A new adsorbent was successfully prepared by hydrothermal treatment and chemical activation through coal gasification fine slag(CGFS)and blue algae(BA)as raw materials and used for CO_(2)capture.The CO_(2)chemisorptio...A new adsorbent was successfully prepared by hydrothermal treatment and chemical activation through coal gasification fine slag(CGFS)and blue algae(BA)as raw materials and used for CO_(2)capture.The CO_(2)chemisorption capacity of the adsorbent was further enhanced by taking advantage of the nitrogenous bases contained in the BA.In the hydrothermal process,the addition of BA significantly increased the content of pyrrole nitrogen in the adsorbent.In the activation process,pyrrole nitrogen gradually changed into pyridine nitrogen and graphite nitrogen.Increased BA addition result in a higher specific surface area and microporosity of the adsorbent.The CO_(2)adsorption performance test proved that the CGFS-50%-CA sample has the strongest CO_(2)adsorption capacity at low temperature,up to 15.59 cm^(3)/g,which is mainly through physical adsorption,and the CGFS-10%-CA sample has the strongest CO_(2)adsorption capacity at high temperature,up to 7.31 cm^(3)/g,which is mainly through chemical adsorption.CO_(2)uptake of the CGFS-10%-CA sample was well maintained after 10 cycles,with regeneration efficiencies above 99%.The results indicate that the novel adsorbents with coexistence of physical and chemical adsorption have great potential for CO_(2)adsorption applications.展开更多
The use of carbon from waste biomass has the potential to eliminate the drawbacks of Li-S batteries and improve their overall performance.Chrome-tanned-leather-shavings(CTLS)are a readily available waste product that ...The use of carbon from waste biomass has the potential to eliminate the drawbacks of Li-S batteries and improve their overall performance.Chrome-tanned-leather-shavings(CTLS)are a readily available waste product that can be transformed into porous carbon.We prepared an ac-tivated carbon by microwave pyrolysis combined with KOH activator using the CTLS as starting materials.The carbon had a specific surface area of 556 m^(2)g^(-1) and a honeycomb-like structure.Two kinds of N-doped activated carbons were then synthesized by thermal decomposition of the activated carbon,either combined with urea,or impregnated with eth-anolamine.Both N-doped activated carbons have an in-creased number of nitrogen and amine surface groups.However,only the urea treatment was effective in improv-ing the initial capacity of the cell(1363 mAh g^(-1)),which is probably linked to the sorption of long-chain polysulfides.This investigation confirms that it is possible to use the thermal de-composition of urea to obtain carbon materials from CTLS for use as the sulfur-host cathode in Li-S batteries and improve their performance.A radial basis function neural network was fitted to provide statistical support for the experimental results,which confirmed the importance of the nitrogen content of the carbons in determining the discharge capacity of the cells.展开更多
Driven by rapid technological advancements and economic growth,mineral extraction and metal refining have increased dramatically,generating huge volumes of tailings and mine waste(TMWs).Investigating the morphological...Driven by rapid technological advancements and economic growth,mineral extraction and metal refining have increased dramatically,generating huge volumes of tailings and mine waste(TMWs).Investigating the morphological fractions of heavy metals and metalloids(HMMs)in TMWs is key to evaluating their leaching potential into the environment;however,traditional experiments are time-consuming and labor-intensive.In this study,10 machine learning(ML)algorithms were used and compared for rapidly predicting the morphological fractions of HMMs in TMWs.A dataset comprising 2376 data points was used,with mineral composition,elemental properties,and total concentration used as inputs and concentration of morphological fraction used as output.After grid search optimization,the extra tree model performed the best,achieving coefficient of determination(R2)of 0.946 and 0.942 on the validation and test sets,respectively.Electronegativity was found to have the greatest impact on the morphological fraction.The models’performance was enhanced by applying an ensemble method to the top three optimal ML models,including gradient boosting decision tree,extra trees and categorical boosting.Overall,the proposed framework can accurately predict the concentrations of different morphological fractions of HMMs in TMWs.This approach can minimize detection time,aid in the safe management and recovery of TMWs.展开更多
China has a large solid waste stockpile and a low resource utilisation rate,and the utilisation of solid waste resources is of great significance in promoting sustainable social development.In order to further promote...China has a large solid waste stockpile and a low resource utilisation rate,and the utilisation of solid waste resources is of great significance in promoting sustainable social development.In order to further promote the green and efficient development of China's road field,an overview of the current status of the application,research progress,hot frontiers,problems and their countermeasures based on the three aspects of industrial solid wastes,engineering solid wastes and municipal solid wastes in highway engineering was conducted,and the development prospect of the resourceful utilisation of solid waste in highway engineering was outlooked,with a view to promoting the development of China's green roads.Statistics on the stockpile,utilisation and comprehensive utilisation rate of industrial solid wastes in China are presented,and the optimal mixing amount,production process and application technology of industrial solid wastes for road base materials are systematically summarised.Based on the concept of high-value utilisation of solid waste,the mechanical properties,durability,construction technology and quality control standards of engineering solid waste applied in roadbed engineering are summarised,and the difficulties in the application of engineering solid waste in road engineering are summarised.Finally,the feasibility,mechanical properties and environmental characteristics of municipal solid waste domestic waste incinerator slag,waste tyres and plastics applied in road engineering are summarised.This review can provide references and lessons for the design and development of green roads,and promote the innovation and development of greening road engineering.展开更多
