Ice load on underwater vehicles breaking through ice covers from underneath is a significant concern for researchers in polar exploration,and the research on this problem is still in its early stages.Both mechanical e...Ice load on underwater vehicles breaking through ice covers from underneath is a significant concern for researchers in polar exploration,and the research on this problem is still in its early stages.Both mechanical experimental measurement and numerical simulation pose research challenges.This study focuses on the ice load of a cylinder structure breaking upward through the ice sheet form underneath in the Small Ice Model Basin of China Ship Scientific Research Center(CSSRC SIMB).A high-speed camera system was employed to observe the ice sheet failure during the tests,in which,with the loading position as center,local radial cracks and circumferential cracks were generated.A load sensor was used to measure the overall ice load during this process.Meanwhile,a numerical model was developed using LS-DYNA for validation and comparison.With this model,numerical simulation was conducted under various ice thicknesses and upgoing speeds to analyze the instantaneous curves of ice load.The calculation results were statistically analyzed under different working conditions to determine the influence of the factors on the ice load of the cylinder.The study explores the measurement method about ice load of objects vertically breaking through model ice sheet and is expected to provide some fundamental insights into the safety design of underwater structures operating in ice waters.展开更多
With the development of high energy solid propellants,it is critical to evaluate the safety and power performance of solid propellants in the face of threats such as unmanned aerial vehicles(UAVs)when transporting and...With the development of high energy solid propellants,it is critical to evaluate the safety and power performance of solid propellants in the face of threats such as unmanned aerial vehicles(UAVs)when transporting and using them in contemporary warfare.An electric probe-type cylinder test measured the displacement-time behavior of NEPE high-energy solid propellant,and the parameters of the Jones-Wilkins-Lee(JWL)equation of state(EOS)were derived using particle swarm optimization(PSO)with the Gurney energy model.Further,the parameters of JWL-Miller EOS,determined through AUTODYN simulations,were validated by comparing airburst process simulations with experimental overpressure data.The study established a method for determining EOS parameters of high-energy propellants,achieving a high degree of accuracy.The derived parameters ensure precise modeling of propellant behavior,offering a reliable foundation for future applications in solid rocket motor performance optimization and safety assessment.展开更多
The contact strength calculation of two curved rough surfaces is a forefront issue of Hertz contact theory and method. Associated rules between rough surface characterization parameters(correlation length, and root me...The contact strength calculation of two curved rough surfaces is a forefront issue of Hertz contact theory and method. Associated rules between rough surface characterization parameters(correlation length, and root mean square deviation) and contact characteristic parameters(contact area, maximum contact pressure, contact number, and contact width) of two rough cylinders are mainly studied. The contact model of rough cylinders is deduced based on GW model. As there is no analytical solution for the pressure distribution equation, an approximate iterative solution method for the pressure distribution is adopted. Furthermore, the quantitative relationships among the correlation length, the root mean square deviation, the asperity radius of curvature and the asperity density are also obtained based on a numerical simulation method. The maximum contact pressure and the contact number decrease with the increase of correlation length, while the contact width and the contact area are on the contrary. The contact width increases with the increase of root mean square deviation while the maximum contact pressure, the contact area and the contact number decrease.展开更多
The PnP problem is a widely used technique for pose determination in computer vision community,and finding out geometric conditions of multiple solutions is the ultimate and most desirable goal of the multi-solution a...The PnP problem is a widely used technique for pose determination in computer vision community,and finding out geometric conditions of multiple solutions is the ultimate and most desirable goal of the multi-solution analysis,which is also a key research issue of the problem.In this paper,we prove that given 3 control points,if the camera's optical center lies on the so-called“danger cylinder”and is enough far from the supporting plane of control points,the corresponding P3P problem must have 3 positive solutions.This result can bring some new insights into a better understanding of the multi-solution problem.For example,it is shown in the literature that the solution of the P3P problem is instable if the optical center lies on this danger cylinder,we think such occurrence of triple-solution is the primary source of this instability.展开更多
In this study, the laminar heat transfer and nanofluid flow between two porous horizontal concentric cylinders was investigated. The problem is investigated in two different geometries and the Re=10, 25, 50, 75, 100 a...In this study, the laminar heat transfer and nanofluid flow between two porous horizontal concentric cylinders was investigated. The problem is investigated in two different geometries and the Re=10, 25, 50, 75, 100 and volume fraction 0, 0.2%, 0.5%, 2% and 5% that related to copper nanoparticles, and porous medium porosity of 0.5 and 0.9. Compared to the first geometry, the convective coefficient in the second geometry increases by 8.3%, 7% and 5.5% at Reynolds numbers of 100, 75 and 50, respectively. Comparison of the outlet temperatures for two heat fluxes of 300 and 1200 W/m^2 indicates a 2.5% temperature growth by a fourfold increase in the heat fluxes. Also, the higher Nusselt number is associated with the second geometry occurring at porosities of 0.9 and 0.5, respectively. In both geometries, the Nusselt number values at the porosity of 0.9 are higher, which is due to the increased nanofluid convection at higher porosities. The velocity of the nanofluid experiences a two-fold increase at the outlet compared to its inlet velocity in the first geometry and for both porosities. Similarly, a three-fold increase was achieved in the second geometry and for both porosities.展开更多
