The precipitation behaviors of an A1-Cu-Li-Mn-Zr alloy at different ageing temperatures （120, 160 and 200 ~C） were investigated using Vickers hardness measurements and transmission electron microscopy （TEM） charac...The precipitation behaviors of an A1-Cu-Li-Mn-Zr alloy at different ageing temperatures （120, 160 and 200 ~C） were investigated using Vickers hardness measurements and transmission electron microscopy （TEM） characterization. Age hardening curves show an increase in precipitation kinetics with increasing ageing temperature. The results of TEM show that for the samples peak aged at 120 ~C, the amount of g＇ （A13Li）, GP zones/0＇ （A12Cu） and Z （A15Cu6Li2） phases is obviously higher than that of T1 （A12CuLi） precipitates; while the samples peak aged at 160 and 200 ~C are usually dominated by T1 phase with a minor fraction of GP zones/0＇ and g＇, and the Z phase almost does not form. In addition, quantitative analysis on the T1 platelets demonstrates that the samples peak aged at 200 ~C have larger plate diameter and smaller area fraction of T1, as compared to the samples peak aged at 160 ~C. Correspondingly, the possible reasons for such phenomena are discussed.展开更多
The effect of moisture content upon compressive mechanical behavior of concrete under impact loading was studied. The axial rapid compressive loading tests of over 50 specimens with five different saturations were exe...The effect of moisture content upon compressive mechanical behavior of concrete under impact loading was studied. The axial rapid compressive loading tests of over 50 specimens with five different saturations were executed. The technique "split Hopkinson pressure bar"(SHPB) was used. The impact velocity was 10 m/s with corresponding strain rate of 50 s-1. The compressive behavior of materials was measured in terms of stress-strain curves, dynamic compressive strength, dynamic increase factor(DIF) and critical strain at a maximum stress. The data obtained from test indicate that both ascending and descending portions of stress-stain curves are affected by moisture content. However, the effect is noted to be more significant in ascending portion of the stress-strain curves. Dynamic compressive strength is higher at lower moisture content and weaker at higher moisture content.Furthermore, under nearly saturated condition, an increase in compressive strength can be found. The effect of moisture content on the average DIF of concrete is not significant. The critical compressive strain of concrete does not change with moisture content.展开更多
The accurate measurement of kinematic parameters in satellite separation tests has great significance in evaluating separation performance. A novel study is made on the measuring accuracy of monocular and binocular, w...The accurate measurement of kinematic parameters in satellite separation tests has great significance in evaluating separation performance. A novel study is made on the measuring accuracy of monocular and binocular, which are the two main vision measurement methods used for kinematic parameters. As satellite separation process is transient and high-dynamic, it will bring more extraction errors to the binocular. Based on the design approach of intersection measure and variance ratio, the monocular method reflects higher precision, simpler structure and easier calibration for level satellite separation. In ground separation tests, a high-speed monocular system is developed to gain and analyze twelve kinematic parameters of a small satellite. Research shows that this monocular method can be widely applied for its high precision, with position accuracy of 0.5 mm, speed accuracy of 5 mm/s, and angular velocity accuracy of 1 (°)/s.展开更多
The drawn copper wires have been analyzed by differential scanning calorimeter(DSC) and a new method, which uses DSC measurements to determine the Johnson-Mehl-Avrami-Kolmogorov(JMAK) exponent via introducing Arrheniu...The drawn copper wires have been analyzed by differential scanning calorimeter(DSC) and a new method, which uses DSC measurements to determine the Johnson-Mehl-Avrami-Kolmogorov(JMAK) exponent via introducing Arrhenius behavior and modifying the baseline of DSC curves, has been proposed. The results show that JMAK exponent and recrystallization activation energy of the drawn copper wires with a strain of 2.77 are about 2.39 and 125 k J/mol, respectively. The line linking the tangency points of DSC curve hypotenuse can be used as the baseline when calculating recrystallization fraction. The JMAK exponent obtained by the DSC method is in a good agreement with that obtained by microhardness measurements. Compared to traditional methods to measure the exponent, the proposed method is faster and less labor intensive.展开更多
基金Project（2016YFB0300901） supported by the National Key R＆D Program of China Project（51421001） supported by the National Natural Science Foundation of China Project（2018CDJDCL0019） supported by the Fundamental Research Funds for the Central Universities, China
文摘The precipitation behaviors of an A1-Cu-Li-Mn-Zr alloy at different ageing temperatures （120, 160 and 200 ~C） were investigated using Vickers hardness measurements and transmission electron microscopy （TEM） characterization. Age hardening curves show an increase in precipitation kinetics with increasing ageing temperature. The results of TEM show that for the samples peak aged at 120 ~C, the amount of g＇ （A13Li）, GP zones/0＇ （A12Cu） and Z （A15Cu6Li2） phases is obviously higher than that of T1 （A12CuLi） precipitates; while the samples peak aged at 160 and 200 ~C are usually dominated by T1 phase with a minor fraction of GP zones/0＇ and g＇, and the Z phase almost does not form. In addition, quantitative analysis on the T1 platelets demonstrates that the samples peak aged at 200 ~C have larger plate diameter and smaller area fraction of T1, as compared to the samples peak aged at 160 ~C. Correspondingly, the possible reasons for such phenomena are discussed.