The mechanism of removing phosphate by MSWI(municipal solid waste incineration)fly ash was investigated by SEM(scanning electron microscopy)with EDS(energy dispersion spectrum),XRD(X-ray diffraction),FT-IR(Fourier tra...The mechanism of removing phosphate by MSWI(municipal solid waste incineration)fly ash was investigated by SEM(scanning electron microscopy)with EDS(energy dispersion spectrum),XRD(X-ray diffraction),FT-IR(Fourier transform infrared spectroscopy),BET(specific surface area),and BJH(pore size distribution).The results indicate that the removal rate of phosphate(100 mg/L)in 50 mL phosphorus wastewater reaches at 99.9% as the dosage of MSWI fly ash being 0.9000 g under room temperature.The specific surface area of MSWI fly ash is less than 6.1 m2/g and the total pore volume is below 0.021 cm3/g,suggesting that the absorption capacity of calcite is too weak to play an important role in phosphate removal.SEM images show that drastic changes had taken place on its specific surface shape after reaction,and EDS tests indicate that some phosphate precipitates are formed and attached onto MSWI fly ash particles.Chemical precipitation is the main manner of phosphate removal and the main reaction is: 3Ca2++2 PO4 3-+xH2O→Ca3(PO4)2↓·xH2O.Besides,XRD tests show that the composition of MSWI fly ash is complex,but CaSO4 is likely to be the main source of Ca2+.The soluble heavy metals in MSWI fly ash are stabilized by phosphate.展开更多
Integrating disaster waste issue is a critical component of making humanitarian action fit for the future,anticipating global risks and challenges such as increased vulnerability due to climate change and environmenta...Integrating disaster waste issue is a critical component of making humanitarian action fit for the future,anticipating global risks and challenges such as increased vulnerability due to climate change and environmental degradation.This requires a fundamental shift towards a model that not only strengthens the response to crises but also learns and adapts in order to anticipate and act before such waste garnered.This article conducted analyses on the characteristics of disasters in the past two decades.Uncertainties confound disaster waste management,including the timing and magnitude of each disaster,and the amounts and types of waste that will be generated.For these reasons alone,disaster waste management must be an integral part of development planning and processes.Making 10 years since the 2008 Wenchuan earthquake,this article highlights that disaster waste management is not only debris clearance or waste management following a disaster,but also includes prevention and pre-disaster preparedness aspects in terms of enhancing resilience of local communities.Such"mainstreaming,"ensures that disaster waste management(DWM)will be treated as a priority issue,on an ongoing basis.Based on UN Environment's experiences and approaches,this paper emphasises that preparedness is the key,and that priority should be accorded to integrating disaster contingency planning in national and city level waste management strategies as well as mainstreaming waste management issues within broader disaster preparedness and response plans and actions.It is envisaged that the issues presented and the gaps identified in this paper will provide a basis for future comprehensive and cohesive research on disaster waste management.In turn,this research can lead to better preparedness and response on disaster waste management.展开更多
The micro-nuclei and abnormal nuclei rates of peacock fish are tested,genetic toxic effects of rare-earth waste and its products(cement,plastic) on peacock in water are investigated.Results show that the leachate of r...The micro-nuclei and abnormal nuclei rates of peacock fish are tested,genetic toxic effects of rare-earth waste and its products(cement,plastic) on peacock in water are investigated.Results show that the leachate of rare-earth waste can lead to micronuclei and abnormal nuclei rates of peacock fish an obvious increase(P<0.01). Products made of the waste cause the micronuclei rate to be increased because of its low radio active action,but the change in abnormal nuclei rate can't reach a remarkable level.It shows that rare-earth waste has a certain effect of causing mutation on aquatic organism.Harmfulness of products made from this waste is decreased largely,and resources can be effectively saved.展开更多
Bauxite residue is a highly alkaline material generated from the production of alumina in which bauxite is dissolved in caustic soda.Approximately 4.4 billion tons of bauxite residues are either stockpiled or landfill...Bauxite residue is a highly alkaline material generated from the production of alumina in which bauxite is dissolved in caustic soda.Approximately 4.4 billion tons of bauxite residues are either stockpiled or landfilled,creating environmental risks either from the generation of dust or migration of filtrates.High alkalinity is the critical factor restricting complete utilization of bauxite residues,whilst the application of alkaline regulation agents is costly and difficult to apply widely.For now,current industrial wastes,such as waste acid,ammonia nitrogen wastewater,waste gypsum and biomass,have become major problems restricting the development of the social economy.Regulation of bauxite residues alkalinity by industrial waste was proposed to achieve‘waste control by waste’with good economic and ecological benefits.This review will focus on the origin and transformation of alkalinity in bauxite residues using typical industrial waste.It will propose key research directions with an emphasis on alkaline regulation by industrial waste,whilst also providing a scientific reference point for their potential use as amendments to enhance soil formation and establish vegetation on bauxite residue disposal areas(BRDAs)following large-scale disposal.展开更多
In this work,a novel alcohol alkali hydrolysis method was explored for the preparation of terephthalic acid(TPA)from waste polyethylene terephthalate(PET).First,a series of single factor experiments on the depolymeriz...In this work,a novel alcohol alkali hydrolysis method was explored for the preparation of terephthalic acid(TPA)from waste polyethylene terephthalate(PET).First,a series of single factor experiments on the depolymerization rate of waste PET bottles and the yield of TPA were conducted to determine the optimized experimental conditions,in terms of reaction time,reaction temperature,dosage of ethylene glycol and sodium bicarbonate,amount of distilled water and stirring rate.Then IR spectra and elemental analysis were carried out for the characterization of obtained product.Under optimal experimental conditions,over 98%PET can be depolymerized into the target product(TPA)and the purity and yield of TPA are over 97%and 94%,respectively.Both the experimental and analytical results support a feasible process for the preparation of TPA from waste PET.It is expected that this alcohol alkali hydrolysis method can promise an effective way for the sustainable recycling of waste PET.展开更多