We suppose that in order to maintain high accuracy of holes and to lower residual stresses after cold expansion of thick-walled cylinders, which undergo cross-section plastic deformation, it is necessary to perform ax...We suppose that in order to maintain high accuracy of holes and to lower residual stresses after cold expansion of thick-walled cylinders, which undergo cross-section plastic deformation, it is necessary to perform axial plastic compression and subsequent cold expansion with small interferences. To test this hypothesis, we studied hoop, radial and axial residual stresses in cylinders made of carbon steel AISI 1050 with hole diameter of 5 mm, outer diameter of 15 mm and length of 30 mm by Sachs method as well as accuracy of expanded holes. It is found that double cold expansion with total interference equal to 5.1% generates hoop residual stresses with largest absolute value equal to 284 MPa and ensures high holes accuracy(IT7). After plastic compression with strain equal to 0.5 and 1% the mentioned stresses reduced to 120 and 75 MPa respectively,and accuracy of the holes reduced as well. Subsequent cold expansion with small interference equal to 0.9% helps to restore holes accuracy(IT7)gained by double cold expansion and ensure that absolute value of hoop residual stresses(177 MPa) is lower compared to double cold expansion.展开更多
The interaction of surrounding rock with a support system in deep underground tunnels has attracted extensive interest from researchers.However,the effect of high axial stress on tunnel stability has not been fully co...The interaction of surrounding rock with a support system in deep underground tunnels has attracted extensive interest from researchers.However,the effect of high axial stress on tunnel stability has not been fully considered.In this study,compression tests with and without confining pressure were conducted on solid specimens and hollow cylinder specimens filled with aluminium,lead,and polymethyl methacrylate(PMMA)to investigate the strength,deformation and failure characteristics of circular roadways subjected to high axial stress.The influence of the three-dimensional stress on the surrounding rock supported with different stiffness was studied.The results indicate that the strength and peak strain of hollow cylinders filled with PMMA are higher than those of hollow cylinders filled with aluminium or lead,indicating that flexible retaining is beneficial for roadway stability.The results obtained in this paper can contribute to better understanding the support failure of a buried roadway subjected to high axial stress and thus to analyzing and evaluating roadway stability.展开更多
The flow pattern behaviour of falling liquid film over three horizontal cylinders was evaluated.These flows can take three forms:discrete droplets,individual jets,and continuous sheet,and special attention is paid to ...The flow pattern behaviour of falling liquid film over three horizontal cylinders was evaluated.These flows can take three forms:discrete droplets,individual jets,and continuous sheet,and special attention is paid to the effects of the physical properties and geometrical parameters of the first two forms(droplets and jets) because these forms are more important in heat-transfer behaviour and less research has been published for these forms,The flow modes and experimental results were successfully compared with previous experimental literatures,and also the effects of liquid flow rate,tube diameter,and tube spacing on departure site spacing,in both drop and jet modes,were evaluated in the low Galileo number and high viscosity fluid(cooking oil),to help developing criteria for determining falling film modes and their transitions,and to understand the heat transfer characteristics associated with each mode.展开更多
Hydraulic cylinder is a primary component of the hydraulic valve systems.The numerical study of hydraulic cylinder to evaluate the stress analysis,the life assessment and the performance of operation characteristics i...Hydraulic cylinder is a primary component of the hydraulic valve systems.The numerical study of hydraulic cylinder to evaluate the stress analysis,the life assessment and the performance of operation characteristics in hydraulic cylinder were described.The calculation of safety factor,fatigue life,piston chamber pressure,rod chamber pressure and the change of velocity of piston with flow time after the beginning of hydraulic cylinder were incorporated.Numerical analysis was performed using the commercial CFD code,ANSYS with unsteady,dynamic mesh model,two-way FSI(fluid-structure interaction)method and k-εturbulent model.The internal pressure in hydraulic cylinder through stress analysis show higher than those of the yield strength.展开更多
The system considered in this work consists of a cylinder which is controlled by a pair of three-way servo valves rather than a four-way one.Therefore,the cylinder output stiffness is independently controllable of the...The system considered in this work consists of a cylinder which is controlled by a pair of three-way servo valves rather than a four-way one.Therefore,the cylinder output stiffness is independently controllable of the output force.A discontinuous projection based adaptive robust controller (ARC) was constructed to achieve high-accuracy output force trajectory tracking for the system.In ARC,on-line parameter adaptation method was adopted to reduce the extent of parametric uncertainties due to the variation of friction parameters,and sliding mode control method was utilized to attenuate the effects of parameter estimation errors,unmodelled dynamics and disturbance.Furthermore,output stiffness maximization/minimization was introduced to fulfill the requirement of many robotic applications.Extensive experimental results were presented to illustrate the effectiveness and the achievable performance of the proposed scheme.For tracking a 0.5 Hz sinusoidal trajectory,maximum tracking error is 4.1 N and average tracking error is 2.2 N.Meanwhile,the output stiffness can be made and maintained near its maximum/minimum.展开更多
