The massive accumulation of flue gas desulfurization(FGD)gypsum produced in the wet limestone-gypsum flue gas desulfurization process not only encroaches on lands but also causes serious environmental pollution.The pr...The massive accumulation of flue gas desulfurization(FGD)gypsum produced in the wet limestone-gypsum flue gas desulfurization process not only encroaches on lands but also causes serious environmental pollution.The preparation ofα-hemihydrate gypsum(α-HH)is an important way to achieve high-value utilization of FGD gypsum.Although the glycerol-water solution approach can be used to produceα-HH from FGD gypsum under mild conditions,the transition is kinetically unfavorable in the mixed solution.Here,an easy pretreatment was used to activate FGD gypsum by calcination and hydration to readily complete the transition.The pretreatment deteriorated the crystallinity of FGD gypsum and caused it to form small irregular flaky crystals,which dramatically increased the specific surface area.Additionally,most of the organics adsorbed onto FGD gypsum surfaces were removed after pretreatment.The poor crystallinity,increased specific surface area,and elimination of organics adsorbed onto crystal surfaces effectively improved the conversion activity of FGD gypsum,thereby promoting dihydrate gypsum(DH)dissolution andα-HH nucleation.Overall,the phase transition of FGD gypsum toα-HH is facilitated.展开更多
The electrochemical treatment of wastewater containing chlorophenols （2-monochlorophenol, 4-monochlorophenol, 2,4-dichlorophenol, 2,4,6-trichlorophenol） was carried out experimentally with synthetic boron-d0ped diam...The electrochemical treatment of wastewater containing chlorophenols （2-monochlorophenol, 4-monochlorophenol, 2,4-dichlorophenol, 2,4,6-trichlorophenol） was carried out experimentally with synthetic boron-d0ped diamond （BDD） thin film electrodes. Current vs time curves under different cell voltages were measured. Removal rate of COD, instant current efficiency （ICE） and energy consumption were investigated under different current densities. The influence of supporting media is reported, which plays an important role in determining the global oxidation rate. The oxidative chloride is stronger than peroxodisulphate. The electrochemical characteristics of boron-doped diamond electrodes were investigated in comparison with active coating Ti substrate anode （ACT）. The experimental results show that BDD is markedly superior to ACT due to its different absorption properties.展开更多
The effects of pre-aging treatments on subsequent artificial aging response were investigated by means of transmission electron microscopy observations and hardness test in age hardened Al-3.95Cu-(1.32Mg)-0.52Mn-0.11 ...The effects of pre-aging treatments on subsequent artificial aging response were investigated by means of transmission electron microscopy observations and hardness test in age hardened Al-3.95Cu-(1.32Mg)-0.52Mn-0.11 Zr alloys. In Al-3.95Cu-0.52Mn-0.11 Zr alloy, when the pre-aging temperature is 25 °C, the pre-aging treatment has no evident effect on the peak hardness of subsequent artificial aging, while a positive effect(increase of peak hardness) appears when pre-aging temperature is50 °C. However, in Al-3.95Cu-1.32Mg-0.52Mn-0.11 Zr alloy, it is found that whether the pre-aging temperature is 25 °C or 50 °C,the peak artificial aging hardness is lower than that of T6 treated alloy, that is to say, pre-aging treatment has a negative effect on the peak hardness of subsequent artificial aging in the alloys.展开更多
Electrical steel sheets with 6.5%(mas fraction) Si with good shapes and superior magnetic inductions were successfully produced by a specially designed processing route including ingot casting, hot rolling and warm ro...Electrical steel sheets with 6.5%(mas fraction) Si with good shapes and superior magnetic inductions were successfully produced by a specially designed processing route including ingot casting, hot rolling and warm rolling both with interpass thermal treatment, and final annealing. The sheets were of 0.2 mm and 0.3 mm thick over 140 mm width. A detailed study of the microstructural and textural evolutions from the hot rolling to annealing was carried out by optical microscopy, X-ray diffraction and electron backscattered diffraction. The hot rolled sheet characterized by near-equiaxed grains was dominated by the mixture of <001>//ND fiber(λ-fiber), <110>//RD fiber(α-fiber) and <111>//ND fiber(γ-fiber) textures owing to the partial recrystallization and strain induced boundary migration(SIBM) during the hot rolling interpass thermal treatment. The static recovery and SIBM during the warm rolling interpass thermal treatment result in large and elongated warm rolling grains. The warm rolling texture is dominated by obvious λ, Goss and strong γ-fiber textures. The application of the interpass thermal treatment during hot and warm rolling significantly enhances the impact of SIBM during annealing, which is responsible for the formation of the moderate λ-fiber, some near-λ fiber texture components and the obviously weakened γ-fiber texture in the annealed sheet, leading to a higher magnetic induction compared to the commercially produced 6.5% Si steel by chemical vapor deposition(CVD).展开更多
基金Projects(51904104,51974117,51804114)supported by the National Natural Science Foundation of ChinaProjects(2018YFC1901601,2018YFC1901602,2018YFC1901605)supported by the National Key Scientific Research Project of China+1 种基金Project(2015CX005)supported by the Innovation Driven Plan of Central South University,ChinaProject(18B226)supported by the Excellent Youth Project of Hunan Education Department,China
文摘The massive accumulation of flue gas desulfurization(FGD)gypsum produced in the wet limestone-gypsum flue gas desulfurization process not only encroaches on lands but also causes serious environmental pollution.The preparation ofα-hemihydrate gypsum(α-HH)is an important way to achieve high-value utilization of FGD gypsum.Although the glycerol-water solution approach can be used to produceα-HH from FGD gypsum under mild conditions,the transition is kinetically unfavorable in the mixed solution.Here,an easy pretreatment was used to activate FGD gypsum by calcination and hydration to readily complete the transition.The pretreatment deteriorated the crystallinity of FGD gypsum and caused it to form small irregular flaky crystals,which dramatically increased the specific surface area.Additionally,most of the organics adsorbed onto FGD gypsum surfaces were removed after pretreatment.The poor crystallinity,increased specific surface area,and elimination of organics adsorbed onto crystal surfaces effectively improved the conversion activity of FGD gypsum,thereby promoting dihydrate gypsum(DH)dissolution andα-HH nucleation.Overall,the phase transition of FGD gypsum toα-HH is facilitated.
