the deformed specimens consists of few fine precipitates with equaixed polygonized subgrains in the elongated grains and developed serrations at the grain boundaries. The dynamic flow softening is attributed mainly to dynamic recovery and dynamic recrystallization.
基金Projects(BK2011243,BK2012156) supported by the Natural Science Foundation of Jiangsu Province,ChinaProject(20123227120021) supported by the Specialized Research Fund for the Doctoral Program of Higher Education,China+3 种基金Project(KFJJ201105) supported by the Opening Project of State key Laboratory of Electronic Thin Films and Integrated Devices,ChinaProject(10KJD430002) supported by the Universities Natural Science Research Project of Jiangsu Province,ChinaProject(13KJB430006) supported by the Application Program for Basic Research of Changzhou,ChinaProject supported by the Industrial Center of Jiangsu University Undergraduate Practice-Innovation Training Project,China
文摘ZnO-Bi2O3-based varistor ceramics doped with EU2O3 in a range from 0 to 0.4% were obtained by high-energy ball milling and fired at 900-1000 ℃ for 2 h. XRD and SEM were applied to determine the phases and microstructure of the varistor ceramics. A DC parameter instrument was applied to investigate the electronic properties and V-I characteristics. The XRD analysis of Eu2O3-doped ZnO-Bi2O3-based varistor ceramics shows that the ZnO, Eu-containing Bi-rich, Zn7Sb2O12-type spinel and Zn2Bi3Sb3O14-type which is the pyrochlore phase are present. With increasing Eu2O3 content, the average size of ZnO grain firstly decreases and then increases. The grain boundary defect model was particularly used to explain the excellent nonlinearity of ZnO-Bi2O3-based varistor ceramics with the addition of0.1% Eu2O3 and sintered at 950 ℃.
基金Project(51174177)supported by the National Natural Science Foundation of China
文摘An Al-3Ti-0.2C-1RE grain refiner was prepared by in-situ reaction method.The microstructure was investigated by optical microscopy(OM),scanning electron microscopy(SEM) equipped with energy-dispersive spectrometry(EDS) and X-ray diffraction(XRD).The results show that the Al-3Ti-0.2C-1RE grain refiner is composed of α-Al,TiAl3,TiC and Ti2 Al20 Ce phases.Compared with Al-3Ti-0.2C refiner,the morphology of TiAl3 phase is changed and Ti2 Al20 Ce phases form with the addition of RE.Accordingly,the refining performance is improved.The phase forming process of the refiner is as follows: Blocky Ti2 Al20 Ce and fine blocky TiAl3 form in the melt at the initial stage of reaction,then the fine blocky TiAl3 gradually disappears,and the blocky Ti2 Al20 Ce grows bigger with the increase of holding time.The predominant mechanism to synthesize TiC particles is the reaction between high concentration of solute Ti atoms and graphite particles.
基金Project(2013AA064003)supported by the National Technology Research and Development Program of ChinaProject(51564033)supported by the National Natural Science Foundation of ChinaProject(2016FA023)supported by the Yunnan Applied Basic Research(CNMRCUXT1403)State Key Laboratory of Complex Nonferrous Metal Resources Clean Utilization,Kunming University of Science and Technology,China
文摘The preparation of microsized hematite powder from ferrous sulfate using microwave calcination was investigated based on the TG/DTG curves. The decomposition of industrial ferrous sulfate under air atmosphere was divided into three stages, and a ferrous sulfate sample added with 15% Fe_2O_3 could strongly absorb microwave energy. Therefore, preparing hematite powder from ferrous sulfate using microwave calcination was feasible. Hematite was obtained under the following optimized conditions: calcination temperature, 850 °C; microwave power, 650 W; and sample amount, 40 g. The obtained hematite satisfied the first-grade quality requirements. The total ferrum value was more than 58%, and the total sulfur and phosphorus contents were less than 0.5% and 0.2%, respectively. X-ray powder diffraction and scanning electron microscopy were used to characterize the structure and morphology of microsized hematite powder. The particles were non-spherical in shape, and the average particle size distribution was 10.45 μm. This work provides new potential applications for waste ferrous sulfate.
