In this paper, a photoelectric signal obtained scheme via equator triangle pattern engraved on rotor is discussed and the mathematic model is deduced in the case which is deflexion between rotor axis and the coordinat...In this paper, a photoelectric signal obtained scheme via equator triangle pattern engraved on rotor is discussed and the mathematic model is deduced in the case which is deflexion between rotor axis and the coordinate frame of case. The deflexion error and coupling error under the situation are analyzed. Finally, three methods of engraving based on the spherical triangle pattern are presented. The error models of various methods are built up and the simulation curves are provided respectively. We have done the primary experiments on the surface of rotor using this method. It can be seen from the enlarged figures that the rim of the pattern is smooth and the demand of sensor resolution is satisfied by and large. The results of study supply reference for signal obtaining.展开更多
Based on previous research results, this paper investigated the influence of fracture morphology on mechanical properties and failure modes of rock mass with two diagonal intersected fractures. This study carried out ...Based on previous research results, this paper investigated the influence of fracture morphology on mechanical properties and failure modes of rock mass with two diagonal intersected fractures. This study carried out a series of triaxial compression tests on rock-like specimens with two crossed fractures under negative temperature, concluded the following conclusions. The strength and failure modes of rock mass are significantly influenced by the dips of two crossed fractures. The strength of rock mass with two frac- tures cannot simply be estimated using the method that was developed for the rock mass with a single fracture. When the intersecting angle is less than 30~, the failure plane initiates at the tip of ＂artificial rup- tures＂ and extends to the upper and lower ends of the specimen. In case of a higher dip and intersecting angle ranging from 30° to 60°, the failure plane propagates along one of these two fractures. The mechan- lca! parameters of rock mass are not only related to the trace length, but also depend on the trace !ength ratio. One could roughly calculate the strength parameters using the approximation proposed in.this paper..For the rock mass with a trace length ratio 〈0.3 （short trace length/long trace length）, the failure mode is dependent on the fracture with a longer trace length. When the trace length becomes significant and the trace length ratio approximates to 1, the failure plane propagates along two fractures, where an X-shaped.failure pattern is presented： For the rock mass with moderate frac!ures and a trace length ratio of approxlmately 1, the failure mode Is.Independent on fractures, which is simllar to .the damage pattern of intact rock. The strength, and elastic .modulus of rock mass decrease with the increase of spacing between fractures, whl!e Polsson＇s ratio is Independent on the spacing. The failure mode can be deter- mined by the area. of triangle created by two fractures. Damage occurs at the smaller triangle area first, and propagates with the two sides of the larger triangle.展开更多
文摘In this paper, a photoelectric signal obtained scheme via equator triangle pattern engraved on rotor is discussed and the mathematic model is deduced in the case which is deflexion between rotor axis and the coordinate frame of case. The deflexion error and coupling error under the situation are analyzed. Finally, three methods of engraving based on the spherical triangle pattern are presented. The error models of various methods are built up and the simulation curves are provided respectively. We have done the primary experiments on the surface of rotor using this method. It can be seen from the enlarged figures that the rim of the pattern is smooth and the demand of sensor resolution is satisfied by and large. The results of study supply reference for signal obtaining.
文摘Based on previous research results, this paper investigated the influence of fracture morphology on mechanical properties and failure modes of rock mass with two diagonal intersected fractures. This study carried out a series of triaxial compression tests on rock-like specimens with two crossed fractures under negative temperature, concluded the following conclusions. The strength and failure modes of rock mass are significantly influenced by the dips of two crossed fractures. The strength of rock mass with two frac- tures cannot simply be estimated using the method that was developed for the rock mass with a single fracture. When the intersecting angle is less than 30~, the failure plane initiates at the tip of ＂artificial rup- tures＂ and extends to the upper and lower ends of the specimen. In case of a higher dip and intersecting angle ranging from 30° to 60°, the failure plane propagates along one of these two fractures. The mechan- lca! parameters of rock mass are not only related to the trace length, but also depend on the trace !ength ratio. One could roughly calculate the strength parameters using the approximation proposed in.this paper..For the rock mass with a trace length ratio 〈0.3 （short trace length/long trace length）, the failure mode is dependent on the fracture with a longer trace length. When the trace length becomes significant and the trace length ratio approximates to 1, the failure plane propagates along two fractures, where an X-shaped.failure pattern is presented： For the rock mass with moderate frac!ures and a trace length ratio of approxlmately 1, the failure mode Is.Independent on fractures, which is simllar to .the damage pattern of intact rock. The strength, and elastic .modulus of rock mass decrease with the increase of spacing between fractures, whl!e Polsson＇s ratio is Independent on the spacing. The failure mode can be deter- mined by the area. of triangle created by two fractures. Damage occurs at the smaller triangle area first, and propagates with the two sides of the larger triangle.
