The rheological properties of two kinds of oil-based drilling fluids with typically composition were studied at pressures up to 138 MPa and temperatures up to 204 ℃ using the RheoChan 7400 Rheometer.The experimental ...The rheological properties of two kinds of oil-based drilling fluids with typically composition were studied at pressures up to 138 MPa and temperatures up to 204 ℃ using the RheoChan 7400 Rheometer.The experimental results show that the apparent viscosity,plastic viscosity and yield point decrease with the increase of temperature,and increase with the increase of pressure.The effect of pressure on the apparent viscosity,plastic viscosity and yield point is considerable at ambient temperature.However,this effect gradually reduces with the increase of temperature.The major factor influencing the rheological properties of oil-based drilling fluids is temperature instead of pressure in the deep sections of oil wells.On the basis of numerous experiments,the model for predict the apparent viscosity,plastic viscosity and yield point of oil-based drilling fluids at high temperature and pressure was established using the method of regressive analysis.It is confirmed that the calculated data are in good agreement with the measured data,and the correlation coefficients are more than 0.98.The model is convenient for use and suitable for the application in drilling operations.展开更多
A regrown composite fiber was synthesized during the sintering of diamond under high pressure 5.8 GPa and high temperature 1500℃for 1 min,using 3wt%MWCNTs as additive.SEM observation of the fiber after alkali and aci...A regrown composite fiber was synthesized during the sintering of diamond under high pressure 5.8 GPa and high temperature 1500℃for 1 min,using 3wt%MWCNTs as additive.SEM observation of the fiber after alkali and acid treatment revealed that the outer layer of the fiber is composed of nano-polycrystalline diamond.EDS,XPS,XRD and Raman spectrum analysis further identified that the fiber is composed of MWCNTs in the inner part and nano-polycrystalline diamond in the out layer.It is proposed that the untransformed MWCNTs may act as a template for the regrown outer layer of nano diamond fiber under high pressure and high temperature.展开更多
Cubic boron nitride(CBN) composites starting with CBN-Al mixtures were sintered on WC-16 wt%Co substrate under static high pressure of 5.0 GPa at temperatures of 800 to 1 400℃for 30 min.Vickers hardness of the sinter...Cubic boron nitride(CBN) composites starting with CBN-Al mixtures were sintered on WC-16 wt%Co substrate under static high pressure of 5.0 GPa at temperatures of 800 to 1 400℃for 30 min.Vickers hardness of the sintered samples increased with increasing CBN content and the highest hardness of 32.7 GPa was achieved for the CBN-5 wt%Al specimens sintered at 1 400℃.The reactions between CBN and Al started to occur at about 900℃and the reaction products strongly depended on the Al content,sintering temperature and Co diffused from the substrates according to the x-ray diffraction(XRD) observations.The CBN composite sintered at 1 200℃from a CBN-15 wt%Al mixture showed the best cutting performance.展开更多
Experimental and theoretical researches on the doping effect of interface binding state with homologous and heterogeneous dopants(d) in the system of PCD etc,as well as the action of intermediate layers between D /d a...Experimental and theoretical researches on the doping effect of interface binding state with homologous and heterogeneous dopants(d) in the system of PCD etc,as well as the action of intermediate layers between D /d at superhigh pressure and high temperature(HP-HT) are reported in this paper.展开更多
The experimental study of ultra-wideband (UWB) technology, its generation and on-line measurement are presented. An experimental repetitive UWB system is designed, manufactured, and tested. High-pressure spark gap swi...The experimental study of ultra-wideband (UWB) technology, its generation and on-line measurement are presented. An experimental repetitive UWB system is designed, manufactured, and tested. High-pressure spark gap switch and its components, as well as oil spark gap switch are studied experimentally on the system. Experimental results indicate that the system operates at a 200 pps repetitive rate with a stable performance. 100 MW peak power UWB pulses are obtained on the system. Fast-time response capacitive divider is designed and fabricated, allowing for an accurate measurement of the high power UWB signal. The main issues related to the design of the switch and the UWB signal online measurement are discussed.展开更多