The stress state around circular openings,such as boreholes,shafts,and tunnels,is usually needed to be evaluated.Solutions for stresses,strains and ultimate bearing capacities of pressurized hollow cylinder are common...The stress state around circular openings,such as boreholes,shafts,and tunnels,is usually needed to be evaluated.Solutions for stresses,strains and ultimate bearing capacities of pressurized hollow cylinder are common cases.Stress analytical method for plane problem of a double-layered thick-walled cylinder subjected to a type of non-uniform pressure on the outer surface and uniform radial pressure on the inner surface is given.The power series method of complex function is used.The stress analytical solution is obtained with the assumption that two layers of a cylinder are fully contacted.The distributions of normal and tangential contact stress along the interface,tangential stress on the inner boundary and stresses in the radial direction at θ=0°,45° and 90°,are obtained.An example indicates that,when the elastic modulus of the inner layer of a double-layered thick-walled cylinder is smaller than that of the outer layer,the tangential stress is smaller than that in the corresponding point for a traditional cylinder composed of homogeneous materials.In that way,stress concentration at the inner surface can be alleviated and the stress distribution is more uniform.This is a capable way to enhance the elastic ultimate bearing capacity of thick-walled cylinder.展开更多
ABE-KONDOH-NAGANO,ABID,YANG-SHIH and LAUNDER-SHARMA low-Reynolds number turbulence models were applied to simulating unsteady turbulence flow around a square cylinder in different phases flow field and time-averaged u...ABE-KONDOH-NAGANO,ABID,YANG-SHIH and LAUNDER-SHARMA low-Reynolds number turbulence models were applied to simulating unsteady turbulence flow around a square cylinder in different phases flow field and time-averaged unsteady flow field.Meanwhile,drag and lift coefficients of the four different low-Reynolds number turbulence models were analyzed.The simulated results of YANG-SHIH model are close to the large eddy simulation results and experimental results,and they are significantly better than those of ABE-KONDOH-NAGANO,ABID and LAUNDER-SHARMR models.The modification of the generation of turbulence kinetic energy is the key factor to a successful simulation for YANG-SHIH model,while the correction of the turbulence near the wall has minor influence on the simulation results.For ABE-KONDOH-NAGANO,ABID and LAUNDER-SHARMA models satisfactory simulation results cannot be obtained due to lack of the modification of the generation of turbulence kinetic energy.With the joint force of wall function and the turbulence models with the adoption of corrected swirl stream,flow around a square cylinder can be fully simulated with less grids by the near-wall.展开更多
Cooling strength is one of the important factors affecting microstructure and properties of gas cylinders during quenching process,and reasonable water spray volume can effectively improve the quality of gas cylinders...Cooling strength is one of the important factors affecting microstructure and properties of gas cylinders during quenching process,and reasonable water spray volume can effectively improve the quality of gas cylinders and reduce production costs.To find the optimal water spray parameters,a fluid-solid coupling model with three-phase flow was established in consideration of water-vapor conversion.The inner and outer walls of gas cylinder with the dimensions of d914 mm×38 mm×12000 mm were quenched using multi-nozzle water spray system.The internal pressure,average heat transfer coefficient(have)and stress of the gas cylinder under different water spray volumes during quenching process were studied.Finally,the mathematical model was experimentally verified.The results show that both the internal pressure and have increase along with the increase of spray volume.The internal pressure increases slowly first and then rapidly,but have increases rapidly first and then slowly.To satisfy hardenability of gas cylinders,the minimum spray volume should not be less than 40 m^3/(h·m).The results of stress indicate that water spray quenching will not cause deformation of bottle body in the range of water volume from 40 to 290 m^3/(h·m).展开更多
This study investigated numerically the characteristics of laminar flow around two identical circular cylinders placed in tandem, with slits of the same width through their respective axis. The center to center distan...This study investigated numerically the characteristics of laminar flow around two identical circular cylinders placed in tandem, with slits of the same width through their respective axis. The center to center distance between the cylinders and the slit orientation were varied to study their effects on the flow structure, lift and drag, and vortex shedding characteristics. It was found that three flow regimes could be distinguished, the transitions between which could be indicated by the sudden changes in drag and lift. Asymmetrically, configured slits destabilized the stagnant region between cylinders;whereas in-line slits connect the two cylinders to act as a single elongated bluff body, even at large cylinder separation, by stabilizing the stagnant region in between. These in turn strongly modified the transition between flow regimes. Vortex shedding was also strongly influenced by both slit configuration and cylinder separation.展开更多
