期刊文献+
共找到4篇文章
< 1 >
每页显示 20 50 100
残余奥氏体对300M超高强度钢冲击疲劳性能的影响 被引量:6
1
作者 朱子新 杜则裕 胡光立 《天津大学学报(自然科学与工程技术版)》 EI CAS CSCD 北大核心 2001年第3期379-382,共4页
研究了 30 0 M超高强度钢油淬和 2 70℃等温淬火组织中残余奥氏体 (AR)对冲击疲劳性能的影响 .结果表明 ,残余奥氏体量越多 ,冲击疲劳裂纹起始寿命 Ni 越低 ,裂纹扩展速率 da/ d N越快 .AR作为软相 ,使板条间易于相对滑移 ,产生微裂纹 ... 研究了 30 0 M超高强度钢油淬和 2 70℃等温淬火组织中残余奥氏体 (AR)对冲击疲劳性能的影响 .结果表明 ,残余奥氏体量越多 ,冲击疲劳裂纹起始寿命 Ni 越低 ,裂纹扩展速率 da/ d N越快 .AR作为软相 ,使板条间易于相对滑移 ,产生微裂纹 .AR对 da/ d N影响的主要机制是裂纹尖端塑性区内的应变诱发马氏体相变 . 展开更多
关键词 残余奥氏体 超高强度钢 冲击疲劳性能 裂纹扩展 淬火组织 马氏体相变
在线阅读 下载PDF
新型贝氏体钢与30CrNi4Mo钢力学性能和冲击疲劳性能的对比 被引量:2
2
作者 刘志学 程巨强 王元辉 《机械工程材料》 CAS CSCD 北大核心 2010年第2期30-34,共5页
为了用新型贝氏体钢替代30CrNi4 Mo钢,研究了两种钢在不同热处理后的显微组织、力学性能和多次冲击疲劳性能。结果表明:30CrNi4 Mo钢经奥氏体化后空冷和油冷+低温回火处理均具有高的强度和良好的冲击韧度;油冷后随回火温度的提高,组织... 为了用新型贝氏体钢替代30CrNi4 Mo钢,研究了两种钢在不同热处理后的显微组织、力学性能和多次冲击疲劳性能。结果表明:30CrNi4 Mo钢经奥氏体化后空冷和油冷+低温回火处理均具有高的强度和良好的冲击韧度;油冷后随回火温度的提高,组织由回火马氏体+残余奥氏体转变为索氏体,油冷+高温回火后具有良好的强韧性配合,且冲击疲劳总寿命高于空冷和油冷+低温回火的;新型贝氏体钢在水冷、油冷和空冷+低温回火后均具有良好的强韧性配合,空冷+低温回火的冲击疲劳寿命高于水冷、油冷+低温回火的;空冷+低温回火状态下新型贝氏体钢多冲疲劳寿命较高,可替代30CrNi4 Mo钢用作抗冲击载荷材料。 展开更多
关键词 30CrNi4Mo钢 新型贝氏体钢 冲击疲劳性能
在线阅读 下载PDF
物探冲击器活塞材料(T8A钢)的试验研究
3
作者 黄志强 李琴 +3 位作者 刘德明 李国忠 刘少彬 赵国辉 《石油机械》 北大核心 2003年第11期3-4,17,共3页
对物探冲击器活塞材料 (T8A钢 )的热处理工艺和抗冲击疲劳性能的试验研究结果表明 ,最佳热处理工序和工艺为调质处理预热淬火 (76 0℃× 2min)回火 (2 0 0℃× 1 5h) ;在这种工艺下 ,淬硬层深度为 2 5~ 3 2mm ,组织为... 对物探冲击器活塞材料 (T8A钢 )的热处理工艺和抗冲击疲劳性能的试验研究结果表明 ,最佳热处理工序和工艺为调质处理预热淬火 (76 0℃× 2min)回火 (2 0 0℃× 1 5h) ;在这种工艺下 ,淬硬层深度为 2 5~ 3 2mm ,组织为回火马氏体 +细粒状碳化物 ,心部组织为屈氏体 +细粒状碳化物 ,这种组织既保证了表层的高硬度 ,又具有良好的综合力学性能 ,抗疲劳性能试验中多次冲击下凹值最小 ,麻点出现数目最少 ,有较好的多次冲击疲劳抗力。研制活塞实物的现场试验累计工作寿命达 4 0 0h ,抗冲击疲劳寿命大大提高。 展开更多
关键词 物探冲击 活塞材料 T8A钢 试验 热处理工艺 冲击疲劳性能 地质勘探
在线阅读 下载PDF
Impact performance of a floating slab with a longitudinal connection track under fatigue loading
4
作者 LI Pei-cheng ZENG Zhi-ping +3 位作者 WANG Wei-dong LI Ping YE Meng-xuan LI Qiu-yi 《Journal of Central South University》 2025年第2期678-690,共13页
In order to accommodate higher speeds,heavier axle weights,and vibration damping criteria,a new floating slab structure was proposed.The new type of floating slab track structure was composed of three prefabricated fl... In order to accommodate higher speeds,heavier axle weights,and vibration damping criteria,a new floating slab structure was proposed.The new type of floating slab track structure was composed of three prefabricated floating slabs longitudinally interconnected with magnesium ammonium phosphate concrete(MPC).This study investigated the dynamic performance of the structure.We constructd a full-scale indoor experimental model to scrutinize the disparities in the impact performance between a longitudinally connected floating slab track and its longitudinally disconnected counterpart.Additionally,a long-term fatigue experiment was conducted to assess the impact performance of longitudinally connected floating slab tracks under fatigue loading.The findings are described in the following.1)The new structure effectively suppresses ground vibrations,exhibiting a well-balanced energy distribution profile.However,the imposition of fatigue loading leads to a reduction in the damping performance of the steel spring damping system,thereby reducing its capacity to attenuate structural vibrations and leading to an increase in ground vibration energy;2)After 107 loading cycles,the attenuation rate of the vibration acceleration for the MPC increases by 171.9%.Conversely,at the corresponding disconnected location,the attenuation rate of ground vibration acceleration decreases by 65.6%.In conclusion,longitudinally connected floating slab tracks exhibit superior vibration reduction performance.While the vibration reduction performance of longitudinally connected floating slab tracks may diminish to some extent during long-term service,these tracks continue to meet specific vibration reduction requirements. 展开更多
关键词 longitudinally connected floating slab track full-scale experimental model fatigue experiment drop hammer in impact dynamic response
在线阅读 下载PDF
上一页 1 下一页 到第
使用帮助 返回顶部