Silver ion can be useful in improving chalcopyrite bioleaching efficiency.In this work,leaching kinetics of this process was investigated using silver-bearing solid waste under different chalcopyrite/solid waste ratio...Silver ion can be useful in improving chalcopyrite bioleaching efficiency.In this work,leaching kinetics of this process was investigated using silver-bearing solid waste under different chalcopyrite/solid waste ratios.Bioleaching behavior indicates that silver-bearing solid waste can enhance the bioleaching process,and the redox potential is much higher than the proposed appropriate range(380−480 mV vs Ag/AgCl)with the solid waste added.There is a positive correlation between temperature and copper extraction rate.The kinetics data fit well with the shrinking-core model.Under these leaching conditions,the bioleaching of chalcopyrite is controlled by internal diffusion with calculated apparent activation energy(Ea)of 28.24 kJ/mol.This work is possible benificial to promote the industrial application of silver catalyst in leaching of chalcopyrite.展开更多
Proper solid waste disposal is an important socioeconomic concern for all developing countries.Municipalities have their own policies,individual approaches and methods to manage the solid wastes.They consider wastelan...Proper solid waste disposal is an important socioeconomic concern for all developing countries.Municipalities have their own policies,individual approaches and methods to manage the solid wastes.They consider wastelands outside the urban area as the best suitable for the solid waste disposal.Such improper site selection will create morphological changes that lead to environmental hazards in the urban and its surrounding areas.In this research,the site selection for urban solid waste disposal in the Coimbatore district used geographical information system(GIS)and multi-criteria decision analysis(MCDA).Thematic layers of lineament density,landuse/landcover,population density,groundwater depth,drainage density,slope,soil texture,geology and geomorphology were considered as primary criteria and weights for criteria,and sub-criteria were assigned by MCDA analysis.The resultant weight score was validated by consistency ratio so that the efficiency of the selected criteria was justified.The overlay analysis in GIS environment provides 17 potential zones in Coimbatore district,among which,four suitable sites were screened and refined with the help of field investigation and visual interpretation of satellite image.The result of landfill suitability map shows the effectiveness of the proposed method.展开更多
In the process of sulfuric acid production from pyrite, there is a lot of waste acid produced in fume washing with dilute acid. Acid recovery from this sort of waste sulfuric acid by diffusion dialysis is studied in t...In the process of sulfuric acid production from pyrite, there is a lot of waste acid produced in fume washing with dilute acid. Acid recovery from this sort of waste sulfuric acid by diffusion dialysis is studied in the paper. The mass transfer dialysis coefficient of sulfuric acid of the membrane AFX is measured, the effect of the flowrate of the feed and ratio of feed to water is investigated, and the two kinds of membrane (AFX and S203) are compared. The results show that diffusion dialysis process can separate the metal cation from sulfuric acid effectively, but it is difficult to separate non cation impurities as As - and F -. The contrast tests of the two membranes show that the dialysis mass transfer coefficient of the membrane AFX is larger, while capacity of the removing impurities of membrane S203 is somewhat better.展开更多
This study aims to reveal the macroscopic permanent deformation(PD)behavior and the internal structural evolution of construction and demolition waste(CDW)under loading.Firstly,the initial matric suction of CDW was me...This study aims to reveal the macroscopic permanent deformation(PD)behavior and the internal structural evolution of construction and demolition waste(CDW)under loading.Firstly,the initial matric suction of CDW was measured by the filter paper method.Secondly,the PD of CDW with different humidity and stress states was investigated by repeated load triaxial tests,and a comprehensive prediction model was established.Finally,the discrete element method was performed to analyze the internal structural evolution of CDW during deformation.These results showed that the VAN-GENUCHTEN model could describe the soil-water characteristic curve of CDW well.The PD increases with the increase of the deviator stress and the number of cyclic loading,but the opposite trend was observed when the initial matric suction and confining pressure increased.The proposed model in this study provides a satisfactory prediction of PD.The discrete element method could accurately simulate the macroscopic PD of CDW,and the shear force,interlock force and sliding content increase with the increase of deviator stress during the deformation.The research could provide useful reference for the deformation stability analysis of CDW under cyclic loading.展开更多
To analyze the feasibility of utilization of thermal technology in fly ash treatment, thermal properties and microstructures of municipal solid waste incineration （MSW1） fly ash were studied by measuring the chemica...To analyze the feasibility of utilization of thermal technology in fly ash treatment, thermal properties and microstructures of municipal solid waste incineration （MSW1） fly ash were studied by measuring the chemical element composition, specific surface area, pore sizes, functional groups, TEM image, mineralogy and DSC-TG curves of raw and sintered fly ash specimens. The results show that MSWI fly ash particles mostly have irregular shapes and non-typical pore structure, and the supersonic treatment improves the pore structure; MSWI fly ash consists of Such crystals as SiO2, CaSO4 and silica-aluminates, and some soluble salts like KCl and NaCl. During the sintering process, mineralogy changes largely and novel solid solutions are produced gradually with the rise of temperature. Therefore, the utilization of a proper thermal technology not only destructs those persistent organic toxicants but also stabilizes hazardous heavy metals in MSWI fly ash.展开更多
Grate fly ash and fluidized bed fly ash mixed with glass cullet additive respectively were melted in the electronic arc-furnace. The product, arc-melting slag, was further treated by crushing, pressing and heat treatm...Grate fly ash and fluidized bed fly ash mixed with glass cullet additive respectively were melted in the electronic arc-furnace. The product, arc-melting slag, was further treated by crushing, pressing and heat treatment in order to make the glass-ceramics. The crystallization behaviors of the produced glass-ceramics were examined by differential thermal analysis （DTA）, X-ray diffractometry （XRD） and scanning electron microscopy （SEM）. Results show that main crystalline phase of the glass-ceramics fi＇om grate fly ash is wollastonite （CaSiO3） with small amount of diopside （Ca（Mg,Al）（Si,Al）206）, and that from fluidized bed fly ash is diopside （Ca（Mg,Al）（Si,Al）206）. It is found that the glass-ceramics sintered at 850 ℃and 1 000℃ from grate fly ash and fluidized bed fly ash respectively have the optimal physical, mechanical and chemical characteristics. Glass-ceramics samples, produced from incinerator fly ash with desirable properties and the low leaching concentration of heavy metals, can be the substitute of nature materials such as marble, granite and porcelain tiles.展开更多