基金Project(2008WK2005) supported by the Science and Technology Plan of Hunan Province, China
文摘The effects of low temperature thermo-mechanical treatment （LTTMT） on microstructures and mechanical properties of Ti-6Al-4V （TC4） alloy were studied by optical microscopy （OM）, tensile test, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The experimental results confirm that the strength of TC4 alloy can be improved obviously by LTTMT processing, which combines strain strengthening with aging strengthening. The effect of LTTMT on the alloy depends on the microstructure of the refined and dispersed a＋fl phase on the basis of high dislocation density by pre-deformation below recrystallization temperature. The tensile strength decreases with the increase of pre-deformation reduction. The optimal processing parameters of LTTMT for TC4 alloy are as follows： solution treatment at 900 ℃ for 15 min, pre-deformation in the range of 600-700 ℃ with a reduction of 35%, finally aging at 540 ℃ for 4 h followed by air-cooling.
基金Project (50634030) supported by the National Natural Science Foundation of ChinaProject (2007DS04014) supported by the Program of Science and Technology of Shandong Province,ChinaProject supported by the Open Research Fund from the State Key Laboratory of Rolling and Automation,Northeastern University, China
文摘The evolution of microstructure on aging of an （α＋β） titanium alloy （Ti-5A1-5Mo-5V-1Cr-1Fe） in the β and （α＋β） solution-treated and quenched conditions was investigated, The presence of very fine to phase was detected by electron diffraction for samples aged below 400 ℃. The fine a aggregates are uniformly formed within fl grains by nucleating at the to particles or β/ω interfaces. At higher temperature, the formation of to phase is avoided and the a lamellae are precipitated at the preferred site of grain boundary and then within the matrix. The highest hardness values are found when the alloys are aged at 450 ℃ for fl condition and 350 ℃ for （α＋β） condition.
基金Projects(20476106,50721003 and 20636020) supported by the National Natural Science Foundation of ChinaProject(50825102) supported by the National Natural Science Funds for Distinguished Young Scholar of China+1 种基金Project(2006AA03Z511) supported by the National High Technology Research and Development Program of ChinaProject supported by the 111 Program of Chinese Ministry of Education
文摘A novel Ti-based Ti-Mn composite anode used for electrolytic manganese dioxide(EMD) fabrication was developed by a two-step heating manganizing technique.The effects of sintering temperature on the manganized microstructure and the performance of the composite anode were studied by scanning electron microscopy(SEM),mechanical properties tests at room temperature and electrochemical methods.The results show that the thickness of the diffusion layer increases with the increase of sintering temperature up to 1 100 °C;whereas,the surface Mn content increases and reaches the maximum at 1 000 °C and then decreases thereafter.Lower surface Mn content is beneficial for the enhanced corrosion resistance and lowered open cell voltage in electrolytic process.The new anode prepared under the optimized conditions has been applied in industry and exhibits superior economic benefits to conventional Ti anodic materials.
基金Project(50974014) supported by the National Natural Science Foundation of China
文摘Aging precipitation and solid solution heat treatment were carried out on three steels which have chromium content of 18%, manganese content of 12%, 15%, 18%, and nitrogen content of 0.43%, 0.53%, 0.67%, respectively. The mechanisms of precipitation and solid solution of high nitrogen anstenitic stainless steel were studied using the scanning electron microscopy, transmission electron microscopy, electron probe micro analysis and mechanical testing. The results show that, Cr2N is the primary precipitate in the tested stainless steels instead of Cr23C6. Cr2N nucleates at austenitic grain boundaries and grows towards inner grains with a lameUar morphology. By means of pre-precipitation of Cr2N at 800 ~C, the microstructure of the steels at solid solution state can be refined, thus improving the strength and plasticity. After the proposed treatment, the tensile strength, the proof strength and the elongation of the tested steel reach 881 MPa, 542 MPa and 54%, respectively.
