Mesoporous carbon supports mitigate platinum(Pt)sulfonic poisoning through nanopore-confined Pt deposition,yet their morphological impacts on oxygen transport remain unclear.This study integrates carbon support morpho...Mesoporous carbon supports mitigate platinum(Pt)sulfonic poisoning through nanopore-confined Pt deposition,yet their morphological impacts on oxygen transport remain unclear.This study integrates carbon support morphology simulation with an enhanced agglomerate model to establish a mathematical framework elucidating pore evolution,Pt utilization,and oxygen transport in catalyst layers.Results demonstrate dominant local mass transport resistance governed by three factors:(1)active site density dictating oxygen flux;(2)ionomer film thickness defining shortest transport path;(3)ionomer-to-Pt surface area ratio modulating practical pathway length.At low ionomer-to-carbon(I/C)ratios,limited active sites elevate resistance(Factor 1 dominant).Higher I/C ratios improve the ionomer coverage but eventually thicken ionomer films,degrading transport(Factors 2–3 dominant).The results indicate that larger carbon particles result in a net increase in local transport resistance by reducing external surface area and increasing ionomer thickness.As the proportion of Pt situated in nanopores or the Pt mass fraction increases,elevated Pt density inside the nanopores exacerbates pore blockage.This leads to the increased transport resistance by reducing active sites,and increasing ionomer thickness and surface area.Lower Pt loading linearly intensifies oxygen flux resistance.The model underscores the necessity to optimize support morphology,Pt distribution,and ionomer content to prevent pore blockage while balancing catalytic activity and transport efficiency.These insights provide a systematic approach for designing high-performance mesoporous carbon catalysts.展开更多
采用Na AlO2和HCl两步法对ZSM-5分子筛进行改性,运用XRD、SEM、NH3-TPD、N2吸附-脱附、ICP-OES、TG等方法对改性前后的分子筛进行表征。结果表明:经Na Al O2改性后的ZSM-5分子筛中引入了介孔,且分子筛的晶型、酸性、微孔体积等保持较好...采用Na AlO2和HCl两步法对ZSM-5分子筛进行改性,运用XRD、SEM、NH3-TPD、N2吸附-脱附、ICP-OES、TG等方法对改性前后的分子筛进行表征。结果表明:经Na Al O2改性后的ZSM-5分子筛中引入了介孔,且分子筛的晶型、酸性、微孔体积等保持较好,并具有较高的固相收率;酸洗前通过中间焙烧有利于消除孔道覆盖和恢复酸性。将改性后的分子筛应用于甲醇芳构化反应中,在温度400℃、压力0.15 MPa、质量空速1.9h-1的反应条件下,经0.45 mol/L Na Al O2改性的分子筛反应效果最优,产物芳烃收率可达41.9%,BTX收率达32.7%;与原粉分子筛相比,产物芳烃收率提高了3.8百分点,BTX收率提高了4.4百分点;同时,其反应稳定性可达30 h,较原粉延长了1倍多。展开更多
SnO_(2)is used as electrode material with excellent properties,but it has some disadvantages such as slow reaction kinetics,low inherent conductivity and complex preparation process.Here,SnO_(2)@carbon nanotubes(SnO_(...SnO_(2)is used as electrode material with excellent properties,but it has some disadvantages such as slow reaction kinetics,low inherent conductivity and complex preparation process.Here,SnO_(2)@carbon nanotubes(SnO_(2)@CNTs)is synthesized through an efficient method of one-pot alternating current electrochemical dispersion.By using heat treatment at 400℃,the SnO_(2)@CNTs-400 composite material with abundant mesoporous structure is obtained,while the crystal particles are grown,and a strong bonding effect is formed with CNTs via powerful Sn-O-C bond.Benefiting from the introduction of high electrical conductivity CNTs and outstanding structural characteristics,as prepared composite material(SnO_(2)@CNTs-400)exhibit enhanced diffusion dynamics,lithium-ion transmission rate and structural steadiness.The specific capacity of SnO_(2)@CNTs and SnO_(2)@CNTs-400 as anodes for lithium-ion batteries can reach 690.2 mA·h/g and 836.5 mA·h/g,respectively,after 100 cycles at 0.5 A/g.The abundant chemical bonds and porous structure can be formed in composite via alternating current synthesis method,which takes significant in improving electrochemical properties.展开更多
The backward-facing step is a critical problem existing in many engineering and industrial applications.In this study,a semi-porous baffle(the root of the baffle is a porous medium and the tip is solid) is placed behi...The backward-facing step is a critical problem existing in many engineering and industrial applications.In this study,a semi-porous baffle(the root of the baffle is a porous medium and the tip is solid) is placed behind the step.The effects of the length of the porous part,and the baffle location on the energy transfer and pressure drop are studied in different Reynolds numbers(Re=100,200,300,400,500).The effect of the Darcy number of the porous medium on the aforementioned parameters is also investigated.Both the local maximum and average relative Nusselt numbers(divided by the Nusselt of the base case with no baffle at the same Reynolds) and relative pressure drop(calculated as the relative Nusselt number) are reported.The results show that by adoption of the proper length of the porous medium,the average relative and maximum local Nusselt numbers could be enhanced by 20% and 90%,respectively.Low permeable porous media give better energy transfer.For example,porous media with Da=10^(-5) give 30% better maximum local Nusselt number and about 7% higher average Nusselt number with respect to the same case with Da=10^(-2).展开更多
