Because of an unfortunate mistake by authors,the Project(5227010679)of Foundation item was wrong.The corrected Project is shown as follows:Project(52271073).
The process of preparing anodic oxide film containing active sites and electroless nickel plating on highly active rare earth magnesium alloy was developed.The formation mechanism of electroless nickel plating on acti...The process of preparing anodic oxide film containing active sites and electroless nickel plating on highly active rare earth magnesium alloy was developed.The formation mechanism of electroless nickel plating on active anodic oxide film and the structure and properties of the composite coating were studied by several surface and electrochemical techniques.The results showed that Ag nanograins with an average size of 10 nm were embedded into the anodic oxide film with pores of 0.1−2μm.Ag nanoparticles provided a catalytic site for the deposition of Ni-B alloy,and the Ni crystal nucleus was first grown in horizontal mode and then in cylindrical mode.The corrosion potential of the composite coating increased by 1.37 V and the corrosion current reduced two orders of magnitude due to the subsequent deposition of Ni-P alloy.The high corrosion resistance was attributed to the misaligning of these micro defects in the three different layers and the amorphous structure of the Ni-P alloy in the outer layer.These findings provide a new idea for electroless nickel plating on anodic oxide film.展开更多
An effective hybrid optimization method is proposed by integrating an adaptive Kriging(A-Kriging)into an improved partial swarm optimization algorithm(IPSO)to give a so-called A-Kriging-IPSO for maximizing the bucklin...An effective hybrid optimization method is proposed by integrating an adaptive Kriging(A-Kriging)into an improved partial swarm optimization algorithm(IPSO)to give a so-called A-Kriging-IPSO for maximizing the buckling load of laminated composite plates(LCPs)under uniaxial and biaxial compressions.In this method,a novel iterative adaptive Kriging model,which is structured using two training sample sets as active and adaptive points,is utilized to directly predict the buckling load of the LCPs and to improve the efficiency of the optimization process.The active points are selected from the initial data set while the adaptive points are generated using the radial random-based convex samples.The cell-based smoothed discrete shear gap method(CS-DSG3)is employed to analyze the buckling behavior of the LCPs to provide the response of adaptive and input data sets.The buckling load of the LCPs is maximized by utilizing the IPSO algorithm.To demonstrate the efficiency and accuracy of the proposed methodology,the LCPs with different layers(2,3,4,and 10 layers),boundary conditions,aspect ratios and load patterns(biaxial and uniaxial loads)are investigated.The results obtained by proposed method are in good agreement with the literature results,but with less computational burden.By applying adaptive radial Kriging model,the accurate optimal resultsebased predictions of the buckling load are obtained for the studied LCPs.展开更多
The nonlinear vibration of graphene platelets reinforced composite corrugated(GPRCC)rectangular plates with shallow trapezoidal corrugations is investigated.Since graphene platelets are prone to agglomeration,a multi-...The nonlinear vibration of graphene platelets reinforced composite corrugated(GPRCC)rectangular plates with shallow trapezoidal corrugations is investigated.Since graphene platelets are prone to agglomeration,a multi-layer distribution is adopted here to match the engineering requirements.Firstly,an equivalent composite plate model is obtained,and then nonlinear equations of motion are derived by the von Kármán nonlinear geometric relationship and Hamilton’s principle.Afterwards,the Galerkin method and harmonic balance method are used to obtain an approximate analytical solution.Results show that the unit cell half period,unit cell inclination angle,unit cell height,graphene platelet dispersion pattern and graphene platelet weight fraction and geometry play important roles in the nonlinear vibration of the GPRCC plates.展开更多
A method is developed to predict the lateral load-carrying capacity of composite shear walls with double steel plates and filled concrete with binding bars(SCBs). Nonlinear finite element models of SCBs were establish...A method is developed to predict the lateral load-carrying capacity of composite shear walls with double steel plates and filled concrete with binding bars(SCBs). Nonlinear finite element models of SCBs were established by using the finite element tool, Abaqus. Tie constraints were used to connect the binding bars and the steel plates. Surface-to-surface contact provided by the Abaqus was used to simulate the interaction between the steel plate and the core concrete. The established models could predict the lateral load-carrying capacity of SCBs with a reasonable degree of accuracy. A calculation method was developed by superposition principle to predict the lateral load-carrying capacity of SCBs for the engineering application. The concrete confined by steel plates and binding bars is under multi-axial compression; therefore, its shear strength was calculated by using the Guo-Wang concrete failure criterion. The shear strength of the steel plates of SCBs was calculated by using the von Mises yielding criterion without considering buckling. Results of the developed method are in good agreement with the testing and finite element results.展开更多