基金Project(JB141405)supported by the Fundamental Research Funds for the Central Universities of China
文摘Alkali metal(Li, Na, K) doped ZnO powders were synthesized by solid-state reaction at different calcination temperatures and holding time. Effects of holding time and K sources on the infrared emissivity of ZnO were investigated. The structure and surface morphologies of samples were characterized by X-ray diffraction(XRD) and scanning electron microscopy(SEM). The UV-Vis absorption and infrared emissivities were investigated by a UV-Vis spectrophotometer and an infrared emissometer, respectively. XRD patterns confirm the wurtzite structure of the as prepared samples with single phase. Smooth grain surfaces are detected in all doped ZnO samples, while ZnO:Li and ZnO:Na present the aggregation of grains. The redshifts in the optical band-gap are observed in K-, Na-, and Li-doped ZnO with the values 3.150, 3.144, and 3.142 eV. Due to better crystalline quality, ZnO:K shows a lower emissivity than others. The emissivity of K-doped ZnO decreases to the minimum value(0.804), at 1200 °C and holding 2 h. Compared with KNO3 as K source, K2CO3 doped ZnO has lower emissivities.
基金Project(51205428) supported by the National Natural Science Foundation of ChinaProject(CDJRC10130011) supported by the Fundamental Research Funds for the Central Universities, ChinaProject(2010-0001-222) supported by NCRC (National Core Research Center) Program through the National Research Foundation of Korea funded by the Ministry of Education, Science and Technology,Korea
文摘Effect of holding time on microstructural developments and transformation of precipitates formed at the interface during transient liquid-phase bonding of a duplex stainless steel using a Ni-based amorphous insert alloy was studied. The experimental results reveal that the microstructure of the adjacent base metal varies clearly as a function of holding time. The migration of Cr and Ni elements and the → transformation seem to play relevant roles in this microstructure evolution. The scanning electron microscopy (SEM) and electron prob X-ray microanalysis (EPMA) results indicate the transformation of BN→BN and (N, Mo) boride→BN at the interface with the holding time of 60-1 800 s. N content changes with holding time increasing at locations at the interface might be a controlling factor contributing to this transformation.
基金Project(2008BAE63B00) supported by the National Key Technologies Research and Development Program of China
文摘Microarc oxidation （MAO） coatings were prepared on 2024 aluminum alloy in a Na2SiO3-KOH electrolyte with KNinO4 addition varying from 0 to 4 g/L. The microstructure and phases of the coatings were characterized by scanning electron microscopy （SEM） and X-ray diffractometry （XRD）, respectively. The corrosion resistance of MAO coatings was evaluated by electrochemical potentiodynamic polarization in 5% （mass fraction） NaCl solution. The results show that when KMnO4 is added into base electrolyte, the growth speed of oxide coatings is increased obviously. The main phase of oxide coatings is Al2O3, and the contents of MnO2 and MnEA104 phases are increased at the top of oxide coatings with increasing the concentration of KMnO4. The solute elements participate in forming the oxide coatings. When a proper concentration of KMnO4 （2.5 g/L） is added into the base solution, the micropores of the MAO coatings are small and compact, and the corrosion resistance of oxide coatings is increased largely.
