Permeable roads generally exhibit inferior mechanical properties and shorter service life than traditional dense-graded/impermeable roads.Furthermore,the incorporation of recycled aggregates in their construction may ...Permeable roads generally exhibit inferior mechanical properties and shorter service life than traditional dense-graded/impermeable roads.Furthermore,the incorporation of recycled aggregates in their construction may exacerbate these limitations.To address these issues,this study introduced a novel cement-stabilized permeable recycled aggregate material.A total of 162 beam specimens prepared with nine different levels of cement-aggregate ratio were tested to evaluate their permeability,bending load,and bending fatigue life.The experimental results indicate that increasing the content of recycled aggregates led to a reduction in both permeability and bending load.Additionally,the inclusion of recycled aggregates diminished the energy dissipation capacity of the specimens.These findings were used to establish a robust relationship between the initial damage in cement-stabilized permeable recycled aggregate material specimens and their fatigue life,and to propose a predictive model for their fatigue performance.Further,a method for assessing fatigue damage based on the evolution of fatigue-induced strain and energy dissipation was developed.The findings of this study provide valuable insights into the mechanical behavior and fatigue performance of cement-stabilized permeable recycled aggregate materials,offering guidance for the design of low-carbon-emission,permeable,and durable roadways incorporating recycled aggregates.展开更多
The effects of nanosecond laser shock peening without coating(LSPwC)and nanosecond stacked femtosecond laser shock peening compound strengthening(LSP-CS)on the surface integrity and fretting fatigue lifetime at 500℃o...The effects of nanosecond laser shock peening without coating(LSPwC)and nanosecond stacked femtosecond laser shock peening compound strengthening(LSP-CS)on the surface integrity and fretting fatigue lifetime at 500℃of GH 4169 dovetail component were investigated.The results show that LSP treatment does not significantly lead to changes in the grain size of GH 4169 alloy,but it introduces a large number of dislocations,resulting in the formation of a plastic deformation layer and residual compressive stress layer.The surface microhardness increased by 20.5%and 28.6%after being treated by LSPwC and LSP-CS,respectively.The surface residual compressive stresses were(-306.5±42.5)MPa and(-404.3±34.7)MPa,respectively;The depth of both the hardening layer and the residual compressive stress layer is 400μm,and along the cross-section with 0-100μm region after LSP-CS treatment has higher hardness and greater residual compressive stress.The fretting fatigue lifetime of the GH 4169 dovetail component at 500℃was increased by 346.8%and 494.9%,which is the result of the combined effects of the hardening layer and the residual stress layer.The LSP-CS treatment can effectively make up for the disadvantage of the LSPwC treatment,and further enhance the fretting fatigue lifetime of the GH 4169 dovetail component at high temperature.展开更多
The fatigue load spectrum and operation life evaluation of key components in the catenary system under the high speed train running condition were investigated.Firstly,based on the catenary model and pantograph model,...The fatigue load spectrum and operation life evaluation of key components in the catenary system under the high speed train running condition were investigated.Firstly,based on the catenary model and pantograph model,the couple dynamic equations of pantograph–catenary were built with the Lagrange’s method;then the dynamic contact force was obtained by the Newmark method at the train speeds of 250,280 and 300 km/h,respectively.Secondly,the finite element model(FEM)of one anchor section’s catenary was built to analyze its transient response under the contact force as train running;then the loading time history of messenger wire base,steady arm,registration tube,oblique cantilever,and straight cantilever were extracted.Finally,the key components’fatigue spectrum was carried out by the rain-flow counting method,and operation life was estimated in consideration of such coefficients,such as stress concentration,shape and dimension,surface treatment.The results show that the fatigue life of the catenary system reduces with the increasing of train speed;specifically,the evaluated fatigue life of the steady arm is shorter than other components.展开更多
