To resolve the issue of design for multi-stage and multi-cluster fracturing in multi-zone reservoirs, a new efficient algorithm for the planar 3 D multi-fracture propagation model was proposed. The model considers flu...To resolve the issue of design for multi-stage and multi-cluster fracturing in multi-zone reservoirs, a new efficient algorithm for the planar 3 D multi-fracture propagation model was proposed. The model considers fluid flow in the wellbore-perforation-fracture system and fluid leak-off into the rock matrix, and uses a 3 D boundary integral equation to describe the solid deformation. The solid-fluid coupling equation is solved by an explicit integration algorithm, and the fracture front is determined by the uniform tip asymptotic solutions and shortest path algorithm. The accuracy of the algorithm is verified by the analytical solution of radial fracture, results of the implicit level set algorithm, and results of organic glass fracturing experiment. Compared with the implicit level set algorithm(ILSA), the new algorithm is much higher in computation speed. The numerical case study is conducted based on a horizontal well in shale gas formation of Zhejiang oilfield. The impact of stress heterogeneity among multiple clusters and perforation number distribution on multi-fracture growth and fluid distribution among multiple fractures are analyzed by numerical simulation. The results show that reducing perforation number in each cluster can counteract the effect of stress contrast among perforation clusters. Adjusting perforation number in each cluster can promote uniform flux among clusters, and the perforation number difference should better be 1-2 among clusters. Increasing perforation number in the cluster with high in situ stress is conducive to uniform fluid partitioning. However, uniform fluid partitioning is not equivalent to uniform fracture geometry. The fracture geometry is controlled by the stress interference and horizontal principal stress profile jointly.展开更多
Aiming at the problems of large load of rotation drive system,low efficiency of torque transmission and high cost for operation and maintenance of liner steering drilling system for the horizontal well,a new method of...Aiming at the problems of large load of rotation drive system,low efficiency of torque transmission and high cost for operation and maintenance of liner steering drilling system for the horizontal well,a new method of liner differential rotary drilling with double tubular strings in the horizontal well is proposed.The technical principle of this method is revealed,supporting tools such as the differential rotation transducer,composite rotary steering system and the hanger are designed,and technological process is optimized.A tool face control technique of steering drilling assembly is proposed and the calculation model of extension limit of liner differential rotary drilling with double tubular strings in horizontal well is established.These results show that the liner differential rotary drilling with double tubular strings is equipped with measurement while drilling(MWD)and positive displacement motor(PDM),and directional drilling of horizontal well is realized by adjusting rotary speed of drill pipe to control the tool face of PDM.Based on the engineering case of deep coalbed methane horizontal well in the eastern margin of Ordos Basin,the extension limit of horizontal drilling with double tubular strings is calculated.Compared with the conventional liner drilling method,the liner differential rotary drilling with double tubular strings increases the extension limit value of horizontal well significantly.The research findings provide useful reference for the integrated design and control of liner completion and drilling of horizontal wells.展开更多
The development of steam chamber can be used to evaluate steam-assisted gravity drainage(SAGD) performance. The velocity of steam chamber expanding is the key parameter for evaluating the development of steam chamber....The development of steam chamber can be used to evaluate steam-assisted gravity drainage(SAGD) performance. The velocity of steam chamber expanding is the key parameter for evaluating the development of steam chamber. Based on SAGD technology theory and heat transfer theory, two calculation model methods, observation well temperature method and steam chamber edge method for estimating the horizontal expanding velocity of steam chamber, were presented. Through analyzing the monitoring data and numerical simulation results of a typical super heavy oil block developed by SAGD in Fengcheng oilfield in Xinjiang, NW China, the development patterns of steam chamber and temperature variation law in the observation well at different stages are determined. The observed temperature data was used to calculate steam chamber expanding velocity. The calculated chamber velocity at different time was applied to predict the temperature distribution of oil drainage zone at the edge of steam chamber and SAGD oil rate. The results indicate that temperature function of high temperature zone in the observation well temperature curve has a linear relationship with measuring depth.The characteristic section can be used to calculate key parameters such as the angle of the drainage interface, expanding edge and velocity of steam chamber. The field production data verify that the results of the two proposed methods of steam chamber growth are reliable and practical, which can provide theoretical support for the efficient development of SAGD.展开更多
Based on geological analysis,reservoir numerical simulation and production performance analysis,water-out performance and pattern of horizontal wells in Tarim marine sandstone reservoir were studied.Compared with cont...Based on geological analysis,reservoir numerical simulation and production performance analysis,water-out performance and pattern of horizontal wells in Tarim marine sandstone reservoir were studied.Compared with continental sandstone reservoirs,the marine sandstone reservoirs in Tarim Basin were characterized by low oil viscosity,good reservoir continuity,and development of interbeds,which together with the large amount of horizontal wells,resulted in fast production rate and high recovery degree of the reservoirs.The main controlling factors of uneven water-out in horizontal wells were reservoir seepage barrier,injection-production well pattern,and dominant seepage channel.Thus 9 types in 4 categories of typical water-out pattern of horizontal wells in Tarim marine sandstone reservoirs were identified,and water-out management measures were proposed for them respectively according to their water-out mechanism and remaining oil distribution characteristics.Finally,the water-out pattern can be identified based on the inflection characteristics of derivative curve of water-oil ratio.This study of the water-out pattern can provide guidance for the adjustment policy of water injection in horizontal wells in marine sandstone reservoirs of Tarim Oilfield.展开更多
