期刊文献+
共找到3篇文章
< 1 >
每页显示 20 50 100
节理岩体抗剪强度参数的实验分析 被引量:13
1
作者 周应华 周德培 +1 位作者 杨涛 封志军 《西南交通大学学报》 EI CSCD 北大核心 2005年第1期73-76,共4页
对红层软岩的大量实验表明,剪切与三轴压缩实验测得的抗剪强度参数值不一致,而且内摩擦角从完整岩石剪切实验、三轴压缩实验到结构面剪切实验呈现出由大到小的规律.基于上述实验结果,分别从岩石强度理论和实验方法的角度分析了3种实验... 对红层软岩的大量实验表明,剪切与三轴压缩实验测得的抗剪强度参数值不一致,而且内摩擦角从完整岩石剪切实验、三轴压缩实验到结构面剪切实验呈现出由大到小的规律.基于上述实验结果,分别从岩石强度理论和实验方法的角度分析了3种实验所得参数不一致的原因,导出了三轴压缩实验得到的岩体抗剪强度参数与结构面抗剪强度参数之间的关系式,并提出了岩体抗剪强度参数的选取原则. 展开更多
关键词 红层软岩 抗剪强度参数 莫尔-库仑准则 三轴实验 剪切实验-
在线阅读 下载PDF
SUS304不锈钢板点焊接头超声成像及力学性能 被引量:8
2
作者 张龙 曾凯 +3 位作者 何晓聪 邢保英 孙鑫宇 胡伟 《材料工程》 EI CAS CSCD 北大核心 2016年第4期26-31,共6页
利用超声波水浸聚焦入射法,对1mm厚的SUS304奥氏体不锈钢板点焊接头进行超声C扫描成像检测,研究不同焊接工艺参数下接头的C扫描图像特征,检测分析点焊的熔核直径,并对点焊接头进行拉伸-剪切实验。结果表明:超声波水浸聚焦C扫描成... 利用超声波水浸聚焦入射法,对1mm厚的SUS304奥氏体不锈钢板点焊接头进行超声C扫描成像检测,研究不同焊接工艺参数下接头的C扫描图像特征,检测分析点焊的熔核直径,并对点焊接头进行拉伸-剪切实验。结果表明:超声波水浸聚焦C扫描成像法能够有效检测点焊熔核直径,为4.76~5.25mm,比金相实测值大2.6%~5.3%;随着焊接电流的增加(4-8kA),接头的失效载荷均值从7116.8N增加到9707.1N,能量吸收均值从66.3J增加到196J,同时反映在C扫描图像上的熔核直径也从4.76mm增加到5.11mm;当焊接电流增加至9kA时,接头的失效载荷均值下降至6799.5N,能量吸收均值下降至41.3J,此时在C扫描图像上反映出飞溅、焊穿等典型的焊接缺陷。 展开更多
关键词 不锈钢点焊 超声波C扫描 拉伸-剪切实验 熔核直径 能量吸收
在线阅读 下载PDF
Unified analytical stressstrain curve for quasibrittle geomaterial in uniaxial tension, direct shear and uniaxial compression 被引量:5
3
作者 王学滨 《Journal of Central South University of Technology》 EI 2006年第1期99-104,共6页
Considering strain localization in the form of a narrow band initiated just at peak stress, three analytical expressions for stressstrain curves of quasibrittle geomaterial (such as rock and concrete) in uniaxial tens... Considering strain localization in the form of a narrow band initiated just at peak stress, three analytical expressions for stressstrain curves of quasibrittle geomaterial (such as rock and concrete) in uniaxial tension, direct shear and uniaxial compression were presented, respectively. The three derived stressstrain curves were generalized as a unified formula. Beyond the onset of strain localization, a linear strain-softening constitutive relation for localized band was assigned. The size of the band was controlled by internal or characteristic length according to gradient-dependent plasticity. Elastic strain within the entire specimen was assumed to be uniform and decreased with the increase of plastic strain in localized band. Total strain of the specimen was decomposed into elastic and plastic parts. Plastic strain of the specimen was the average value of plastic strains in localized band over the entire specimen. For different heights, the predicted softening branches of the relative stressstrain curves in uniaxial compression are consistent with the previously experimental results for normal concrete specimens. The present expressions for the post-peak stressdeformation curves in uniaxial tension and direct shear agree with the previously numerical results based on gradient-dependent plasticity. 展开更多
关键词 stress- strain curve uniaxial tension uniaxial compression direct shear shear band ROCK CONCRETE
在线阅读 下载PDF
上一页 1 下一页 到第
使用帮助 返回顶部