基金Project(20113282241450) supported by the Science and Technology Program from Ministry of Transport of China
文摘The electrochemical treatment of wastewater containing chlorophenols （2-monochlorophenol, 4-monochlorophenol, 2,4-dichlorophenol, 2,4,6-trichlorophenol） was carried out experimentally with synthetic boron-d0ped diamond （BDD） thin film electrodes. Current vs time curves under different cell voltages were measured. Removal rate of COD, instant current efficiency （ICE） and energy consumption were investigated under different current densities. The influence of supporting media is reported, which plays an important role in determining the global oxidation rate. The oxidative chloride is stronger than peroxodisulphate. The electrochemical characteristics of boron-doped diamond electrodes were investigated in comparison with active coating Ti substrate anode （ACT）. The experimental results show that BDD is markedly superior to ACT due to its different absorption properties.
基金Project(2006AA03Z517)supported by the National High-tech Research and Development Program of ChinaProject(CSUZC2013019)supported by Open Fund for the Precision Instruments of Central South University,China
文摘The effects of pre-aging treatments on subsequent artificial aging response were investigated by means of transmission electron microscopy observations and hardness test in age hardened Al-3.95Cu-(1.32Mg)-0.52Mn-0.11 Zr alloys. In Al-3.95Cu-0.52Mn-0.11 Zr alloy, when the pre-aging temperature is 25 °C, the pre-aging treatment has no evident effect on the peak hardness of subsequent artificial aging, while a positive effect(increase of peak hardness) appears when pre-aging temperature is50 °C. However, in Al-3.95Cu-1.32Mg-0.52Mn-0.11 Zr alloy, it is found that whether the pre-aging temperature is 25 °C or 50 °C,the peak artificial aging hardness is lower than that of T6 treated alloy, that is to say, pre-aging treatment has a negative effect on the peak hardness of subsequent artificial aging in the alloys.
基金Projects(51004035,51374002,50734001)supported by the National Natural Science Foundation of ChinaProject(2012BAE03B00)supported by the National Key Technology R&D Program,China+1 种基金Project(2012AA03A506)supported by the High-tech R&D Program,ChinaProject(N120407009)supported by the Fundamental Research Funds for the Central Universities,China
文摘Electrical steel sheets with 6.5%(mas fraction) Si with good shapes and superior magnetic inductions were successfully produced by a specially designed processing route including ingot casting, hot rolling and warm rolling both with interpass thermal treatment, and final annealing. The sheets were of 0.2 mm and 0.3 mm thick over 140 mm width. A detailed study of the microstructural and textural evolutions from the hot rolling to annealing was carried out by optical microscopy, X-ray diffraction and electron backscattered diffraction. The hot rolled sheet characterized by near-equiaxed grains was dominated by the mixture of <001>//ND fiber(λ-fiber), <110>//RD fiber(α-fiber) and <111>//ND fiber(γ-fiber) textures owing to the partial recrystallization and strain induced boundary migration(SIBM) during the hot rolling interpass thermal treatment. The static recovery and SIBM during the warm rolling interpass thermal treatment result in large and elongated warm rolling grains. The warm rolling texture is dominated by obvious λ, Goss and strong γ-fiber textures. The application of the interpass thermal treatment during hot and warm rolling significantly enhances the impact of SIBM during annealing, which is responsible for the formation of the moderate λ-fiber, some near-λ fiber texture components and the obviously weakened γ-fiber texture in the annealed sheet, leading to a higher magnetic induction compared to the commercially produced 6.5% Si steel by chemical vapor deposition(CVD).