Injecting CO_(2)when the gas reservoir of tight sandstone is depleted can achieve the dual purposes of greenhouse gas storage and enhanced gas recovery(CS-EGR).To evaluate the feasibility of CO_(2)injection to enhance...Injecting CO_(2)when the gas reservoir of tight sandstone is depleted can achieve the dual purposes of greenhouse gas storage and enhanced gas recovery(CS-EGR).To evaluate the feasibility of CO_(2)injection to enhance gas recovery and understand the production mechanism,a numerical simulation model of CS-EGR in multi-stage fracturing horizontal wells is established.The behavior of gas production and CO_(2)sequestration is then analyzed through numerical simulation,and the impact of fracture parameters on production performance is examined.Simulation results show that the production rate increases significantly and a large amount of CO_(2)is stored in the reservoir,proving the technical potential.However,hydraulic fractures accelerate CO_(2)breakthrough,resulting in lower gas recovery and lower CO_(2)storage than in gas reservoirs without fracturing.Increasing the length of hydraulic fractures can significantly increase CH4production,but CO_(2)breakthrough will advance.Staggered and spaced perforation of hydraulic fractures in injection wells and production wells changes the fluid flow path,which can delay CO_(2)breakthrough and benefit production efficiency.The fracture network of massive hydraulic fracturing has a positive effect on the CS-EGR.As a result,CH4production,gas recovery,and CO_(2)storage increase with the increase in stimulated reservoir volume.展开更多
Accurate diagnosis of fracture geometry and conductivity is of great challenge due to the complex morphology of volumetric fracture network. In this study, a DNN (deep neural network) model was proposed to predict fra...Accurate diagnosis of fracture geometry and conductivity is of great challenge due to the complex morphology of volumetric fracture network. In this study, a DNN (deep neural network) model was proposed to predict fracture parameters for the evaluation of the fracturing effects. Field experience and the law of fracture volume conservation were incorporated as physical constraints to improve the prediction accuracy due to small amount of data. A combined neural network was adopted to input both static geological and dynamic fracturing data. The structure of the DNN was optimized and the model was validated through k-fold cross-validation. Results indicate that this DNN model is capable of predicting the fracture parameters accurately with a low relative error of under 10% and good generalization ability. The adoptions of the combined neural network, physical constraints, and k-fold cross-validation improve the model performance. Specifically, the root-mean-square error (RMSE) of the model decreases by 71.9% and 56% respectively with the combined neural network as the input model and the consideration of physical constraints. The mean square error (MRE) of fracture parameters reduces by 75% because the k-fold cross-validation improves the rationality of data set dividing. The model based on the DNN with physical constraints proposed in this study provides foundations for the optimization of fracturing design and improves the efficiency of fracture diagnosis in tight oil and gas reservoirs.展开更多
This paper presents a new development scheme of simultaneous injection and production in a single horizontal well drilled for developing small block reservoirs or offshore reservoirs. It is possible to set special pac...This paper presents a new development scheme of simultaneous injection and production in a single horizontal well drilled for developing small block reservoirs or offshore reservoirs. It is possible to set special packers within the long completion horizontal interval to establish an injection zone and a production zone. This method can also be used in steam flooding after steam soak through a horizontal well. Simulation results showed that it was desirable to start steam flooding after six steam soaking cycles and at this time the oil/steam ratio was 0.25 and oil recovery efficiency was 23.48%. Steam flooding performance was affected by separation interval and steam injection rate. Reservoir numerical simulation indicated that maximum oil recovery would be achieved at a separation section of 40-50 m at steam injection rate of 100-180 t/d; and the larger the steam injection rate, the greater the water cut and pressure difference between injection zone and production zone. A steam injection rate of 120 t/d was suitable for steam flooding under practical injection-production conditions. All the results could be useful for the guidance of steam flooding projects.展开更多
The application of fluid diversion during hydraulic fracturing is an evolving technology and has become popular amongst E&P operators over the past few years.The primary objective of the fluid diversion is to impr...The application of fluid diversion during hydraulic fracturing is an evolving technology and has become popular amongst E&P operators over the past few years.The primary objective of the fluid diversion is to improve hydraulic fracturing treatment by increasing stimulated reservoir volume and improving hydrocarbon recovery.This is possible by achieving any of the following objectives:creating uniform distribution of treatment slurry within the target zone;treating unstimulated and under-stimulated zones;or by increasing fracture density by creating a complex fracture network.The fluid diversion application is also helpful in decreasing the number of stages(by increasing stage length)for multi-stage plug-n-perf(PnP)fracturing treatment.It is also applied to prevent fracture-driven interactions between adjacent wells,which is currently a major issue,especially in shale.In addition,for successful refracturing treatment,the diverter application is essential for isolating the existing fractures and redirecting the treatment slurry to the desired unstimulated zones.The diversion methods can be broadly categorized into the mechanical and chemical diversion.Several established mechanical diversion techniques are frac plugs,expandable casing patches,expandable liners,swellable packers,straddle packer assembly,sand plugs,frac sleeves,perforation ball sealers,and limited entry technique.The different chemical diversion techniques are particulates,fibers,gels,surfactants,perforation pods,and composite diverting.This paper describes the current status of established mechanical and chemical diverter technologies and examines their comparative advantages and challenges.Various techniques are suitable for diverter application,but the technique is selected based on the desired objective and conditions of the wellbore and reservoir.The general guidelines for selecting diversion techniques and operational considerations are also provided in the paper.The diagnosis of diversion treatment plays an essential role in diversion technique selection and optimization of selection parameters for the subsequent treatments.Therefore,the application of conventional surface pressure monitoring techniques and advanced diagnostic tools to evaluate diversion effectiveness are briefly described.Presently no standard laboratory testing method is established for the performance evaluation of diverting agents.Therefore,researchers have implemented various laboratory methods,which are briefly summarized in the paper.Significant insight into the diversion technology and guidelines for its selection and successful implementation is provided to help engineers to increase the effectiveness of hydraulic fracturing treatments.The limitations of individual diversion techniques are clarified,which provide the future scope of research for improvement in various diversion technologies.展开更多