Combined effects of Soret(thermal-diffusion) and Dufour(diffusion-thermo) in MHD stagnation point flow by a permeable stretching cylinder were studied. Analysis was examined in the presence of heat generation/absorpti...Combined effects of Soret(thermal-diffusion) and Dufour(diffusion-thermo) in MHD stagnation point flow by a permeable stretching cylinder were studied. Analysis was examined in the presence of heat generation/absorption and chemical reaction. The laws of conservation of mass, momentum, energy and concentration are found to lead to the mathematical development of the problem. Suitable transformations were used to convert the nonlinear partial differential equations into the ordinary differential equations. The series solutions of boundary layer equations through momentum, energy and concentration equations were obtained.Convergence of the developed series solutions was discussed via plots and numerical values. The behaviors of different physical parameters on the velocity components, temperature and concentration were obtained. Numerical values of Nusselt number, skin friction and Sherwood number with different parameters were computed and analyzed. It is found that Dufour and Soret numbers result in the enhancement of temperature and concentration distributions, respectively.展开更多
Ultra-large plate forgings are foundation of heavy machinery,but many parts of the type cannot be made by conventional technologies due to the characters of extreme manufacturing in terms of size and quality requireme...Ultra-large plate forgings are foundation of heavy machinery,but many parts of the type cannot be made by conventional technologies due to the characters of extreme manufacturing in terms of size and quality requirements.This paper introduced a systematically method called cylinder unfolding method(CUM)for producing large plate forgings,by using a serial of operations including“splitting”,“unfolding”,and“flattening”of a thick cylinder obtained from saddle forging.The technological route of CUM was presented in detail with an example of plate forging with the horizontal sizes of 6100 mm and thickness of 300 mm.The deformation features of saddle forging for fabricating transitional cylinders were analyzed,and then the subsequent handling steps including splitting,unfolding and flattening of the cylinder,as well as the auxiliary processing,were addressed.The practice proved that CUM can provide an efficient way for manufacturing ultra-large plate forgings and meet the strict requirements in geometry and mechanical performance,without highly increasing the investments of forming equipment and tooling.展开更多
The optimal design of heating and cooling systems must take into account heat radiation which is a non-linear process.In this study,the mixed convection in a radiative magnetohydrodynamic Eyring-Powell copperwater nan...The optimal design of heating and cooling systems must take into account heat radiation which is a non-linear process.In this study,the mixed convection in a radiative magnetohydrodynamic Eyring-Powell copperwater nanofluid over a stretching cylinder was investigated.The energy balance is modeled,taking into account the non-linear thermal radiation and a thermal slip condition.The effects of the embedded flow parameters on the fluid properties,as well as on the skin friction coefficient and heat transfer rate,are analyzed.Unlike in many existing studies,the recent spectral quasi-linearization method is used to solve the coupled nonlinear boundary-value problem.The computational result shows that increasing the nanoparticle volume fraction,thermal radiation parameter and heat generation parameter enhances temperature profile.We found that the velocity slip parameter and the fluid material parameter enhance the skin friction.A comparison of the current numerical results with existing literature for some limiting cases shows excellent agreement.展开更多
Because of the mixed grain and coarse grain structure, the long heat treatment cycle and large energy conservation in the heavy cylinder heat treatment process, the up ladder type and terraced type normalizing heat tr...Because of the mixed grain and coarse grain structure, the long heat treatment cycle and large energy conservation in the heavy cylinder heat treatment process, the up ladder type and terraced type normalizing heat treatment of heavy cylinder after rolling were put forward. The microstructure and mechanical properties of 2.25Cr1Mo0.25 V steel after the up ladder type normalizing, terraced type normalizing and isothermal type normalizing were studied. Experimental results show that： 1） For the grain refinement, the twice terraced type normalizing is better than the up ladder type and isothermal type normalizing, and the average grain size is 18 μm; 2） The yield strength, tensile strength and-30℃ charpy impact energy after twice terraced type normalizing are 681 MPa, 768 MPa and 181 J, respectively, and the mechanical properties are better than those of the up ladder type and isothermal type normalizing; 3） Compared with the isothermal type normalizing, the holding time of terraced type normalizing can be shortened by 30%, which greatly reduces the energy consumption.展开更多
文摘Ice load on underwater vehicles breaking through ice covers from underneath is a significant concern for researchers in polar exploration,and the research on this problem is still in its early stages.Both mechanical experimental measurement and numerical simulation pose research challenges.This study focuses on the ice load of a cylinder structure breaking upward through the ice sheet form underneath in the Small Ice Model Basin of China Ship Scientific Research Center(CSSRC SIMB).A high-speed camera system was employed to observe the ice sheet failure during the tests,in which,with the loading position as center,local radial cracks and circumferential cracks were generated.A load sensor was used to measure the overall ice load during this process.Meanwhile,a numerical model was developed using LS-DYNA for validation and comparison.With this model,numerical simulation was conducted under various ice thicknesses and upgoing speeds to analyze the instantaneous curves of ice load.The calculation results were statistically analyzed under different working conditions to determine the influence of the factors on the ice load of the cylinder.The study explores the measurement method about ice load of objects vertically breaking through model ice sheet and is expected to provide some fundamental insights into the safety design of underwater structures operating in ice waters.