In the present work, the gas flow pressure drop and gas–solid heat transfer characteristics in sinter bed layer of vertical tank were studied experimentally on the basis of the homemade experimental setup. The gas fl...In the present work, the gas flow pressure drop and gas–solid heat transfer characteristics in sinter bed layer of vertical tank were studied experimentally on the basis of the homemade experimental setup. The gas flow pressure drop through the sinter bed layer was measured with different gas velocity and particle diameters, as well as the sinter and air temperatures. The influences of gas superficial velocity and particle diameter on the gas flow pressure drop and gas solid heat transfer in sinter bed layer were analyzed in detail. The revised Ergun's correlation and gas solid heat transfer correlation were obtained according to the regression analysis of experimental data. It is found that, the pressure drop of unit bed layer height gradually increases as a quadratic relationship with increasing the gas superficial velocity, and decreases as an exponential relationship with the increase of sinter particle diameter. For a given sinter temperature, the heat transfer coefficient in sinter bed layer increases with increasing the gas superficial velocity, and increases with decreasing the sinter particle diameter. In addition, the heat transfer coefficient also gradually increases with increasing the sinter temperature at the same gas superficial velocity and sinter particle diameter. The mean deviations between the experimental data obtained from this work and the values calculated by the revised Ergun's correlation and the experimental heat transfer correlation are 7.22% and 4.22% respectively, showing good prediction.展开更多
To recover metal from copper slags,a new process involving two steps of oxidative desulfurization followed by smelting reduction was proposed in which one hazardous waste(waste cathode carbon)was used to treat another...To recover metal from copper slags,a new process involving two steps of oxidative desulfurization followed by smelting reduction was proposed in which one hazardous waste(waste cathode carbon)was used to treat another(copper slags).The waste cathode carbon is used not only as a reducing agent but also as a fluxing agent to decrease slag melting point.Upon holding for 60 min in air atmosphere first and then smelting with 14.4 wt%waste cathode carbon and 25 wt%CaO for 180 min in high purity Ar atmosphere at 1450℃,the recovery rates of Cu and Fe reach 95.89%and 94.64%,respectively,and meanwhile greater than 90%of the fluoride from waste cathode carbon is transferred into the final slag as CaF_(2) and Ca_(2)Si_(2)F_(2)O_(7),which makes the content of soluble F in the slag meet the national emission standard.Besides,the sulphur content in the obtained Fe-Cu alloy is low to 0.03 wt%.展开更多
A novel low-temperature alkaline smelting process is proposed to convert and separate amphoteric metals in crushed metal enrichment originated from waste printed circuit boards. The central composite design was used t...A novel low-temperature alkaline smelting process is proposed to convert and separate amphoteric metals in crushed metal enrichment originated from waste printed circuit boards. The central composite design was used to optimize the operating parameters,in which mass ratio of Na OH-to-CME, smelting temperature and smelting time were chosen as the variables, and the conversions of amphoteric metals tin, lead, aluminum and zinc were response parameters. Second-order polynomial models of high significance and3 D response surface plots were constructed to show the relationship between the responses and the variables. Optimum area of80%-85% Pb conversion and over 95% Sn conversion was obtained by the overlaid contours at mass ratio of Na OH-to-CME of4.5-5.0, smelting temperature of 653-723 K, smelting time of 90-120 min. The models were validated experimentally in the optimum area, and the results demonstrate that these models are reliable and accurate in predicting the smelting process.展开更多
Thermal decomposition of waste epoxy PCBs was performed in different atmospheres （nitrogen, argon, air and vacuum） at a heating rate of 10 ℃/rain by DSC-TGA, and the pyrolysis characteristic was analyzed. The gases...Thermal decomposition of waste epoxy PCBs was performed in different atmospheres （nitrogen, argon, air and vacuum） at a heating rate of 10 ℃/rain by DSC-TGA, and the pyrolysis characteristic was analyzed. The gases volatilized from the experiment were qualitatively analyzed by TG-FTIR. Kinetics study shows that pyrolysis reaction takes place between 300 and 400℃, and the activation energies are 256, 212 and 186.2 kJ/mol in nitrogen, argon and vacuum, respectively. There are two mass-loss processes in the decomposition under air atmosphere. In the first mass-loss process, the decomposition is the main reaction, and in the second process, the oxidation is the main reaction. The activation energy of the second mass-loss process is 99.6 kJ/mol by isothermal heat-treatments. TG-FTIR analysis shows carbon dioxide, carbon monoxide, hydrogen bromide, phenol and substituent phenol are given off during the pyrolysis of waste epoxy PCBs.展开更多
Anaerobic co-digestion of food waste（FW） and rice straw（RS） in continuously stirred tank reactor（CSTR） at high organic loading rate（OLR） was investigated. Co-digestion studies of FW and RS with six different m...Anaerobic co-digestion of food waste（FW） and rice straw（RS） in continuously stirred tank reactor（CSTR） at high organic loading rate（OLR） was investigated. Co-digestion studies of FW and RS with six different mixing ratios were conducted at an initial volatile solid（VS） concentration of more than 3 g VS · L-1. The biogas production, methane contents, degradation efficiency of VS, chemical oxygen demand（COD） and volatile fatty acids（VFAs） were determined to evaluate the stability and performance of the system. The results showed that the co-digestion process had higher system stability and higher volumetric biogas production than mono-digestions. Increase in FW content in the feedstock could increase the methane yield and shorten retention time. The efficiency of co-digestion systems mainly relied on the mixing ratios of FW and RS to some extent. The highest methane yield was 60.55 m L· g V· S-1 · d-1 at a mass ratio（FW/RS） of 3 ： 1, which was 178% and 70% higher than that of mono-digestions of FW and RS, respectively. Consequently, the anaerobic co-digestion of FW and RS could have superior stability and better performance than monodigestions in higher organic loading system.展开更多
基金supported by the National Natural Science Foundation of China(22168032)the National Key Research and Development Program of China(2023YFC3904302,2023YFB4103500)the Key Projects of Ning Dong Energy and Chemical Industry Base(2023NDKJXMLX022).