A forward model for optical fiber strain was established based on a planar 3D multi-fracture model. Then the forward method calculating distributed fiber strain induced by multi-fracture growth was proposed. Based on ...A forward model for optical fiber strain was established based on a planar 3D multi-fracture model. Then the forward method calculating distributed fiber strain induced by multi-fracture growth was proposed. Based on this method, fiber strain evolution during fracturing of the horizontal well was numerically simulated. Fiber strain evolution induced by fracture growth can be divided into three stages: strain increasing, shrinkage convergence, and straight-line convergence, whereas the evolution of fiber strain rate has four stages: strain rate increasing, shrinkage convergence, straight-line convergence, and strain rate reversal after pumping stops. Fiber strain does not flip after pumping stop, while the strain rate flips after pumping stop so that strain rate can reflect injection dynamics. The time when the fracture extends to the fiber and inter-well pressure channeling can be identified by the straight-line convergence band of distributed fiber strain or strain rate, and the non-uniform growth of multiple fractures can be evaluated by using the instants of fractures reaching the fiber monitoring well.When the horizontal section of the fiber monitoring well is within the height range of a hydraulic fracture, the instant of the fracture reaching the fiber can be identified;otherwise, the converging band is not apparent. In multi-stage fracturing, under the influence of stress shadow from previous fracturing stages, the tensile region of fiber strain may not appear, but the fiber strain rate can effectively show the fracture growth behavior in each stage. The evolution law of fiber strain rate in single-stage fracturing can be applied to multi-stage fracturing.展开更多
To accurately measure and evaluate the oil-water production profile of horizontal wells, a dynamic measurement experiment of oil-water two-phase flow in horizontal wells and numerical simulation were combined to estab...To accurately measure and evaluate the oil-water production profile of horizontal wells, a dynamic measurement experiment of oil-water two-phase flow in horizontal wells and numerical simulation were combined to establish a method for measuring the partial phase flow rate of oil-water two-phase stratified flow in horizontal wells. An experimental work was performed in horizontal oil-water two-phase flow simulation well using combination production logging tool including mini-capacitance sensor and mini-spinner. The combination tool provides a recording of holdup and velocity profiles at five different heights of the borehole cross-section. The effect of total flow rate and water-cut on the response of spinner and capacitive sensor at five measured positions were investigated. The capacitance water holdup interpolation imaging algorithm was used to determine the local fluid property and oil-water interface height, and the measured local fluid speed was combined with the numerical simulation result to establish an optimal calculation model for obtaining the partial phase flow rate of the oil-water two-phase stratified flow in the horizontal well. The calculated flow rates of five measured points are basically consistent with the experimental data, the total flow rate and water holdup from calculation are in agreement with the set values in the experiment too, suggesting that the method has high accuracy.展开更多
SAGD horizontal wells are used to enhance oil recovery from heavy oil reservoirs.This technology requires precise separation between the production well and the injection well to ensure the efficient drainage of the r...SAGD horizontal wells are used to enhance oil recovery from heavy oil reservoirs.This technology requires precise separation between the production well and the injection well to ensure the efficient drainage of the reservoir.By studying the attitude of the downhole probe tube and the production well trajectory,an algorithm is proposed for eliminating ferromagnetic interference while drilling injection wells.A high accuracy filter circuit has been designed to correct the detected magnetic signals,which are ultra-weak,frequency-instable,and narrow-band.The directional drilling magnetic guidance system（DD-MGS） has been developed by integrating these advanced techniques.It contains a sub-system for the ranging calculation software,a magnetic source,a downhole probe tube and a sub-system for collecting ＆ processing the detected signals.The DD-MGS has succeeded in oilfield applications.It can guide the directional drilling trajectory not only in the horizontal section but also in the build section of horizontal injection wells.This new technology has broad potential applications.展开更多
Barrier impacts on water cut and critical rate of horizontal wells in bottom water-drive reservoirs have been recognized but not investigated quantitatively. Considering the existence of impermeable barriers in oil fo...Barrier impacts on water cut and critical rate of horizontal wells in bottom water-drive reservoirs have been recognized but not investigated quantitatively. Considering the existence of impermeable barriers in oil formations, this paper developed a horizontal well flow model and obtained mathematical equations for the critical rate when water cresting forms in bottom-water reservoirs. The result shows that the barrier increases the critical rate and delays water breakthrough. Further study of the barrier size and location shows that increases in the barrier size and the distance between the barrier and oil-water contact lead to higher critical rates. The critical rate gradually approaches a constant as the barrier size increases. The case study shows the method presented here can be used to predict the critical rate in a bottom-water reservoir and applied to investigate the water cresting behavior of horizontal wells.展开更多
Early water breakthrough and a rapid increase in water cut are always observed in high- permeability completion intervals when perforations are uniformly distributed in the wellbore in heterogeneous reservoirs. Optimi...Early water breakthrough and a rapid increase in water cut are always observed in high- permeability completion intervals when perforations are uniformly distributed in the wellbore in heterogeneous reservoirs. Optimization of perforating parameters in partitioned sections in horizontal intervals helps homogenize the inflow from the reservoir and thus is critically important for enhanced oil recovery. This paper derives a coupled reservoir-wellbore flow model based on inflow controlling theory. Genetic algorithms are applied to solving the model as they excel in obtaining the global optimum of discrete functions. The optimized perforating strategy applies a low perforation density in high- permeability intervals and a high perforation density in low-permeability intervals. As a result, the inflow profile is homogenized and idealized.展开更多