基金supported by"the Fundamental Research Funds for the Central Universities",No.30924010503.
文摘With the development of high energy solid propellants,it is critical to evaluate the safety and power performance of solid propellants in the face of threats such as unmanned aerial vehicles(UAVs)when transporting and using them in contemporary warfare.An electric probe-type cylinder test measured the displacement-time behavior of NEPE high-energy solid propellant,and the parameters of the Jones-Wilkins-Lee(JWL)equation of state(EOS)were derived using particle swarm optimization(PSO)with the Gurney energy model.Further,the parameters of JWL-Miller EOS,determined through AUTODYN simulations,were validated by comparing airburst process simulations with experimental overpressure data.The study established a method for determining EOS parameters of high-energy propellants,achieving a high degree of accuracy.The derived parameters ensure precise modeling of propellant behavior,offering a reliable foundation for future applications in solid rocket motor performance optimization and safety assessment.
基金Projects(5127553051305462+1 种基金51535012)supported by the National Natural Science Foundation of ChinaProject(2011CB706800)supported by the National Basic Research Program of China
文摘The contact strength calculation of two curved rough surfaces is a forefront issue of Hertz contact theory and method. Associated rules between rough surface characterization parameters(correlation length, and root mean square deviation) and contact characteristic parameters(contact area, maximum contact pressure, contact number, and contact width) of two rough cylinders are mainly studied. The contact model of rough cylinders is deduced based on GW model. As there is no analytical solution for the pressure distribution equation, an approximate iterative solution method for the pressure distribution is adopted. Furthermore, the quantitative relationships among the correlation length, the root mean square deviation, the asperity radius of curvature and the asperity density are also obtained based on a numerical simulation method. The maximum contact pressure and the contact number decrease with the increase of correlation length, while the contact width and the contact area are on the contrary. The contact width increases with the increase of root mean square deviation while the maximum contact pressure, the contact area and the contact number decrease.
基金Supported by"973"Program(2002CB312104)National Natural Science Foundation of P.R.China(60375006)the Research Foundation of North China Unversity of Technology University
文摘The PnP problem is a widely used technique for pose determination in computer vision community,and finding out geometric conditions of multiple solutions is the ultimate and most desirable goal of the multi-solution analysis,which is also a key research issue of the problem.In this paper,we prove that given 3 control points,if the camera's optical center lies on the so-called“danger cylinder”and is enough far from the supporting plane of control points,the corresponding P3P problem must have 3 positive solutions.This result can bring some new insights into a better understanding of the multi-solution problem.For example,it is shown in the literature that the solution of the P3P problem is instable if the optical center lies on this danger cylinder,we think such occurrence of triple-solution is the primary source of this instability.
文摘In this study, the laminar heat transfer and nanofluid flow between two porous horizontal concentric cylinders was investigated. The problem is investigated in two different geometries and the Re=10, 25, 50, 75, 100 and volume fraction 0, 0.2%, 0.5%, 2% and 5% that related to copper nanoparticles, and porous medium porosity of 0.5 and 0.9. Compared to the first geometry, the convective coefficient in the second geometry increases by 8.3%, 7% and 5.5% at Reynolds numbers of 100, 75 and 50, respectively. Comparison of the outlet temperatures for two heat fluxes of 300 and 1200 W/m^2 indicates a 2.5% temperature growth by a fourfold increase in the heat fluxes. Also, the higher Nusselt number is associated with the second geometry occurring at porosities of 0.9 and 0.5, respectively. In both geometries, the Nusselt number values at the porosity of 0.9 are higher, which is due to the increased nanofluid convection at higher porosities. The velocity of the nanofluid experiences a two-fold increase at the outlet compared to its inlet velocity in the first geometry and for both porosities. Similarly, a three-fold increase was achieved in the second geometry and for both porosities.