基金Project(21176264)supported by the National Natural Science Foundation of ChinaProject(11JJ2010)supported by the Hunan Provincial Natural Science Foundation of China
文摘Poly （vinyl butyral） （PVB） hollow fiber membranes were fabricated via thermally induced phase separation （TIPS）. The effects of coagulation bath temperature （CBT） on the structure and performance of membranes were investigated in detail. The morphologies of the membranes were studied by scanning electron microscopy （SEM）, the performances of water permeability, rejection, breaking strength and elongation were measured, respectively. The results indicate that all the membranes have the asymmetric morphology and the thickness of the skin layer decreases and the pore size of the outer layer increases with the increase of CBT. The permeability of membranes prepared at air gap 1.0 cm and take-up speed 0.253 m/s increases from 1.047×10-7 to 5.909×10-7 m3/（m2·s-kPa） with the CBT increasing from 20 ℃ to 40℃, and sharply increases to 35.226×10 7 m3/（m2.s.kPa）once the CBT arrives at 50 ℃. While the carbonic ink rejections have no significant decrease, totally exceed 98%, but that of acid-maleic acid copolymer greatly decreases with the increase of CBT. Both the breaking strength and elongation decrease with the increase of CBT.
文摘Similar friction welded joints of AA-7005 aluminum rods were fabricated using different combinations of process parameters such as friction pressure(1.0, 1.5 and 2.0 MPa) and friction time(10, 15 and 20 s). Interfacial microstructure and formation of intermetallic compounds at the joint interface were evaluated via scanning electron microscopy(SEM) equipped with energy dispersive spectrum(EDS), and optical microscopy(OM). Microstructural observations reveal the formation of intermetallic phases during the welding process which cannot be extruded from the interface. Theses phases influence the tensile strength of the resultant joints. From the tensile characteristics viewpoint, the greatest tensile strength value of 365 MPa is obtained at 1.5 MPa and 15 s. Finally, the role of microstructural features on tensile strength of resultant joints is discussed.
基金Project(50705022) supported by the National Natural Science Foundation of ChinaProject supported by the Program for New Century Excellent Talents in University
文摘Oxygen-free copper and pre-metalized graphite were brazed using CuNiSnP braze alloy by high frequency induction heating method. Interracial microstructures and reaction phases were analyzed by scanning electron microscopy （SEM） and energy dispersive X-ray spectroscopy （EDS）. The strength and resistance of the joints were tested. It is found that when the brazing parameters are optimized, the structures of the joints are graphite/（Cu,Ni）/Ni（s.s）＋NixPy/Cu3P＋Cu（s.s） （including Sn）＋eutectic structures （Cu3P＋Ni3P＋Cu（s.s）/Cu （s.s）/Cu）. When the temperature increases to 750℃ or the holding time prolongs to 300 s, the eutectie structures disappear and the amount of Cu3P increases. The maximum shear strength of the joints is 5.2 MPa, which fracture at the interface of graphite and metallization. The resistance of the joints is no more than 5 mΩ.
基金Project(51371155)supported by the National Natural Science Foundation of ChinaProject(2014H0046)supported by the Key Science and Technology Project of Fujian Province,China+2 种基金Project(3502Z20143036)supported by the Scientific Research Fund of Xiamen,ChinaProject(JB13149)supported by the Education Department Science and Technology Project of Fujian Province,ChinaProject(2012D131)supported by the Natural Science Foundation Guidance Project of Fujian Province,China
文摘Molybdenum disilicide(MoSi_2) based composites with various contents of carbon nanotubes(CNTs) were fabricated by spark plasma sintering(SPS) in vacuum under a pressure of 25 MPa.The composites obtained under a sintering temperature of 1500 °C and time of 10 min exhibited optimum mechanical properties at room temperature in terms of fracture toughness and transverse rupture strength.MoSi_2 based composite with 6.0% CNTs(volume fraction) had the highest fracture toughness,transverse rupture strength and hardness,which were improved by about 25.7%,51.5% and 24.4% respectively,as compared with pure MoSi_2.A Mo_(4.8)Si_3C_(0.6) phase was detected in CNTs/MoSi_2 composites by both X-ray diffraction(XRD) method and microstructure analysis with scanning electron microscopy(SEM).It is believed that the fine grains and well dispersed small Mo_(4.8)Si_3C_(0.6) particles had led to a higher hardness and strength of CNTs/MoSi_2 composites because of their particle pullout,crack deflection and micro-bridging effects.