文摘A new adsorbent was successfully prepared by hydrothermal treatment and chemical activation through coal gasification fine slag(CGFS)and blue algae(BA)as raw materials and used for CO_(2)capture.The CO_(2)chemisorption capacity of the adsorbent was further enhanced by taking advantage of the nitrogenous bases contained in the BA.In the hydrothermal process,the addition of BA significantly increased the content of pyrrole nitrogen in the adsorbent.In the activation process,pyrrole nitrogen gradually changed into pyridine nitrogen and graphite nitrogen.Increased BA addition result in a higher specific surface area and microporosity of the adsorbent.The CO_(2)adsorption performance test proved that the CGFS-50%-CA sample has the strongest CO_(2)adsorption capacity at low temperature,up to 15.59 cm^(3)/g,which is mainly through physical adsorption,and the CGFS-10%-CA sample has the strongest CO_(2)adsorption capacity at high temperature,up to 7.31 cm^(3)/g,which is mainly through chemical adsorption.CO_(2)uptake of the CGFS-10%-CA sample was well maintained after 10 cycles,with regeneration efficiencies above 99%.The results indicate that the novel adsorbents with coexistence of physical and chemical adsorption have great potential for CO_(2)adsorption applications.
文摘The use of carbon from waste biomass has the potential to eliminate the drawbacks of Li-S batteries and improve their overall performance.Chrome-tanned-leather-shavings(CTLS)are a readily available waste product that can be transformed into porous carbon.We prepared an ac-tivated carbon by microwave pyrolysis combined with KOH activator using the CTLS as starting materials.The carbon had a specific surface area of 556 m^(2)g^(-1) and a honeycomb-like structure.Two kinds of N-doped activated carbons were then synthesized by thermal decomposition of the activated carbon,either combined with urea,or impregnated with eth-anolamine.Both N-doped activated carbons have an in-creased number of nitrogen and amine surface groups.However,only the urea treatment was effective in improv-ing the initial capacity of the cell(1363 mAh g^(-1)),which is probably linked to the sorption of long-chain polysulfides.This investigation confirms that it is possible to use the thermal de-composition of urea to obtain carbon materials from CTLS for use as the sulfur-host cathode in Li-S batteries and improve their performance.A radial basis function neural network was fitted to provide statistical support for the experimental results,which confirmed the importance of the nitrogen content of the carbons in determining the discharge capacity of the cells.
基金Project(2024JJ2074) supported by the Natural Science Foundation of Hunan Province,ChinaProject(22376221) supported by the National Natural Science Foundation of ChinaProject(2023QNRC001) supported by the Young Elite Scientists Sponsorship Program by CAST,China。
文摘Driven by rapid technological advancements and economic growth,mineral extraction and metal refining have increased dramatically,generating huge volumes of tailings and mine waste(TMWs).Investigating the morphological fractions of heavy metals and metalloids(HMMs)in TMWs is key to evaluating their leaching potential into the environment;however,traditional experiments are time-consuming and labor-intensive.In this study,10 machine learning(ML)algorithms were used and compared for rapidly predicting the morphological fractions of HMMs in TMWs.A dataset comprising 2376 data points was used,with mineral composition,elemental properties,and total concentration used as inputs and concentration of morphological fraction used as output.After grid search optimization,the extra tree model performed the best,achieving coefficient of determination(R2)of 0.946 and 0.942 on the validation and test sets,respectively.Electronegativity was found to have the greatest impact on the morphological fraction.The models’performance was enhanced by applying an ensemble method to the top three optimal ML models,including gradient boosting decision tree,extra trees and categorical boosting.Overall,the proposed framework can accurately predict the concentrations of different morphological fractions of HMMs in TMWs.This approach can minimize detection time,aid in the safe management and recovery of TMWs.
文摘China has a large solid waste stockpile and a low resource utilisation rate,and the utilisation of solid waste resources is of great significance in promoting sustainable social development.In order to further promote the green and efficient development of China's road field,an overview of the current status of the application,research progress,hot frontiers,problems and their countermeasures based on the three aspects of industrial solid wastes,engineering solid wastes and municipal solid wastes in highway engineering was conducted,and the development prospect of the resourceful utilisation of solid waste in highway engineering was outlooked,with a view to promoting the development of China's green roads.Statistics on the stockpile,utilisation and comprehensive utilisation rate of industrial solid wastes in China are presented,and the optimal mixing amount,production process and application technology of industrial solid wastes for road base materials are systematically summarised.Based on the concept of high-value utilisation of solid waste,the mechanical properties,durability,construction technology and quality control standards of engineering solid waste applied in roadbed engineering are summarised,and the difficulties in the application of engineering solid waste in road engineering are summarised.Finally,the feasibility,mechanical properties and environmental characteristics of municipal solid waste domestic waste incinerator slag,waste tyres and plastics applied in road engineering are summarised.This review can provide references and lessons for the design and development of green roads,and promote the innovation and development of greening road engineering.