基金Lyudmila Petrova for invaluable metrological support. A.I.D. also thanks RFBR grant no. 15-08-01511a
文摘We suppose that in order to maintain high accuracy of holes and to lower residual stresses after cold expansion of thick-walled cylinders, which undergo cross-section plastic deformation, it is necessary to perform axial plastic compression and subsequent cold expansion with small interferences. To test this hypothesis, we studied hoop, radial and axial residual stresses in cylinders made of carbon steel AISI 1050 with hole diameter of 5 mm, outer diameter of 15 mm and length of 30 mm by Sachs method as well as accuracy of expanded holes. It is found that double cold expansion with total interference equal to 5.1% generates hoop residual stresses with largest absolute value equal to 284 MPa and ensures high holes accuracy(IT7). After plastic compression with strain equal to 0.5 and 1% the mentioned stresses reduced to 120 and 75 MPa respectively,and accuracy of the holes reduced as well. Subsequent cold expansion with small interference equal to 0.9% helps to restore holes accuracy(IT7)gained by double cold expansion and ensure that absolute value of hoop residual stresses(177 MPa) is lower compared to double cold expansion.
基金Projects(11772357,51474103,51504092)supported by the National Natural Science Foundation of ChinaProject(2016YFC0600706)supported by the National Key Research and Development Program of China
文摘The interaction of surrounding rock with a support system in deep underground tunnels has attracted extensive interest from researchers.However,the effect of high axial stress on tunnel stability has not been fully considered.In this study,compression tests with and without confining pressure were conducted on solid specimens and hollow cylinder specimens filled with aluminium,lead,and polymethyl methacrylate(PMMA)to investigate the strength,deformation and failure characteristics of circular roadways subjected to high axial stress.The influence of the three-dimensional stress on the surrounding rock supported with different stiffness was studied.The results indicate that the strength and peak strain of hollow cylinders filled with PMMA are higher than those of hollow cylinders filled with aluminium or lead,indicating that flexible retaining is beneficial for roadway stability.The results obtained in this paper can contribute to better understanding the support failure of a buried roadway subjected to high axial stress and thus to analyzing and evaluating roadway stability.
基金supported by New Product Development of Small and Medium Business Administration(SMBA)funded by the Ministry of Education,Science and Technology (No. 2011-0021376) through the Basic Science Program of the National Research Foundation of Korea(NRF)
文摘The flow pattern behaviour of falling liquid film over three horizontal cylinders was evaluated.These flows can take three forms:discrete droplets,individual jets,and continuous sheet,and special attention is paid to the effects of the physical properties and geometrical parameters of the first two forms(droplets and jets) because these forms are more important in heat-transfer behaviour and less research has been published for these forms,The flow modes and experimental results were successfully compared with previous experimental literatures,and also the effects of liquid flow rate,tube diameter,and tube spacing on departure site spacing,in both drop and jet modes,were evaluated in the low Galileo number and high viscosity fluid(cooking oil),to help developing criteria for determining falling film modes and their transitions,and to understand the heat transfer characteristics associated with each mode.
基金supported by the International Cooperation on Technology Development Program of the Korea Institute for Advancement of Technology ( KIAT),Republic of Korea ( N0000902)
文摘Hydraulic cylinder is a primary component of the hydraulic valve systems.The numerical study of hydraulic cylinder to evaluate the stress analysis,the life assessment and the performance of operation characteristics in hydraulic cylinder were described.The calculation of safety factor,fatigue life,piston chamber pressure,rod chamber pressure and the change of velocity of piston with flow time after the beginning of hydraulic cylinder were incorporated.Numerical analysis was performed using the commercial CFD code,ANSYS with unsteady,dynamic mesh model,two-way FSI(fluid-structure interaction)method and k-εturbulent model.The internal pressure in hydraulic cylinder through stress analysis show higher than those of the yield strength.