Electromagnetic logging while drilling(LWD)is one of the key technologies of the geosteering and formation evaluation for high-angle and horizontal wells.In this paper,we solve the dipole source-generated magnetic/ele...Electromagnetic logging while drilling(LWD)is one of the key technologies of the geosteering and formation evaluation for high-angle and horizontal wells.In this paper,we solve the dipole source-generated magnetic/electric fields in 2D formations efficiently by the 2.5D finite diff erence method.Particularly,by leveraging the field’s rapid attenuation in spectral domain,we propose truncated Gauss–Hermite quadrature,which is several tens of times faster than traditional inverse fast Fourier transform.By applying the algorithm to the LWD modeling under complex formations,e.g.,folds,fault and sandstone pinch-outs,we analyze the feasibility of the dimension reduction from 2D to 1D.For the formations with smooth lateral changes,like folds,the simplified 1D model’s results agree well with the true responses,which indicate that the 1D simplification with sliding window is feasible.However,for the formation structures with drastic rock properties changes and sharp boundaries,for instance,faults and sandstone pinch-outs,the simplified 1D model will lead to large errors and,therefore,2.5D algorithms should be applied to ensure the accuracy.展开更多
It is very difficult to evaluate the productivity of horizontal wells in fault block reservoirs due to the influence of fault sealing.On the basis of the method of images and source-sink theory,a semianalytical model ...It is very difficult to evaluate the productivity of horizontal wells in fault block reservoirs due to the influence of fault sealing.On the basis of the method of images and source-sink theory,a semianalytical model coupling reservoir and finite conductivity horizontal wellbore flow dynamics was built,in which the influence of fault sealing was taken into account.The distribution of wellbore flow and radial inflow profiles along the horizontal interval were also obtained.The impact of the distance between the horizontal well and the fault on the well productivity was quantitatively analyzed.Based on this analysis,the optimal distance between the horizontal well and the fault in banded fault block reservoirs could be determined.According to the field application,the relative error calculated by the model proposed in this paper is within ±15%.It is an effective evaluation method for the productivity of horizontal wells in fault block reservoirs.The productivity of the horizontal well increases logarithmically as the distance between the horizontal well and the fault increases.The optimal distance between the horizontal well and the fault is 0.25-0.3 times the horizontal well length.展开更多
Based on the pseudo-analytical equation of electromagnetic log for layered formation,an optimal boundary match method is proposed to adaptively truncate the encountered formation structures.An efficient integral metho...Based on the pseudo-analytical equation of electromagnetic log for layered formation,an optimal boundary match method is proposed to adaptively truncate the encountered formation structures.An efficient integral method is put forward to significantly accelerate the convergence of Sommerfeld integral.By asymptotically approximating and subtracting the first reflection/transmission waves from the scattered field,the new Sommerfeld integral method has addressed difficulties encountered by the traditional digital filtering method,such as low computational precision and limited operating range,and realized the acceleration of the computation speed of logging-while-drilling electromagnetic measurements(LWD EM).By making use of the priori information from the offset/pilot wells and interactively adjusting the formation model,the optimum initial guesses of the inversion model is determined in order to predict the nearby formation boundaries.The gradient optimization algorithm is developed and an interactive inversion system for the LWD EM data from the horizontal wells is established.The inverted results of field data demonstrated that the real-time interactive inversion method is capable of providing the accurate boundaries of layers around the wellbore from the LWD EM,and it will benefit the wellbore trajectory optimization and reservoir interpretation.展开更多
Horizontal wells in the anisotropic reservoirs can be stimulated by hydraulic fracturing in order to create multiple finite-conductivity vertical fractures. Several methods for evaluating the productivity of the horiz...Horizontal wells in the anisotropic reservoirs can be stimulated by hydraulic fracturing in order to create multiple finite-conductivity vertical fractures. Several methods for evaluating the productivity of the horizontal wells have been presented in the literature. With such methods, however, it is still difficult to obtain an accurate result. This paper firstly presents the dimensionless conductivity theory of vertical fractures. Then models for calculating the equivalent wellbore radius and the skin factor due to flow convergence to the well bore are proposed after analyzing the steady-state flow in porous reservoirs. By applying the superposition principle to the pressure drop, a new method for evaluating the productivity of horizontal wells intercepted by multiple finite-conductivity fractures is developed. The influence of fracture conductivity and fracture half length on the horizontal well productivity is quantitatively analyzed with a synthetic case. Optimum fracture number and fracture space are further discussed in this study. The results prove that the method outlined here should be useful to design optimum fracturing of horizontal wells.展开更多
Multi-stage hydraulic fracturing of horizontal wells is the main stimulation method in recovering gas from tight shale gas reservoirs, and stage spacing deter- mination is one of the key issues in fracturing design. T...Multi-stage hydraulic fracturing of horizontal wells is the main stimulation method in recovering gas from tight shale gas reservoirs, and stage spacing deter- mination is one of the key issues in fracturing design. The initiation and propagation of hydraulic fractures will cause stress redistribution and may activate natural fractures in the reservoir. Due to the limitation of the analytical method in calculation of induced stresses, we propose a numerical method, which incorporates the interaction of hydraulic fractures and the wellbore, and analyzes the stress distri- bution in the reservoir under different stage spacing. Simulation results indicate the following： （1） The induced stress was overestimated from the analytical method because it did not take into account the interaction between hydraulic fractures and the horizontal wellbore. （2） The hydraulic fracture had a considerable effect on the redis- tribution of stresses in the direction of the horizontal wellbore in the reservoir. The stress in the direction per- pendicular to the horizontal wellbore after hydraulic frac- turing had a minor change compared with the original in situ stress. （3） Stress interferences among fractures were greatly connected with the stage spacing and the distance from the wellbore. When the fracture length was 200 m, and the stage spacing was 50 m, the stress redistribution due to stage fracturing may divert the original stress pat- tern, which might activate natural fractures so as to generate a complex fracture network.展开更多
基金China National Science and Technology Major Project(2016ZX05023).