Grouting pile is a new soft soil foundation treatment method with characteristics such as no vibration, no noise, no soil compaction, light construction machines and quick construction velocity and so on. At present, ...Grouting pile is a new soft soil foundation treatment method with characteristics such as no vibration, no noise, no soil compaction, light construction machines and quick construction velocity and so on. At present, study on reinforcement mechanism and design calculation method of composite foundation of grouting pile is initially started without design specifications, so it is usually required to draw on design specifications of stump pile when designing composite foundation of grouting pile while grouting pile has its characteristics and difference although reinforcement mechanisms and construction processes of two types of piles are similar. Sedimentation formula of composite foundation of grouting pile with cover plate is educed and a suitable deformation mode is proposed by aiming to deformation characteristics of composite foundation of grouting pile with cover plate under embankment load on basis of relevant sedimentation theories of composite foundation by combination of characteristics of composite foundation of grouting pile. The sedimentation calculation formula of grouting pile with cover plate under embankment load is educed according to balance relation of force and displacement coordination conditions by elastic theory and sedimentation calculation model established is validated by sedimentation monitoring documents of one expressway in China.展开更多
To develop electromagnetic protection composites with integrated structure -function properties, the three-dimension (3D) braided nickel plated carbon fiber/epoxy resin (Ni-CF3D/EP) composites were prepared based on 3...To develop electromagnetic protection composites with integrated structure -function properties, the three-dimension (3D) braided nickel plated carbon fiber/epoxy resin (Ni-CF3D/EP) composites were prepared based on 3D five-directional braiding, unitary nickel plating and mold compression shaping. The electromagnetic protection properties of Ni-CF3D/EP composites including shielding effective- ness (SE) and reflection loss against plane electromagnetic wave, shielding properties against electromagnetic pulse (EMP) were investigated. The test results show that the novel composites have good electromagnetic protection properties in a wide frequency range of 14 kHz～18 GHz with SE of 42 dB～95 dB, the absorption bandwidth of –5 dB in 2 GHz～18 GHz can reach 10 GHz and the pulse peak SE against EMP is 43.7 dB which can reduce the electromagnetic energy greatly. Meanwhile, the mechanic properties were also investi- gated and the results indicate that the Ni-CF3D/EP composites can replace metal materials for loading-bearing structural applications because of their excellent mechanic properties.展开更多
A new method of manufacturing micro-flow channels on graphite composite bipolar plate(GCBPP) microplaning using specially designed multi-tooth tool is proposed. In this method, several or even dozens of parallel micro...A new method of manufacturing micro-flow channels on graphite composite bipolar plate(GCBPP) microplaning using specially designed multi-tooth tool is proposed. In this method, several or even dozens of parallel micro-flow channels ranging from 100 μm to 500 μm in width can be produced simultaneously. But, edge chippings easily occur on the rib surface of GCBPP during microplaning due to brittleness of graphite composites. Experimental results show that edge chippings result in the increase of contact resistance between bipolar plate and carbon paper at low compaction force. While the edge chippings scarcely exert influence on the contact resistance at high compaction force. Contrary to conventional view, the edge chippings can significantly improve performance of microfuel cell and big edge chippings outperform small edge chippings. In addition, the influence of technical parameters on edge chippings was investigated in order to obtain big, but not oversized edge chippings.展开更多