基金Projects(51108100,50808184)supported by the National Natural Science Foundation of ChinaProject(100Z007)supported by the Ministry of Education of China+1 种基金Project(200103YB020)supported by Foundation of Guangxi Educational Committee,ChinaProject supported by Guangxi Normal University Education Development Foundation for Young Scholars,China
文摘The mechanism of removing phosphate by MSWI(municipal solid waste incineration)fly ash was investigated by SEM(scanning electron microscopy)with EDS(energy dispersion spectrum),XRD(X-ray diffraction),FT-IR(Fourier transform infrared spectroscopy),BET(specific surface area),and BJH(pore size distribution).The results indicate that the removal rate of phosphate(100 mg/L)in 50 mL phosphorus wastewater reaches at 99.9% as the dosage of MSWI fly ash being 0.9000 g under room temperature.The specific surface area of MSWI fly ash is less than 6.1 m2/g and the total pore volume is below 0.021 cm3/g,suggesting that the absorption capacity of calcite is too weak to play an important role in phosphate removal.SEM images show that drastic changes had taken place on its specific surface shape after reaction,and EDS tests indicate that some phosphate precipitates are formed and attached onto MSWI fly ash particles.Chemical precipitation is the main manner of phosphate removal and the main reaction is: 3Ca2++2 PO4 3-+xH2O→Ca3(PO4)2↓·xH2O.Besides,XRD tests show that the composition of MSWI fly ash is complex,but CaSO4 is likely to be the main source of Ca2+.The soluble heavy metals in MSWI fly ash are stabilized by phosphate.
文摘Integrating disaster waste issue is a critical component of making humanitarian action fit for the future,anticipating global risks and challenges such as increased vulnerability due to climate change and environmental degradation.This requires a fundamental shift towards a model that not only strengthens the response to crises but also learns and adapts in order to anticipate and act before such waste garnered.This article conducted analyses on the characteristics of disasters in the past two decades.Uncertainties confound disaster waste management,including the timing and magnitude of each disaster,and the amounts and types of waste that will be generated.For these reasons alone,disaster waste management must be an integral part of development planning and processes.Making 10 years since the 2008 Wenchuan earthquake,this article highlights that disaster waste management is not only debris clearance or waste management following a disaster,but also includes prevention and pre-disaster preparedness aspects in terms of enhancing resilience of local communities.Such"mainstreaming,"ensures that disaster waste management(DWM)will be treated as a priority issue,on an ongoing basis.Based on UN Environment's experiences and approaches,this paper emphasises that preparedness is the key,and that priority should be accorded to integrating disaster contingency planning in national and city level waste management strategies as well as mainstreaming waste management issues within broader disaster preparedness and response plans and actions.It is envisaged that the issues presented and the gaps identified in this paper will provide a basis for future comprehensive and cohesive research on disaster waste management.In turn,this research can lead to better preparedness and response on disaster waste management.
文摘The micro-nuclei and abnormal nuclei rates of peacock fish are tested,genetic toxic effects of rare-earth waste and its products(cement,plastic) on peacock in water are investigated.Results show that the leachate of rare-earth waste can lead to micronuclei and abnormal nuclei rates of peacock fish an obvious increase(P<0.01). Products made of the waste cause the micronuclei rate to be increased because of its low radio active action,but the change in abnormal nuclei rate can't reach a remarkable level.It shows that rare-earth waste has a certain effect of causing mutation on aquatic organism.Harmfulness of products made from this waste is decreased largely,and resources can be effectively saved.
基金Projects(41877551,41842020)supported by the National Natural Science Foundation of ChinaProject(201509048)supported by the Environmental Protection’s Special Scientific Research for Chinese Public Welfare Industry
文摘Bauxite residue is a highly alkaline material generated from the production of alumina in which bauxite is dissolved in caustic soda.Approximately 4.4 billion tons of bauxite residues are either stockpiled or landfilled,creating environmental risks either from the generation of dust or migration of filtrates.High alkalinity is the critical factor restricting complete utilization of bauxite residues,whilst the application of alkaline regulation agents is costly and difficult to apply widely.For now,current industrial wastes,such as waste acid,ammonia nitrogen wastewater,waste gypsum and biomass,have become major problems restricting the development of the social economy.Regulation of bauxite residues alkalinity by industrial waste was proposed to achieve‘waste control by waste’with good economic and ecological benefits.This review will focus on the origin and transformation of alkalinity in bauxite residues using typical industrial waste.It will propose key research directions with an emphasis on alkaline regulation by industrial waste,whilst also providing a scientific reference point for their potential use as amendments to enhance soil formation and establish vegetation on bauxite residue disposal areas(BRDAs)following large-scale disposal.
基金Project(2016TP1007)supported by the Hunan Provincial Science and Technology Plan,China
文摘In this work,a novel alcohol alkali hydrolysis method was explored for the preparation of terephthalic acid(TPA)from waste polyethylene terephthalate(PET).First,a series of single factor experiments on the depolymerization rate of waste PET bottles and the yield of TPA were conducted to determine the optimized experimental conditions,in terms of reaction time,reaction temperature,dosage of ethylene glycol and sodium bicarbonate,amount of distilled water and stirring rate.Then IR spectra and elemental analysis were carried out for the characterization of obtained product.Under optimal experimental conditions,over 98%PET can be depolymerized into the target product(TPA)and the purity and yield of TPA are over 97%and 94%,respectively.Both the experimental and analytical results support a feasible process for the preparation of TPA from waste PET.It is expected that this alcohol alkali hydrolysis method can promise an effective way for the sustainable recycling of waste PET.
基金Project(2018JJ1041)supported by the Natural Science Foundation of Hunan,ChinaProjects(51774332,U1932129,51804350 and 51934009)supported by the National Natural Science Foundation of China。
文摘Silver ion can be useful in improving chalcopyrite bioleaching efficiency.In this work,leaching kinetics of this process was investigated using silver-bearing solid waste under different chalcopyrite/solid waste ratios.Bioleaching behavior indicates that silver-bearing solid waste can enhance the bioleaching process,and the redox potential is much higher than the proposed appropriate range(380−480 mV vs Ag/AgCl)with the solid waste added.There is a positive correlation between temperature and copper extraction rate.The kinetics data fit well with the shrinking-core model.Under these leaching conditions,the bioleaching of chalcopyrite is controlled by internal diffusion with calculated apparent activation energy(Ea)of 28.24 kJ/mol.This work is possible benificial to promote the industrial application of silver catalyst in leaching of chalcopyrite.