文摘To resolve the issue of design for multi-stage and multi-cluster fracturing in multi-zone reservoirs, a new efficient algorithm for the planar 3 D multi-fracture propagation model was proposed. The model considers fluid flow in the wellbore-perforation-fracture system and fluid leak-off into the rock matrix, and uses a 3 D boundary integral equation to describe the solid deformation. The solid-fluid coupling equation is solved by an explicit integration algorithm, and the fracture front is determined by the uniform tip asymptotic solutions and shortest path algorithm. The accuracy of the algorithm is verified by the analytical solution of radial fracture, results of the implicit level set algorithm, and results of organic glass fracturing experiment. Compared with the implicit level set algorithm(ILSA), the new algorithm is much higher in computation speed. The numerical case study is conducted based on a horizontal well in shale gas formation of Zhejiang oilfield. The impact of stress heterogeneity among multiple clusters and perforation number distribution on multi-fracture growth and fluid distribution among multiple fractures are analyzed by numerical simulation. The results show that reducing perforation number in each cluster can counteract the effect of stress contrast among perforation clusters. Adjusting perforation number in each cluster can promote uniform flux among clusters, and the perforation number difference should better be 1-2 among clusters. Increasing perforation number in the cluster with high in situ stress is conducive to uniform fluid partitioning. However, uniform fluid partitioning is not equivalent to uniform fracture geometry. The fracture geometry is controlled by the stress interference and horizontal principal stress profile jointly.
基金Supported by the Project of National Natural Science Foundation of China(52234002,42230814)。
文摘Aiming at the problems of large load of rotation drive system,low efficiency of torque transmission and high cost for operation and maintenance of liner steering drilling system for the horizontal well,a new method of liner differential rotary drilling with double tubular strings in the horizontal well is proposed.The technical principle of this method is revealed,supporting tools such as the differential rotation transducer,composite rotary steering system and the hanger are designed,and technological process is optimized.A tool face control technique of steering drilling assembly is proposed and the calculation model of extension limit of liner differential rotary drilling with double tubular strings in horizontal well is established.These results show that the liner differential rotary drilling with double tubular strings is equipped with measurement while drilling(MWD)and positive displacement motor(PDM),and directional drilling of horizontal well is realized by adjusting rotary speed of drill pipe to control the tool face of PDM.Based on the engineering case of deep coalbed methane horizontal well in the eastern margin of Ordos Basin,the extension limit of horizontal drilling with double tubular strings is calculated.Compared with the conventional liner drilling method,the liner differential rotary drilling with double tubular strings increases the extension limit value of horizontal well significantly.The research findings provide useful reference for the integrated design and control of liner completion and drilling of horizontal wells.
基金Supported by the China National Science and Technology Major Project(2016ZX05012-002)
文摘The development of steam chamber can be used to evaluate steam-assisted gravity drainage(SAGD) performance. The velocity of steam chamber expanding is the key parameter for evaluating the development of steam chamber. Based on SAGD technology theory and heat transfer theory, two calculation model methods, observation well temperature method and steam chamber edge method for estimating the horizontal expanding velocity of steam chamber, were presented. Through analyzing the monitoring data and numerical simulation results of a typical super heavy oil block developed by SAGD in Fengcheng oilfield in Xinjiang, NW China, the development patterns of steam chamber and temperature variation law in the observation well at different stages are determined. The observed temperature data was used to calculate steam chamber expanding velocity. The calculated chamber velocity at different time was applied to predict the temperature distribution of oil drainage zone at the edge of steam chamber and SAGD oil rate. The results indicate that temperature function of high temperature zone in the observation well temperature curve has a linear relationship with measuring depth.The characteristic section can be used to calculate key parameters such as the angle of the drainage interface, expanding edge and velocity of steam chamber. The field production data verify that the results of the two proposed methods of steam chamber growth are reliable and practical, which can provide theoretical support for the efficient development of SAGD.
基金Supported by the National Key Basic Research and Development Program(973 Program),China(2015CB250900)
文摘Based on geological analysis,reservoir numerical simulation and production performance analysis,water-out performance and pattern of horizontal wells in Tarim marine sandstone reservoir were studied.Compared with continental sandstone reservoirs,the marine sandstone reservoirs in Tarim Basin were characterized by low oil viscosity,good reservoir continuity,and development of interbeds,which together with the large amount of horizontal wells,resulted in fast production rate and high recovery degree of the reservoirs.The main controlling factors of uneven water-out in horizontal wells were reservoir seepage barrier,injection-production well pattern,and dominant seepage channel.Thus 9 types in 4 categories of typical water-out pattern of horizontal wells in Tarim marine sandstone reservoirs were identified,and water-out management measures were proposed for them respectively according to their water-out mechanism and remaining oil distribution characteristics.Finally,the water-out pattern can be identified based on the inflection characteristics of derivative curve of water-oil ratio.This study of the water-out pattern can provide guidance for the adjustment policy of water injection in horizontal wells in marine sandstone reservoirs of Tarim Oilfield.