The fatigue performance of a workpiece depends on its surface quality.In traditional fatigue life prediction,the effect of surface quality is commonly accounted for by using empirical correction factors,which is impre...The fatigue performance of a workpiece depends on its surface quality.In traditional fatigue life prediction,the effect of surface quality is commonly accounted for by using empirical correction factors,which is imprecise when safety is of great concern.For surface quality,the surface topography is an important parameter,which introduces stress concentration that reduces the fatigue life.It is not feasible to test the stress concentration of different surface topographies.On the one hand,it is time-consuming and high-cost,and on the other hand,it cannot reflect the general statistical characteristics.With the help of surface reconstruction technology and interpolation method,a more efficient and economic approach is proposed,where FE simulation of workpiece with the reconstructed surface topography is used as a foundation for fatigue life prediction.The relationship between surface roughness(Sa)and fatigue life of the workpiece is studied with the proposed approach.展开更多
The effect of key parameters on fatigue life of common metallic components, e.g. steel, aluminium alloy, has been analysed quantitatively. The influential coverage and degree of these parameters have been investigated...The effect of key parameters on fatigue life of common metallic components, e.g. steel, aluminium alloy, has been analysed quantitatively. The influential coverage and degree of these parameters have been investigated systematically, some phenomena which can′t be discovered with qualitative analysis method have been revealed, a series of valuable conclusions has been obtained, which would be very beneficial to fatigue resistant design and improvement of anti fatigue ability of metallic components.展开更多
The advantage of built-up sleeved backup roll was described. Based on the stress distribution analysis and simulation for the built-up sleeved backup roll by using finite element method, the effects of roll sleeve thi...The advantage of built-up sleeved backup roll was described. Based on the stress distribution analysis and simulation for the built-up sleeved backup roll by using finite element method, the effects of roll sleeve thickness and shrink range on the stress-strain field were studied. Finally, based on the methodology and strategy of the fatigue analysis, fatigue life of backup roll was estimated by using the stress-strain data obtained through finite element simulation. The results show that roll sleeve thickness and shrink range have a great influence on sleeve stress distribution of built-up sleeved roll. Under the circumstance of ensuring transferring enough torque, the shrink range should be kept small. However, thicker roll sleeve has longer roll service life when the shrink range is constant.展开更多
The fatigue life for components can be predicted by the plot method which is easy and convenient in engineering. Based on the usual fatigue life prediction formula, a new formula for estimating the low stress and hig...The fatigue life for components can be predicted by the plot method which is easy and convenient in engineering. Based on the usual fatigue life prediction formula, a new formula for estimating the low stress and high cycle fatigue life is proposed and deduced, which has adopted more accurate SN curve relationship——WeibullSN curve formula. The solution of the new formula is given, too. In addition, an example has been calculated and proved in practice. The results of the new formula and the old one are given and compared.展开更多
This paper used Baumel Jr. and Seeger’s approach estimating fatigue parameters of 48MnV with 3Cr13 coatings. The fatigue life of the crankshaft of a six-cylinder engine, repaired by twin arc spraying 3cr13 deposits, ...This paper used Baumel Jr. and Seeger’s approach estimating fatigue parameters of 48MnV with 3Cr13 coatings. The fatigue life of the crankshaft of a six-cylinder engine, repaired by twin arc spraying 3cr13 deposits, is respectively calculated using different damage model such as S-N method, normal strain approaches, SWT-Bannantine approaches, shear strain approaches, and fatemi-Socie method based on dynamical simulation and FE analysis of crankshaft. The results indicate that the traditional calculation is conservative and that the life of crankshaft repaired by arc spraying is sufficient.展开更多
A fatigue damage model is developed for evaluating accumulative fatigue damage of dumpers. The loading spectrums acted on dumpers are created according to measured strain data in field. The finite element analysis is ...A fatigue damage model is developed for evaluating accumulative fatigue damage of dumpers. The loading spectrums acted on dumpers are created according to measured strain data in field. The finite element analysis is carried out for assessing stress distribution and strength characteristics of dumpers. Fatigue damage indexes and service life are calculated by a modified Palmgren-Miner rule. The investigation shows that fatigue notch factor has a significant influence on the calculation of fatigue damage of dumpers.展开更多