The virial equation can well describe gas state at high temperature and pressure, but the difficulties in virial coefficient calculation limit the use of virial equation. Simple extended corresponding state principle(...The virial equation can well describe gas state at high temperature and pressure, but the difficulties in virial coefficient calculation limit the use of virial equation. Simple extended corresponding state principle(SE-CSP) is introduced in virial equation. Based on a corresponding state equation, including three characteristic parameters, an extended parameter is introduced to describe the second virial coefficient expressions of main products of propellant gas. The modified SE-CSP second virial coefficient expression was extrapolated based on the virial coefficients experimental temperature, and the second virial coefficients obtained are in good agreement with the experimental data at a low temperature and the theoretical values at high temperature. The maximum pressure in the closed bomb test was calculated with modified SE-CSP virial coefficient expressions with the calculated error of less than 2%, and the error was smaller than the result calculated with the reported values under the same calculation conditions. The modified SE-CSP virial coefficient expression provides a convenient and efficient method for practical virial coefficient calculation without resorting to complicated molecular model design and integral calculation.展开更多
随着碳捕集、利用与封存(carbon capture,utilization and storage,CCUS)技术在油田的持续应用,CO_(2)腐蚀井下管柱现象引起高度重视,亟需适用于高CO_(2)分压环境下考虑腐蚀速率随时间变化影响的腐蚀速率模型。通过模拟温度80~120℃、CO...随着碳捕集、利用与封存(carbon capture,utilization and storage,CCUS)技术在油田的持续应用,CO_(2)腐蚀井下管柱现象引起高度重视,亟需适用于高CO_(2)分压环境下考虑腐蚀速率随时间变化影响的腐蚀速率模型。通过模拟温度80~120℃、CO_(2)分压15~30 MPa条件下Q125、3Cr和13Cr管材的腐蚀,建立了这3种管材考虑温度、CO_(2)分压和腐蚀时间影响的腐蚀速率预测模型,并对Q125套管进行了安全服役寿命预测。结果表明:同一CO_(2)分压下,Q125、3Cr管材腐蚀速率随温度增加呈先增后减的趋势,13Cr管材腐蚀速率随温度增加而增大;3种管材腐蚀速率均随CO_(2)分压增加而增大。Q125管材匀速和变速两种腐蚀速率模型均适用,3Cr和13Cr管材适用变速腐蚀模型。Q125套管的抗拉安全服役年限随着CO_(2)分压的增加而逐渐降低,抗拉安全服役年限最短约为12 a。展开更多
为了研究高温和应变率对超高性能混凝土(UHPC)劈裂抗拉性能的影响,对不同温度(20、105、200、300、400℃)作用后UHPC的质量损失率、抗压强度、弹性模量、静态和动态(应变率为1.8~6.8 s^(-1))劈裂抗拉强度进行了测试.结果表明:以2~10℃/...为了研究高温和应变率对超高性能混凝土(UHPC)劈裂抗拉性能的影响,对不同温度(20、105、200、300、400℃)作用后UHPC的质量损失率、抗压强度、弹性模量、静态和动态(应变率为1.8~6.8 s^(-1))劈裂抗拉强度进行了测试.结果表明:以2~10℃/min的加热速率升温至400℃后,所有试件均在保温期间发生爆裂性剥落;U H P C的抗压强度、弹性模量、静态劈裂抗拉强度均随温度增大而提高,300℃作用后比常温时分别提高了13.2%、19.1%和17.3%;动态劈裂抗拉强度和耗散能均具有明显的应变率效应,当应变率从1.8~2.2 s^(-1)增加到6.3~6.8 s^(-1)时,20~300℃作用后的UHPC动态劈裂抗拉强度和耗散能分别提高了69.1%~74.1%和146.7%~177.6%;高温作用后UHPC中C-S-H表面的吸附水、孔隙内自由水和凝胶结合水先后分解,增大了试件的质量损失率;基体内高温和高压环境促进了水泥水化反应和硅灰火山灰反应,提升了UHPC的致密程度,增强了钢纤维的桥连作用;在冲击荷载作用下,基体开裂速度的加快和由钢纤维拔出所致基体摩擦效应的增强导致耗散能增大.展开更多
基金Project(50574061) supported by the National Natural Science Foundation of ChinaProject(IRT0411) supported by the Changjiang Scholars and Innovative Research Team,Ministry of Education
文摘The rheological properties of two kinds of oil-based drilling fluids with typically composition were studied at pressures up to 138 MPa and temperatures up to 204 ℃ using the RheoChan 7400 Rheometer.The experimental results show that the apparent viscosity,plastic viscosity and yield point decrease with the increase of temperature,and increase with the increase of pressure.The effect of pressure on the apparent viscosity,plastic viscosity and yield point is considerable at ambient temperature.However,this effect gradually reduces with the increase of temperature.The major factor influencing the rheological properties of oil-based drilling fluids is temperature instead of pressure in the deep sections of oil wells.On the basis of numerous experiments,the model for predict the apparent viscosity,plastic viscosity and yield point of oil-based drilling fluids at high temperature and pressure was established using the method of regressive analysis.It is confirmed that the calculated data are in good agreement with the measured data,and the correlation coefficients are more than 0.98.The model is convenient for use and suitable for the application in drilling operations.