基金the financial support of the National Natural Science Foundation of China(Grant No.52304018)China Postdoctoral Science Foundation(Grant No.2023TQ0014,Grant No.2023M730088)。
文摘Injecting CO_(2)when the gas reservoir of tight sandstone is depleted can achieve the dual purposes of greenhouse gas storage and enhanced gas recovery(CS-EGR).To evaluate the feasibility of CO_(2)injection to enhance gas recovery and understand the production mechanism,a numerical simulation model of CS-EGR in multi-stage fracturing horizontal wells is established.The behavior of gas production and CO_(2)sequestration is then analyzed through numerical simulation,and the impact of fracture parameters on production performance is examined.Simulation results show that the production rate increases significantly and a large amount of CO_(2)is stored in the reservoir,proving the technical potential.However,hydraulic fractures accelerate CO_(2)breakthrough,resulting in lower gas recovery and lower CO_(2)storage than in gas reservoirs without fracturing.Increasing the length of hydraulic fractures can significantly increase CH4production,but CO_(2)breakthrough will advance.Staggered and spaced perforation of hydraulic fractures in injection wells and production wells changes the fluid flow path,which can delay CO_(2)breakthrough and benefit production efficiency.The fracture network of massive hydraulic fracturing has a positive effect on the CS-EGR.As a result,CH4production,gas recovery,and CO_(2)storage increase with the increase in stimulated reservoir volume.
基金supported by the National Natural Science Foundation of China(Grant No.52174044,52004302)Science Foundation of China University of Petroleum,Beijing(No.ZX20200134,2462021YXZZ012)the Strategic Cooperation Technology Projects of CNPC and CUPB(ZLZX 2020-01-07).
文摘Accurate diagnosis of fracture geometry and conductivity is of great challenge due to the complex morphology of volumetric fracture network. In this study, a DNN (deep neural network) model was proposed to predict fracture parameters for the evaluation of the fracturing effects. Field experience and the law of fracture volume conservation were incorporated as physical constraints to improve the prediction accuracy due to small amount of data. A combined neural network was adopted to input both static geological and dynamic fracturing data. The structure of the DNN was optimized and the model was validated through k-fold cross-validation. Results indicate that this DNN model is capable of predicting the fracture parameters accurately with a low relative error of under 10% and good generalization ability. The adoptions of the combined neural network, physical constraints, and k-fold cross-validation improve the model performance. Specifically, the root-mean-square error (RMSE) of the model decreases by 71.9% and 56% respectively with the combined neural network as the input model and the consideration of physical constraints. The mean square error (MRE) of fracture parameters reduces by 75% because the k-fold cross-validation improves the rationality of data set dividing. The model based on the DNN with physical constraints proposed in this study provides foundations for the optimization of fracturing design and improves the efficiency of fracture diagnosis in tight oil and gas reservoirs.
文摘This paper presents a new development scheme of simultaneous injection and production in a single horizontal well drilled for developing small block reservoirs or offshore reservoirs. It is possible to set special packers within the long completion horizontal interval to establish an injection zone and a production zone. This method can also be used in steam flooding after steam soak through a horizontal well. Simulation results showed that it was desirable to start steam flooding after six steam soaking cycles and at this time the oil/steam ratio was 0.25 and oil recovery efficiency was 23.48%. Steam flooding performance was affected by separation interval and steam injection rate. Reservoir numerical simulation indicated that maximum oil recovery would be achieved at a separation section of 40-50 m at steam injection rate of 100-180 t/d; and the larger the steam injection rate, the greater the water cut and pressure difference between injection zone and production zone. A steam injection rate of 120 t/d was suitable for steam flooding under practical injection-production conditions. All the results could be useful for the guidance of steam flooding projects.
文摘The application of fluid diversion during hydraulic fracturing is an evolving technology and has become popular amongst E&P operators over the past few years.The primary objective of the fluid diversion is to improve hydraulic fracturing treatment by increasing stimulated reservoir volume and improving hydrocarbon recovery.This is possible by achieving any of the following objectives:creating uniform distribution of treatment slurry within the target zone;treating unstimulated and under-stimulated zones;or by increasing fracture density by creating a complex fracture network.The fluid diversion application is also helpful in decreasing the number of stages(by increasing stage length)for multi-stage plug-n-perf(PnP)fracturing treatment.It is also applied to prevent fracture-driven interactions between adjacent wells,which is currently a major issue,especially in shale.In addition,for successful refracturing treatment,the diverter application is essential for isolating the existing fractures and redirecting the treatment slurry to the desired unstimulated zones.The diversion methods can be broadly categorized into the mechanical and chemical diversion.Several established mechanical diversion techniques are frac plugs,expandable casing patches,expandable liners,swellable packers,straddle packer assembly,sand plugs,frac sleeves,perforation ball sealers,and limited entry technique.The different chemical diversion techniques are particulates,fibers,gels,surfactants,perforation pods,and composite diverting.This paper describes the current status of established mechanical and chemical diverter technologies and examines their comparative advantages and challenges.Various techniques are suitable for diverter application,but the technique is selected based on the desired objective and conditions of the wellbore and reservoir.The general guidelines for selecting diversion techniques and operational considerations are also provided in the paper.The diagnosis of diversion treatment plays an essential role in diversion technique selection and optimization of selection parameters for the subsequent treatments.Therefore,the application of conventional surface pressure monitoring techniques and advanced diagnostic tools to evaluate diversion effectiveness are briefly described.Presently no standard laboratory testing method is established for the performance evaluation of diverting agents.Therefore,researchers have implemented various laboratory methods,which are briefly summarized in the paper.Significant insight into the diversion technology and guidelines for its selection and successful implementation is provided to help engineers to increase the effectiveness of hydraulic fracturing treatments.The limitations of individual diversion techniques are clarified,which provide the future scope of research for improvement in various diversion technologies.