文摘Proper solid waste disposal is an important socioeconomic concern for all developing countries.Municipalities have their own policies,individual approaches and methods to manage the solid wastes.They consider wastelands outside the urban area as the best suitable for the solid waste disposal.Such improper site selection will create morphological changes that lead to environmental hazards in the urban and its surrounding areas.In this research,the site selection for urban solid waste disposal in the Coimbatore district used geographical information system(GIS)and multi-criteria decision analysis(MCDA).Thematic layers of lineament density,landuse/landcover,population density,groundwater depth,drainage density,slope,soil texture,geology and geomorphology were considered as primary criteria and weights for criteria,and sub-criteria were assigned by MCDA analysis.The resultant weight score was validated by consistency ratio so that the efficiency of the selected criteria was justified.The overlay analysis in GIS environment provides 17 potential zones in Coimbatore district,among which,four suitable sites were screened and refined with the help of field investigation and visual interpretation of satellite image.The result of landfill suitability map shows the effectiveness of the proposed method.
文摘In the process of sulfuric acid production from pyrite, there is a lot of waste acid produced in fume washing with dilute acid. Acid recovery from this sort of waste sulfuric acid by diffusion dialysis is studied in the paper. The mass transfer dialysis coefficient of sulfuric acid of the membrane AFX is measured, the effect of the flowrate of the feed and ratio of feed to water is investigated, and the two kinds of membrane (AFX and S203) are compared. The results show that diffusion dialysis process can separate the metal cation from sulfuric acid effectively, but it is difficult to separate non cation impurities as As - and F -. The contrast tests of the two membranes show that the dialysis mass transfer coefficient of the membrane AFX is larger, while capacity of the removing impurities of membrane S203 is somewhat better.
基金Project(52025085)supported by the National Science Fund for Distinguished Young Scholars,ChinaProjects(51927814,51878078)supported by the National Natural Science Foundation of China+3 种基金Project(2018-025)supported by the Training Program for High-level Technical Personnel in Transportation Industry,ChinaProject(CTKY-PTRC 2018-003)supported by the Design Theory,Method and Demonstration of Durability Asphalt Pavement Based on Heavy-duty Traffic Conditions in Shanghai Area,ChinaProject(2020RC4048)supported by the Science and Technology Innovation Program of Hunan Province,ChinaProject(SJCX202001)supported by the Construction Project for Graduate Students of Changsha University of Science&Technology,China。
文摘This study aims to reveal the macroscopic permanent deformation(PD)behavior and the internal structural evolution of construction and demolition waste(CDW)under loading.Firstly,the initial matric suction of CDW was measured by the filter paper method.Secondly,the PD of CDW with different humidity and stress states was investigated by repeated load triaxial tests,and a comprehensive prediction model was established.Finally,the discrete element method was performed to analyze the internal structural evolution of CDW during deformation.These results showed that the VAN-GENUCHTEN model could describe the soil-water characteristic curve of CDW well.The PD increases with the increase of the deviator stress and the number of cyclic loading,but the opposite trend was observed when the initial matric suction and confining pressure increased.The proposed model in this study provides a satisfactory prediction of PD.The discrete element method could accurately simulate the macroscopic PD of CDW,and the shear force,interlock force and sliding content increase with the increase of deviator stress during the deformation.The research could provide useful reference for the deformation stability analysis of CDW under cyclic loading.
基金Project(50808184) supported by the National Natural Science Foundation of China
文摘To analyze the feasibility of utilization of thermal technology in fly ash treatment, thermal properties and microstructures of municipal solid waste incineration （MSW1） fly ash were studied by measuring the chemical element composition, specific surface area, pore sizes, functional groups, TEM image, mineralogy and DSC-TG curves of raw and sintered fly ash specimens. The results show that MSWI fly ash particles mostly have irregular shapes and non-typical pore structure, and the supersonic treatment improves the pore structure; MSWI fly ash consists of Such crystals as SiO2, CaSO4 and silica-aluminates, and some soluble salts like KCl and NaCl. During the sintering process, mineralogy changes largely and novel solid solutions are produced gradually with the rise of temperature. Therefore, the utilization of a proper thermal technology not only destructs those persistent organic toxicants but also stabilizes hazardous heavy metals in MSWI fly ash.
基金Project(20806051) supported by the National Natural Science Foundation of ChinaProject(20080440680) supported by China Postdoctoral Science Foundation
文摘Grate fly ash and fluidized bed fly ash mixed with glass cullet additive respectively were melted in the electronic arc-furnace. The product, arc-melting slag, was further treated by crushing, pressing and heat treatment in order to make the glass-ceramics. The crystallization behaviors of the produced glass-ceramics were examined by differential thermal analysis （DTA）, X-ray diffractometry （XRD） and scanning electron microscopy （SEM）. Results show that main crystalline phase of the glass-ceramics fi＇om grate fly ash is wollastonite （CaSiO3） with small amount of diopside （Ca（Mg,Al）（Si,Al）206）, and that from fluidized bed fly ash is diopside （Ca（Mg,Al）（Si,Al）206）. It is found that the glass-ceramics sintered at 850 ℃and 1 000℃ from grate fly ash and fluidized bed fly ash respectively have the optimal physical, mechanical and chemical characteristics. Glass-ceramics samples, produced from incinerator fly ash with desirable properties and the low leaching concentration of heavy metals, can be the substitute of nature materials such as marble, granite and porcelain tiles.