基金Project(50979032)supported by the National Natural Science Foundation of China
文摘The effect of moisture content upon compressive mechanical behavior of concrete under impact loading was studied. The axial rapid compressive loading tests of over 50 specimens with five different saturations were executed. The technique "split Hopkinson pressure bar"(SHPB) was used. The impact velocity was 10 m/s with corresponding strain rate of 50 s-1. The compressive behavior of materials was measured in terms of stress-strain curves, dynamic compressive strength, dynamic increase factor(DIF) and critical strain at a maximum stress. The data obtained from test indicate that both ascending and descending portions of stress-stain curves are affected by moisture content. However, the effect is noted to be more significant in ascending portion of the stress-strain curves. Dynamic compressive strength is higher at lower moisture content and weaker at higher moisture content.Furthermore, under nearly saturated condition, an increase in compressive strength can be found. The effect of moisture content on the average DIF of concrete is not significant. The critical compressive strain of concrete does not change with moisture content.
基金Project(50975280)supported by the National Natural Science Foundation of ChinaProject(NCET-08-0149)supported by Program for New Century Excellent Talents in Universities of China
文摘The accurate measurement of kinematic parameters in satellite separation tests has great significance in evaluating separation performance. A novel study is made on the measuring accuracy of monocular and binocular, which are the two main vision measurement methods used for kinematic parameters. As satellite separation process is transient and high-dynamic, it will bring more extraction errors to the binocular. Based on the design approach of intersection measure and variance ratio, the monocular method reflects higher precision, simpler structure and easier calibration for level satellite separation. In ground separation tests, a high-speed monocular system is developed to gain and analyze twelve kinematic parameters of a small satellite. Research shows that this monocular method can be widely applied for its high precision, with position accuracy of 0.5 mm, speed accuracy of 5 mm/s, and angular velocity accuracy of 1 (°)/s.
基金Projects(51171135,51371132,51471123) supported by the National Natural Science Foundation of ChinaProjects(2012K07-08,2013KJXX-61) supported by Key Science and Technology Program of Shaanxi Province,ChinaProject(2013JC14) supported by the Education Department Foundation of Shaanxi Province,China
文摘The drawn copper wires have been analyzed by differential scanning calorimeter(DSC) and a new method, which uses DSC measurements to determine the Johnson-Mehl-Avrami-Kolmogorov(JMAK) exponent via introducing Arrhenius behavior and modifying the baseline of DSC curves, has been proposed. The results show that JMAK exponent and recrystallization activation energy of the drawn copper wires with a strain of 2.77 are about 2.39 and 125 k J/mol, respectively. The line linking the tangency points of DSC curve hypotenuse can be used as the baseline when calculating recrystallization fraction. The JMAK exponent obtained by the DSC method is in a good agreement with that obtained by microhardness measurements. Compared to traditional methods to measure the exponent, the proposed method is faster and less labor intensive.