基金Supported by the National Natural Science Foundation of China(52104060)Project of Natural Science Outstanding Youth Foundation of Shandong(ZR2019QEE005)。
文摘A forward model for optical fiber strain was established based on a planar 3D multi-fracture model. Then the forward method calculating distributed fiber strain induced by multi-fracture growth was proposed. Based on this method, fiber strain evolution during fracturing of the horizontal well was numerically simulated. Fiber strain evolution induced by fracture growth can be divided into three stages: strain increasing, shrinkage convergence, and straight-line convergence, whereas the evolution of fiber strain rate has four stages: strain rate increasing, shrinkage convergence, straight-line convergence, and strain rate reversal after pumping stops. Fiber strain does not flip after pumping stop, while the strain rate flips after pumping stop so that strain rate can reflect injection dynamics. The time when the fracture extends to the fiber and inter-well pressure channeling can be identified by the straight-line convergence band of distributed fiber strain or strain rate, and the non-uniform growth of multiple fractures can be evaluated by using the instants of fractures reaching the fiber monitoring well.When the horizontal section of the fiber monitoring well is within the height range of a hydraulic fracture, the instant of the fracture reaching the fiber can be identified;otherwise, the converging band is not apparent. In multi-stage fracturing, under the influence of stress shadow from previous fracturing stages, the tensile region of fiber strain may not appear, but the fiber strain rate can effectively show the fracture growth behavior in each stage. The evolution law of fiber strain rate in single-stage fracturing can be applied to multi-stage fracturing.
基金Supported by National Natural Science Foundation of China(41474115)Open Fund of Key Laboratory of Exploration Technologies for Oil and Gas Resources(Yangtze University)Ministry of Education of China(No K2018-02)Educational Commission of Hubei Province of China(D20141302)
文摘To accurately measure and evaluate the oil-water production profile of horizontal wells, a dynamic measurement experiment of oil-water two-phase flow in horizontal wells and numerical simulation were combined to establish a method for measuring the partial phase flow rate of oil-water two-phase stratified flow in horizontal wells. An experimental work was performed in horizontal oil-water two-phase flow simulation well using combination production logging tool including mini-capacitance sensor and mini-spinner. The combination tool provides a recording of holdup and velocity profiles at five different heights of the borehole cross-section. The effect of total flow rate and water-cut on the response of spinner and capacitive sensor at five measured positions were investigated. The capacitance water holdup interpolation imaging algorithm was used to determine the local fluid property and oil-water interface height, and the measured local fluid speed was combined with the numerical simulation result to establish an optimal calculation model for obtaining the partial phase flow rate of the oil-water two-phase stratified flow in the horizontal well. The calculated flow rates of five measured points are basically consistent with the experimental data, the total flow rate and water holdup from calculation are in agreement with the set values in the experiment too, suggesting that the method has high accuracy.
基金the financial support from the Natural Science Foundation of China (NSFC, 51221003, U1262201)supported by other projects (Grant numbers: 2011ZX05009, 2013AA064803)
文摘SAGD horizontal wells are used to enhance oil recovery from heavy oil reservoirs.This technology requires precise separation between the production well and the injection well to ensure the efficient drainage of the reservoir.By studying the attitude of the downhole probe tube and the production well trajectory,an algorithm is proposed for eliminating ferromagnetic interference while drilling injection wells.A high accuracy filter circuit has been designed to correct the detected magnetic signals,which are ultra-weak,frequency-instable,and narrow-band.The directional drilling magnetic guidance system（DD-MGS） has been developed by integrating these advanced techniques.It contains a sub-system for the ranging calculation software,a magnetic source,a downhole probe tube and a sub-system for collecting ＆ processing the detected signals.The DD-MGS has succeeded in oilfield applications.It can guide the directional drilling trajectory not only in the horizontal section but also in the build section of horizontal injection wells.This new technology has broad potential applications.
基金supported by the National Science and Technology Major Project of China (No. 2011ZX05010-003)the National Natural Science Foundation of China (No. 10902093)
文摘Barrier impacts on water cut and critical rate of horizontal wells in bottom water-drive reservoirs have been recognized but not investigated quantitatively. Considering the existence of impermeable barriers in oil formations, this paper developed a horizontal well flow model and obtained mathematical equations for the critical rate when water cresting forms in bottom-water reservoirs. The result shows that the barrier increases the critical rate and delays water breakthrough. Further study of the barrier size and location shows that increases in the barrier size and the distance between the barrier and oil-water contact lead to higher critical rates. The critical rate gradually approaches a constant as the barrier size increases. The case study shows the method presented here can be used to predict the critical rate in a bottom-water reservoir and applied to investigate the water cresting behavior of horizontal wells.
基金supported by National Scientific Project(No. 2008ZX05024-03)
文摘Early water breakthrough and a rapid increase in water cut are always observed in high- permeability completion intervals when perforations are uniformly distributed in the wellbore in heterogeneous reservoirs. Optimization of perforating parameters in partitioned sections in horizontal intervals helps homogenize the inflow from the reservoir and thus is critically important for enhanced oil recovery. This paper derives a coupled reservoir-wellbore flow model based on inflow controlling theory. Genetic algorithms are applied to solving the model as they excel in obtaining the global optimum of discrete functions. The optimized perforating strategy applies a low perforation density in high- permeability intervals and a high perforation density in low-permeability intervals. As a result, the inflow profile is homogenized and idealized.