Flexural and eigen-buckling analyses for rectangular steel-concrete partially composite plates(PCPs)with interlayer slip under simply supported and clamped boundary conditions are conducted using the weak form quadrat...Flexural and eigen-buckling analyses for rectangular steel-concrete partially composite plates(PCPs)with interlayer slip under simply supported and clamped boundary conditions are conducted using the weak form quadrature element method(QEM).Both of the derivatives and integrals in the variational description of a problem to be solved are directly evaluated by the aid of identical numerical interpolation points in the weak form QEM.The effectiveness of the presented numerical model is validated by comparing numerical results of the weak form QEM with those from FEM or analytic solution.It can be observed that only one quadrature element is fully competent for flexural and eigen-buckling analysis of a rectangular partially composite plate with shear connection stiffness commonly used.The numerical integration order of quadrature element can be adjusted neatly to meet the convergence requirement.The quadrature element model presented here is an effective and promising tool for further analysis of steel-concrete PCPs under more general circumstances.Parametric studies on the shear connection stiffness and length-width ratio of the plate are also presented.It is shown that the flexural deflections and the critical buckling loads of PCPs are significantly affected by the shear connection stiffness when its value is within a certain range.展开更多
The bending and stress analysis of a functionally graded polymer composite plate reinforced with graphene platelets are studied in this paper.The governing equations are derived by using principle of virtual work for ...The bending and stress analysis of a functionally graded polymer composite plate reinforced with graphene platelets are studied in this paper.The governing equations are derived by using principle of virtual work for a plate which is rested on Pasternak’s foundation.Sinusoidal shear deformation theory is used to describe displacement field.Four different distribution patterns are employed in our analysis.The analytical solution is presented for a functionally graded plate to investigate the influence of important parameters.The numerical results are presented to show the deflection and stress results of the problem for four employed patterns in terms of geometric parameters such as number of layers,weight fraction and two parameters of Pasternak’s foundation.展开更多
The effects of SiCp surface modifications(Cu coating,Ni coating and Ni/Cu coating)on the microstructures and mechanical properties of Al matrix composites were investigated.Surface modification of SiC particles with C...The effects of SiCp surface modifications(Cu coating,Ni coating and Ni/Cu coating)on the microstructures and mechanical properties of Al matrix composites were investigated.Surface modification of SiC particles with Cu,Ni and Cu/Ni,respectively,was carried out by electroless plating method.SiCp/Al composites were prepared by hot pressed sintering followed by hot extrusion.The results show that the surface modification of SiC particles plays an effective role,which is relative to the type of surface coating,and the interfacial bonding become stronger in the following order:untreated SiCp<Ni(Cu)-coated SiCp<Ni/Cu-coated SiCp.The Ni/Cu-coated SiCp/Al composites exhibit the best comprehensive mechanical properties,with ultimate tensile strength(σUTS)and fracture strain(εf)of 389 MPa and 6.3%,respectively.Compared with that of untreated-SiCp/Al composites,theσUTS andεf are enhanced by 19.3%and 57.5%.展开更多
Ni/n-SiO2 composite coating was electrodeposited by brush-plating with pulse-reverse current（RC）. The morphology, hardness, and tribological properties of the coating were investigated and compared with those of Ni ...Ni/n-SiO2 composite coating was electrodeposited by brush-plating with pulse-reverse current（RC）. The morphology, hardness, and tribological properties of the coating were investigated and compared with those of Ni and composite coatings electrodeposited with direct current（DC）. The results indicate that Ni/n-SiO2 composite coating electrodeposited by RC, because of RC and the nano powders, has denser coating, finer crystal grains, higher hardness（HV650.0, nearly 1.5 times higher than that of Ni coating electrodeposited by DC） and lower friction coefficient（nearly 0.62）, as a result, in the wearing experiment, the Ni/n-SiO2 composite coating electrodeposited by RC has the least worn loss. So this kind of coating has better wear resistance. And RC electro brush-plating can be used as a new technology of brush-plating in the area of wear resistance.展开更多
The coating of Ni W P was deposited as base layer, and then the composite coating of Ni Ti(particles) Re(rare earth) was deposited subsequently on the surface of diamond using electroless plating by adding 2...The coating of Ni W P was deposited as base layer, and then the composite coating of Ni Ti(particles) Re(rare earth) was deposited subsequently on the surface of diamond using electroless plating by adding 2～3 μm Ti particles and trace rare earth salt to bath solution. Ti particles deposited on the surface of diamond were found by SEM and formation of TiC was verified by X ray diffraction analysis after heat treatment of the coatings in vacuum at 900 ℃. The binding strength between the coated diamond and the metal matrix was improved effectively in the diamond composite based on metal cement.展开更多
文摘Because of an unfortunate mistake by authors,the Project(5227010679)of Foundation item was wrong.The corrected Project is shown as follows:Project(52271073).