The effects of laser shock peening (LSP) on improving fatigue life of aluminum alloy 7050 are investigated.Surface hardness is increased corresponding to a high dislocation density induced by LSP.The X-ray diffraction...The effects of laser shock peening (LSP) on improving fatigue life of aluminum alloy 7050 are investigated.Surface hardness is increased corresponding to a high dislocation density induced by LSP.The X-ray diffraction stress measurement shows that LSP results in prominent increase of surface compressive stress,quasi-symmetrically distributed in the laser peened region.The fatigue life of the alloy 7050 in rivet fastener hole structure is notably improved owing to LSP.The sequence of LSP and fastener hole preparation also influence the fatigue cycle life of the alloy.展开更多
基金Project(2024JJ2073)supported by the Science Fund for Distinguished Young Scholars of Hunan Province,ChinaProjects(2023YFC3807205,2019YFC1904704)+4 种基金supported by the National Key R&D Program of ChinaProject(52178443)supported by the National Natural Science Foundation of ChinaProject(2024ZZTS0109)supported by Fundamental Research Funds for the Central Universities of Central South University,China。
文摘Permeable roads generally exhibit inferior mechanical properties and shorter service life than traditional dense-graded/impermeable roads.Furthermore,the incorporation of recycled aggregates in their construction may exacerbate these limitations.To address these issues,this study introduced a novel cement-stabilized permeable recycled aggregate material.A total of 162 beam specimens prepared with nine different levels of cement-aggregate ratio were tested to evaluate their permeability,bending load,and bending fatigue life.The experimental results indicate that increasing the content of recycled aggregates led to a reduction in both permeability and bending load.Additionally,the inclusion of recycled aggregates diminished the energy dissipation capacity of the specimens.These findings were used to establish a robust relationship between the initial damage in cement-stabilized permeable recycled aggregate material specimens and their fatigue life,and to propose a predictive model for their fatigue performance.Further,a method for assessing fatigue damage based on the evolution of fatigue-induced strain and energy dissipation was developed.The findings of this study provide valuable insights into the mechanical behavior and fatigue performance of cement-stabilized permeable recycled aggregate materials,offering guidance for the design of low-carbon-emission,permeable,and durable roadways incorporating recycled aggregates.
基金Project(2022YFB3401900)supported by the the National Key R&D of ChinaProject(2025YFHZ0163)supported by the the Science and Technology Projects in Sichuan Province,ChinaProject(2682024GF004)supported by Fundamental Research Funds for the Centeral University,China。
文摘The effects of nanosecond laser shock peening without coating(LSPwC)and nanosecond stacked femtosecond laser shock peening compound strengthening(LSP-CS)on the surface integrity and fretting fatigue lifetime at 500℃of GH 4169 dovetail component were investigated.The results show that LSP treatment does not significantly lead to changes in the grain size of GH 4169 alloy,but it introduces a large number of dislocations,resulting in the formation of a plastic deformation layer and residual compressive stress layer.The surface microhardness increased by 20.5%and 28.6%after being treated by LSPwC and LSP-CS,respectively.The surface residual compressive stresses were(-306.5±42.5)MPa and(-404.3±34.7)MPa,respectively;The depth of both the hardening layer and the residual compressive stress layer is 400μm,and along the cross-section with 0-100μm region after LSP-CS treatment has higher hardness and greater residual compressive stress.The fretting fatigue lifetime of the GH 4169 dovetail component at 500℃was increased by 346.8%and 494.9%,which is the result of the combined effects of the hardening layer and the residual stress layer.The LSP-CS treatment can effectively make up for the disadvantage of the LSPwC treatment,and further enhance the fretting fatigue lifetime of the GH 4169 dovetail component at high temperature.
基金Project(51175383)supported by the National Natural Science Foundation of China(NSF)
文摘The fatigue load spectrum and operation life evaluation of key components in the catenary system under the high speed train running condition were investigated.Firstly,based on the catenary model and pantograph model,the couple dynamic equations of pantograph–catenary were built with the Lagrange’s method;then the dynamic contact force was obtained by the Newmark method at the train speeds of 250,280 and 300 km/h,respectively.Secondly,the finite element model(FEM)of one anchor section’s catenary was built to analyze its transient response under the contact force as train running;then the loading time history of messenger wire base,steady arm,registration tube,oblique cantilever,and straight cantilever were extracted.Finally,the key components’fatigue spectrum was carried out by the rain-flow counting method,and operation life was estimated in consideration of such coefficients,such as stress concentration,shape and dimension,surface treatment.The results show that the fatigue life of the catenary system reduces with the increasing of train speed;specifically,the evaluated fatigue life of the steady arm is shorter than other components.