基金the National Natural Science Foundation of China (41674131,41574118,41974146,41904109)the Fundamental Research Funds for the Central Universities (17CX06041,17CX06044)the China National Science and Technology Major Project (2016ZX05007-004,2017ZX05072-002)
文摘Electromagnetic logging while drilling(LWD)is one of the key technologies of the geosteering and formation evaluation for high-angle and horizontal wells.In this paper,we solve the dipole source-generated magnetic/electric fields in 2D formations efficiently by the 2.5D finite diff erence method.Particularly,by leveraging the field’s rapid attenuation in spectral domain,we propose truncated Gauss–Hermite quadrature,which is several tens of times faster than traditional inverse fast Fourier transform.By applying the algorithm to the LWD modeling under complex formations,e.g.,folds,fault and sandstone pinch-outs,we analyze the feasibility of the dimension reduction from 2D to 1D.For the formations with smooth lateral changes,like folds,the simplified 1D model’s results agree well with the true responses,which indicate that the 1D simplification with sliding window is feasible.However,for the formation structures with drastic rock properties changes and sharp boundaries,for instance,faults and sandstone pinch-outs,the simplified 1D model will lead to large errors and,therefore,2.5D algorithms should be applied to ensure the accuracy.
基金support from the National Science & Technology Major Project of China (No. 2009ZX05009-006)the China National Offshore Oil Corporation (CNOOC)
文摘It is very difficult to evaluate the productivity of horizontal wells in fault block reservoirs due to the influence of fault sealing.On the basis of the method of images and source-sink theory,a semianalytical model coupling reservoir and finite conductivity horizontal wellbore flow dynamics was built,in which the influence of fault sealing was taken into account.The distribution of wellbore flow and radial inflow profiles along the horizontal interval were also obtained.The impact of the distance between the horizontal well and the fault on the well productivity was quantitatively analyzed.Based on this analysis,the optimal distance between the horizontal well and the fault in banded fault block reservoirs could be determined.According to the field application,the relative error calculated by the model proposed in this paper is within ±15%.It is an effective evaluation method for the productivity of horizontal wells in fault block reservoirs.The productivity of the horizontal well increases logarithmically as the distance between the horizontal well and the fault increases.The optimal distance between the horizontal well and the fault is 0.25-0.3 times the horizontal well length.
基金Supported by the National Natural Science Foundation of China(41904109,41974146)National Science and Technology Major Project(2017ZX05019-005)+2 种基金China Postdoctoral Science Foundation(2018M640663)the Shandong Province Postdoctoral Innovation Projects(sdbh20180025)National Key Laboratory of Electromagnetic Environment Projects(6142403200307)。
文摘Based on the pseudo-analytical equation of electromagnetic log for layered formation,an optimal boundary match method is proposed to adaptively truncate the encountered formation structures.An efficient integral method is put forward to significantly accelerate the convergence of Sommerfeld integral.By asymptotically approximating and subtracting the first reflection/transmission waves from the scattered field,the new Sommerfeld integral method has addressed difficulties encountered by the traditional digital filtering method,such as low computational precision and limited operating range,and realized the acceleration of the computation speed of logging-while-drilling electromagnetic measurements(LWD EM).By making use of the priori information from the offset/pilot wells and interactively adjusting the formation model,the optimum initial guesses of the inversion model is determined in order to predict the nearby formation boundaries.The gradient optimization algorithm is developed and an interactive inversion system for the LWD EM data from the horizontal wells is established.The inverted results of field data demonstrated that the real-time interactive inversion method is capable of providing the accurate boundaries of layers around the wellbore from the LWD EM,and it will benefit the wellbore trajectory optimization and reservoir interpretation.
文摘Horizontal wells in the anisotropic reservoirs can be stimulated by hydraulic fracturing in order to create multiple finite-conductivity vertical fractures. Several methods for evaluating the productivity of the horizontal wells have been presented in the literature. With such methods, however, it is still difficult to obtain an accurate result. This paper firstly presents the dimensionless conductivity theory of vertical fractures. Then models for calculating the equivalent wellbore radius and the skin factor due to flow convergence to the well bore are proposed after analyzing the steady-state flow in porous reservoirs. By applying the superposition principle to the pressure drop, a new method for evaluating the productivity of horizontal wells intercepted by multiple finite-conductivity fractures is developed. The influence of fracture conductivity and fracture half length on the horizontal well productivity is quantitatively analyzed with a synthetic case. Optimum fracture number and fracture space are further discussed in this study. The results prove that the method outlined here should be useful to design optimum fracturing of horizontal wells.
基金supported by the Natural Science Foundation of China (Grant No. 51490653, Basic Theoretical Research of Shale Oil and Gas Effective Development)
文摘Multi-stage hydraulic fracturing of horizontal wells is the main stimulation method in recovering gas from tight shale gas reservoirs, and stage spacing deter- mination is one of the key issues in fracturing design. The initiation and propagation of hydraulic fractures will cause stress redistribution and may activate natural fractures in the reservoir. Due to the limitation of the analytical method in calculation of induced stresses, we propose a numerical method, which incorporates the interaction of hydraulic fractures and the wellbore, and analyzes the stress distri- bution in the reservoir under different stage spacing. Simulation results indicate the following： （1） The induced stress was overestimated from the analytical method because it did not take into account the interaction between hydraulic fractures and the horizontal wellbore. （2） The hydraulic fracture had a considerable effect on the redis- tribution of stresses in the direction of the horizontal wellbore in the reservoir. The stress in the direction per- pendicular to the horizontal wellbore after hydraulic frac- turing had a minor change compared with the original in situ stress. （3） Stress interferences among fractures were greatly connected with the stage spacing and the distance from the wellbore. When the fracture length was 200 m, and the stage spacing was 50 m, the stress redistribution due to stage fracturing may divert the original stress pat- tern, which might activate natural fractures so as to generate a complex fracture network.