基金Supported by the National Natural Science Foundation of China(No.50342017)by the Natural Science Foundation of Beijing(No.2042019)
文摘A regrown composite fiber was synthesized during the sintering of diamond under high pressure 5.8 GPa and high temperature 1500℃for 1 min,using 3wt%MWCNTs as additive.SEM observation of the fiber after alkali and acid treatment revealed that the outer layer of the fiber is composed of nano-polycrystalline diamond.EDS,XPS,XRD and Raman spectrum analysis further identified that the fiber is composed of MWCNTs in the inner part and nano-polycrystalline diamond in the out layer.It is proposed that the untransformed MWCNTs may act as a template for the regrown outer layer of nano diamond fiber under high pressure and high temperature.
文摘Cubic boron nitride(CBN) composites starting with CBN-Al mixtures were sintered on WC-16 wt%Co substrate under static high pressure of 5.0 GPa at temperatures of 800 to 1 400℃for 30 min.Vickers hardness of the sintered samples increased with increasing CBN content and the highest hardness of 32.7 GPa was achieved for the CBN-5 wt%Al specimens sintered at 1 400℃.The reactions between CBN and Al started to occur at about 900℃and the reaction products strongly depended on the Al content,sintering temperature and Co diffused from the substrates according to the x-ray diffraction(XRD) observations.The CBN composite sintered at 1 200℃from a CBN-15 wt%Al mixture showed the best cutting performance.
文摘Experimental and theoretical researches on the doping effect of interface binding state with homologous and heterogeneous dopants(d) in the system of PCD etc,as well as the action of intermediate layers between D /d at superhigh pressure and high temperature(HP-HT) are reported in this paper.
文摘The experimental study of ultra-wideband (UWB) technology, its generation and on-line measurement are presented. An experimental repetitive UWB system is designed, manufactured, and tested. High-pressure spark gap switch and its components, as well as oil spark gap switch are studied experimentally on the system. Experimental results indicate that the system operates at a 200 pps repetitive rate with a stable performance. 100 MW peak power UWB pulses are obtained on the system. Fast-time response capacitive divider is designed and fabricated, allowing for an accurate measurement of the high power UWB signal. The main issues related to the design of the switch and the UWB signal online measurement are discussed.
文摘The virial equation can well describe gas state at high temperature and pressure, but the difficulties in virial coefficient calculation limit the use of virial equation. Simple extended corresponding state principle(SE-CSP) is introduced in virial equation. Based on a corresponding state equation, including three characteristic parameters, an extended parameter is introduced to describe the second virial coefficient expressions of main products of propellant gas. The modified SE-CSP second virial coefficient expression was extrapolated based on the virial coefficients experimental temperature, and the second virial coefficients obtained are in good agreement with the experimental data at a low temperature and the theoretical values at high temperature. The maximum pressure in the closed bomb test was calculated with modified SE-CSP virial coefficient expressions with the calculated error of less than 2%, and the error was smaller than the result calculated with the reported values under the same calculation conditions. The modified SE-CSP virial coefficient expression provides a convenient and efficient method for practical virial coefficient calculation without resorting to complicated molecular model design and integral calculation.
文摘为了研究高温和应变率对超高性能混凝土(UHPC)劈裂抗拉性能的影响,对不同温度(20、105、200、300、400℃)作用后UHPC的质量损失率、抗压强度、弹性模量、静态和动态(应变率为1.8~6.8 s^(-1))劈裂抗拉强度进行了测试.结果表明:以2~10℃/min的加热速率升温至400℃后,所有试件均在保温期间发生爆裂性剥落;U H P C的抗压强度、弹性模量、静态劈裂抗拉强度均随温度增大而提高,300℃作用后比常温时分别提高了13.2%、19.1%和17.3%;动态劈裂抗拉强度和耗散能均具有明显的应变率效应,当应变率从1.8~2.2 s^(-1)增加到6.3~6.8 s^(-1)时,20~300℃作用后的UHPC动态劈裂抗拉强度和耗散能分别提高了69.1%~74.1%和146.7%~177.6%;高温作用后UHPC中C-S-H表面的吸附水、孔隙内自由水和凝胶结合水先后分解,增大了试件的质量损失率;基体内高温和高压环境促进了水泥水化反应和硅灰火山灰反应,提升了UHPC的致密程度,增强了钢纤维的桥连作用;在冲击荷载作用下,基体开裂速度的加快和由钢纤维拔出所致基体摩擦效应的增强导致耗散能增大.