基金Projects(51535012,U1604255)supported by the National Natural Science Foundation of ChinaProject(2016JC2001)supported by the Key Research and Development Project of Hunan Province,China
文摘The fatigue performance of a workpiece depends on its surface quality.In traditional fatigue life prediction,the effect of surface quality is commonly accounted for by using empirical correction factors,which is imprecise when safety is of great concern.For surface quality,the surface topography is an important parameter,which introduces stress concentration that reduces the fatigue life.It is not feasible to test the stress concentration of different surface topographies.On the one hand,it is time-consuming and high-cost,and on the other hand,it cannot reflect the general statistical characteristics.With the help of surface reconstruction technology and interpolation method,a more efficient and economic approach is proposed,where FE simulation of workpiece with the reconstructed surface topography is used as a foundation for fatigue life prediction.The relationship between surface roughness(Sa)and fatigue life of the workpiece is studied with the proposed approach.
基金TheFoundationforScholarsReturnedfromOverseaCNNC! (No .970 48 2 )
文摘The effect of key parameters on fatigue life of common metallic components, e.g. steel, aluminium alloy, has been analysed quantitatively. The influential coverage and degree of these parameters have been investigated systematically, some phenomena which can′t be discovered with qualitative analysis method have been revealed, a series of valuable conclusions has been obtained, which would be very beneficial to fatigue resistant design and improvement of anti fatigue ability of metallic components.
基金Project(E2010001155) supported by the Natural Science Foundation of Hebei Province, China
文摘The advantage of built-up sleeved backup roll was described. Based on the stress distribution analysis and simulation for the built-up sleeved backup roll by using finite element method, the effects of roll sleeve thickness and shrink range on the stress-strain field were studied. Finally, based on the methodology and strategy of the fatigue analysis, fatigue life of backup roll was estimated by using the stress-strain data obtained through finite element simulation. The results show that roll sleeve thickness and shrink range have a great influence on sleeve stress distribution of built-up sleeved roll. Under the circumstance of ensuring transferring enough torque, the shrink range should be kept small. However, thicker roll sleeve has longer roll service life when the shrink range is constant.
文摘The fatigue life for components can be predicted by the plot method which is easy and convenient in engineering. Based on the usual fatigue life prediction formula, a new formula for estimating the low stress and high cycle fatigue life is proposed and deduced, which has adopted more accurate SN curve relationship——WeibullSN curve formula. The solution of the new formula is given, too. In addition, an example has been calculated and proved in practice. The results of the new formula and the old one are given and compared.
文摘This paper used Baumel Jr. and Seeger’s approach estimating fatigue parameters of 48MnV with 3Cr13 coatings. The fatigue life of the crankshaft of a six-cylinder engine, repaired by twin arc spraying 3cr13 deposits, is respectively calculated using different damage model such as S-N method, normal strain approaches, SWT-Bannantine approaches, shear strain approaches, and fatemi-Socie method based on dynamical simulation and FE analysis of crankshaft. The results indicate that the traditional calculation is conservative and that the life of crankshaft repaired by arc spraying is sufficient.
文摘A fatigue damage model is developed for evaluating accumulative fatigue damage of dumpers. The loading spectrums acted on dumpers are created according to measured strain data in field. The finite element analysis is carried out for assessing stress distribution and strength characteristics of dumpers. Fatigue damage indexes and service life are calculated by a modified Palmgren-Miner rule. The investigation shows that fatigue notch factor has a significant influence on the calculation of fatigue damage of dumpers.
文摘The effects of laser shock peening (LSP) on improving fatigue life of aluminum alloy 7050 are investigated.Surface hardness is increased corresponding to a high dislocation density induced by LSP.The X-ray diffraction stress measurement shows that LSP results in prominent increase of surface compressive stress,quasi-symmetrically distributed in the laser peened region.The fatigue life of the alloy 7050 in rivet fastener hole structure is notably improved owing to LSP.The sequence of LSP and fastener hole preparation also influence the fatigue cycle life of the alloy.