基金Project(51274065)supported by the National Natural Science Foundation of ChinaProject(2015020074)supported by the Science and Technology Planning Project of Liaoning Province,China
文摘In the present work, the gas flow pressure drop and gas–solid heat transfer characteristics in sinter bed layer of vertical tank were studied experimentally on the basis of the homemade experimental setup. The gas flow pressure drop through the sinter bed layer was measured with different gas velocity and particle diameters, as well as the sinter and air temperatures. The influences of gas superficial velocity and particle diameter on the gas flow pressure drop and gas solid heat transfer in sinter bed layer were analyzed in detail. The revised Ergun's correlation and gas solid heat transfer correlation were obtained according to the regression analysis of experimental data. It is found that, the pressure drop of unit bed layer height gradually increases as a quadratic relationship with increasing the gas superficial velocity, and decreases as an exponential relationship with the increase of sinter particle diameter. For a given sinter temperature, the heat transfer coefficient in sinter bed layer increases with increasing the gas superficial velocity, and increases with decreasing the sinter particle diameter. In addition, the heat transfer coefficient also gradually increases with increasing the sinter temperature at the same gas superficial velocity and sinter particle diameter. The mean deviations between the experimental data obtained from this work and the values calculated by the revised Ergun's correlation and the experimental heat transfer correlation are 7.22% and 4.22% respectively, showing good prediction.
基金Project(U1602272)supported by the National Natural Science Foundation of China。
文摘To recover metal from copper slags,a new process involving two steps of oxidative desulfurization followed by smelting reduction was proposed in which one hazardous waste(waste cathode carbon)was used to treat another(copper slags).The waste cathode carbon is used not only as a reducing agent but also as a fluxing agent to decrease slag melting point.Upon holding for 60 min in air atmosphere first and then smelting with 14.4 wt%waste cathode carbon and 25 wt%CaO for 180 min in high purity Ar atmosphere at 1450℃,the recovery rates of Cu and Fe reach 95.89%and 94.64%,respectively,and meanwhile greater than 90%of the fluoride from waste cathode carbon is transferred into the final slag as CaF_(2) and Ca_(2)Si_(2)F_(2)O_(7),which makes the content of soluble F in the slag meet the national emission standard.Besides,the sulphur content in the obtained Fe-Cu alloy is low to 0.03 wt%.
基金Projects(51074190,51234009)supported by the National Natural Science Foundation of ChinaProject(2014DFA90520)supported by International Cooperation Program of Ministry of Science of ChinaProject(20110162110049)supported by the Doctoral Scientific Fund Project of the Ministry of Education of China
文摘A novel low-temperature alkaline smelting process is proposed to convert and separate amphoteric metals in crushed metal enrichment originated from waste printed circuit boards. The central composite design was used to optimize the operating parameters,in which mass ratio of Na OH-to-CME, smelting temperature and smelting time were chosen as the variables, and the conversions of amphoteric metals tin, lead, aluminum and zinc were response parameters. Second-order polynomial models of high significance and3 D response surface plots were constructed to show the relationship between the responses and the variables. Optimum area of80%-85% Pb conversion and over 95% Sn conversion was obtained by the overlaid contours at mass ratio of Na OH-to-CME of4.5-5.0, smelting temperature of 653-723 K, smelting time of 90-120 min. The models were validated experimentally in the optimum area, and the results demonstrate that these models are reliable and accurate in predicting the smelting process.
基金Project(2006AA06Z375) supported by the National High-tech Research and Development Program of China
文摘Thermal decomposition of waste epoxy PCBs was performed in different atmospheres （nitrogen, argon, air and vacuum） at a heating rate of 10 ℃/rain by DSC-TGA, and the pyrolysis characteristic was analyzed. The gases volatilized from the experiment were qualitatively analyzed by TG-FTIR. Kinetics study shows that pyrolysis reaction takes place between 300 and 400℃, and the activation energies are 256, 212 and 186.2 kJ/mol in nitrogen, argon and vacuum, respectively. There are two mass-loss processes in the decomposition under air atmosphere. In the first mass-loss process, the decomposition is the main reaction, and in the second process, the oxidation is the main reaction. The activation energy of the second mass-loss process is 99.6 kJ/mol by isothermal heat-treatments. TG-FTIR analysis shows carbon dioxide, carbon monoxide, hydrogen bromide, phenol and substituent phenol are given off during the pyrolysis of waste epoxy PCBs.
基金Supported by the Natural Science Foundation of Heilongjiang Province(QC2014C031)Returned Overseas Foundation of Heilongjiang Province(LC2013C07)+2 种基金Outstanding Academic Leaders Foundation of Harbin City(2013RFXYJ015)Young Reserve Talent Foundation of Harbin City(2014RFQYJ141)Outstanding Young Foundation of Heilongjiang Academy of Agricultural Sciences(2013JCQN003)
文摘Anaerobic co-digestion of food waste（FW） and rice straw（RS） in continuously stirred tank reactor（CSTR） at high organic loading rate（OLR） was investigated. Co-digestion studies of FW and RS with six different mixing ratios were conducted at an initial volatile solid（VS） concentration of more than 3 g VS · L-1. The biogas production, methane contents, degradation efficiency of VS, chemical oxygen demand（COD） and volatile fatty acids（VFAs） were determined to evaluate the stability and performance of the system. The results showed that the co-digestion process had higher system stability and higher volumetric biogas production than mono-digestions. Increase in FW content in the feedstock could increase the methane yield and shorten retention time. The efficiency of co-digestion systems mainly relied on the mixing ratios of FW and RS to some extent. The highest methane yield was 60.55 m L· g V· S-1 · d-1 at a mass ratio（FW/RS） of 3 ： 1, which was 178% and 70% higher than that of mono-digestions of FW and RS, respectively. Consequently, the anaerobic co-digestion of FW and RS could have superior stability and better performance than monodigestions in higher organic loading system.