基金Projects(50775200,50905156)supported by the National Natural Science Foundation of China
文摘The system considered in this work consists of a cylinder which is controlled by a pair of three-way servo valves rather than a four-way one.Therefore,the cylinder output stiffness is independently controllable of the output force.A discontinuous projection based adaptive robust controller (ARC) was constructed to achieve high-accuracy output force trajectory tracking for the system.In ARC,on-line parameter adaptation method was adopted to reduce the extent of parametric uncertainties due to the variation of friction parameters,and sliding mode control method was utilized to attenuate the effects of parameter estimation errors,unmodelled dynamics and disturbance.Furthermore,output stiffness maximization/minimization was introduced to fulfill the requirement of many robotic applications.Extensive experimental results were presented to illustrate the effectiveness and the achievable performance of the proposed scheme.For tracking a 0.5 Hz sinusoidal trajectory,maximum tracking error is 4.1 N and average tracking error is 2.2 N.Meanwhile,the output stiffness can be made and maintained near its maximum/minimum.
基金Projects(50874047,51074014,51174014)supported by the National Natural Science Foundation of China
文摘The stress state around circular openings,such as boreholes,shafts,and tunnels,is usually needed to be evaluated.Solutions for stresses,strains and ultimate bearing capacities of pressurized hollow cylinder are common cases.Stress analytical method for plane problem of a double-layered thick-walled cylinder subjected to a type of non-uniform pressure on the outer surface and uniform radial pressure on the inner surface is given.The power series method of complex function is used.The stress analytical solution is obtained with the assumption that two layers of a cylinder are fully contacted.The distributions of normal and tangential contact stress along the interface,tangential stress on the inner boundary and stresses in the radial direction at θ=0°,45° and 90°,are obtained.An example indicates that,when the elastic modulus of the inner layer of a double-layered thick-walled cylinder is smaller than that of the outer layer,the tangential stress is smaller than that in the corresponding point for a traditional cylinder composed of homogeneous materials.In that way,stress concentration at the inner surface can be alleviated and the stress distribution is more uniform.This is a capable way to enhance the elastic ultimate bearing capacity of thick-walled cylinder.
基金Project(2006BAJ04B04)supported by the National Science and Technology Pillar Program in the Eleventh Five-year Plan PeriodProject(2006AA05Z229)supported by the National High Technology Research and Development Program of China+1 种基金Project supportedby the Scientific Research Foundation for the Returned Overseas Chinese Scholars,State Education MinistryProject(06wk3023)supported by Hunan Science and Technology Office
文摘ABE-KONDOH-NAGANO,ABID,YANG-SHIH and LAUNDER-SHARMA low-Reynolds number turbulence models were applied to simulating unsteady turbulence flow around a square cylinder in different phases flow field and time-averaged unsteady flow field.Meanwhile,drag and lift coefficients of the four different low-Reynolds number turbulence models were analyzed.The simulated results of YANG-SHIH model are close to the large eddy simulation results and experimental results,and they are significantly better than those of ABE-KONDOH-NAGANO,ABID and LAUNDER-SHARMR models.The modification of the generation of turbulence kinetic energy is the key factor to a successful simulation for YANG-SHIH model,while the correction of the turbulence near the wall has minor influence on the simulation results.For ABE-KONDOH-NAGANO,ABID and LAUNDER-SHARMA models satisfactory simulation results cannot be obtained due to lack of the modification of the generation of turbulence kinetic energy.With the joint force of wall function and the turbulence models with the adoption of corrected swirl stream,flow around a square cylinder can be fully simulated with less grids by the near-wall.
基金Project(51674096)supported by the National Natural Science Foundation of ChinaProject(E2016203119)supported by Hebei Natural Science Foundation of ChinaProject(18211045)supported by the Key Research and Development Foundation in Hebei Province of China
文摘Cooling strength is one of the important factors affecting microstructure and properties of gas cylinders during quenching process,and reasonable water spray volume can effectively improve the quality of gas cylinders and reduce production costs.To find the optimal water spray parameters,a fluid-solid coupling model with three-phase flow was established in consideration of water-vapor conversion.The inner and outer walls of gas cylinder with the dimensions of d914 mm×38 mm×12000 mm were quenched using multi-nozzle water spray system.The internal pressure,average heat transfer coefficient(have)and stress of the gas cylinder under different water spray volumes during quenching process were studied.Finally,the mathematical model was experimentally verified.The results show that both the internal pressure and have increase along with the increase of spray volume.The internal pressure increases slowly first and then rapidly,but have increases rapidly first and then slowly.To satisfy hardenability of gas cylinders,the minimum spray volume should not be less than 40 m^3/(h·m).The results of stress indicate that water spray quenching will not cause deformation of bottle body in the range of water volume from 40 to 290 m^3/(h·m).