基金Project(5227010679)supported by the National Natural Science Foundation of China。
文摘The process of preparing anodic oxide film containing active sites and electroless nickel plating on highly active rare earth magnesium alloy was developed.The formation mechanism of electroless nickel plating on active anodic oxide film and the structure and properties of the composite coating were studied by several surface and electrochemical techniques.The results showed that Ag nanograins with an average size of 10 nm were embedded into the anodic oxide film with pores of 0.1−2μm.Ag nanoparticles provided a catalytic site for the deposition of Ni-B alloy,and the Ni crystal nucleus was first grown in horizontal mode and then in cylindrical mode.The corrosion potential of the composite coating increased by 1.37 V and the corrosion current reduced two orders of magnitude due to the subsequent deposition of Ni-P alloy.The high corrosion resistance was attributed to the misaligning of these micro defects in the three different layers and the amorphous structure of the Ni-P alloy in the outer layer.These findings provide a new idea for electroless nickel plating on anodic oxide film.
基金Vietnam National Foundation for Science and Technology Development(NAFOSTED)under Grant number 107.02-2019.330.
文摘An effective hybrid optimization method is proposed by integrating an adaptive Kriging(A-Kriging)into an improved partial swarm optimization algorithm(IPSO)to give a so-called A-Kriging-IPSO for maximizing the buckling load of laminated composite plates(LCPs)under uniaxial and biaxial compressions.In this method,a novel iterative adaptive Kriging model,which is structured using two training sample sets as active and adaptive points,is utilized to directly predict the buckling load of the LCPs and to improve the efficiency of the optimization process.The active points are selected from the initial data set while the adaptive points are generated using the radial random-based convex samples.The cell-based smoothed discrete shear gap method(CS-DSG3)is employed to analyze the buckling behavior of the LCPs to provide the response of adaptive and input data sets.The buckling load of the LCPs is maximized by utilizing the IPSO algorithm.To demonstrate the efficiency and accuracy of the proposed methodology,the LCPs with different layers(2,3,4,and 10 layers),boundary conditions,aspect ratios and load patterns(biaxial and uniaxial loads)are investigated.The results obtained by proposed method are in good agreement with the literature results,but with less computational burden.By applying adaptive radial Kriging model,the accurate optimal resultsebased predictions of the buckling load are obtained for the studied LCPs.
基金Project(11972204) supported by the National Natural Science Foundation of China。
文摘The nonlinear vibration of graphene platelets reinforced composite corrugated(GPRCC)rectangular plates with shallow trapezoidal corrugations is investigated.Since graphene platelets are prone to agglomeration,a multi-layer distribution is adopted here to match the engineering requirements.Firstly,an equivalent composite plate model is obtained,and then nonlinear equations of motion are derived by the von Kármán nonlinear geometric relationship and Hamilton’s principle.Afterwards,the Galerkin method and harmonic balance method are used to obtain an approximate analytical solution.Results show that the unit cell half period,unit cell inclination angle,unit cell height,graphene platelet dispersion pattern and graphene platelet weight fraction and geometry play important roles in the nonlinear vibration of the GPRCC plates.