Miniaturization of electronic equipment has forced researchers to devise more effective methods for dissipating the generated heat in these devices.In this study,two methods,including porous media inserting and adding...Miniaturization of electronic equipment has forced researchers to devise more effective methods for dissipating the generated heat in these devices.In this study,two methods,including porous media inserting and adding nanoparticles to the base fluid,are used to improve heat transfer in an annulus heated on both walls.To study porous media insert,porous ribs are used on the outer and inner walls independently.The results show that when porous ribs are placed on the outer wall,although the heat transfer enhances,the pressure drop increment is so considerable that performance number (the ratio of heat transfer enhancement pressure increment,PN) is less than unity for all porous rib heights and porous media permeabilities that are studied.On the other hand,the PN of cases where porous ribs were placed on the inner wall depends on the Darcy number (Da).For example,for ribs with Da=0.1 and Da=0.0001,the maximum performance number,PN=4,occurs at the porous ribs height to hydraulic diameter ratios H/Dh=1 and H/Dh=0.25.Under these conditions,heat transfer is enhanced by two orders of magnitude.It is found that adding 5% nanoparticles to the base fluid in the two aforementioned cases improves the Nusselt number and PN by 10%–40%.展开更多
The pore structure images of ore particles located at different heights of leaching column were scanned with X-ray computerized tomography (CT) scanner, the porosity and pore size distribution were calculated and the ...The pore structure images of ore particles located at different heights of leaching column were scanned with X-ray computerized tomography (CT) scanner, the porosity and pore size distribution were calculated and the geometrical shape and connectivity of pores were analyzed based on image process method, and the three dimensional reconstruction of pore structure images was realized. The results show that the porosity of ore particles bed in leaching column is 42.92%, 41.72%, 39.34% at top, middle and bottom zone, respectively. Obviously it has spatial variability and decreases appreciably along the height of the column. The overall average porosity obtained by image processing is 41.33% while the porosity gotten from general measurement method in laboratory is 42.77% showing the results of both methods are consistent well. The pore structure of ore granular media is characterized as a dynamical space network composed of interconnected pore bodies and pore throats. The ratio of throats with equivalent diameter less than 1.91 mm to the total pores is 29.31%, and that of the large pores with equivalent diameter more than 5.73 mm is 2.90%.展开更多
The present article deals with thermally stratified stagnation-point flow saturated in porous medium on surface of variable thickness along with more convincing and reliable surface condition termed as melting heat tr...The present article deals with thermally stratified stagnation-point flow saturated in porous medium on surface of variable thickness along with more convincing and reliable surface condition termed as melting heat transfer.Homogeneous–heterogeneous reaction and radiative effects have been further taken into account to reconnoiterproperties of heat transfer.Melting heat transfer and phenomenon of homogeneous–heterogeneous reaction have engrossed widespread utilization in purification of metals,welding process,electroslag melting,biochemical systems,catalysis and several industrial developments.Suitable transformations are utilized to attain a scheme of ordinary differential equations possessing exceedingly nonlinear nature.Homotopic process is employed to develop convergent solutions of the resulting problem.Discussion regarding velocity,thermal field and concentration distribution for several involved parameters is pivotal part.Graphical behaviors of skin friction coefficient and Nusselt number are also portrayed.Concentration of the reactants is found to depreciate as a result of strength of both heterogeneous and homogeneous reaction parameters.With existence of melting phenomenon,declining attitude of fluid temperature is observed for higher radiation parameter.展开更多
基金supported by the Program of Ministry of Science and Technology of China(No.2023YFB2504200)support of Shanghai Rising-Star Program(Grant No.24QB2703200)the Major Science and Technology Projects of Yunnan Province(No.202302AH360001).