基金Project(51576213) supported by the National Natural Science Foundation of ChinaProject(2017JJ1031) supported by Hunan Provincial Natural Science Foundation of China+1 种基金Project(CSUZC201921) supported by the Open Sharing Fund for the Large-scale Instruments and Equipments of Central South University,ChinaProject(2019zzts536) supported by the Fundamental Research Funds for the Central Universities,China
文摘This study investigated numerically the characteristics of laminar flow around two identical circular cylinders placed in tandem, with slits of the same width through their respective axis. The center to center distance between the cylinders and the slit orientation were varied to study their effects on the flow structure, lift and drag, and vortex shedding characteristics. It was found that three flow regimes could be distinguished, the transitions between which could be indicated by the sudden changes in drag and lift. Asymmetrically, configured slits destabilized the stagnant region between cylinders;whereas in-line slits connect the two cylinders to act as a single elongated bluff body, even at large cylinder separation, by stabilizing the stagnant region in between. These in turn strongly modified the transition between flow regimes. Vortex shedding was also strongly influenced by both slit configuration and cylinder separation.
文摘Combined effects of Soret(thermal-diffusion) and Dufour(diffusion-thermo) in MHD stagnation point flow by a permeable stretching cylinder were studied. Analysis was examined in the presence of heat generation/absorption and chemical reaction. The laws of conservation of mass, momentum, energy and concentration are found to lead to the mathematical development of the problem. Suitable transformations were used to convert the nonlinear partial differential equations into the ordinary differential equations. The series solutions of boundary layer equations through momentum, energy and concentration equations were obtained.Convergence of the developed series solutions was discussed via plots and numerical values. The behaviors of different physical parameters on the velocity components, temperature and concentration were obtained. Numerical values of Nusselt number, skin friction and Sherwood number with different parameters were computed and analyzed. It is found that Dufour and Soret numbers result in the enhancement of temperature and concentration distributions, respectively.
基金Project(cstc2018jcyjAX0159)supported by the Natural Science Foundation of Chongqing,ChinaProject(51575066)supported by the National Natural Science Foundation of China。
文摘Ultra-large plate forgings are foundation of heavy machinery,but many parts of the type cannot be made by conventional technologies due to the characters of extreme manufacturing in terms of size and quality requirements.This paper introduced a systematically method called cylinder unfolding method(CUM)for producing large plate forgings,by using a serial of operations including“splitting”,“unfolding”,and“flattening”of a thick cylinder obtained from saddle forging.The technological route of CUM was presented in detail with an example of plate forging with the horizontal sizes of 6100 mm and thickness of 300 mm.The deformation features of saddle forging for fabricating transitional cylinders were analyzed,and then the subsequent handling steps including splitting,unfolding and flattening of the cylinder,as well as the auxiliary processing,were addressed.The practice proved that CUM can provide an efficient way for manufacturing ultra-large plate forgings and meet the strict requirements in geometry and mechanical performance,without highly increasing the investments of forming equipment and tooling.
文摘The optimal design of heating and cooling systems must take into account heat radiation which is a non-linear process.In this study,the mixed convection in a radiative magnetohydrodynamic Eyring-Powell copperwater nanofluid over a stretching cylinder was investigated.The energy balance is modeled,taking into account the non-linear thermal radiation and a thermal slip condition.The effects of the embedded flow parameters on the fluid properties,as well as on the skin friction coefficient and heat transfer rate,are analyzed.Unlike in many existing studies,the recent spectral quasi-linearization method is used to solve the coupled nonlinear boundary-value problem.The computational result shows that increasing the nanoparticle volume fraction,thermal radiation parameter and heat generation parameter enhances temperature profile.We found that the velocity slip parameter and the fluid material parameter enhance the skin friction.A comparison of the current numerical results with existing literature for some limiting cases shows excellent agreement.
基金Project(51305388)supported by the National Natural Science Foundation of ChinaProject(BJ2014055)supported by the Youth Talent Projects of Colleges in Hebei Province,ChinaProject(2016M590211)supported by China Postdoctoral Science Foundation
文摘Because of the mixed grain and coarse grain structure, the long heat treatment cycle and large energy conservation in the heavy cylinder heat treatment process, the up ladder type and terraced type normalizing heat treatment of heavy cylinder after rolling were put forward. The microstructure and mechanical properties of 2.25Cr1Mo0.25 V steel after the up ladder type normalizing, terraced type normalizing and isothermal type normalizing were studied. Experimental results show that： 1） For the grain refinement, the twice terraced type normalizing is better than the up ladder type and isothermal type normalizing, and the average grain size is 18 μm; 2） The yield strength, tensile strength and-30℃ charpy impact energy after twice terraced type normalizing are 681 MPa, 768 MPa and 181 J, respectively, and the mechanical properties are better than those of the up ladder type and isothermal type normalizing; 3） Compared with the isothermal type normalizing, the holding time of terraced type normalizing can be shortened by 30%, which greatly reduces the energy consumption.