基金Project(51178333)supported by the National Natural Science Foundation of ChinaProject(SLDRCE09-D-03)supported by the Ministry of Science and Technology of China
文摘A method is developed to predict the lateral load-carrying capacity of composite shear walls with double steel plates and filled concrete with binding bars(SCBs). Nonlinear finite element models of SCBs were established by using the finite element tool, Abaqus. Tie constraints were used to connect the binding bars and the steel plates. Surface-to-surface contact provided by the Abaqus was used to simulate the interaction between the steel plate and the core concrete. The established models could predict the lateral load-carrying capacity of SCBs with a reasonable degree of accuracy. A calculation method was developed by superposition principle to predict the lateral load-carrying capacity of SCBs for the engineering application. The concrete confined by steel plates and binding bars is under multi-axial compression; therefore, its shear strength was calculated by using the Guo-Wang concrete failure criterion. The shear strength of the steel plates of SCBs was calculated by using the von Mises yielding criterion without considering buckling. Results of the developed method are in good agreement with the testing and finite element results.
文摘Grouting pile is a new soft soil foundation treatment method with characteristics such as no vibration, no noise, no soil compaction, light construction machines and quick construction velocity and so on. At present, study on reinforcement mechanism and design calculation method of composite foundation of grouting pile is initially started without design specifications, so it is usually required to draw on design specifications of stump pile when designing composite foundation of grouting pile while grouting pile has its characteristics and difference although reinforcement mechanisms and construction processes of two types of piles are similar. Sedimentation formula of composite foundation of grouting pile with cover plate is educed and a suitable deformation mode is proposed by aiming to deformation characteristics of composite foundation of grouting pile with cover plate under embankment load on basis of relevant sedimentation theories of composite foundation by combination of characteristics of composite foundation of grouting pile. The sedimentation calculation formula of grouting pile with cover plate under embankment load is educed according to balance relation of force and displacement coordination conditions by elastic theory and sedimentation calculation model established is validated by sedimentation monitoring documents of one expressway in China.
基金Project supported by Equipment Pre-research Foundation of China (9140A31030110JB3403)
文摘To develop electromagnetic protection composites with integrated structure -function properties, the three-dimension (3D) braided nickel plated carbon fiber/epoxy resin (Ni-CF3D/EP) composites were prepared based on 3D five-directional braiding, unitary nickel plating and mold compression shaping. The electromagnetic protection properties of Ni-CF3D/EP composites including shielding effective- ness (SE) and reflection loss against plane electromagnetic wave, shielding properties against electromagnetic pulse (EMP) were investigated. The test results show that the novel composites have good electromagnetic protection properties in a wide frequency range of 14 kHz～18 GHz with SE of 42 dB～95 dB, the absorption bandwidth of –5 dB in 2 GHz～18 GHz can reach 10 GHz and the pulse peak SE against EMP is 43.7 dB which can reduce the electromagnetic energy greatly. Meanwhile, the mechanic properties were also investi- gated and the results indicate that the Ni-CF3D/EP composites can replace metal materials for loading-bearing structural applications because of their excellent mechanic properties.
基金Project(51075155)supported by the National Natural Science Foundation of ChinaProject(2013ZZ017)supported by the Fundamental Research Funds for the Central Universities,China
文摘A new method of manufacturing micro-flow channels on graphite composite bipolar plate(GCBPP) microplaning using specially designed multi-tooth tool is proposed. In this method, several or even dozens of parallel micro-flow channels ranging from 100 μm to 500 μm in width can be produced simultaneously. But, edge chippings easily occur on the rib surface of GCBPP during microplaning due to brittleness of graphite composites. Experimental results show that edge chippings result in the increase of contact resistance between bipolar plate and carbon paper at low compaction force. While the edge chippings scarcely exert influence on the contact resistance at high compaction force. Contrary to conventional view, the edge chippings can significantly improve performance of microfuel cell and big edge chippings outperform small edge chippings. In addition, the influence of technical parameters on edge chippings was investigated in order to obtain big, but not oversized edge chippings.
