A three-dimensional finite element model was established for the milling of thin-walled parts. The physical model of the milling of the part was established using the AdvantEdge FEM software as the platform. The alumi...A three-dimensional finite element model was established for the milling of thin-walled parts. The physical model of the milling of the part was established using the AdvantEdge FEM software as the platform. The aluminum alloy impeller was designated as the object to be processed and the boundary conditions which met the actual machining were set. Through the solution, the physical quantities such as the three-way cutting force, the tool temperature, and the tool stress were obtained, and the calculation of the elastic deformation of the thin-walled blade of the free-form surface at the contact points between the tool and the workpiece was realized. The elastic deformation law of the thin-walled blade was then predicted. The results show that the maximum deviation between the predicted value and the actual measured machining value of the elastic deformation was 26.055 μm; the minimum deviation was 2.011 μm, with the average deviation being 10.154 μm. This shows that the prediction is in close agreement with the actual result.展开更多
For contact dominated numerical control(NC) bending process of tube, the effect of friction on bending deformation behaviors should be focused on to achieve precision bending forming. A three dimensional(3D) elastic-p...For contact dominated numerical control(NC) bending process of tube, the effect of friction on bending deformation behaviors should be focused on to achieve precision bending forming. A three dimensional(3D) elastic-plastic finite element(FE) model of NC bending process was established under ABAQUS/Explicit platform, and its reliability was validated by the experiment. Then, numerical study on bending deformation behaviors under different frictions between tube and various dies was explored from multiple aspects such as wrinkling, wall thickness change and cross section deformation. The results show that the large friction of wiper die-tube reduces the wrinkling wave ratio η and cross section deformation degree ΔD and increases the wall thinning degree Δt. The large friction of mandrel-tube causes large η, Δt and ΔD, and the onset of wrinkling near clamp die. The large friction of pressure die-tube reduces Δt and ΔD, and the friction on this interface has little effect on η. The large friction of bending die-tube reduces η and ΔD, and the friction on this interface has little effect on Δt. The reasonable friction coefficients on wiper die-tube, mandrel-tube, pressure die-tube and bending die-tube of 21-6-9(0Cr21Ni6Mn9N) stainless steel tube in NC bending are 0.05-0.15, 0.05-0.15, 0.25-0.35 and 0.25-0.35, respectively. The results can provide a guideline for applying the friction conditions to establish the robust bending environment for stable and precise bending deformation of tube bending.展开更多
To investigate the influence of bluff body shape on wall pressure distribution in a vortex flowmeter,experiments were conducted on a specially designed test section in a closed water rig at Reynolds numbers of 6.2...To investigate the influence of bluff body shape on wall pressure distribution in a vortex flowmeter,experiments were conducted on a specially designed test section in a closed water rig at Reynolds numbers of 6.2×10 4-9.3×10 4.The cross sections of the bluff bodies were semicircular,square,and triangular shaped,and there were totally 21 pressure tappings along the conduit to acquire the wall pressures.It is found that the variation trends of wall pressures are basically identical regardless of the bluff body shapes.The wall pressures begin to diverge from 0.3D(D is the inner diameter of the vortex flowmeter) in front of the bluff body due to the diversity in shape,and all reach the minimum values at 0.3D behind the bluff body.A discrepancy between the triangular or square cylinder and the semicircular cylinder in wall pressure change is observed at 0-0.1D behind the bluff body.It is also found that the wall pressures and irrecoverable pressure loss coefficients increase with flow rates,and the triangular cylinder causes the smallest irrecoverable pressure loss at a fixed flow rate.展开更多
基金Project(U1530138)supported by the National Natural Science Foundation of ChinaProject(A1-8903-17-0103)supported by the Natural Science Foundation of Shanghai Municipal Education Commission,China
文摘A three-dimensional finite element model was established for the milling of thin-walled parts. The physical model of the milling of the part was established using the AdvantEdge FEM software as the platform. The aluminum alloy impeller was designated as the object to be processed and the boundary conditions which met the actual machining were set. Through the solution, the physical quantities such as the three-way cutting force, the tool temperature, and the tool stress were obtained, and the calculation of the elastic deformation of the thin-walled blade of the free-form surface at the contact points between the tool and the workpiece was realized. The elastic deformation law of the thin-walled blade was then predicted. The results show that the maximum deviation between the predicted value and the actual measured machining value of the elastic deformation was 26.055 μm; the minimum deviation was 2.011 μm, with the average deviation being 10.154 μm. This shows that the prediction is in close agreement with the actual result.
基金Project(51164030)supported by the National Natural Science Foundation of China
文摘For contact dominated numerical control(NC) bending process of tube, the effect of friction on bending deformation behaviors should be focused on to achieve precision bending forming. A three dimensional(3D) elastic-plastic finite element(FE) model of NC bending process was established under ABAQUS/Explicit platform, and its reliability was validated by the experiment. Then, numerical study on bending deformation behaviors under different frictions between tube and various dies was explored from multiple aspects such as wrinkling, wall thickness change and cross section deformation. The results show that the large friction of wiper die-tube reduces the wrinkling wave ratio η and cross section deformation degree ΔD and increases the wall thinning degree Δt. The large friction of mandrel-tube causes large η, Δt and ΔD, and the onset of wrinkling near clamp die. The large friction of pressure die-tube reduces Δt and ΔD, and the friction on this interface has little effect on η. The large friction of bending die-tube reduces η and ΔD, and the friction on this interface has little effect on Δt. The reasonable friction coefficients on wiper die-tube, mandrel-tube, pressure die-tube and bending die-tube of 21-6-9(0Cr21Ni6Mn9N) stainless steel tube in NC bending are 0.05-0.15, 0.05-0.15, 0.25-0.35 and 0.25-0.35, respectively. The results can provide a guideline for applying the friction conditions to establish the robust bending environment for stable and precise bending deformation of tube bending.
基金Project(51006125) supported by the National Natural Science Foundation of China
文摘To investigate the influence of bluff body shape on wall pressure distribution in a vortex flowmeter,experiments were conducted on a specially designed test section in a closed water rig at Reynolds numbers of 6.2×10 4-9.3×10 4.The cross sections of the bluff bodies were semicircular,square,and triangular shaped,and there were totally 21 pressure tappings along the conduit to acquire the wall pressures.It is found that the variation trends of wall pressures are basically identical regardless of the bluff body shapes.The wall pressures begin to diverge from 0.3D(D is the inner diameter of the vortex flowmeter) in front of the bluff body due to the diversity in shape,and all reach the minimum values at 0.3D behind the bluff body.A discrepancy between the triangular or square cylinder and the semicircular cylinder in wall pressure change is observed at 0-0.1D behind the bluff body.It is also found that the wall pressures and irrecoverable pressure loss coefficients increase with flow rates,and the triangular cylinder causes the smallest irrecoverable pressure loss at a fixed flow rate.