文摘Mesoporous carbon supports mitigate platinum(Pt)sulfonic poisoning through nanopore-confined Pt deposition,yet their morphological impacts on oxygen transport remain unclear.This study integrates carbon support morphology simulation with an enhanced agglomerate model to establish a mathematical framework elucidating pore evolution,Pt utilization,and oxygen transport in catalyst layers.Results demonstrate dominant local mass transport resistance governed by three factors:(1)active site density dictating oxygen flux;(2)ionomer film thickness defining shortest transport path;(3)ionomer-to-Pt surface area ratio modulating practical pathway length.At low ionomer-to-carbon(I/C)ratios,limited active sites elevate resistance(Factor 1 dominant).Higher I/C ratios improve the ionomer coverage but eventually thicken ionomer films,degrading transport(Factors 2–3 dominant).The results indicate that larger carbon particles result in a net increase in local transport resistance by reducing external surface area and increasing ionomer thickness.As the proportion of Pt situated in nanopores or the Pt mass fraction increases,elevated Pt density inside the nanopores exacerbates pore blockage.This leads to the increased transport resistance by reducing active sites,and increasing ionomer thickness and surface area.Lower Pt loading linearly intensifies oxygen flux resistance.The model underscores the necessity to optimize support morphology,Pt distribution,and ionomer content to prevent pore blockage while balancing catalytic activity and transport efficiency.These insights provide a systematic approach for designing high-performance mesoporous carbon catalysts.
文摘采用Na AlO2和HCl两步法对ZSM-5分子筛进行改性,运用XRD、SEM、NH3-TPD、N2吸附-脱附、ICP-OES、TG等方法对改性前后的分子筛进行表征。结果表明:经Na Al O2改性后的ZSM-5分子筛中引入了介孔,且分子筛的晶型、酸性、微孔体积等保持较好,并具有较高的固相收率;酸洗前通过中间焙烧有利于消除孔道覆盖和恢复酸性。将改性后的分子筛应用于甲醇芳构化反应中,在温度400℃、压力0.15 MPa、质量空速1.9h-1的反应条件下,经0.45 mol/L Na Al O2改性的分子筛反应效果最优,产物芳烃收率可达41.9%,BTX收率达32.7%;与原粉分子筛相比,产物芳烃收率提高了3.8百分点,BTX收率提高了4.4百分点;同时,其反应稳定性可达30 h,较原粉延长了1倍多。
基金Project(2023JЛ10041)supported by the Distinguished Young Scholar Fund Project of Hunan Province Natural Science Foundation,ChinaProject(22A0114)supported by the Hunan Provincial Education Office Foundation of China+2 种基金Projects(GX-ZD20211004,GX-ZD20221007)supported by the Science and Technology Program of Xiangtan,ChinaProject(R24-5979269037)supported by the RSC Research Fund Grout,EnglandProject(S202310530037X)supported by the National College Students Innovative Experimental Program Funding Project,China。
文摘SnO_(2)is used as electrode material with excellent properties,but it has some disadvantages such as slow reaction kinetics,low inherent conductivity and complex preparation process.Here,SnO_(2)@carbon nanotubes(SnO_(2)@CNTs)is synthesized through an efficient method of one-pot alternating current electrochemical dispersion.By using heat treatment at 400℃,the SnO_(2)@CNTs-400 composite material with abundant mesoporous structure is obtained,while the crystal particles are grown,and a strong bonding effect is formed with CNTs via powerful Sn-O-C bond.Benefiting from the introduction of high electrical conductivity CNTs and outstanding structural characteristics,as prepared composite material(SnO_(2)@CNTs-400)exhibit enhanced diffusion dynamics,lithium-ion transmission rate and structural steadiness.The specific capacity of SnO_(2)@CNTs and SnO_(2)@CNTs-400 as anodes for lithium-ion batteries can reach 690.2 mA·h/g and 836.5 mA·h/g,respectively,after 100 cycles at 0.5 A/g.The abundant chemical bonds and porous structure can be formed in composite via alternating current synthesis method,which takes significant in improving electrochemical properties.