基金Project(51508562)supported by the National Natural Science Foundation of ChinaProject(ZK18-03-49)supported by the Scientific Research Program of National University of Defense Technology,China
文摘Flexural and eigen-buckling analyses for rectangular steel-concrete partially composite plates(PCPs)with interlayer slip under simply supported and clamped boundary conditions are conducted using the weak form quadrature element method(QEM).Both of the derivatives and integrals in the variational description of a problem to be solved are directly evaluated by the aid of identical numerical interpolation points in the weak form QEM.The effectiveness of the presented numerical model is validated by comparing numerical results of the weak form QEM with those from FEM or analytic solution.It can be observed that only one quadrature element is fully competent for flexural and eigen-buckling analysis of a rectangular partially composite plate with shear connection stiffness commonly used.The numerical integration order of quadrature element can be adjusted neatly to meet the convergence requirement.The quadrature element model presented here is an effective and promising tool for further analysis of steel-concrete PCPs under more general circumstances.Parametric studies on the shear connection stiffness and length-width ratio of the plate are also presented.It is shown that the flexural deflections and the critical buckling loads of PCPs are significantly affected by the shear connection stiffness when its value is within a certain range.
基金the University of Kashan.(Grant Number:467893/0655)。
文摘The bending and stress analysis of a functionally graded polymer composite plate reinforced with graphene platelets are studied in this paper.The governing equations are derived by using principle of virtual work for a plate which is rested on Pasternak’s foundation.Sinusoidal shear deformation theory is used to describe displacement field.Four different distribution patterns are employed in our analysis.The analytical solution is presented for a functionally graded plate to investigate the influence of important parameters.The numerical results are presented to show the deflection and stress results of the problem for four employed patterns in terms of geometric parameters such as number of layers,weight fraction and two parameters of Pasternak’s foundation.
基金Project(2017zzts111)supported by the Fundamental Research Funds for the Central Universities,China。
文摘The effects of SiCp surface modifications(Cu coating,Ni coating and Ni/Cu coating)on the microstructures and mechanical properties of Al matrix composites were investigated.Surface modification of SiC particles with Cu,Ni and Cu/Ni,respectively,was carried out by electroless plating method.SiCp/Al composites were prepared by hot pressed sintering followed by hot extrusion.The results show that the surface modification of SiC particles plays an effective role,which is relative to the type of surface coating,and the interfacial bonding become stronger in the following order:untreated SiCp<Ni(Cu)-coated SiCp<Ni/Cu-coated SiCp.The Ni/Cu-coated SiCp/Al composites exhibit the best comprehensive mechanical properties,with ultimate tensile strength(σUTS)and fracture strain(εf)of 389 MPa and 6.3%,respectively.Compared with that of untreated-SiCp/Al composites,theσUTS andεf are enhanced by 19.3%and 57.5%.
文摘Ni/n-SiO2 composite coating was electrodeposited by brush-plating with pulse-reverse current（RC）. The morphology, hardness, and tribological properties of the coating were investigated and compared with those of Ni and composite coatings electrodeposited with direct current（DC）. The results indicate that Ni/n-SiO2 composite coating electrodeposited by RC, because of RC and the nano powders, has denser coating, finer crystal grains, higher hardness（HV650.0, nearly 1.5 times higher than that of Ni coating electrodeposited by DC） and lower friction coefficient（nearly 0.62）, as a result, in the wearing experiment, the Ni/n-SiO2 composite coating electrodeposited by RC has the least worn loss. So this kind of coating has better wear resistance. And RC electro brush-plating can be used as a new technology of brush-plating in the area of wear resistance.
文摘The coating of Ni W P was deposited as base layer, and then the composite coating of Ni Ti(particles) Re(rare earth) was deposited subsequently on the surface of diamond using electroless plating by adding 2～3 μm Ti particles and trace rare earth salt to bath solution. Ti particles deposited on the surface of diamond were found by SEM and formation of TiC was verified by X ray diffraction analysis after heat treatment of the coatings in vacuum at 900 ℃. The binding strength between the coated diamond and the metal matrix was improved effectively in the diamond composite based on metal cement.