文摘The backward-facing step is a critical problem existing in many engineering and industrial applications.In this study,a semi-porous baffle(the root of the baffle is a porous medium and the tip is solid) is placed behind the step.The effects of the length of the porous part,and the baffle location on the energy transfer and pressure drop are studied in different Reynolds numbers(Re=100,200,300,400,500).The effect of the Darcy number of the porous medium on the aforementioned parameters is also investigated.Both the local maximum and average relative Nusselt numbers(divided by the Nusselt of the base case with no baffle at the same Reynolds) and relative pressure drop(calculated as the relative Nusselt number) are reported.The results show that by adoption of the proper length of the porous medium,the average relative and maximum local Nusselt numbers could be enhanced by 20% and 90%,respectively.Low permeable porous media give better energy transfer.For example,porous media with Da=10^(-5) give 30% better maximum local Nusselt number and about 7% higher average Nusselt number with respect to the same case with Da=10^(-2).
文摘Miniaturization of electronic equipment has forced researchers to devise more effective methods for dissipating the generated heat in these devices.In this study,two methods,including porous media inserting and adding nanoparticles to the base fluid,are used to improve heat transfer in an annulus heated on both walls.To study porous media insert,porous ribs are used on the outer and inner walls independently.The results show that when porous ribs are placed on the outer wall,although the heat transfer enhances,the pressure drop increment is so considerable that performance number (the ratio of heat transfer enhancement pressure increment,PN) is less than unity for all porous rib heights and porous media permeabilities that are studied.On the other hand,the PN of cases where porous ribs were placed on the inner wall depends on the Darcy number (Da).For example,for ribs with Da=0.1 and Da=0.0001,the maximum performance number,PN=4,occurs at the porous ribs height to hydraulic diameter ratios H/Dh=1 and H/Dh=0.25.Under these conditions,heat transfer is enhanced by two orders of magnitude.It is found that adding 5% nanoparticles to the base fluid in the two aforementioned cases improves the Nusselt number and PN by 10%–40%.
基金Project(2004CB619205) supported by the National Key Fundamental Research and Development Program of ChinaProject(50325415) supported by the National Science Fund for Distinguished Young ScholarsProject(50574099) supported by the National Natural Science Foundation of China
文摘The pore structure images of ore particles located at different heights of leaching column were scanned with X-ray computerized tomography (CT) scanner, the porosity and pore size distribution were calculated and the geometrical shape and connectivity of pores were analyzed based on image process method, and the three dimensional reconstruction of pore structure images was realized. The results show that the porosity of ore particles bed in leaching column is 42.92%, 41.72%, 39.34% at top, middle and bottom zone, respectively. Obviously it has spatial variability and decreases appreciably along the height of the column. The overall average porosity obtained by image processing is 41.33% while the porosity gotten from general measurement method in laboratory is 42.77% showing the results of both methods are consistent well. The pore structure of ore granular media is characterized as a dynamical space network composed of interconnected pore bodies and pore throats. The ratio of throats with equivalent diameter less than 1.91 mm to the total pores is 29.31%, and that of the large pores with equivalent diameter more than 5.73 mm is 2.90%.
文摘The present article deals with thermally stratified stagnation-point flow saturated in porous medium on surface of variable thickness along with more convincing and reliable surface condition termed as melting heat transfer.Homogeneous–heterogeneous reaction and radiative effects have been further taken into account to reconnoiterproperties of heat transfer.Melting heat transfer and phenomenon of homogeneous–heterogeneous reaction have engrossed widespread utilization in purification of metals,welding process,electroslag melting,biochemical systems,catalysis and several industrial developments.Suitable transformations are utilized to attain a scheme of ordinary differential equations possessing exceedingly nonlinear nature.Homotopic process is employed to develop convergent solutions of the resulting problem.Discussion regarding velocity,thermal field and concentration distribution for several involved parameters is pivotal part.Graphical behaviors of skin friction coefficient and Nusselt number are also portrayed.Concentration of the reactants is found to depreciate as a result of strength of both heterogeneous and homogeneous reaction parameters.With existence of melting phenomenon,declining attitude of fluid temperature is observed for higher radiation parameter.
